Toshiba Camileo BW10 User manual

English/Español
CAMILEO®BW10
Quick Start Guide

2
Introduction
For more detailed information please refer to the User's Guide on the
included CD.
Safety instructions
1Do not drop, puncture or disassemble the camcorder; otherwise the
warranty will be voided.
2Do not expose the camcorder to high temperature or leave it in direct
sunlight. Doing so may damage the camcorder.
3Use the camcorder with care. Avoid pressing hard on the camcorder
body.
4For your own safety, avoid using the camcorder when there is a storm
or lightning.
5Do not use batteries of different specifications. Doing so may lead to
the potential for serious damage.
6Remove the battery during long periods between usages, as a
deteriorated battery may affect the functionality of the camcorder.
7Remove the battery if it shows signs of leaking or distortion.
8Use only the accessories supplied by the manufacturer.
9Keep the camcorder out of the reach of infants.
10 Risk of explosion if battery is replaced by an incorrect type.
11 Dispose of used batteries according to the instructions.
About the battery
❖Only use batteries recommended by TOSHIBA as replacements. The
battery is a lithium ion battery, which can explode if not replaced,
used, handled or disposed of properly. Dispose of the battery as
required by local ordinances or regulations.
❖Only charge the battery in ambient temperatures between 41 and 95
degrees Fahrenheit (5 and 35 and degrees Celsius). Otherwise, the
electrolyte solution might leak, battery performance might
deteriorate and the battery life might be shortened.

Waterproof* feature 3
❖Never install or remove the battery without first turning off the power
and disconnecting the USB cable.
❖Only use the supplied USB cable or a generic standard USB AC
adaptor (not supplied by Toshiba). Never attempt to charge the
battery with anything other than the above chargers specified.
Waterproof* feature
This camcorder complies with Japanese Industrial Standards (JIS)
IPX8 (formerly JIS protection grade 8) waterproof standard and can
be used in water. Note, however, that failing to heed the following
precautions may result in damage or injury that is not covered by the
warranty. Please take the time to carefully read and heed the
following cautions.
*Can be submerged up to a maximum depth of 6.56 ft. (2.0m), for up to 60
minutes.
Before using the camcorder
❖When closing the slot cover and port cover, make sure that no
foreign object such as sand, hair, dust, etc. is caught in the
rubber seal.
❖Make sure that the slot cover and port cover are completely and
securely closed to prevent water from getting inside the
camcorder and damaging it.
❖Please note that the camcorder accessories are not waterproof.

Waterproof* feature
4
Cautions concerning use in water
❖The waterproof properties of the camcorder apply to fresh water
and saltwater only; they do not apply to cleaning substances,
chemicals or water from spas, etc. In case of a splash,
immediately wipe off any moisture.
❖Do not immerse in water at a depth greater than 6.56 ft. (2.0m).
❖Do not subject the camcorder to high-pressure water.
❖Do not immerse in water for longer than 60 minutes. After 60
minutes of use in water, allow it to dry for at least 10 minutes.
❖Do not immerse in water that is warmer that 104 °F
(40 °C).
❖Do not open and close the slot cover or port cover when the
camcorder is wet or while it is immersed in water.
❖Do not open and close the slot cover or port cover with wet
hands.
❖Do not open the slot cover or port cover on the beach or at the
pool side.
❖Do not jolt the camcorder while it is immersed in water. Doing so
may cause the slot cover or port cover to open.

