Toshiba XDE600KU User manual

Upconverting 1080p
Extended Detail DVD Player
XDE600KU
DIGITAL VIDEO
2
11
16
19
30
36
Introduction
Connections
Basic playback
Advanced playback
Function setup
Others
© 2009 Toshiba Corporation
Owner’s Record
The model number and serial number are on the back of
your DVD Player. Record these numbers in the spaces
below.Refertothesenumberswhenever youcommunicate
with yourToshiba dealer about this DVD Player.
Model number:
Serial number:
OWNER’S MANUAL
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

2
Introduction
SAFETY PRECAUTIONS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSETHIS APPLIANCETO RAIN OR
MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN
THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TOWIDE SLOT OF AC POWER OUTLET,
THEN FULLY INSERT.
WARNING: The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquid, such as vases,
shall be placed on the apparatus.
CAUTION: This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference.
Should the unit require maintenance, contact an authorized service location.
Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure.
Visible and invisible laser radiation when open and interlocks defeated.
DO NOT STARE INTO BEAM.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by Toshiba, or parties authorized by Toshiba,
could void the user’s authority to operate the equipment.
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in this
owner’s manual.
CLASS 1
LASER PRODUCT
Warnings: • The main plug is used as disconnect device and it should remain readily operable during intended used. In
order to disconnect the apparatus from the mains completely, the main plug should be disconnected from
the mains socket outlet completely.
• Minimum 10 cm (4 inches) distances around the apparatus for sufficient ventilations.
• The ventilation should not be impeded by covering the ventilation openings with items such as newspaper,
table-cloths, curtains, etc.
• No naked flame sources such as lighted candles should be placed on the apparatus.
• The use of apparatus in moderate climates.
The symbol for Class (Double lnsulation)
CAUTION: VISIBLE LASER RADIATION WHEN
OPEN. DO NOT STARE INTO BEAM.
AVIS
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

3
Introduction
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third grounding prong.The wide blade or the third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Portable Cart Warning
15. Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or electric
shock.
16. Never expose the apparatus to dripping or splashing or place items such as vases, aquariums, any other item filled with
liquid, or candles on top of the unit.
17. Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.
18. Do not place anything on top of this unit.
19. Do not place the apparatus on amplifiers or equipment that may produce heat.
20. Never block or cover the slots or openings in the unit.
Never place the unit:
• on a bed, sofa, rug or similar surface;
• too close to drapes, curtains, or walls; or
• in a confined space such as a bookcase, built-in cabinet, or any other place with poor ventilation.
The slots and openings are provided to protect the unit from overheating and to help maintain reliable operation.
21. Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and
apparatus malfunction.
22. If the apparatus should emit smoke or an unusual odor, immediately disconnect the power cord from the wall outlet. Wait
until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause fire.
23. During thunderstorms, do not touch the connecting cables or the apparatus.
24. Warning: To prevent spread of fire, keep candles or other open flames away from this product at all times.
ADDITIONAL SAFETY INSTRUCTIONS
Location of the required label
The rating plate and the safety caution
are on the rear of the unit.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

4
Introduction
Precautions
Notes on moisture condensation
Moisture condensation damages the DVD player.
Please read the following carefully.
Moisture condensation occurs, for example, when you pour
a cold drink into a glass on a warm day. Drops of water form
on the outside of the glass. In the same way, moisture may
condense on the optical pick-up lens inside this unit, one
of the most crucial internal parts of the DVD player.
Moisture condensation occurs during the following
cases.
When you bring the DVD player directly from a cold
place to a warm place.
When you use the DVD player in a room where you just
turned on the heater, or a place where the cold wind
from the air conditioner directly hits the unit.
In summer, when you use the DVD player in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD player in a humid place.
Do not use the DVD player when moisture
condensation may occur.
If you use the DVD player in such a situation, it may
damage discs and internal parts. Remove the disc,
connect the power cord of the DVD player to the wall
outlet, turn on the DVD player, and leave it for two or
three hours. After two or three hours, the DVD player will
have warmed up and evaporated any moisture.Keep the
DVD player connected to the wall outlet and moisture
condensation will seldom occur.
Notes on handling
When shipping the DVD player, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was originally
packed at the factory. Take care not to give it a shock or
shake when carrying.
Do not use volatile liquids, such as insect spray, near
the DVD player. Do not leave rubber or plastic products
in contact with the DVD player for a long time. They will
leave marks on the finish.
The top and rear panels of the DVD player may
become warm after a long period of use. This is not a
malfunction.
When the DVD player is not in use, be sure to remove
the disc and turn off the power.
If you do not use the DVD player for a long period, the
unit may not function properly in the future.Turn on and
use the DVD player occasionally.
Notes on locating
Place the DVD player on a level surface. Do not use it on
a shaky or unstable surface such as a wobbling table or
inclined stand.The loaded disc may come off the proper
position and cause damage to the DVD player.
When you place this DVD player near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD
player away from the TV, radio, or VCR.
Notes on cleaning
Use a soft, dry cloth for cleaning.
For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe it
dry.
Do not use any type of solvent, such as thinners and
benzene, as they may damage the surface of the DVD
player.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.
Inspection and Maintenance
This DVD player is a high technology, precision device.
If the optical pick-up lens and disc drive parts become
dirty or worn down, the picture quality may be reduced.
To avoid reduction in picture quality, it is recommended
that regular inspection and maintenance (cleaning or
parts replacement) be performed every 1,000 hours of
use. For further details, contact your nearest consumer
electronics dealer.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

