Toshiba MMU-AP0071MH User manual

OWNERS MANUAL
MANUEL DU PROPRIETAIRE
BETRIEBSANLEITUNG
MANUALE DEL PROPRIETARIO
MANUAL DEL PROPIETARIO
MANUAL DO UTILIZADOR
GEBRUIKSAANWIJZING
ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ
Indoor Unit
4-way Air Discharge Cassette Type
MMU-AP0071MH, AP0091MH, AP0121MH, AP0151MH, AP0181MH,
MMU-AP0091H, AP0121H, AP0151H, AP0181H, AP0241H,
MMU-AP0271H, AP0301H, AP0361H, AP0481H
2-way Air Discharge Cassette Type
MMU-AP0071WH, AP0091WH, AP0121WH,
MMU-AP0151WH, AP0181WH, AP0241WH,
MMU-AP0271WH, AP0301WH
1-way Air Discharge Cassette Type
MMU-AP0071YH, AP0091YH, AP0121YH,
MMU-AP0152SH, AP0182SH, AP0242SH
Concealed Duct Standard Type
MMD-AP0071BH, AP0091BH, AP0121BH, AP0151BH, AP0181BH,
MMD-AP0241BH, AP0271BH, AP0301BH, AP0361BH, AP0481BH
Slim Duct Type
MMD-AP0071SPH(SH), AP0091SPH(SH), AP0121SPH(SH),
MMD-AP0151SPH(SH), AP0181SPH(SH)
Concealed Duct High Static Pressure Type
MMD-AP0181H, AP0241H, AP0271H, AP0361H, AP0481H
Under Ceiling Type
MMC-AP0151H, AP0181H, AP0241H, AP0271H, AP0361H, AP0481H
High Wall Type
MMK-AP0071H, AP0072H, AP0091H, AP0092H, AP0121H,
MMK-AP0122H, AP0151H, AP0181H, AP0241H
Floor Standing Cabinet Type
MML-AP0071H, AP0091H, AP0121H,
MML-AP0151H, AP0181H, AP0241H
Floor Standing Concealed Type
MML-AP0071BH, AP0091BH, AP0121BH,
MML-AP0151BH, AP0181BH, AP0241BH
Floor Standing Type
MMF-AP0151H, AP0181H, AP0241H,
MMF-AP0271H, AP0361H, AP0481H
Outdoor Unit
Heat Pump Model
MCY-MAP0401HT, HT2D,
MCY-MAP0501HT, HT2D,
MCY-MAP0601HT, HT2D

ADOPTION OF NEW REFRIGERANT
This Air Conditioner is a new type which adopts a new
refrigerant HFC (R410A) instead of the conventional
refrigerant R22 in order to prevent destruction of the
ozone layer.
UTILISATION DU NOUVEAU REFRIGERANT
Ce climatiseur est d’un type inédit qui utilise le nouveau
réfrigérant HFC (R410A) au lieu du réfrigérant
traditionnel R22, afin d’éviter la destruction de la couche
d’ozone.
EINFÜHRUNG EINES NEUEN KÜHLMITTELS
Dies ist ein neuartiges Klimagerät. Anstatt des
herkömmlichen Kühlmittels R22 verwendet es das neue
ozonschicht-schonende HFC Kühlmittel R410A.
ADOZIONE DI UN NUOVO REFRIGERANTE
Questo condizionatore d'aria è di un tipo nuovo che
adotta un nuovo refrigerate HFC (R410A) al posto del
refrigerante convenzionale R22, per prevenire la
distruzione dello strato di ozono dell'atmosfera terrestre.
ADOPCIÓN DE NUEVO REFRIGERANTE
Este aparato de aire acondicionado es un modelo
reciente que incorpora el nuevo refrigerante HFC
(R410A) en lugar del refrigerante convencional R22
para así evitar daños en la capa de ozono.
ADOPÇÃO DO NOVO REFRIGERANTE
Este ar condicionado é um modelo novo que adopta um
novo refrigerante HFC (R410A) em vez do refrigerante
convencional R22 para evitar a destruição da cama de
ozono.
ÕÉÏÈÅÔÇÓÇ ÍÅÏÕ ØÕÊÔÉÊÏÕ
Ôï ðáñüí Êëéìáôéóôéêü åßíáé íÝïò ôýðïò ðïõ õéïèåôåß íÝï
øõêôéêü HFC (R410 ) óôç èÝóç ôïõ óõìâáôéêïý
øõêôéêïý R22 ðñïêåéìÝíïõ íá âïçèÞóåé óôçí ðñïóôáóßá
ôïõ üæïíôïò.
TOEPASSINGVAN EEN NIEUW KOELMIDDEL
Deze airconditioner is een nieuwe type dat werkt met
een nieuw koelmiddel HFC (R410A) in plaats van met
het conventionele koelmiddel R22, als bijdrage om de
aantasting van de ozonlaag te reduceren.
Thank you very much for purchasing TOSHIBA Air Conditioner.
Please read this owner's manual carefully before using your Air
Conditioner.
• Be sure to obtain the “Owner’s manual” and “Installation manual” from
constructor (or dealer).
Request to constructor or dealer
Please clearly explain the contents of the Owner’s manual and hand over it.
Nous vous remercions pour avoir choisi un climatiseur TOSHIBA.
Veuillez lire attentivement ce Manuel du propriétaire avant d’utiliser votre
climatiseur.
• Assurez-vous que le constructeur (ou le revendeur) vous remette le
“Manuel du propriétaire” et le “Manuel d’installation”.
Demande au constructeur ou au revendeur
Veuillez expliquer clairement le contenu du Manuel du propriétaire et le
remettre au client.
Wir danken Ihnen, dass Sie sich für einTOSHIBA Klimagerät entschieden
haben.
Bitte lesen Sie diese Betriebsanleitung, bevor Sie Ihr Klimagerät benutzen, sorgfältig.
• Lassen Sie sich die “Betriebsanleitung” und das “Installations-Handbuch”
unbedingt vom Installateur oder vom Lieferanten aushändigen.
Eine Bitte an den Installateur oder Lieferanten:
Bitte erklären Sie dem Käufer den Inhalt der Betriebsanleitung und händigen
sie ihm aus.
Grazie di aver acquistato un condizionatore d'aria TOSHIBA.
Prima di usare il condizionatore d'aria, leggere con attenzione questo
manuale del proprietario.
• Si raccomanda di tenere a portata di mano il “Manuale del proprietario”
e il “Manuale di installazione” ricevuti dal produttore (o dal rivenditore).
Richiesta al produttore o al rivenditore
Spiegare chiaramente il contenuto del Manuale del proprietario e
consegnarne una copia all'utente.
Muchas gracias por haber adquirido el aparato de aire acondicionado TOSHIBA.
Lea atentamente este manual del propietario antes de utilizar el aparato de aire
acondicionado.
• Asegúrese de que el fabricante (o distribuidor) le proporcione el “Manual del
propietario” y el “Manual de instalación”.
Solicitud al fabricante o distribuidor
Explique con claridad el contenido del Manual del propietario y entréguelo al
cliente.
Muito obrigada por adquirir o Ar Condicionado TOSHIBA.
Leia atentamente este manual do utilizador antes de utilizar o seu ar
condicionado.
• Não se esqueça de receber o “Manual do utilizador” e o “Manual de
inslatação” do fabricante (ou agente).
Pedido ao fabricante ou agente
Explique por favor o conteúdo do Manual do utilizador e entregue-o.
Hartelijk dank voor uw keuze voor een airconditioner van TOSHIBA.
Lees deze gebruiksaanwijzing zorgvuldig door voordat u de
airconditioner gaat gebruiken.
• Zorg ervoor dat u zowel de ‘gebruiksaanwijzing’als de
‘installatiehandleiding’ van de installateur (of leverancier) krijgt.
Verzoek aan de installateur of de leverancier
Leg de inhoud van de gebruiksaanwijzing duidelijk uit en overhandig de
gebruiksaanwijzing nadien aan de klant.
Óáò åõ÷áñéóôïýìå ðïëý ðïõ ðñïôéìÞóáôå ãéá ôçí áãïñÜ óáò Ýíá
Êëéìáôéóôéêü TOSHIB .
Ðáñáêáëïýìå äéáâÜóôå ðñïóå÷ôéêÜ ôéò ïäçãßåò ÷ñÞóçò ðñéí áðü ôç ÷ñÞóç
ôïõ Êëéìáôéóôéêïý.
 Âåâáéùèåßôå üôé ï êáôáóêåõáóôÞò (Þ ï ðùëçôÞò) óáò ðáñÝäùóå êáé ôéò
Ïäçãßåò ×ñÞóçò êáé ôï Åã÷åéñßäéï ÅãêáôÜóôáóçò.
ÐáñÜêëçóç ãéá ôïí êáôáóêåõáóôÞ Þ ôïí ðùëçôÞ
Ðáñáêáëþ åîçãÞóôå ìå óáöÞíåéá ôá ðåñéå÷üìåíá ôùí Ïäçãéþí ×ñÞóçò êáé
ðáñáäþóôå ôï.
HFC
R410A R22

