Toshiba Strata DK8 User manual

Issue 1, March 1993
STRATA DK STANDARD TELEPHONE
Release 1
© COPYRIGHT 1993 TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
All rights reserved. No part of this manual may be reproduced in any form or by any means — graphic, electronic, or
mechanical, including recording, taping, photocopying, or the use of information retrieval systems — without express written
permission of the publisher of this material.
STANDARD TELEPHONE USER GUIDE

STRATA DK STANDARD TELEPHONE
TRADEMARKS AND SERVICE MARKS
The following trademarks and service marks are used in this document:
■STRATA®: registered trademark of Toshiba America Information Systems, Inc.
In accordance with U.S. Copyright Law, a license may be required from the American Society of Composers,
Authors, and Publishers, or other similar organization, if radio or television broadcasts are used for the Music-
on-Hold feature of this telecommunications system. Toshiba America Information Systems, Inc. disclaims any
liability arising out of the failure to obtain such a license.
Toshiba America Information Systems, Inc. reserves the right to change any of this information including, but
not limited to, product characteristics and operating specifications, without prior notice.

Table of Contents
SUBJECT PAGE
INTRODUCTION
General Description.......................................................................................................... iii
Purpose ............................................................................................................................ iii
Organization ..................................................................................................................... iii
How to Use This Guide..................................................................................................... iv
FEATURE OPERATION
Outside Calls .................................................................................................................... 1-1
Intercom Calls................................................................................................................... 1-1
Automatic Callback........................................................................................................... 1-2
Call Forward ..................................................................................................................... 1-3
Call Hold/Park................................................................................................................... 1-4
Call Transfer with Camp-on.............................................................................................. 1-5
Conference Calls.............................................................................................................. 1-6
Door Phone....................................................................................................................... 1-8
Flash CO Line................................................................................................................... 1-9
Account Code Calls.......................................................................................................... 1-9
Forced Account Codes................................................................................................. 1-9
Emergency Override of Forced Account Code Dialing................................................. 1-10
Voluntary Account Codes............................................................................................. 1-10
Verified Account Codes................................................................................................ 1-11
Message Waiting Indication.............................................................................................. 1-11
Override Calls................................................................................................................... 1-12
Paging............................................................................................................................... 1-12
Repeat Last Number Dialed ............................................................................................. 1-13
Speed Dial........................................................................................................................ 1-14
Tone/Voice First Signaling ............................................................................................... 1-15
CO Line Queuing.............................................................................................................. 1-15
Call Pickup........................................................................................................................ 1-16
Direct Inward System Access........................................................................................... 1-17
Toll Restriction Override/Traveling Class.......................................................................... 1-18
INDEX ................................................................................................................................................... Index-1
FIGURE LIST
FIGURE TITLE PAGE
I-1 Sample Page ........................................................................................................................ v
STRATA DK STANDARD TELEPHONE TABLE OF CONTENTS
i

STRATA DK STANDARD TELEPHONE TABLE OF CONTENTS
ii

Chapter 1
OUTSIDE CALLS
You can make calls to or receive calls from telephones outside of the
STRATA DK system.
You will hear intercom dial tone.
CO line number access codes are 7 0 1 ~ 7 0 4 (for DK8) and 7 0 1 ~
7 0 8 (for DK16). With some systems you may have to dial either the
general group code (9), Least Cost Routing code (9), or a Line Group
code (8 1 ~ 8 4 for DK8; 8 1 ~ 8 8 for DK16), instead of a CO line number
access code.
The ringing pattern depends on parameters set in system programming.
A distinct outside call ring pattern—0.2 seconds on, 0.4 seconds off, 0.2
seconds on, 3.4 seconds off—is optionally available. Some systems may
use the intercom ring pattern—one second on, 3 seconds off—for
incoming outside calls.
INTERCOM CALLS
You can make calls to and receive calls from other stations in the
STRATA DK system.
You will hear intercom dial tone.
If the called station is idle:
■You will hear a single tone if you are calling a digital or electronic
telephone station. Speak after you hear the tone.
■If the system was set for Tone Signaling, instead of Voice First
Signaling, you would hear repetitive tone ringing for all calls. (You
To Make an Outside Call:
1. Lift the handset.
2. Dial a CO line number access
code.
3. Dial the desired telephone
number.
To Receive an Incoming Call:
1. You will hear ringing.
2. Lift the handset and speak.
To Make an Intercom Call (Voice
First Signaling):
1. Lift the handset.
2. Dial the desired station
number.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-1