5
Introduction
Notes on Discs
Playback side
DVD
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Structure of disc contents
Normally, DVDs are divided into titles, and the titles are
sub-divided into chapters.VIDEO CDs and audio CDs are
divided into tracks.
DVD
VIDEO CD/audio CD
Each title, chapter or track is assigned a number, which is
called “title number”, “chapter number” or “track number”
respectively.
There may be discs that do not have these numbers.
On handling discs
Do not touch the playback side of the disc.
Do not attach paper or tape to discs.
On cleaning discs
Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc clean.
If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner, benzine,
commercially available cleaners or antistatic spray for
vinyl LPs. It may damage the disc.
Track 1 Track 2 Track 3 Track 4 Track 5
VIDEO CD/audio CD
Mpeg-4 Visual and Mpeg layer 3
THIS PRODUCT IS LICENSED UNDER THE MPEG-4
VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A
CONSUMER FOR ()ENCODING VIDEO IN COMPLIANCE
WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4
VIDEO”) AND/OR ()DECODING MPEG-4 VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION
INCLUDING THAT RELATING TO PROMOTIONAL,
INTERNAL AND COMMERCIAL USES AND LICENSING
MAY BE OBTAINED FROM MPEG LA,L.L.C. SEE HTTP://
WWW.MPEGLA.COM
MPEG Layer-3 audio coding technology licensed from
Fraunhofer LLS and Thomson.
Notes on patent portfolio license
On storing discs
Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.
Notes on copyright
The unauthorized recording, use, distribution, or revision
of copyrighted materials including, without limitation,
television programs, videotapes, and DVDs, is prohibited
under the Copyright Laws of the United States and other
countries, and may subject you to civil and criminal
liability.
This product incorporates copyright protection technology
that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized
by Macrovision Corporation, and is intended for home and
other limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

6
Introduction
DIGITAL VIDEO
SUPER VIDEO
• You cannot play discs other than those listed above.
• You cannot play DVD-RAM discs or non-standardized discs,
etc., even if they may be labeled as above.
• This DVD player uses the NTSC color system, and cannot
play DVDs recorded in any other color system (PAL, SECAM,
etc.).
Because of problems and errors that can occur during the
creation of DVD and CD software and/or the manufacture
of DVD and CD discs, Toshiba cannot assure that this DVD
player will successfully play every disc bearing the DVD and
CD logos. If you happen to experience any difficulty playing
a DVD and/or CD disc on this DVD player, please contact
Toshiba Customer Service.
is a trademark of DVD Format/Logo Licensing
Corporation.
Notes on Discs (continued)
DVDs
Disc Mark
Contents
Disc
Size
Maximum
playback time
VIDEO
CDs
Approx. 4 hours
(single sided disc)
Approx. 8 hours
(double sided disc)
Approx. 80 minutes
(single sided disc)
Approx. 160 minutes
(double sided disc)
Approx. 74 minutes
Approx. 20 minutes
8 cm
12 cm
8 cm
12 cm
Audio
+
video
(moving
pictures)
Audio
+
video
(moving
pictures)
Audio
CDs
Approx. 74 minutes
Approx. 20 minutes
8 cm
(CD
single)
12 cm
Audio
The following discs are also available.
DVD±R/±RW and DVD-ROM discs of DVD format
CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA or
JPEG format
Official DivX® Certified product
Plays all versions of DivX® video (including DivX® 6)
with standard playback of DivX® media files
Some of these discs may be incompatible.
SUPER
VIDEO
CDs
DivX®
35 min.
10 min.
8 cm
12 cm
Audio
+
video
(moving
pictures)
Audio
+
video
(moving
pictures)
It depends on DivX®
quality
8 cm
12 cm
About this owner’s manual
This owner’s manual explains the basic instructions of
this DVD player. Some DVDs are produced in a manner
that allows specific or limited operation during playback.
As such, the DVD player may not respond to all operating
commands. This is not a defect in the DVD player. Refer
to instruction notes of discs.
“ ” may appear on the TV screen during operation.
A “ ” means that the operation is not permitted by the
DVD player or the disc.
Notes on region numbers
The region number of this DVD player is 1. If region
numbers, which stand for their playable area, are printed
on your DVD and you do not find or , disc playback
will not be allowed by the player. (In this case, the DVD
player will display a message on-screen).
On VIDEO CDs
This DVD player supports VIDEO CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback variations
depending on types of discs.
• VIDEO CD not equipped with PBC function (Version
1.1)
Sound and movie can be played on this DVD player in
the same way as an audio CD.
• VIDEO CD equipped with PBC function (Version
2.0)
In addition to operation of a VIDEO CD not equipped with
the PBC function, you can enjoy playback of interactive
software with search function by using the menu
displayed on the TV screen (Menu Playback). Some of
the functions described in this owner’s manual may not
work with some discs.
Playable discs
This DVD player can play the following discs.
About
The
icons on the heading bar show the
playable discs for the function described under that heading.
DVD
: You can use this function with DVD discs.
: You can use this function with Video CDs.
CD
: You can use this function with Audio CDs/CD-R/RW
CDs.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