ITALIANO
ESPAÑOLPORTUGUÊSÅËËÇÍÉÊÁ FRANCAISDEUTSCHNEDERLANDS ENGLISH
CONTENTS
SOMMAIRE
INHALT
INDICE
CONTENIDO
ÍNDICE
ÐÅÑÉÅ×ÏÌÅÍÁ
INHOUD
PRECAUTIONS FOR SAFETY .............................................................1
NAME OF EACH PART .........................................................................3
PARTS NAME OF REMOTE CONTROLLER ........................................6
CORRECT USAGE ................................................................................8
ADJUSTMENT OF WIND DIRECTION ..................................................9
TIMER OPERATION ............................................................................16
INSTALLATION....................................................................................17
MAINTENANCE...................................................................................18
AIR CONDITIONER OPERATIONS AND PERFORMANCE...............22
RE-INSTALLATION .............................................................................23
WHENTHE FOLLOWING SYMPTOMS ARE FOUND ........................24
MESURES DE SECURITE ..................................................................26
NOM DE CHAQUE PIÈCE...................................................................28
NOM DES PIECES DE LATELECOMMANDE ...................................31
UTILISATION CORRECTE .................................................................. 33
REGLAGE DU SENS DE SOUFFLAGE..............................................34
FONCTIONNEMENT PAR MINUTERIE ..............................................41
INSTALLATION....................................................................................42
ENTRETIEN.........................................................................................43
FONCTIONNEMENT ET PERFORMANCES DU CLIMATISEUR .......47
REINSTALLATION...............................................................................48
EN PRÉSENCE DES SYMPTÔMES SUIVANTS ................................49
SICHERHEITSVORKEHRUNGEN ......................................................51
BEZEICHNUNGEN DERTEILE ..........................................................53
TEILEBEZEICHNUNG DER FERNBEDIENUNG ................................56
RICHTIGE HANDHABUNG .................................................................58
EINSTELLUNG DES LUFTSTROMS ..................................................59
ZEITBETRIEB......................................................................................66
INSTALLATION....................................................................................67
WARTUNG...........................................................................................68
FUNKTIONEN UND LEISTUNG DES KLIMAGERÄTS ......................72
NEU-INSTALLATION ...........................................................................73
VORGEHENSWEISE BEI FOLGENDEN SYMPTOMEN ....................74
PRECAUZIONI PER LA SICUREZZA .................................................76
NOME DI OGNI PARTE .......................................................................78
NOME DELLE PARTI DELTELECOMANDO .....................................81
USO CORRETTO ................................................................................83
REGOLAZIONE DELLA DIREZIONE DELL’ARIA ..............................84
FUNZIONAMENTO CONTIMER .........................................................91
INSTALLAZIONE ................................................................................. 92
MANUTENZIONE ................................................................................93
OPERAZIONI E PRESTAZIONI DEL CONDIZIONATORE D’ARIA ....97
RE-INSTALLAZIONE...........................................................................98
QUANDO SI RISCONTRANO I SINTOMI SEGUENTI ........................99
PRECAUCIONES PARA SU SEGURIDAD .......................................101
NOMBRE DE CADA COMPONENTE ...............................................103
DESCRIPCIÓN DE LOS BOTONES DEL CONTROL REMOTO ......106
UTILIZACIÓN CORRECTA................................................................108
AJUSTE DE LA DIRECCIÓN DEL AIRE ..........................................109
FUNCIONAMIENTO DELTEMPORIZADOR.....................................116
INSTALACIÓN ...................................................................................117
MANTENIMIENTO .............................................................................118
FUNCIONESY RENDIMIENTO DEL APARATO DE AIRE
ACONDICIONADO ............................................................................122
REINSTALACIÓN ..............................................................................123
CUANDO SE DETECTAN LOS SIGUIENTES SÍNTOMAS ............... 124
PRECAUÇÕES DE SEGURANÇA ....................................................126
NOMES DE CADA PEÇA ..................................................................128
NOME DAS PEÇAS DO CONTROLADOR REMOTO.......................131
UTILIZAÇÃO CORRECTA ................................................................133
REGULAÇÃO DA DIRECÇÃO DO VENTO.......................................134
OPERAÇÃO DOTEMPORIZADOR ..................................................141
INSTALAÇÃO ....................................................................................142
MANUTENÇÃO .................................................................................143
FUNCIONAMENTO E PERFORMANCE DO APARELHO DE AR
CONDICIONADO...............................................................................147
REINSTALAÇÃO ...............................................................................148
SE FOREM DETECTADOS OS SEGUINTES SINTOMAS ...............149
VOORZORGSMAATREGELENVOOR UWVEILIGHEID .................151
BENAMINGENVAN DE ONDERDELEN...........................................153
BENAMING VAN DE ONDERDELEN VAN DE
AFSTANDSBEDIENING .................................................................... 156
CORRECT GEBRUIK ........................................................................158
INSTELLENVAN DE LUCHTSTROOMRICHTING ...........................159
DETIMER GEBRUIKEN .................................................................... 166
INSTALLEREN ..................................................................................167
ONDERHOUD....................................................................................168
BEDIENING ENWERKING VAN DE AIRCONDITIONER .................172
OPNIEUW INSTALLEREN ................................................................173
WANNEER DEVOLGENDE SYMPTOMEN AANWEZIG ZIJN .........174
ÐÑÏÖÕËÁÎÅÉÓ ÃÉÁ ÁÓÖÁËÅÉÁ ....................................................... 176
ÏÍÏÌÁÓÉÁ ÔÏÕ ÊÁÈÅ ÅÎÁÑÔÇÌÁÔÏÓ ........................................ 178
ÏÍÏÌÁÓÉÁ ÔÌÇÌÁÔÙÍ ÔÏÕ ÔÇËÅ×ÅÉÑÉÓÔÇÑÉÏÕ ...................... 181
ÏÑÈÇ ×ÑÇÓÇ ..................................................................................... 183
ÑÕÈÌÉÓÇ ÔÇÓ ÊÁÔÅÕÈÕÍÓÇÓ ÔÏÕ ÁÍÅÌÏÕ .............................. 184
ËÅÉÔÏÕÑÃÉÁ ×ÑÏÍÏÄÉÁÊÏÐÔÇ ...................................................... 191
ÅÃÊÁÔÁÓÔÁÓÇ .................................................................................. 19
ÓÕÍÔÇÑÇÓÇ ....................................................................................... 193
ËÅÉÔÏÕÑÃÉÅÓ ÊÁÉ ÁÐÏÄÏÓÇ ÔÏÕ ÊËÉÌÁÔÉÓÔÉÊÏÕ .................... 197
ÅÃÊÁÔÁÓÔÁÓÇ ÅÊ ÍÅÏÕ ................................................................. 198
ÏÔÁÍ ÐÁÑÁÔÇÑÇÈÏÕÍ ÔÁ ÐÁÑÁÊÁÔÙ ÓÕÌÐÔÙÌÁÔÁ ........... 199

