Toshiba V Series User manual

6F8C1130
  

Important Information
No patent liability is assumed by TOSHIBA Corporation with respect to use of information, illustrations,
circuits, equipment or examples of application in this publication.
TOSHIBA Corporation reserves the right to make changes and improvements to this publication and/or
related products at any time without notice. No obligation shall be incurred other than as noted in this
publication.
This publication is copyrighted and contains proprietary material. No part of this book may be reproduced,
stored in a retrieval system, or transmitted, in any form or by any means — electrical, mechanical,
photocopying, recording, or otherwise — without obtaining prior written permission from TOSHIBA
Corporation.
Microsoft, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation in the
U.S.A. and other countries.
©TOSHIBA CORPORATION 2004-2005. All rights reserved.

6F8C1130
i
Safety Precautions
This manual contains important information for the operator to operate this product safely and
correctly and avoid bodily injury and property damage.
Grasp the meanings of the following marks and their descriptions before reading this manual.
Hazard Classifications
WARNING
Indicates a potentially hazardous situation which, if not avoided, could
result in serious injury or death.
CAUTION
Indicates a potentially hazardous situation which, if not a avoided, can
result in minor or moderate injury, or property damage. It can also be
used to alert against unsafe practices.
note: 1. Serious injury means loss of sight, injury, burns (high temperature, low temperature),
electrical shock, fracture, or intoxication which leaves aftereffects or requires hospitalization
or need to go to the hospital for a long time.
2. Injury means hurt, burn, or electrical shock which does not require hospitalization or going to
the hospital for a long time.
3. Property damage means extended breakdown of assets and materials.
Notation of Markings
Prohibited
Indicates a "may not" mark.
The concrete forbiddance is indicated with a pictograph or wording.
Mandatory
Indicate a mandatory action that you should never fail to do.
The concrete content is indicated inside or near the circle with a
pictograph or wording.
Caution
Indicates a caution.
The concrete content is indicated inside or near the triangle.
note: 1. The description of forbiddance, mandatory, and caution marks are subject to change,
depending on the labels on the main unit.

ii
Remote Engineering Package
1. Checking the Warning Labels on the Main Unit
Make sure warning markings are attached on the main unit.
If any of them are missing or the wording is illegible, contact Toshiba's Service Department.
2. Precaution on Installation
WARNING
CAUTION
Avoid the following locations when installing or
storaging the equipment.
• Locations where there is dust, salinity, or ion
particles
• Locations where there are corrosive gases
(SO2, H2S) or flammable gases
• Locations where vibration or shock occurs
beyond the allowance
• Locations where there is condensation due
to sharp temperature variations
• Locations where the ambient temperature
exceeds the allowance range
• Locations where the relative humidity
exceeds the allowance range
• Locations where the equipment is exposed
to direct sunlight
• Locations where strong electric radiation or
magnetic field is generated
Improper the installation or writing of the
system can cause not only insufficient
performance but also malfunction and failure
of the equipment
Be sure to ground the equipment.
Operation without grounding may cause
accidental fire or shock.
Mandator
y
Mandator
y
Install the equipment at a place where
maintenance and inspection are easy to do.
Otherwise, recovery from failure may take
much more time, leading to a serious
accidents.
Mandator
y
Mandator
y

6F8C1130
iii
3. Safety Precautions on Maintenance and inspection
WARNING
CAUTION
Do not cover the hole of the equipment, and
the ventilator/air inlet of the system.
Otherwise, overheating, etc. can cause fire or
malfunction.
Forbidden
Turn off power removing or connecting any
modules, boards, or devices.
Otherwise, it can cause electrical shock, or
machine damage.
Mandator
y
Turn off power removing any modules after
installing.
Otherwise, exposed conductive parts of wire
or on the rear of terminal blocks can cause
electrical shock.
Mandator
y
Place any modules or boards removed from
the unit on a conductive mat or conductive
bag (containing a spare board, etc.) on an
grounded desk.
Otherwise, static electricity can damage
components of the module.
Mandator
y
Touch a grounded metal part to discharge the
static electricity on your body before touching
the equipment.
Otherwise, charged static electricity on your
body can cause malfunction or failure.
Mandator
y
Be careful not to hit or fall off the equipment
by accident.
Excess shock can cause failure.
Forbidden

iv
Remote Engineering Package
4. Precautions During Parts Replacement
WARNING
5. Precautions During Daily Use
WARNING
Do not apply benzene and thinner when
cleaning the equipment.
Otherwise, it can cause deformity or
discoloration the panel or case of the
equipment.
Forbidden
Use soft cloth to clean the equipment.
Use water-dipped and squeezed cloth to clean
it if dirty.
Leaving the equipment dirty can cause
mistaken or malfunction.
Mandator
y
Turn off power of the equipment before
replacing the power fuse or warning fuse.
Otherwise, it can cause electrical shock or fire.
Mandator
y
Apply power of the specified ratings (voltage
fluctuation range, frequency, output rating,
etc.) in User's manual.
Otherwise, it can cause malfunction, machine
damage or fire due to overheat.
Mandator
y
Turn off power immediately if the ambient
temperature or internal temperature exceeds
beyond normal range or if failure is occurred in
the equipment.
Contact Toshiba for repairing.
Operation under such situation can cause fire
or electrical shock.
Mandator
y

