Toshiba F-TSA20(G)MY User manual

OWNER’S MANUAL
Table Fan
MODEL: F-TSA20(G)MY
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the Intruction manual are for reference only.

1
Read Rules for Safe Operation and Instructions Carefully.
CAUTION
1. If the supply cord is damaged, it must be replaced by manufacturer
or its service agent or a similarly qualified person in order to avoid
a hazard.
2. Indoor use only.
3. To protect against the risk of electrical shock, do not immerse the
unit, cord or plug in water or other liquid.
4. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
5. When the appliance is not in use and before cleaning, unplug the
appliance from the outlet.
6. Keep electrical appliances out of reach from children or infirm
persons. Do not let them use the appliances without supervision.
7. When the fan was assembled, the rotor blade guard shall not be
taken off anymore
- Prior cleaning unplug the fan
- The rotor guard shall not be dissembled/ opened to clean the
rotor blades.
- Wipe the fan enclosure and rotor blade guard with a slightly
damp cloth.
WARNING
1. Never insert fingers, pencils, or any other object through the guard when fan is
running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid overturning.
4. DO NOT use fan near to window, rain may create electrical hazard.
5. Indoor use only.
RULES FOR SAFE OPERATION
6. Operate the fan after ensuring the guard and blade is installed.

2
65 4 32
1
OPERATING INSTRUCTIONS
Name of components
Front guard Rear guard
Motor
shaft Motor
Oscillating
Clutch Knob
Install by
aligning
Pole
Lock nut of blade
Lock nut of blade
anticlockwise,
and then install the
front fan cover.
Blade
Pull the blade to rotate after installing,
so as to ensure that the blade can be
normally rotated.
Lock nut of guard
Screw the lock nut of guard clockwise,
and in the meantime, fix the rear guard.
Base
1
2
3
1
2
3
Front and Rear Guard Installation
Align Catch of the Front Guard
with the illustrated position of
the Rear Guard.
Press guards sequentially
with both hands.
Self-Catch Installation.

3
INSTRUCTIONS FOR USE
0 1 2 3
Body key
Oscillate control
Pull up-stop push down-oscillate
Oscillating
Clutch Knob
Tilt Adjustment
Manual

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified
service personnel if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner, bending.
5. Do not allow water or any other liquid into the motor housing or interior parts.
MAINTENANCE INSTRUCTION
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
Thoroughly remove soap film with dry cloth.
SPECIFICATIONS
F-TSA20(G)MY
220-240V~
55W
50Hz
L : 452mm
W : 290mm
H : 600mm
ø400mm
None
Approx. 3.4 kg
Model
Rated voltage
Rated Frequency
Power consumption
Blade Diameter
Unit Diamension
Net weignt
Accessories