7
Introduction
Table of Contents
Introduction
SAFETY PRECAUTIONS ........................... 2
IMPORTANT SAFETY INSTRUCTIONS .... 3
Precautions ............................................... 4
Notes on Discs .......................................... 5
Notes on region numbers ................................... 6
Table of Contents ...................................... 7
Identification of Controls ......................... 8
Front panel...........................................................8
Rear panel ...........................................................8
DVD display ........................................................8
Remote control ....................................................9
Loading batteries ...............................................10
Operating with the remote control......................10
Connections
Connecting to a TV ................................... 11
Connecting to a TV ............................................ 11
Connecting to a TV (Using the component video
jacks).................................................................. 11
Connecting to a display (Using a HDMITM cable) .......12
Connecting to Optional Equipment ........13
Connecting to an amplifier equipped with a
Dolby®Digital decoder .................................... 14
Connecting to an amplifier equipped with
Dolby Surround Pro Logic................................ 14
Connecting to an amplifier equipped with a
DTS®decoder ................................................... 15
Connecting to an amplifier equipped with an
MPEG2 audio decoder ..................................... 15
Connecting to an amplifier equipped with a
digital audio input.............................................. 15
Basic playback
Playing a Disc........................................... 16
Basic playback .................................................. 16
Variable Speed Playback ......................... 17
Playing in fast reverse or fast forward
directions .......................................................... 17
Playing frame by frame ..................................... 17
Playing in slow-motion ...................................... 17
Resuming playback from the same location ..... 17
Locating a Desired Section..................... 18
Locating a title using the top menu ....................18
Locating a specific chapter or track .................. 18
Advanced playback
Accessing a Specific Location Directly ....... 19
Locating a specific title/chapter/time...................19
Repeating a Specific Segment.................. 20
Repeating a specific segment.............................20
Playing in a Varied Order ..........................20
Playing titles, chapters or tracks in a varied
order ...................................................................20
Playing in a Favorite Order ....................... 21
Setting titles, chapters or tracks in a favorite
order ...................................................................21
Zooming a Picture...................................... 22
Zooming a picture ...............................................22
Selecting the Sound Enhancement
(E.A.M.)........................................................ 22
Selecting the sound enhancement .....................22
Selecting the Picture Mode ....................... 23
Selecting the picture mode .................................23
Selecting Subtitles..................................... 23
Selecting a subtitle language..............................23
Selecting the Camera Angle .....................24
Changing the camera angle................................24
Selecting a Language ................................ 24
Selecting a playback audio setting......................24
On-screen Display Operation ...................25
On-screen display operation ...............................25
Playing MP3/WMA Files............................. 26
Playing MP3/WMA files.......................................26
Viewing JPEG Files.................................... 27
Viewing JPEG files..............................................27
Viewing a thumbnail view....................................27
Playing DivX®, MPEG-4 Files.................... 28
Playing DivX®, MPEG-4 files..............................28
Playing USB Device ................................... 29
Connecting to USB flash drive............................29
Function setup
Customizing the Function Settings.......... 30
Setting procedure ...............................................30
Setting details .....................................................30
Others
Table of Languages.................................... 36
Before Calling Service Personnel............. 37
Specifications............................................. 38
Limited Warranty ........................................ 39
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

8
Introduction
Identification of Controls
See the page in for details.
16
29
16
10
16
8
12
HDMI indicator
16
PAUSE button
16
16
USB jack
Front panel
12
HDMI OUT jack
11
11
11
14 15
Power Cord
OPTICAL OUT jack
11
S-VIDEO OUT jack
14 15
Y
VIDEO
P B P R
HDMI OUT ANALOG
COAXIAL DIGITAL
RL
VIDEO OUT
AUDIO
OUT
OPTICAL OUT
S-VIDEO OUT
Rear panel
The indicators vary depending on the kinds of discs you play.
• During playback:
Example
• During playback:
Example
• During playback:
Example
Some discs may only
display chapter numbers.
Some discs may only
display track numbers.
Some discs may only
display track numbers.
DVD display
Chapter/Track
number Indicator
Multifunctional indicator
(indicates operating status
or messages, etc.)
• During thumbnail
viewing
No disc Bad disc OPEN LOAD/CLOSE Power off
DVD VIDEO VIDEO CD Audio CD Picture
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