Waterproof* feature 5
Storing and maintaining your camcorder
❖Do not leave the camcorder unwashed after it has been immersed
in salt water or if salt water is adhering to it. Doing so may cause
corrosion and discoloration of the plating, as well as
deterioration of the camcorder’s waterproof capability.
❖After the camcorder has been used in water, use fresh water to
wash it. Never use soap or detergent to clean the camcorder, as
doing so will cause deterioration of the camcorder’s waterproof
capability.
❖After washing the camcorder, take care to completely drain it, and
use a dry cloth to wipe off any drops of water adhering to it.
❖Do not leave the camcorder in an environment colder than 32 °F
(0 °C) or warmer than 104 °F (40 °C), as doing so may cause
deterioration of the camcorder’s waterproof capability.
Other cautions
❖Do not subject the camcorder to severe jolts, as doing so may
deform the slot cover, port cover or the camcorder body, thus
compromising its waterproof capability.
What is “JIS IPX8” (formerly “JIS protection
grade 8”)?
❖“JIS IPX8” specifies that a device is protected against the effects
of continuous immersion in water for a limited period of time.

Waterproof* feature
6
Before recording in water
Make sure that the slot cover and the port cover are closed. If a cover is
open, water will get inside the camcorder and damage it. When closing the
slot cover and port cover, make sure that no foreign object such as sand,
hair, dust, etc. is caught in the rubber seal.
There are places in the camcorder where water might accumulate, but
this will not affect its waterproof properties. To care for your camcorder
after using it in water, please refer to the User's Manual on the supplied
DVD-ROM.
Regulatory Information
TOSHIBA declares that this product conforms to the following Standards:
CE compliance
This product is CE marked in accordance with the requirements of the
applicable EU Directives. Responsible for CE marking is Toshiba Europe
GmbH, Hammfelddamm 8, 41460 Neuss, Germany. A copy of the official
Declaration of Conformity can be obtained from following website:
http://epps.toshiba-teg.com.
Model number: CAMILEO®BW10
FCC Conditions
This equipment has been tested and found to comply with Part
15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.

Waterproof* feature 7
Contact
Additional Information
© Copyright 2011 TOSHIBA CORPORATION. All rights reserved.
TOSHIBA reserves the right to make technical changes. TOSHIBA
assumes no liability for damages incurred directly or indirectly from
errors, omissions or discrepancies between this product and the
documentation.
Trademarks
CAMILEO is a registered trademark of Toshiba America Information
Systems, Inc. and/or Toshiba Corporation.
Adobe and Photoshop are either registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and/or other countries.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
Secure Digital and SD are trademarks of SD Card Association.
YouTube and the YouTube logo are registered trademarks of Google, Inc.
All other brand and product names are trademarks or registered
trademarks of their respective companies.
Address: TOSHIBA America Information Systems, Inc.
9740 Irvine Boulevard
Irvine, California 92618-1697
Telephone: [phone]

Getting Started
8
Getting Started
Loading the battery
Before using the camcorder, remove the protective film from the
battery as shown below.
(Sample Illustration) Removing the protective film from the
battery
Inserting the battery
To install the supplied battery:
1While pressing down on the slot cover release latch, slide the
slot cover out and open.
(Sample Illustration) Opening the battery/media card slot cover

Getting Started 9
2Insert the battery until it locks into place.
(Sample Illustration) Inserting the battery
3Close the battery/media card slot cover. Secure it by sliding it
back into place.
(Sample Illustration) Closing the battery/media card slot cover
Close the slot cover and port cover securely.
If any cover is not closed or is not closed completely, the
camcorder will no longer be waterproof. When closing a cover,
make sure that no foreign object such as sand, hair, dust, etc.
is caught in the rubber seal.

Inserting and removing a media card
10
Inserting and removing a media card
Your camcorder comes with internal memory that allows you to
store photos and videos. The images you capture are saved to the
camcorder’s internal memory.
You can expand the memory capacity by using an optional media
card. The Media card reader supports the use of Secure Digital™
(SD™), SDHC™ (High Capacity), and SDXC™ (Extended
Capacity) Memory Cards. When a card is installed, images are
recorded to and played back from the card.
An SD™ Card must be purchased separately.
To install a media card:
1While pressing down on the slot cover release latch, slide the
slot cover out and open.
2Insert a memory card into the slot until it locks into place as
shown below.
(Sample Illustration) Inserting the media card