Toshiba RBC-AMT32E User manual

163
Wired remote controller (RBC-AMT32E)
Operation manual
PartsName of Remote Controller
Display section
In the display example, all indicators are displayed for the explanation.
In reality only, the selected contents are indicated.
• When turning on the main power switch and leak breaker at the first
time,
SETTING
flashes on the display part of the remote controller.
• While this display is flashing, the model is being automatically
confirmed.
Accordingly, wait for a while after
SETTING
display has disappeared, and
then use the remote controller.
1SETTING display
Displayed during setup of the timer etc.
2Operation mode select display
The selected operation mode is displayed.
3CHECK display
Displayed while the protective device works or a
trouble occurs.
4Timer time display
Time of the timer with H mark is displayed.
(When a trouble occurs, the check code is
displayed.)
5Timer SET IN setup display
When pushing the Timer SET IN button, the
display of the timer is selected in order of
[OFF] [OFF] repeat OFF timer
[ON] No display.
6Filter display
If “FILTER ” is displayed, clean the air filter.
7TEST run display
Displayed during a test run.
8Louver position display
(4-way Air Discharge Cassette,
2-way Air Discharge Cassette,
1-way Air Discharge Cassette, Under Ceiling
and High Wall Type only (2H. 3H))
Displays louver position.
9SWING display
Displayed during up/down movement of the louver.
10 Set up temperature display
The selected set up temp. is displayed.
11 Remote controller sensor display
Displayed while the sensor of the remote
controller is used.
12 PRE-HEAT display (Heat-pump model only)
Displayed when the heating operation starts or
defrost operation is carried out.
While this indication is displayed, the indoor fan
stops or the mode enters in LOW.
13 No function display
Displayed if there is no function even if the
button is pushed.
Display
section
Operation
section
S
ET
TIME
TIMER SET
TEST
FIL
TER
L
L
RESET
TE
CL
FA
N
SA
VE
A
A
S
WING/FI
X
VENT
MODE
OFF
UNIT
LOUVER
5
1
8
920 19
3
2
4
6
715
14
18
11
16
17
13 12
10
This remote controller can control
the operation of Max. 8 indoor units.

164
14 Air volume select display
The selected air volume mode is displayed.
(AUTO) (HIGH)
(MED.) (LOW)
15 Louver Number display
(exapmle:01, 02, 03, 04)
16 Operation ready display
Displayed when cooling or heating operation is
impossible because the outdoor temperature
goes out of the operable range.
17 Mode select control display
Displayed when pushing “Operation mode select
” button while the operation mode is fixed to
heating or cooling by the system manager of the
air conditioner.
18 Louver lock display
(4-way Air Discharge Cassette Type
2H series only)
Displayed when there is a louver-locked unit in the
group (including 1 indoor unit by 1 outdoor unit).
19 Unit Number display
Unit number of the indoor unit selected with
the unit select button or abnormal indication of
the indoor/outdoor unit.
20 Central control display
Displayed when the air conditioner is used
under the central control in combination with a
central control remote controller.
In case the remote controller is disabled by the
central control system, flashes.
The button operation is not accepted.
Even when you push ON/OFF, MODE, or
TEMP. button, the button operation is not
accepted.
(Settings made by the remote controller vary
with the central control mode. For details, refer
to the Owner’s Manual of the central control
remote controller.)
5
1
8
920 19
3
2
4
6
715
14
18
11
16
17
13 12
10

165
Operation section
Push each button to select a desired operation.
• The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing
ON / OFF
button only.
1
FAN
button (Air volume select button)
Selects the desired air volume mode.
2
TIMER SET
button (Timer set button)
TIMER SET button is used when the timer is set up.
3
TEST
button (Check button)
The CHECK button is used for the check operation.
During normal operation, do not use this button.
4
VENT
button (Ventilation button)
Ventilation button is used when a fan which is
sold on the market is connected.
• If “No function ” is displayed on the remote
controller when pushing the Ventilation button, a
fan is not connected.
5
FILTER
RESET
button (Filter reset button)
Resets (Erases) “ FILTER” display.
6
SAVE
button (Power save operation)
7
SWING/FIX
button (Swing/Wind direction button)
Selects automatic swing or setting the louver
direction.
• This function is not provided to Concealed Duct
Standard Type, High Static Pressure Type,
Floor Standing Cabinet Type, Floor Standing
Concealed Type, or Slim Duct Type.
8Operation lamp
Lamp is lit during the operation.
Lamp is off when stopped.
Also it flashes when operating the protection
device or abnormal time.
9
ON / OFF
button
When the button is pushed, the operation starts,
and it stops by pushing the button again.
When the operation has stopped, the operation
lamp and all the displays disappear.
10
MODE
button (Operation mode select button)
Selects desired operation mode.
11
UNIT LOUVER
button (Unit/Louver select button)
Selects a unit number (left) and louver number
(right).
UNIT:
Selects an indoor unit when adjusting wind
direction when multiple indoor units are
controlled with one remote controller.
LOUVER (4-way Air Discharge Cassette
Type 2H series only):
Selects a louver when setting louver lock or
wind direction adjustment independently.
12
TEMP.
button (Set up temperature button)
Adjusts the room temperature.
Set the desired set temperature by pushing
TEMP. or TEMP. .
OPTION :
Remote controller sensor
Usually the TEMP. sensor of the indoor unit senses
the temperature. The temperature on the surrounding
of the remote controller can also be sensed.
For details, contact the dealer from which you have
purchased the air conditioner.
• In case that one remote controller controls the
multiple indoor units, the setup operation is unavail-
able in group control.
1
8
3
5
2
9
10
11
6
7
4
12
S
ET
TIME
TIMER SET
TEST
FIL
TER
L
L
RESET
TEMP
.
CL
FA
N
SA
V
E
A
A
S
WING/FI
X
VENT
MODE
ON / OFF
UNIT
LOUVER