1
SAFETY PRECAUTIONS
WARNING
Warning on installation
Ensure the unit is installed by qualified personnel.
Specialist knowledge and technology is required to install the unit.
Do not perform the installation by yourself. If an incomplete installation is per-
formed, a fire, electric shock, injury, or water leakage may be caused.
For products that are sold separately, ensure they meet the Toshiba
specification.
For products sold separately, be sure to use those specified byToshiba.
Otherwise, a fire, electric shock or water leakage may occur. For installation
work, leave it to special engineer.
Wheninstallingtheunitinside a smallroom,takeprecautionssothatthe
refrigerantwillnot exceedthecriticalconcentrationifaleakoccurs.
Warning on use
Do not expose your body directly to excessive cool air for long
periods of time.
May effect your physical condition, causing possible health problems.
Never insert a finger or another object into the air inlet port or the air
outlet port of the air conditioner.
Since the fan rotates at a high speed inside the unit, a possible injury may be
caused.
If a fault/error (burnt smell, etc.) occurs, stop the operation, turn off
the power switch and contact the dealer who you
purchased the air conditioner from.
If the unit is allowed to keep running, a fire or electric shock could occur.
Warning on moving/repair
Do not modify the air conditioner in anyway.
As a fire or electric shock may occur.
If the unit requires maintenance or repair, contact the dealer who you
purchased the air conditioner from.
If an incomplete repair is performed, a fire or electric shock may be caused.
When moving or re-installing the air conditioner, contact the dealer
who you purchased the air conditioner from or contact a suitable
engineer.
If an incomplete installation is performed, a fire, electric shock, injury or water
leakage may occur.
CAUTION
Ensure that the unit is installed correctly by a trained engineer. If the unit is incorrectly installed, refrigerant
may leak causing possible oxygen deficiency.
Ensure that the unit is earthed correctly.
The unit must be earthed correctly, if not an electric shock may occur.(for details conform to your local build-
ingregulations)