9
Introduction
*MENU button
Use the MENU button to display the menu included on
many DVDs.To operate a menu, follow the instructions
in “Locating a title using the top menu.”
18
*RETURN button
Return to menu display for VCD (2.0) discs with
menu.
16
USB button
19
22
23
24
17
18
17
18
18
20
19
21
30
29
16
19
17
23
24
16
16
18
17
18
25
16
25
16
16
20
22
29
PIC MODE button
T / SEARCH button
USB
DVD
DVD button
Remote control
The instructions in this manual describe the functions on the remote control. See the page in for details.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

10
Introduction
Open the cover.
Insert batteries (R03/AAA size).
Make sure to match the + and – on the batteries to
the marks inside the battery compartment.
Caution
• Never throw batteries into a fire.
Notes
• Be sure to use R03/AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of
battery disposal.
• Do not mix different battery types or combine used batteries
with new ones.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace both batteries
with new ones.
• If the batteries are dead or if you will not be using the remote
control for a long time, remove the batteries to prevent battery
acid from leaking into the battery compartment.
Operating with the remote control
Point the remote control at the remote
sensor and press the buttons.
Distance: About 7 m (23 feet) from the front of the
remote sensor
Angle: About 30° in each direction of the front of
the remote sensor
* Do not expose the remote sensor of the DVD player
to a strong light source such as direct sunlight or
other illumination. If you do so, you may not be able
to operate the DVD player via the remote control.
Notes on the remote control
• Direct the remote control at the remote sensor of the DVD
player.
• When using the remote control, press the buttons at
intervals of about 1 second to ensure the correct mode of
operation.
• Do not drop or give the remote control a shock.
• Do not leave the remote control near an extremely hot or
humid place.
• Do not spill water or put anything wet on the remote
control.
• Do not open the remote control.
• If the remote control is not going to be used for a long time,
remove the battery to avoid damage caused by battery
leakage corrosion.
2
Loading batteries
1
CAUTIONS:
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
• Do not dispose of battery in fire; battery may explode or
leak.
• When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal
of these batteries must be strictly followed.
Identification of Controls (continued)
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

11
Connections
Connections
Connecting to a TV
Connect the DVD player to your TV.
Notes
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making
any connections.
• If your television set has one audio input, connect the left and right audio outputs of the DVD player to a Y cable adapter (not supplied)
and then connect to your TV.
• Connect the DVD player directly to your TV. If you connect the DVD player to a VCR, TV/VCR combination or video selector, the playback
picture may be distorted as DVDs are copy protected.
• Analog audio out will not have sound if DTS playback is selected.
Audio/Video cable
(
su
pp
lied
)
S-Video cable (not supplied)
Normal TV
To 2ch AUDIO OUT
(R: red, L: white)
To VIDEO
OUT
(yellow)
To video
input
(yellow)
To audio
input
Y
VIDEO
PBPR
HDMI OUT ANALOG
COAXIAL DIGITAL
RL
VIDEO OUT
AUDIO
OUT
OPTICALOUT
S-VIDEO OUT
If the TV has a S-video input, connect the DVD
player with an S-video cable. When using an
S-video cable, do not connect the yellow video
cable and component video cables (Y/PB/PR).
Connecting to a TV
Connecting to a TV (Using the component video jacks)
To audio input
To 2ch AUDIO OUT
(R: red, L:white)
Y
VIDEO
P B P R
HDMIOUT ANALOG
COAXIALDIGITAL
RL
VIDEO OUT
AUDIO
OUT
To Y video
input
To P video
input
B
To P video
input
R
Audio cable (not supplied)
Com
p
onent video cable
(
not su
pp
lied
)
OPTICALOUT
S-VIDEOOUT
Connections
• Make the following setting.
On-screen display Select: Page
“Off”,
“PCM” or
“Bitstream”
“Digital Output”
“Video out”
Component
S-VIDEO
P-Scan
HDMI
32
33
Interlaced outputs (ColorStream®)
Some TVs or monitors are equipped with component video inputs.
Connecting to these inputs allows you to enjoy higher quality picture
playback.
Actual labels for component video inputs may vary depending on the
TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)
In some TVs or monitors, the color levels of the playback picture may
be reduced slightly or the tint may change. In such a case, adjust the
TV or monitor for optimum performance.
Progressive outputs (ColorStream Pro®)
Some TVs or monitors are equipped with component video inputs
that are capable of reproducing a progressively scanned video signal.
Connecting to these inputs allows you to view the highest quality
pictures with less flicker.
Consumers should note that not all high definition television sets
are fully compatible with this product and may cause artifacts to
be displayed in the picture. In case of 480 progressive scan picture
problems, it is recommended that the user switch the connection to
the “standard definition” output. If there are questions regarding our
TV set compatibility with this model 480p DVD player, please contact
our Customer Service Center.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