166
Correct Usage
• When you use the air conditioner for the first time or when you change the SET DATA value, follow the
procedure below. From the next time, the operation displayed on the remote controller will start by pushing the
ON / OFF
button only.
Preparation
Turn on the main power switch and/or the leakage breaker.
• When the power supply is turned on, a partition line is displayed on the display part of the remote controller.
After the power supply is turned on, the remote controller does not accept an operation for approx. 1 minute,
but it is not a failure.
REQUIREMENT
• While using the air conditioner, operate it only with
ON / OFF
button without turning off the main power switch
and the breaker.
• When you use the air conditioner after it has not been used for a long period, turn on the power switch at least
12 hours before starting operation.
Start
1 Push
ON / OFF
button.
The operation lamp goes on, and the operation
starts.
2 Select an operation mode with the
“MODE
MODE
” button.
One push of the button, and the display changes
in the order shown as follows.
• “
DRY mode” function is not provided to
Concealed Duct High Static Pressure Type.
3 Select air volume with “
FAN
” button.
One push of the button, and the display changes
in the order shown as follows.
• When air volume is “
AUTO”, air volume
differs according to the room temperature.
• In
DRY mode, “
AUTO” is displayed and
the air volume is LOW.
• In heating operation, if the room temperature is
not heated sufficiently with VOLUME “ LOW”
operation, select “
MED.” or “
HIGH”
operation.
• The temperature sensor senses temperature near
the air inlet of the indoor unit, which differs from
the room temperature depending on the installa-
tion condition.
A value of setting temperature is the measure of
room temperature.
(“
AUTO” is not selectable in the FAN mode.)
• Air volume of function is not provided to
“Concealed Duct High Static Pressure Type” but
air speed “
HIGH” only is displayed.
4 Determine the set up temperature by pushing
the “TEMP.
” or “TEMP. ” button.
Stop
Push
ON / OFF
button.
The operation lamp goes off, and the operation stops.
HEAT
DRY COOL FAN
Heat-pump model
DRY COOL FAN
Cooling only model
(Dehumidify)
A
UTO HIGH MED. LOW
S
ET
TIME
TIMER SET
TEST
FIL
TER
L
RESET
TEMP
.
CL
FA
N
SA
VE
A
A
S
WING/FI
X
VENT
MODE
ON / OFF
UNIT
LOUVER
2
3
1
4

167
[In case of cooling]
• Start the cooling operation after approx. 1 minute.
[In case of heating (For Heat-pump model only)]
• The heating operation mode is selected in accordance with the room temperature and operation starts after
approximately 3 to 5 minutes.
• After the heating operation has stopped, FAN operation may continue for approx. 30 seconds.
• When the room temperature reaches the set temperature, the super low wind is discharged and the air volume
decreases excessively.
• During defrost operation, the fan stops so that cool air is not discharged. (“
PRE-HEAT” is displayed.)
NOTE
When restarting the operation after stop
• When restarting the operation immediately after stop, the air conditioner does not operate for approx.
3 minutes to protect the machine.
For best cooling and heating performance, adjust the louvers (adjustment of up/down wind direction) appropriately.
CAUTION
• If cooling operation is performed with downward air outlet, dew may fall on surface of the cabinet or the
horizontal louver resulted in dripping.
• If heating operation is performed with horizontal air outlet, unevenness of temperature may increase in the room.
• Do not move the horizontal louver directly with hands; otherwise a trouble is caused.
Select direction of the horizontal louver using
SWING/FIX
switch on the remote controller.
The horizontal louver does not stop immediately even if the switch is pushed.
Adjusting the stop position, push the switch.
For all models
[In Cooling operation]
Use the louvers with horizontal set point.
[In Heating operation (For Heat-pump model only)]
Use the louvers with downward set point.
For Under Ceiling, 1-way Air Discharge Cassette, High Wall Type
[Right / Left air direction adjustment]
To change the air outlet direction to right or left side, set the vertical louver inside of the horizontal louver to the
desired direction.
Adjustment of Wind Direction