2
CAUTION
Caution on installation
Ensure that the drain pipe is installed so that the water can run
freely and without leakage.
If the piping is fitted incorrectly, water may drip, causing possible damage to
furniture, carpets etc.
Check the earth leakage breaker is installed.
It is necessary to attach an earth leakage breaker. Otherwise, you have no
protection against a possible electric shock.
Check the air conditioner is installed in a place where flammable
gases will not leak.
If gas leaks and accumulates in the unit surroundings, an outbreak of fire
may be caused.
Check the outdoor unit is fixed securely to the base.
If it is not fixed securely to the base, the unit may become unstable and fall,
causing possible injury.
Check fixing method
Do not clean the air conditioner with water.
An electric shock may be caused.
Ensure items that are combustible are not placed in the direction
where the air conditioner will flow directly.
Imperfect combustion of the combustible items may occur.
If there are combustible items within the room, ensure that the
room has adequate ventilation, while the air conditioner is in
operation.
If ventilation is inadequate a shortage of oxygen may occur.
Check that the installation plate, etc. is not damaged by long
term use of the air conditioner.
If the installation location deteriorates sufficiently, then the unit may become
unstable and fall, resulting in possible injury.
Do not put either plants or animals in a location, where the air
conditioner flows air directly.
An adverse effect may occur, resulting in possible damage or injury to the
plant/animal.
Do not locate or spray flammable gases etc. near or directly at the
air conditioner.
A fire may be caused.
Do not put vessels containing water such as a vase on the unit.
Moisture may enter the unit, causing a deterioration of the units electrical
isolation properties, causing a possible electric shock.
Do not handle the switches with wet hands.
An electric shock may be caused.
Do not use the air conditioner for special purpose such as stor-
age of foods, plants and animals, precise equipment and art
works.
Deterioration or damage to the goods may occur.
ENGLISH

3
2-way discharge/3-way discharge
2-way discharge or 3-way discharge can be
selected according to the shape or
arrangement of the room.
For details, consult with the dealer which you
have purchased the air conditioner.
Air outlet/Air outlet flap
Select air blow direction in cooling or
heating operation each.
Earth screw
It is included in the electric
parts box.
Air outlet/Air outlet flap
Select air blow direction in cooling or
heating operation each.
Air filter
Removes dust and trash.
(Air filter is provided in the air grille.)
Air inlet grille
Air in the room is sucked from here.
Clip
The clip is to open/close the
air inlet grille.
Air inlet
Air in the room is
sucked from here.
Air filter
Removes dust and trash.
(Air filter is provided in the center panel.)
Earth screw
It is included in the electric parts box.
Center panel
Air outlet/Air outlet flap
Select air blow direction in cooling or
heating operation each.
Indoor unit
[4-way Air Discharge CassetteType]
MMU-AP0091H, AP0121H, AP0151H, AP0181H, AP0241H,
MMU-AP0271H, AP0301H, AP0361H, AP0481H, AP0561H
[2-way Air Discharge CassetteType]
MMU-AP0071MH, AP0091MH, AP0121MH, AP0151MH, AP0181MH
Air inlet
They are provided at front,
rear, left, and right sides.
Fixing leg
Air outlet (Discharge)
Hot air is discharged when cooling operation is performed.
Cold air is discharged when heating operation is performed.
Power source hole
Refrigerant pipe
connecting hole
Connecting valve is
included inside here.
Outdoor unit
Air filter
Removes dust and trash.
(Air filter is provided in the air grille.)
Air inlet grille
Air in the room is sucked from here.
Clip
The clip is to open/close the
air inlet grille.
Earth screw
It is included in the electric
parts box.
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
CODE No.
UNIT No.
TEST SETTING
DATA SET
R.C. No.
H
˚C
TEST
SETTING
NAME OF EACH PART Sold Separately Parts
Wired remote controller
RBC-AMT31E
Simple wired remote controller
RBC-AS21E2
Wireless remote controller kit
TCB-AX21E2 RBC-AX22CE2 RBC-AX21U(W)-E2

4
WEEKLY TIMER
ERROR
SuMoTuWeTh Fr Sa
PROGRAM1
PROGRAM2
PROGRAM3
SELECT ZONE
CL
SET
GROUP
CODE
No.
UNIT No.
No.
R.C.
TEST
ZONE
ALL
ZONE
GROUP
SETTING
1234
SET DATA
Weekly timer
RBC-EXW21E2
Central remote controller
TCB-SC642TLE2
Earth screw
It is included in the
electric parts box.
Air outlet/ Air outlet flap
Select air blow direction incooling
or heating operation each.
Air inlet grille
Air in the room is sucked from here.
Air filter
Removes dust and trash.
(Air filter is provided in the air inlet grille.)
[1-way Air Discharge CassetteType]
MMU-AP0071YH to AP0121YH
MMU-AP0152SH, AP0182SH, AP0242SH
Button
Button to open/close
suction port
Air outlet/Air outlet flap
Change the direction of the air to be
discharged according to cool/heat mode.
Air filter
Removes dust or trash.
(Provided on the suction port.)
Suction port
Sucks air inside of the room from here.
Earth screw
It is included in the electric parts box.
Air filter
Removes dust or trash.
(Provided on the suction port.)
[Concealed Duct StandardType]
[Concealed Duct High Static PressureType]
[Slim DuctType]
Air outlet flange
Discharge duct is
connected.
Earth screw
Earth screws are provided
in the electric parts box.
Air filter
Removes dust and trash.
(Air filter is provided in the air inlet grille.)
Air inlet
Air in the room is sucked from here.
Air outlet
Discharge duct is connected.
Air inlet
Suction duct is connected.
Earth screw
Earth screws are provided
in the electric parts box.
Drain pan
Air inlet
Suction duct is connected.
Earth screw
It is included in the electric
parts box.
Air filter
(Air filter is not provided to
some models in the series.)
Air outlet
Discharge duct is
connected.