12
Connections
About HDMI
HDMI (High Definition Multimedia Interface) supports both video
and audio on a single digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices. HDMI was developed
to provide the technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface (DVI) in one
specification. HDCP is used to protect digital content transmitted
and received by DVI-compliant or HDMI-compliant displays.
HDMI has the capability to support standard, enhanced, or high-
definition video plus standard to multi-channel surround-sound audio.
HDMI features included uncompressed digital video, a bandwidth of
up to 2.2 gigabytes per second (with HDTV) signals, one connector
(instead of several cables and connectors), and communication
between the AV source and AV devices such as DTVs.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI licensing LLC.
Setting the video output signal (interlaced / progressive)
You can setting the video output signal for better picture
quality.
Press the SETUP button on the remote control and select the
Video option, then set the Video out to P-Scan. See
32
.
If your TV does not support the progressive scan format, the
picture will appear scrambled or blank. To return to normal
picture, turn off progressive scan (P-Scan) by setting the Video
out to Component mode.
• Make the following setting.
On-screen display Select:
Page
Notes
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet
before making any connections.
• If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD player away
from the tuner and radio.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level.
Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the speakers
may be damaged.
• Analog audio out will not have sound if DTS playback is selected.
• ColorStream®and ColorStream Pro®are registered trademarks of Toshiba America Cousumer Products L.L.C.
“PCM” or
“Bitstream”
“Digital Output”
Component
*P-Scan
(Progressive)
“Video out”
* Only forTV equipped with component video input
jacks which support the progressive scan.
32
33
480p, 720p, 1080i,1080p and 1080p/24F are signals created with
this DVD Player from original 480i signal. The resolution of the
picture may not be increased even if they are selected.
480p and 720p cannot be selected when the picture mode is
sharp, color or contrast
23
.
• Make the following setting.
On-screen display Select:
Page
“PCM”
“Digital Output”
HDMI
“Video out”
HDMI-compatible display
HDMI Cable
To HDMI
Output
Y
VIDEO
P B P R
HDMI OUT ANALOG
COAXIAL DIGITAL
RL
VIDEO OUT
AUDIO
OUT
(not supplied)
OPTICAL OUT S-VIDEO OUT
Available output signals are below:
• Auto
• 480p (progressive)
• 720p (progressive)
• 1080i (interlaced)
• 1080p (progressive)
• 1080p/24F (progressive)
Setting the video quality (HDMI mode)
The video quality is required to match your TV having HDMI feature
and suitable quality. Please also check your TV owner’s manual.
Set the video quality in HDMI Resolution menu (see
32
) to
change the output signals as below.
If the appropriate video output signal is selected, the HDMI
indicator will lights up.
32
33
Connecting to a display (Using a HDMITM cable)
HDMI indicator Video output signal
illuminates “ • 480p, • 720p,
• 1080i, • 1080p, • 24F ”
Auto
illuminates “ • 480p ” 480p (progressive)
illuminates “ • 720p ” 720p (progressive)
illuminates “ • 1080i ” 1080i (interlaced)
illuminates “ • 1080p ” 1080p (progressive)
illuminates “ • 1080p, • 24F ” 1080p/24F (progressive)
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

13
Connections
Connections
Notes
• If Auto is selected, it follows preference HDMI aspect ratio of TV.
• Refer to the owner’s manual of the connected TV as well.
• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.
• If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using a HDMI cable.
• The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible
with, including DVD-Video, Video CD/Super VCD, CD, WMA, MP3 and DivX®.
• This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) depending on the component
you have connected. Using a HDMI connection may result in unreliable signal transfers.
• Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with
this DVD player.
• When using HDMI cable, do not connect to other analog video outputs.
• No sound will be output from the HDMI cable if the digital out is not set to PCM.
• HDMI output is only available when the Video Out is set to “HDMI”. Otherwise the HDMI button is invalid.
Notes
• DO NOT connect the OPTICAL OUT or COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby
Digital Receiver. This input on your A/V Receiver is reserved for Laser disc use only and is incompatible with the OPTICAL
OUT /COAXIAL DIGITAL AUDIO OUT jack of the DVD player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the “DIGITAL (COAXIAL)” input of a Receiver or
Processor.
• Connect the OPTICAL OUT jack of the DVD player to the “DIGITAL (OPTICAL)” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.
Warnings
• When you are connecting (via the OPTICAL OUT or
COAXIAL DIGITAL AUDIO OUT jack) an AV decoder that
does not have Dolby Digital, Digital Theater Systems (DTS)
or MPEG2 decoding function, be sure to set “Digital Output”
to “PCM” from the on-screen displays.Otherwise, high volume
sound may damage your hearing as well as the speakers.
• When playing DTS-encoded discs (DVDs and audio CDs),
excessive noise may be output from the analog audio output
jacks. To avoid possible damage to the audio system, you
should take proper precautions when the analog audio output
jacks of the DVD player are connected to an amplification
system. To enjoy DTS Digital Surround™ playback, an
external 5.1 channel DTS Digital Surround™ decoder system
must be connected to the OPTICAL OUT or COAXIAL
DIGITAL AUDIO OUT jack of the DVD player.
• For connection to your TV, see “Connecting to a TV” .
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
On-Screen Display Setting Content of output for each output jack
“Video out”
Setting
HDMI Output
Setting
HDMI
Output
Video
Output
Component
Output
S-Video
Output
Component
(Interlaced)
Invalid - Composite 480i -
S-VIDEO Invalid - Composite - S-Video
P-Scan
(Progressive)
Invalid - Composite 480p -
HDMI
480p 480p Composite 480i -
720p 720p Composite 480i -
1080i 1080i Composite 480i -
1080p 1080p Composite 480i -
1080p/24F 1080p/24F Composite 480i -
Content of the output for each output jack is shown in the following table and differ depending on the On-Screen Display
Setting:
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