6F8C1130
v
CAUTION
6. Safety Precautions on Disposal
WARNING CAUTION
Do not touch any components, terminals,
connectors, or printed circuit boards in the
module.
Otherwise, it can cause the IC or LSI or the
like to be broken by static electricity, resulting
in failure or malfunction.
Also, the edge of components can cause
injury.
Forbidden
Do not forcibly bend or pull or distort the
power cord and other cables. Otherwise, they
can be cut off or cause overheat.
Forbidden
Do not disassemble or modify the equipment.
Otherwise, it can cause malfunction or failure.
Forbidden
Do not enter wire scrapes or other foreign
debris into the equipment.
Also, do not insert metal parts into them.
They can cause fire or accidents.
Forbidden
Do not throw lithium batteries into fire.
Otherwise, they can explode.
Forbidden
Observe local regulations for disposal of the
lithium batteries or the product (Base unit and
modules).
Mandator
y

vi
Remote Engineering Package
Limitation of Applications
The equipment has been designed and manufactured for use in an industrial environment.
However, the equipment is not intended to be used for systems which can endanger human life (Note
1).
Consult Toshiba if you intend to use the equipment for a special application which involves human life
and has great influence on the maintenance of the public function (Note 2). This is why such
application requires special care on the operation, maintenance, and control of the system (Note 3).
(Note 1) The systems which can endanger human life are life maintenance systems, equipment
installed in the surgery, and other medical equipment.
(Note 2) The systems which involve human life and have great influence on the maintenance of the
public function mean the main control system of a nuclear power plant, safety and protection
system of a nuclear power facility, transport operation and control systems for mass
transportation, control systems of aviation and space systems, and other systems and
subsystems where safety is critical.
(Note 3) "Special care" means to build a safety system (foolproof design, fail safe design, redundancy
design, etc.) in full consultation with Toshiba's engineers.
Immunity
Toshiba is not liable for any loss caused by fire, earthquake, action by a third party, or other accidents,
or the operator's intentional or accidental misuse, incorrect use, or use under abnormal condition.
Toshiba is not liable for any incidental loss caused by the use or non-use of this product, such as loss
of business profits, suspension of business, or loss or change of data on memory.
Toshiba is not liable for the loss caused by an operation contradictory to any of the instructions stated
in this manual.
Toshiba is not liable for the loss caused by an incorrect operation in combination with other equipment.
Toshiba is not liable for the loss caused by a malfunction in combination with an application program
made by the customer.
NOTE:
Use cellular phones and PHSs at least one meter away from the working equipment, transmission
cables, and I/O bus cable. Otherwise, the system can malfunction.

6F8C1130 vii
Preface
This document is the user's manual for Remote Engineering Package of Integrated
Controller V series.
Without customization of the existing network infrastructure, this product will realize the
remote maintenance and engineering of V series via not only Intranet but also Internet.
Generally, to realize the remote maintenance and engineering of process controllers, most
of other remote control software products need to change some networking settings, for
instance, opening some special ports of user’s firewall. So they limits users to using the
software in Intranet or special VPN networks.
This product will solve the problems and limitations. Because this products can connect the
private PC on user’s private network with the remote PC on Internet over the user’s firewall,
using only HTTP and HTTPS protocols.
This product is independent of V-Tool, that is the engineering tool of V series. So it can be
used to not only remote control V-Tool, but also any other applications, for instance,
SCADA, maintenance tools on user’s PC.
Product name Product code
Remote Engineering Package [English/Japanese] GET9RB1SS
[Software of this Package]
(1) MAN-PC software : executed on the remote controlled PC.
(2) REM-PC software : executed on the remote operation PC.
[Software license]
One license allows the user to use one MAN-PC and one REM-PC.
[License authorization]
Set the 32 characters license-key to both PCs at only the first time to start.
The key is printed on the enveloped sheet of the package.
Each time to start, the license authorization is done automatically, connecting with
TOSHIBA server via Internet. So both MAN-PC and REM-PC need to be on the network
which can be connected with Internet.

Preface
Remote Engineering Package
viii
The contents of this document are shown as follows:
Chapter 1. Requirements for Remote Engineering
1.1 Requirements for Network Configuration
1.2 Requirements for Hardware and Software
Chapter 2. How to Install/uninstall Remote Engineering Package
2.1 How to install
2.2 Setting for license authorization
2.3 How to uninstall
Chapter 3. How to use Remote Engineering Package
3.1 Operation steps
3.2 Step1:Preparation
3.3 Step2:Staring REM-PC
3.4 Step3:Starting Server of REM-PC
3.5 Step4:Starting MAN-PC
3.6 Step5:Connecting MAN-PC to REM-PC
3.7 Step6:Starting Windows Remote Desktop
3.8 Step7:Operating Windows Remote Desktop
3.9 Step8:Closing Windows Remote Desktop
3.10 Step9:Closing MAN-PC
3.11 Step10:Closing REM-PC
3.12 Other operations
Chapter 4. Messages of Remote Engineering Package
4.1 Error messages of MAN-PC
4.2 Error messages of REM-PC
4.3 Messages of Windows Remote Desktop.
Chapter 5. Trouble Shooting of Remote Engineering Package