5
Air outlet/Air outlet flap
Exchanges the air direction according to
cooling or heating time.
Earth screw
It is prepared in the electric parts box.
Air inlet port
Sucks air inside of the room from here.
Air filter
Removes dirt or dust.
(It is included in the suction port.)
Air outlet port
Drain pan (With drain filter)
This accessory is installed at the local site.
Air filter
Removes dirt or dust.
(It is included in the suction port.)
Air inlet port
Sucks air inside of the room from here.
Earth screw
It is prepared in the electric parts box.
Earth screw
It is prepared in the electric parts box.
Front panel (Lower side)
Fixing metal holder
Vertical flap
The air can be automatically discharged
rightward/leftward at stated periods.
Horizontal flap/Air outlet port
Exchanges the air direction according
to cooling or heating time.
Air filter
Removes dirt or dust.
Air inlet port
Sucks air inside of the room from here.
Fixing metal holder (Right and left)
Drain pan
Water accumulated in the drain pan is
drained from here through the drain pipe.
[Under CeilingType]
[HighWallType]
MMK-AP0071H to AP0241H
MMK-AP0072H to AP0122H
Air inlet grille
Air in the room is sucked from here.
Earth screw
Earth screws are provided in the electric
parts box.
Air filter
Removes dust and trash.
(Air filter is provided in the air inlet grille.)
Air outlet/Air outlet flap
Change the direction of the air to be
discharged according to cool/heat mode.
Button
Button to open/close the suction port
Air filter
Removes dust or trash.
(Provided on the suction port.)
Air inlet port
The air in the room is sucked in from this
port.
Earth screw
Earth screws are provided in the electric
parts box.
Air outlet/Air outlet flap
Change the direction of the air to be discharged according to cool/heat mode.
Air inlet grille
Air in the room is sucked from here.
Earth screw
Earth screws are provided in the electric
parts box.
Air outlet/Air outlet flap
Change the direction of the air to be
discharged according to cool/heat mode.
Air filter
Removes dust and trash.
(Air filter is provided in the air inlet grille.)
[Floor StandingType]
[Floor Standing ConcealedType]
[Floor Standing CabinetType]

6
Display
section
Operation
section
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
CODE No.
UNIT No.
TEST SETTING
DATA SET
R.C. No.
H
2
15
5
78 9
3
1
4
6
10
11 13
16
12 14
17
CODE No.
UNIT No.
TEST SETTING
DATA SET
R.C. No.
H
PARTS NAME OF REMOTE CONTROLLER
Display section
In the display example, all indicators are displayed for the explanation.
In reality only, the selected contents are displayed.
•When turning on the leak breaker for the first time, [SET DATA] flashes on
the display part of the remote controller. While this display is flashing, the
model is being automatically confirmed. After the [SET DATA] display has
disappeared, you may use the remote controller.
1 SET DATA display
Displayed during the setup of the timer.
2 Operation mode select display
The selected operation mode is displayed.
3 CHECK display
Displayed while the protective device works
or a fault/error occurs.
4 Timer time display
Time on the timer is displayed.
(When a fault/error occurs, the check code is
displayed.)
5 Timer setting setup display
When pushing the Timer setting button, the
display on the timer is selected in order of
[OFF] →[OFF] repeat OFF timer
→[ON] →No display.
6 Filter display
If “FILTER ”is displayed, clean the air
filter.
7 TEST run display
Displayed during a test run.
8 Flap position display
(for 4-Way Air Discharge CassetteType and
Under CeilingType model only)
Displays flap position.
9 SWING display
Displayed during the up/down movement of the
flap.
10 Set up temperature display
The selected set up temp. is displayed.
11 Remote controller sensor display
Displayed while the sensor on the remote
controller is used.
12 PRE-HEAT display
(for Heat-pump model only)
Displayed when the heating operation starts or a
defrost operation is carried out.
While this indication is displayed, the indoor fan
will stop or will go into LOW mode.
13 Operation ready display
Displayed when cooling or heating operation is
impossible because the outdoor temperature goes
out of the operable range.
14 No function display
Displayed if there is no function even when the
button is pushed.
15 Air volume select display
The selected air volume mode is displayed.
(AUTO) (HIGH)
(MED.) (LOW)
In the Concealed Duct High Static Pressure type
models, [HIGH] only is displayed for the air speed.
16 Mode select control display
Displayed when pushing the “Operation mode
select ”button while the operation mode is
fixed in heating or cooling mode by the system
manager of the air conditioner.
17 Central control display
Displayed when using the remote controller to-
gether with a central control remote controller.
If the Remote controller is prohibited at the central
control side, flashes when operating the
ON / OFF
,
MODE
, / buttons.The change
will not be accepted.
(The contents available to be set up on the remote
controller differ according to the central control
mode. For details, refer to Owner’s Manual of the
central control remote controller.)

7
17
3
5
2
8
9
6
4
10
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
Operation section
Push each button to select a desired operation.
This remote controller can operate a maximum of 8 indoor units.
•Before the unit can begin operation, it is firstly necessary to set the units operating parameters. After this
has been completed the air conditioner can be used by pushing the
ON / OFF
button only.
1 Air volume select button
Selects the desired air volume mode.
For the Concealed Duct High Static Pressure
type models this function is unavailable.
2 Timer set button
TheTIMER SET button is used when the timer
is set up.
3 Check button
The CHECK button is used to check the units
operation. During normal operation, do not use
this button.
4 Fan
VENT
button
The
VENT
button is used when a fan which is
sold on the market is connected.
•If is displayed on the remote controller
when pushing the
VENT
button, a fan is not
connected.
5 Filter reset button
Resets (Erases) the “FILTER ”display.
6 Air flow direction and Swing function
UNIT
:
If there are multiple indoor units that are con-
trolled by a single remote controller, simply
select each unit in turn for which you wish to
adjust the air flow direction.
SWING/FIX
:
Set up the auto swing and the angle of the flap.
•This function is not provided on the Concealed
Duct StandardType, High Static Pressure
Type, Floor standing CabinetType, Floor
Standing ConcealedType, or Slim DuctType.
7 Operation lamp
The light will be ON when the unit is in opera-
tion and OFF when the unit is not being used.
Note)The light will flash if a protective device
has been operated or if the timer function has
anerror.
8
ON / OFF
button
When the button is pushed, the operation
starts.If the button is pressed again, the unit
operation will stop.
When the unit operation has stopped, the
operation lamp and all of the displays will
disappear.
9 Operation select button
Selects the desired operation mode.
10 Set up temperature button
Adjusts the room temperature.
Set the desired set temperature by pushing
the or buttons.
OPTION :
Remote controller sensor
In normal installations the temperature of the room
is sensed by a temperature sensor on the indoor
unit. However it is possible to have the sensor
within your remote controller.For further details
please contact your local dealer.
•In cases where one remote controller controls the
multiple indoor units, the setup operation is
unavailable in group control.