14
Connections
Dolby Surround Pro Logic
You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting
an amplifier and speaker system (right and left front speakers, a center speaker,
and one or two rear speakers).
With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby®Digital decoder.” Refer to that amplifier’s owner’s manual
and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.
With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.
* Connect one or two rear speakers.
The output sound from the rear
speakers will be monaural even if you
connect two rear speakers.
• Make the following setting.
On-screen display Select:
Page
“Digital Output” “PCM” or
“Bitstream”
33
Connecting to an amplifier equipped with Dolby Surround Pro Logic
To ANALOG
AUDIO OUT
To audio
input
Amplifier equipped with
Dolby Surround Pro Logic
To wall outlet
Audio cable (not supplied)
Connecting to Optional Equipment (Continued)
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest
movies, and is now available to reproduce this realistic effect in the home. You can
enjoy motion picture and live concert DVDs with this dynamic realistic sound by
connecting the DVD player to a 6 channel amplifier equipped with a Dolby Digital
decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder,
you will obtain the full benefit of Pro Logic from the same DVD movies that provide
full 5.1-channel Dolby Digital soundtracks, as well as from titles with the Dolby
Surround mark.
Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks of
Dolby Laboratories.
• Use DVDs encoded via the Dolby
Digital recording system.
• Make the following setting.
On-screen display Select:
Page
“PCM” or
“Bitstream”
“Digital Output”
Connecting to an amplifier equipped with a Dolby®Digital decoder
To COAXIAL
type digital
audio input
Amplifier equipped with a
Dolby Digital decoder
To wall outlet
Connect
either
Optical digital cable
(not supplied)
75 Ω coaxial cable (not supplied)
33
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

15
Connections
Connections
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an
amplifier equipped with a digital audio input and speaker system (right and left
front speakers).
75 Ω coaxial cable (not supplied)
• Make the following setting.
On-screen display Select:
Page
“PCM”
“Digital Output”
MPEG2 sound
You can enjoy motion picture and live concert DVDs with dynamic realistic sound
by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2
audio processor.
• Use DVDs encoded via the MPEG2
recording system.
• Make the following setting.
On-screen display Select:
Page
“PCM” or
“Bitstream”
“Digital Output”
Connecting to an amplifier equipped with an MPEG2 audio decoder
Connecting to an amplifier equipped with a digital audio input
Amplifier equipped with an
MEPG2 audio decoder
To COAXIAL
type digital
audio input
To wall outlet
Connect
either
Optical digital cable
(not supplied)
Amplifier equipped with
a digital audio input
To COAXIAL
type digital
audio input
To wall outlet
Connect
either
Optical digital cable
(not supplied)
75 Ω coaxial cable (not supplied)
33
33
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for
home use, on DVDs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefit of 5.1
channel DTS encoded sound tracks on DVDs or audio CDs.
• Use DVDs or audio CDs encoded
via the DTS recording system.
• Make the following setting.
On-screen display Select:
Page
“Digital Output” “Bitstream”
To COAXIAL
type digital
audio input
To wall outlet
Connect
either
Optical digital cable
(not supplied)
Amplifier equipped with
a DTS decoder
75 Ω coaxial cable (not supplied)
33
Connecting to an amplifier equipped with a DTS®decoder
Manufactured under license under U.S.
Patent #: 5,451,942 & other U.S. and
worldwide patents issued & pending.
DTS and DTS Digital Out are registered
trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc.
© 1996-2008 DTS, Inc. All Rights
Reserved.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

