Toshiba F-LYA20HKG User manual

READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.
OWNER’S MANUAL
Electric Fan
MODEL: F-LYA20(W)HKG

Read Rules for Safe Operation and Instructions Carefully.
CAUTION
WARNING
1. If the supply cord is damaged, it must be replaced by manufacturer,its service
agent or a similarly qualied person in order to avoid a hazard.
2. This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experi-
ence and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user mainte-
nance shall not be made by children without supervision.
3. Correct Disposal of this product
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the envi-
ronment or human health from uncontrolled waste disposal, recycle it respon-
sibly to promote the sustainable reuse of material resources. To return your
used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.The packaging material is recyclable. Dispose of
the packaging in an environmentally friendly manner and make it available for
the recyclable material collection-service.
4. Indoor and household use only.
5. When the appliance is not in use and before cleaning, unplug the appliance
from the outlet.
6. To protect against the risk of electrical shock, do not disassemble the fan and
do not immerse the unit, cord or plug in water or other liquid.

Product Introduction
Name of Each Component
Machine
head
Pole
Chassis
Rear Grill Blade Front Grill

2
1
2
Control Panel
Turn on/o the oscillating button
Wind speed button
On/standby button
Status indicator
Installation Instructions
Installation preparation
Please take out the lock nut of blade from the front enclosure of the
motor clockwise, and then take out the lock nut of grill counterclock-
wise before installing.
Lock nut of grill Lock nut of blade
(Clockwise direction)(Anti-clockwise direction)

3
Pole Installation
Installation Procedures
Chassis Installation
Position the pole and chassis sockets
in the direction shown, insert the pole
into the chassis socket and stabilize it;
Insert the bolt into the hole at the bottom of
the chassis and tighten the bolt to x the
pole and chassis.
Chassis
pole
First, you need to align the hole of the
machine body with the pole, then rotate it
in and x it to complete the installation of
the pole, be sure to rotate in place.
Rear Grill Installation
According to the direction shown, make the
rear grill of the fan upward in the direction of
the arrow, and make the round hole aligned
with the salient point on the front enclosure of
the motor;
After the motor head is hung on the rear grill,
rotate the plastic nut clockwise to lock the
rear grill.
Convex
cylinder
Round hole
Lock nut of grill
The arrow mark of the upper column tube
is to be within the identication range of
the lower column tube.

4
Blade Installation
Align the blade with the motor shaft and
put it on, and the side with warning label
of the blade faces outward; Rotate the
spinner counterclockwise to lock the
blade.
Concave and convex clamping
Lock nut of blade
(Anti-clockwise
direction)
Front Grill Installation
First, nd the front and rear
grill clamping, and stabilize
the front grill to the rear grill
buckles;
Insert the clamping
Press the mesh enclosure by
both hands in sequence, and
when you hear a ''click'', the
installation is in place.
Power Up
After installation, plug on the machine. After
hearing the "drop", the fan is powered on
successfully.
Then fasten the net buckle at the bottom
of the front grill, insert the mesh enclosure
screw into the hole of the net buckle, and
tighten it with a screwdriver.
Note: 1. The mesh enclosure screw is xed at the
rear grill clamping, and the user needs to
unscrew the screw and then install it.
2. Be sure to install the net cover when running.

5
Instructions for Use
Panel of machine head
Timing/reserved
indicator
Low-grade
wind indicator Medium-grade
wind indicator
High-grade
wind indicator
On/standby button
Wind speed button
Turn on/o the
oscillating button
Instructions of buttons on the machine head
Icon Function description
Icon Function description
Startup/Standby
Switch to the normal wind grade by pressing the low→medium→
high→low to cycle
Turn on/off shaking the head to supply wind
Descriptions for the indicators
Indicate timing/reserved status
Normal wind of low grade, grade 1
Normal wind of medium grade, grade 2
Normal wind of high grade, grade 3, Strong wind model
Note: ①If timing turning o/on reserved is set for 1 hour, the timing/reserved indicator will be on; If it is set for 2 hours, timing/reserved indicator and low-grade
wing indicator will be on; If it is set for 3 hours, timing/reserved indicator , low and medium-grade wind indicator will be on; If it is set for 4 hours, 4 indicators will
be all on;
②The machine has a screen-o function in order to reduce the interference of light, which means if there is no operation within 60 seconds, all the indicators
will go out. At this time, the fan runs or stops without display, which is normal and is not a malfunction.

6
Panel of Remote controller
Turn on/o
the oscillating
button
Strong wind
button
Button of wind volume
decrease
(Timing time decrease)
On/ standby button
Fan speed button
Button of wind volume increase (Timing
time increase)
Timing/reserved button
(AAA battery 1.5V)
Power assembly
drawing
Please use a manganese or alkaline battery of
type "AAA" and do not use a non-recyclable
battery.
Control range of remote controller
The remote controller control can be normally
used within 5 meters in front of the product and
in the left and right angles of 30 degrees.
Specications for remote controller buttons
Icon Function description
Turn on/Standby
Turn on/off oscillating to supply wind
Switch to the normal wind grade by pressing the low→
medium→high→low to cycle
Switch to the normal wind grade, wind speed and grade are
increasing;
Switch the time, the timing/reserved time is increasing.
Switch to the normal wind grade, wind speed and grade
are decreasing;
Switch the time, the timing/reserved time is decreasing.
Turn on/off timing powering off, it will power off 1 hour later;
Turn on/off reserved powering on, it will power on 1 hour later.
Turn on/off strong wind
Press the timing button first, then press the “+、- ”button within
5 seconds, you can adjust the increase or decrease of the timing time,
for 4 hours timing range in total(1,2,3,4).

MAINTENANCE INSTRUCTION
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
Thoroughly remove soap lm with dry cloth.
The fan requires little maintenance. Do not try to x it by yourself. Refer it to
qualied service personnel if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.