8
1
3 2
4
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
HEAT DRY COOL FAN
Heat-pump model
DRY COOL FAN
Cooling only model
(Dehumidity)
LOWMED.HIGH AUTO
CORRECT USAGE
When you use the air conditioner for the first time or when you change the SET DATA value, follow the proce-
dure shown below.For consequent uses the display on the remote controller can be turned on by pushing the
ON / OFF
button only.
Preparation
Turn on the main power supply and/or the leakage breaker.
•When the power supply is turned on, a partition line is shown on the display part of the remote controller.
Note)When the power supply is turned on, the remote controller will not accept any operational inputs until
approximately 1 minute has passed.This is not a failure of the unit.
REQUIREMENT
•While using the air conditioner, only operate it with the
ON / OFF
button.Do not turn it off with the main
power switch or the leakage breaker.
•Do not turn off the leakage breaker while the air conditioner is in use.
•Turn on the leakage breaker 12 hours or more before the air conditioner is to begin operation or if the
system has not been in use for long periods of time.
1 Push the
ON / OFF
button.
The operation lamp goes on, and the operation will start.
2 Select an operation mode with the
MODE
button.
One push of the button, and the display
changes in the order shown on the right.
•“DRY mode”function is not provided on the
Concealed Duct High Static PressureType.
3 Select the air volume with the
FAN
button.
One push of the button, and the display
changes in the order shown on the right.
•When the air volume is set to“AUTO ”, the air volume will differ according to the room temperature.
•In DRY mode, the “AUTO ”symbol will be displayed and the air volume will be LOW.
•In heating operation, if the room temperature is not heated sufficiently with the air volume set at “LOW
”operation, select the “MED. ”or“HIGH ”operation.
•The temperature sensor for the indoor unit is located near to the air inlet opening and therefore will differ
slightly from the actual room temperature.This difference may be increased/decreased depending on the
type of room and its design.(Automatic air speed cannot be selected in FAN mode.)
•The AirVolume function is not provided on the“Concealed Duct High Static PressureType”instead the
air speed “HIGH ”symbol is displayed.
4 Determine the set up temperature by pushing the “TEMP. ” or “TEMP. ” button.
Stop
Push the
ON / OFF
button.
The operation lamp goes off and the unit will stop.

9
REQUIREMENT
[In Cooling operation]
•The operation will start after approximately 1 minute.
[In Heating operation (For Heat-pump model only)]
•In heating operation, the fan operation may continue for approximately 30 seconds after the air condi-
tioner has stopped.
•The indoor fan will continue the preheat operation for 3 to 5 minutes under stop conditions.The indoor
unit will then begin to blow out hot air.
(symbol on the remote controller display will come on.)
•When the temperature of the room has reached the setup temperature and the outdoor unit stops, the air
speed reduces and so the air volume will decrease.
•In HEAT mode, if the room temperature reaches the set temperature, the outdoor unit will stop and
the air flow / volume will decrease.
•In the defrost mode, the fan will stop so that cool air is not discharged and the PRE-DEF is displayed.
ADJUSTMENT OF WIND DIRECTION
To increase the cooling or heating effect, be sure to use the discharge flap in different direc-
tions when in cooling or heating operation.
The characteristics of air are such that cold air will accumulate in the lower half of the room, while hot air will
accumulate in the upper half.
CAUTION
Set the flap horizontally in cooling operation.
If a cooling operation is performed with a downwards discharge, the surface of the discharge port or flap
will become wet with dew, and water may drip down.
REQUIREMENT
•If a heating operation is performed with a horizontal discharge, unevenness the room temperature may
not be equal i.e.there may be a large variance between one side of the room with the other.
4-way Air Discharge CassetteType
•When the air conditioner is not in operation, the
discharge flap will automatically directs downwards.
•When the air conditioner is in ready status for heat-
ing, the discharge flap will be directed upwards.
The swinging operation will begin after heating
ready status has been cleared. Please note the
“SWING ” symbol will still be displayed on the
remote controller even when the unit status is ready
to begin the heating operation.
[In Cooling operation]
Use the discharge flap with a horizontal set point.
[In Heating operation (For Heat-pump model only)]
Use the discharge flap with a downwards set point.

10
Initial setup
Initial setup
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
In FAN operation
1, 2, 3 4
In all modes
Display when stopping the swing
Initial setup
Series of
operation
Fan/Heat
operation Cool/Dry operation
Unit No. 1-1No display Unit No. 1-2
Unit No. 1-4 Unit No. 1-3
How to set up the air direction
Push
SWING/FIX
button.
1 Every pushing the button, the air direction changes.
In Heating operation
Set the air outlet flap downward.
If directing it upward, the hot air may not come to the foot.
How to adjust the the air flow direction,
using the swinging function
2 Push the
SWING/FIX
button.
Set the direction of the air outlet flap to
the lowest position and then push the
SWING/FIX
button again.
•[SWING ] is displayed and the air flow
direction will automatically change either
upwards/downwards.
In the case where one remote controller con-
trols multiple indoor units, each indoor unit can
be selected and its air flow direction can be
adjusted.
How to stop the flap from swinging
3 Push the
SWING/FIX
button again while the
horizontal flap is moving.
•The horizontal flap can be stopped at any
position desired. If you wish to return the flap to
it original upwards position, press the
SWING/FIX
button again.
* During the cooling/drying operation the hori-
zontal flap will not stop at its most downwards
facing position 9 (reduce the risk of water
dripping), but will instead move to the 3rd
position from the top (as shown in the figure).
4
UNIT
•To set up the air flow direction individually,
push the
UNIT
button to display each indoor
unit No.in a group control.You can then set the
air flow direction for the displayed indoor unit.
•If there is no display, all the indoor units can be
operated collectively.
•For every push of the
UNIT
button, the display
will alter between units as shown in the figure.
In Cooling / Dry operation
Set the air outlet flap Upwards.
If directing it downwards, the dew may form on the near side of the air discharge
port and could drip.