16
Basic playback
To turn the power off
Press ON/STANDBY to turn the unit off.
Notes
• Do not move the DVD player during playback. Doing so may
damage the disc.
• Use the OPEN/CLOSE button to open and close the disc tray.
Do not push the disc tray while it is moving. Doing so may cause
the DVD player to malfunction.
• Do not push up on the disc tray or put any objects other than
discs on the disc tray. Doing so may cause the DVD player to
malfunction.
• In many instances, a menu screen will appear after playback of
a movie is completed. Prolonged display of an on-screen menu
may damage your television set, permanently etching that image
onto its screen. To avoid this, be sure to press the STOP button
on your remote control once the movie is completed.
Playing a Disc
This section shows you the basics on how to play a disc.
CAUTION
Keep your fingers well clear of the disc tray as it is closing.
Neglecting to do so may cause serious personal injury.
Preparations
• When you want to view a disc, turn on the TV and select the
video input connected to the DVD player.
• When you want to enjoy the sound of discs from the audio
system, turn on the audio system and select the input
connected to the DVD player.
Notes
• If the disc tray is holding a disc you have already played, playback
will begin from the location where you last stopped. For resuming
playback, see
17
.
• Some video CD are recorded with PBC (Playback Control), a
menu with recorded contents may appear on the TV if you have
turned the PBC on. You can make your selection according to
its PBC menu. Press the PBC button on the remote control to
turn PBC on or off anytime during Video CD playback. When
switching from PBC off to PBC on mode, playback will start from
the beginning of the disc.To turn on the menu display again, press
the RETURN button.
To pause playback (still mode)
Press PAUSE/STEP during playback.
To resume normal playback, press the
PLAY button.
• The sound is muted during still
mode.
To stop playback
Press STOP.
To remove the disc
Press OPEN/CLOSE.
Remove the disc after the disc tray
opens completely.
Basic playback
To start playback in the stop mode
Press PLAY.
To obtain a higher quality picture
Occasionally, some picture noise not usually visible during
a normal broadcast may appear on the TV screen while
playing a DVD because the high resolution pictures on
these discs include a lot of information. While the amount
of noise depends on the TV you use with this DVD player,
you should generally reduce the sharpness adjustment on
your TV when viewing DVDs.
If you insert a DVD that contains a top menu, a
menu may appear. Use / / / to select the
title you want to view, then press ENTER to start
playback.
• You may need to press the TOP MENU or MENU
button to display disc menu (depending on the actual
DVD.)
Press the ON/STANDBY button.
The DVD player turns on.
Press OPEN/CLOSE.
The disc tray opens.
Place the disc on the disc tray.
With the playback
side down
• There are two different disc sizes. Place the disc in
the correct guide on the disc tray. If the disc is out
of the guide, it may damage the disc and cause the
DVD player to malfunction.
• Do not place a disc which is unplayable in this DVD
player.
Press OPEN/CLOSE to close the disc tray.
Playback starts.
1
2
3
4
ON/STANDBY
Be sure to press the OPEN/CLOSE
button to close the disc tray after you
remove the disc.
Automatic Power Off function
If the DVD player is stopped, or the screen saver is
engaged for approximately 20 minutes, the DVD player
will automatically turn itself off.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

17
Basic playback
Playing in fast reverse or fast forward directions
Press REV or FWD during playback.
REV: Fast reverse playback
FWD: Fast forward playback
Each time you press the REV or
FWD button, the playback speed
changes.
To resume normal playback
Press PLAY.
Notes
• The DVD player mutes sound and subtitles during reverse
and forward scan of DVDs.
• The playback speed may differ depending on the disc.
Playing in slow-motion
Press SLOW during playback.
Each time you press the SLOW
button, the slow-motion speed
changes in the following sequence:
To resume normal playback
Press PLAY.
Notes
• The sound is muted during slow-motion playback.
• 3 speeds are available.
Press PAUSE/STEP during still playback.
Each time you press the PAUSE/
STEP button, the picture advances
one frame.
To resume normal playback
Press PLAY.
Note: The sound is muted during frame by frame playback.
Playing frame by frame
Resuming playback from the same location
Notes
• There may be a difference in the location where playback
resumes depending on the disc.
• Settings you changed using the on-screen displays while the
DVD player keeps a location in the memory may function only
after the memory is cleared.
• Resuming playback does not work for VCD with PBC on.
Press STOP at the location where you
want to interrupt playback.
The DVD player memorizes the
location where playback is stopped.
Press PLAY.
The DVD player resumes playback
from the location where you stopped
playback.
1
2
Variable Speed Playback
You can play discs at various speeds, and resume playback from the location where you stopped playback.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