11
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
1, 2 3
Unit No.1-1No display Unit No.1-2
Unit No. 1-4 Unit No. 1-3
Based on the shape or arrangement of the room, the cold air and hot air can be discharged in two directions or
three directions.For details, please contact your local dealer.
INFORMATION
•If cooling operation is performed with a downwards discharge, dew may form on the surface of the
cabinet or the horizontal flap resulting in dripping.
•If heating operation is performed with a horizontal discharge, the room temperature may not be equal i.e.
there may be a large variance between one side of the room with the other.
•Do not move the horizontal flap directly with your hands; otherwise a fault maybe caused. Select the
direction of the horizontal flap using the flap operation switch on the remote controller.The horizontal flap
will not stop immediately, even if the switch is pushed.
Note) Pushing the switch again when the required louver direction has been reached will stop the louver.
2-way Air Discharge CassetteType
[In Cooling operation]
Use the air outlet flap with a horizontal set point.
[In Heating operation (For Heat-pump model only)]
Use the air outlet flap with a downwards set point.
Setup of air flow direction and swinging function
1 Push the
SWING/FIX
button during operation.
•[SWING ] is displayed and the air flow direction will automatically change either upwards/downwards.
In the case of one remote controller that controls multiple indoor units, each indoor unit can be selected
and its air flow direction can be adjusted.
2 Push the
SWING/FIX
button again during the swinging
of the air outlet flap.
•The air outlet flap will be stopped at the desired position.
3
UNIT
•To set up the air flow direction individually, push the
UNIT
button to display each indoor unit No.in a group
control.You can then set the air flow direction for the
displayed indoor unit.
•If there is no display, all the indoor units can be oper-
ated collectively.
•For every push of the
UNIT
button, the display alters
between units, as shown in the figure.
1-way Air Discharge CassetteType
Adjustment of air flow direction upwards/downwards
[In Cooling operation]
In cooling operation, use the air outlet flap with a horizontal set point
so that the cold air diffuses the whole room.
[In Heating operation (For Heat-pump model only)]
In heating operation, use the air outlet flap with a downwards set
point so that the hot air is directed towards the floor.
Adjustment of air flow direction rightwards/leftwards
To change the discharge direction to right or left side, set the verti-
cal grille inside of the air outlet flap to the desired direction.
Setup the air flow direction and swinging function
Refer to the description of the “2-way Air Discharge CassetteType”.

12
Initial setup Initial setup
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
In FAN operation
1, 2, 3 4
In all modes
Display when stopping the swing
Initial setup
Series of
operation
Fan/Heat
operation Cool/Dry operation
Unit No. 1-1No display Unit No. 1-2
Unit No. 1-4 Unit No. 1-3
Under CeilingType
•While the air conditioner is not in operation, the horizontal flap (Up/Down air direction
adjustment plate) will automatically point upwards.
•When the air conditioner is in ready status for heating, the horizontal flap (Up/Down air
direction adjustment plate) will points upwards.The swinging operation will begin after the
heating ready status has been cleared. Please note the “SWING ” symbol will still be
displayed on the remote controller even when the status is ready to heat.
How to adjust the air flow direction
Push the
SWING/FIX
button during operation.
1 Every time you push the button the air
flow direction will change.
How to adjust the air flow direction, using
the swinging function
2 Push the
SWING/FIX
button.
Set the direction of the horizontal flap (Up/
Down air direction adjustment plate) to its
lowest position and then push the
SWING/FIX
button again.
•[SWING ] is displayed and the air direction will
automatically upwards or downwards.
In cases where one remote controller controls
multiple indoor units, it is possible to set each
indoor unit individually, so that the air flow direc-
tion can be altered.
How to stop the louver from swinging
3 Push the
SWING/FIX
button again while the hori-
zontal flap is moving
•The horizontal flap can be stopped at any position
desired. If you wish to return the louvre to it original
upwards position, press the
SWING/FIX
button again.
* During the cooling/drying operation the horizon-
tal flap will not stop at its most downwards
facing position 9 (reduce the risk of water
dripping), but will instead move to the 3rd
position from the top (as shown in the figure).
4
UNIT
•To set up the air flow direction individually, push
the
UNIT
button to display each indoor unit No.in
a group control.You can then set the air flow
direction for the displayed indoor unit.
•If there is no display, all the indoor units can be
operated collectively.
•For every push of the
UNIT
button, the display
will alter between units as shown in the figure.
In Cooling / Dry operation
Set the horizontal flap (Up/Down
air direction adjustment plate)
upwards. If directing the air flow
downwards, condensation may
form on the surface of the louver
and may cause water to drip.
In Heating operation
Set the horizontal flap (Up/Down
air direction adjustment plate)
downwards. If the air flow is directed
upwards, the hot air may not reach
the floor, creating an uneven
temperature within the room.

13
Right/Left air direction adjustment
To change the air outlet direction to the right or left side, set the vertical flap located behind the horizontal flap
to the desired direction.
INFORMATION
•If cooling operation is performed with a downwards discharge,
dew may form on surface of the cabinet or the horizontal flap
resulting in possible dripping.
•If heating operation is performed with a horizontal discharge,
the room temperature may not be equal i.e. there may be a
large variance between one side of the room with the other.
HighWallType
Adjustment of air flow direction upwards/downwards
[In Cooling operation]
In cooling operation, use the horizontal flap with a horizontal set point
so that the cold air diffuses the whole room.
[In Heating operation (For Heat-pump model only)]
In heating operation, use the horizontal flap with a downwards set
point so that the hot air blows towards the floor.
REQUIREMENT
•If cooling operation is performed with the louver set at a down-
wards position, dew may form on the surface of the cabinet or
the horizontal flap resulting in possible dripping.
•If heating operation is performed with the louver set in a hori-
zontal position, the room temperature may not be equal i.e.
there may be a large variance between one side of the room
with the other.
•Do not move the horizontal flap directly with your hands; other-
wise a fault/error may be caused. Select the direction of the
horizontal flap using the
SWING/FIX
button on the remote controller.
The horizontal flap will not stop immediately even if the switch
is pushed.
Note) Pushing the switch again when the required louver direc-
tion has been reached will stop the louver.
Adjustment of air flow direction rightwards/leftwards
To change the air outlet direction to the right or left side, set the vertical
flap located behind the horizontal flap to the desired direction.
Setup of air direction and swinging
1H series: Refer to the description of “2-way Air Discharge Cassette
Type”.
2H series: Refer to the description of“Under CeilingType, 1-way Air
Discharge CassetteType (2SH Series)”.

14
Floor Standing CabinetType
[In Cooling operation]
In cooling operation, set the air outlet flap with a horizontal
set point so that the cold air diffuses the whole room.
[In Heating operation (For Heat-pump model only)]
In heating operation, set the air outlet flap with a downwards
set point so that the hot air blows towards the floor.
How to change the air outlet port
Change the air outlet port using the following procedure.
1 Remove the two fixing screws on the air outlet
port. (The fixing screws are reused.)
2 Remove the discharge port, by pushing up on
the rear side, to a point where you can remove it
from the rear clip.
3 Lift the air outlet port upwards and remove it.
4 Reverse the air outlet port and attach it to the
main unit.
Pay attention so that four claw hooks (two at rear and two
at the lower sides) are hooked on the mounting position.
5 Be sure to tighten the air outlet port with the
removed fixing screws so that the air outlet port
does not come off.

15
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
1, 2 3
1
2
In this case, do not use the
swing function.
Unit No. 1-1No display Unit No. 1-2
Unit No. 1-4 Unit No. 1-3
Floor StandingType
Adjustment of air flow direction upwards/downwards
[In Cooling operation]
In cooling operation, move the flap with your hands so that the horizontal
air outlet points in a direction so that the cold air diffuses the entire room.
[In Heating operation (For Heat-pump model only)]
In heating operation, move the flap with your hands so that the horizontal
air outlet points in a downward direction, towards the floor.
Adjustment of air flow direction rightwards/leftwards
[In case of using unsymmetrical air directions]
Lift up the vertical flap lightly and direct it towards the desired
direction. Once completed lower the flap back down.
In this case, do not use the Swing function.
[In case of automatic swing]
1 Push the
SWING/FIX
button during operation.
•[SWING ] is displayed and the air direc-
tion will automatically change rightwards/
leftwards.
In cases where one remote controller con-
trols multiple indoor units, it is possible to
set each indoor unit individually, so that the
air flow direction can be altered.
2 Push the
SWING/FIX
button again while the
vertical flap is moving will allow you to
stop the louver in the desired position.
3 Swing button
UNIT
•To set up the air flow direction individually,
push the
UNIT
button to display each indoor
unit No.in a group control.Then set up the
air flow direction to the desired indoor unit.
•If there is no display, all the indoor units can
be operated collectively.
•Every push of the
UNIT
button, will change
the display as shown in the figure.
INFORMATION
•If cooling operation is performed with downward air outlet, dew may form on the surface of the cabinet or
the horizontal flap, resulting in possible dripping of water.
•If heating operation is performed with the horizontal air outlet actively moving, unevenness of the tem-
perature may increase in the room.
•Do not move the flap directly with your hands during swing operation; otherwise a fault may be caused.
The vertical flap does not stop immediately even if the
SWING/FIX
button is pushed.To adjust the stop posi-
tion, push the
SWING/FIX
button.

16
4
3
2
1
ON / OFF
FAN
TEMP.
SWING/FIXTIME
MODE
VENT
UNITSET CL
FILTER
RESET
TEST
TIMER SET
OFF
(OFF timer) (Repeat OFF timer)
No display
(ON timer)
OFF ON
TIMER OPERATION
A type of timer operation can be selected from the following three types.
OFF timer :The operation stops when the time on the timer has reached the set time.
Repeat OFF timer :The unit will stop, every time the set time period has elapsed.
ON timer :The unit will start when the time on the timer has reached the set time.
Timer operation
1 Push the TIMER SET button.
•The timer display (type) changes for every
push of the button.
•SET DATA and timer time displays flash.
2 Push the
TIME
buttons to select the “SET TIME”.
For every push of the button, the set time increases in the unit of 0.5 hr (30 minutes).
The maximum set time is 72.0 hr.
For every push of the button, the set time decreases in the unit of 0.5 hr (30 minutes).
The minimum set time is 0.5 hr.
3 Push the SET button.
•
SETTING
display disappears and timer time display goes on.
When the ON timer is activated, the chosen time period will be displayed. Once the time has been
reached, all displays except the ON light will disappear.
Cancel of timer operation
4 Push the CL button.
•TIMER display will disappear.
NOTICE
•When the unit stops after the timer reached the preset time, the Repeat OFF timer will resume the
operation. However by pushing the
ON / OFF
button the repeat function will stop once the time on the
timer has again reached its set time.

17
INSTALLATION
Installation location
WARNING
•Select a location for installation that will be able to safely support the weight of the unit.
If the installation location is not strong enough to support the unit and the unit falls, injury could result.
CAUTION
•Do not install the unit in a location where combustible gases could conceivably leak.
Leaking gases that accumulate in the vicinity of the unit could be ignited by the unit.
REQUIREMENT
•A location that permits the level installation of the unit
•A location that provides enough space to service the unit safely
•A location where water draining from the unit will not pose a problem
Avoid the following types of locations :
•Locations where salt is present in large amounts (seaside areas), or where sulfuric gases are present in
large amounts (hot springs areas)
(If the unit is to be used in such areas, special maintenance is necessary.)
•Locations that generate oils (including machine oils), steam, oily smoke, or corrosive gases
•Locations where organic solvents are used
•Locations in the vicinity of equipment that generates high frequency signals
•Locations where the outdoor unit will blow in the direction of a neighbor's window
•Locations where the noise of the outdoor unit will pose a problem
•Locations with poor air circulation
Electric wiring
WARNING
Ensure that the unit is correctly earthed.
Grounding is necessary. If earthing is incomplete, an electric shock may be caused.
CAUTION
Check that the circuit breaker is fitted.
Attaching a earth leakage breaker is necessary. Otherwise, an electric shock may be caused.
Make sure that the correct capacity fuses are used.
Using wire or copper wire may cause a fire or unit fault.
Ensure that the power supply to the unit is exclusive and is the correct rated voltage.
To disconnect the appliance from the main power supply.
This appliance must be connected to the main power supply by means a circuit breaker or a switch with a
contact separation of at least 3mm.