18
Basic playback
Locating a specific chapter or track
Press SKIP or repeatedly to access the
chapter or track number you want.
Playback starts from the selected chapter or track.
To locate succeeding chapters or tracks.
Playback starts from the beginning of the
current chapter or track.
When you press twice in quick successions,
playback starts from the beginning of the
preceding chapter or track.
Note
• Some titles may not display chapter numbers.
Normally, DVDs are divided into titles, and the titles are sub-divided into chapters. VIDEO CDs and audio CDs are divided into
tracks. You can quickly locate any specific title, chapter, or track.
Locating a title using the top menu
Press TOP MENU.
The top menu appears on the TV
screen.
e.g.
Press / / / to select the title you
want.
If the titles in the top menu are
assigned a number, you can directly
locate a specific title by pressing its
designated number with the number
buttons.
Press ENTER.
Playback starts from chapter 1 of the
selected title.
1
2
3
Notes
• The instructions above describe basic procedures which may
vary depending on the contents of the DVD.If different instructions
appear on the TV screen, follow those instructions.
• If you display the top menu during playback and press the TOP
MENU button again without selecting any title, the DVD player
may resume playback from the point where you first pressed
the TOP MENU button (depending on the actual DVD.)
• This method of locating a title is available only on a disc that
contains a top menu.
• Instruction notes of discs may refer to the button that displays
the top menu as TITLE button.
Locating a Desired Section
To start playback from the beginning regardless of the location where you stopped playback.
1 Press STOP twice.
The DVD player deletes the memory of the location.
2 Press PLAY.
Playback starts from the beginning of the current title.
Playback starts from the beginning of the disc.
Playback starts from the beginning of the current track.
• If you want to return to the beginning of a DVD, open and close the disc tray once with the OPEN/CLOSE button
before pressing the PLAY button.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

19
Advanced playback
Accessing a Specific Location Directly
Locating a specific title/chapter/time
Press T.
Press / to highlight the Title/Chapter/
Track/Time.
Press / to select a section you want
to locate.
1
2
e.g. When you want to locate a
chapter.
SEARCH
T1
2
Track
Time
Disc Time
00:00:00
00:00:00
1
00:00:00
e.g.
Or
Press the number buttons to enter title,
chapter (track) number or time.
Press ENTER.
Playback starts from the selected
section.
3
Notes
• Pressing the CLEAR button resets the numbers.To clear the
display, press the T button several times.
• For VCD with PBC on, accessing tracks using number buttons
does not work.
To set and play favorite bookmark during
playback
1. Press T twice, the display of Bookmark appears, then
press ENTER to mark the desired scene.
2. Press ENTER to play the favorite bookmark.
To set other bookmarks.
Follow step 1 and move through the menu by pressing
the or button.
Press T again to remove this display.
To cancel the Bookmark
Follow step 1, then press the CLEAR button to cancel
the bookmark. Move through the menu by pressing the
or button to cancel other bookmarks.
Notes
• Some discs may not work with marking operation.
• The marking is canceled when you open the disc tray or turn
the power off.
• Some subtitles recorded around the marker may fail to
appear.
Bookmark
Accessing chapters/tracks using number
buttons:
For chapter/track numbers 10 to 19, press +10 once
and the number 10 appears then enter the second
digit. Press ENTER.
For chapter/track numbers 20 to 29, press +10 twice
and the number 20 appears then enter the second
digit. Press ENTER.
For example, if you want to select chapter/track 25,
first press +10 twice then press the number button
“5”. Then press ENTER.
Accessing the time using number buttons:
Just enter 2 digits in order.
The first two numbers you entered represent hours.
The second two numbers you entered represent
minutes.
The third two numbers you entered represent
seconds.
Advanced playback
SEARCH
T
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals

20
Advanced playback
Repeating a Specific Segment
You can specify a desired segment and repeat it.
Repeating a specific segment
To resume normal playback
Press A-B RPT until RepAB Off is displayed.
Notes
• Some discs may not permit A-B repeat operation.
• You cannot set the A-B repeat function for a segment that
includes multiple camera angles.
• You can specify a segment only within the current title or track
(VIDEO CD).
• There may be a slight difference between point A and the
location where playback actually resumes depending on the
disc.
Press A-B RPT at the beginning of the
segment (point A) you want to play
repeatedly.
Press A-B RPT again at the end of the
segment (point B).
The DVD player automatically returns to
point A and starts repeat playback of the
selected segment (A-B).
2
1
A-B RPT
Playing in a Varied Order
You can play titles, chapters within a title, or tracks in a varied order.
For Audio CD, please see “Playing MP3/WMA files”
26
.
Playing titles, chapters or tracks in a varied order
Press PLAY MODE.
Press / button to select desired
features and then press ENTER button
to toggle desired mode.
1
e.g.
Shuffle: Playbacks in random order.
PBC: Playbacks in PBC On mode (VCD only).
Chapter: Repeats the current chapter.
Title: Repeats the current title.
Single: Repeats the current track.
All: Repeats the entire disc.
Off: Resumes normal playback.
Normal
Shuffle
Mode Normal
Repeat
Chapter
Title
Single
PBC
(
VCD onl
y)
Play Mode
:Off
PLAY MODE
Press PLAY.
Press the PLAY button, the DVD player
starts playback in the selected mode.
To resume normal playback
Press ENTER until the Off/Normal is displayed.
Note
Some discs may not permit these operations.
2
Rep A-
Rep A-B
RepAB Off
A-B RPT
A-B RPT
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Toshiba Manuals