To Receive an Intercom Call:
1. You will hear ringing.
2. Lift the handset and speak.
To Set Automatic Callback
(Voice First Signaling):
1. After reaching a busy station,
dial 4.
2. Hang up.
3. Your telephone will ring at a
fast rate when the called
station becomes idle.
can change the signaling mode by pressing 1 after dialing the digital
or electronic station number. See Tone/Voice First Signaling later in
this guide.)
■If you are calling another standard telephone, you will hear repetitive
ringing. Wait for the called station user to answer.
■To leave a Message Waiting Indication at the called station, dial 7.
If you receive busy tone:
■To set Automatic Call Back (ACB), dial 4.
■To activate Busy Override if the called digital or electronic telephone
station is not equipped for Off-hook Call Announce (OCA), dial 2.
(Standard telephones cannot be equipped to receive OCA.)
■To activate OCA at digital or electronic telephones: With Voice First
Signaling and if the called station is equipped for OCA, dial 2. With
Tone Signaling and the called station is equipped for OCA, dial 21.
■To leave a Message Waiting Indication at the called station, dial 7.
■Hang up and try again later.
The intercom ring pattern is one second ringing, three seconds silence.
You will be connected to the calling party.
AUTOMATIC CALLBACK
After reaching a busy station or a telephone in the Do Not Disturb (DND)
mode, you may set Automatic Callback to have the system call you back
when the called station is no longer busy or in the DND mode. Automatic
Callback does not apply to outside calls.
The busy tone will stop. You will hear dial tone for two seconds, then the
busy tone will resume.
You may make other calls while waiting for the called station to become
available.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-2

Answer within three rings to prevent the callback from being cancelled.
You will hear a single tone, as if making a regular intercom call. (If using
Tone Signaling instead of Voice First Signaling, you would hear repetitive
ringing.)
If you hear busy tone after answering, it means the called party has
already received or originated another call. Your request is not cancelled.
You will be called again when the station becomes idle.
NOTE: You may cancel the request anytime prior to the callback by
lifting the handset and dialing 4 3.
CALL FORWARD
You can set your station to call forward to another station or voice mail
under a variety of conditions.
■Call Forward-All Calls—If your station is idle or busy and has this
feature activated, all calls to it will forward immediately to another
station that you preselect. Your station will not ring.
■ Call Forward-Busy—Calls to your telephone while you are busy on
another call will forward immediately to another station that you
preselect if this feature is set. Calls will ring as normal if your
telephone is idle.
■Call Forward-No Answer—Calls to your station when set with this
feature will forward to another station that you preselect if you fail to
answer within 12 seconds or three rings.
■Call Forward-Busy/No Answer—Calls to your station when set with
this feature will forward immediately to a station that you preselect
whenever you are busy on another call. Calls will also forward if you
do not answer within 12 seconds or three rings.
You will hear intercom dial tone.
4. Answer the call immediately.
5. Make voice announcement
and then converse.
To Set Call Forward:
1. Lift the handset.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-3

2. Dial one of the following Call
Forward access codes:
6 0 1 = Call Forward-All
Calls
6 0 2 = Call Forward-
Busy
6 0 3 = Call Forward-No
Answer
6 0 4 = Call Forward-
Busy/No Answer
3. Enter the station or voice mail
intercom number to which
calls will forward.
4. Hang up.
To Cancel Any Call Forward
Mode:
1. Lift the handset.
2. Dial 6 0 1.
3. Hang up.
You will hear confirmation tone.
You will hear confirmation tone again and then busy tone.
Calls will forward as applicable.
NOTES:
1. You may continue using your phone in the usual manner while Call
Forward is in effect.
2. If Call Forward is set:
■ CO lines that ring your station only will forward—CO lines that
ring more than one station will not forward.
■ CO line calls transferred to your station will forward.
■ Intercom calls will forward.
■ Call Forward has priority over the hunt feature set in system
programming.
You will hear intercom dial tone.
This code will cancel any of the Call Forward modes.
You will hear confirmation tone again, then busy tone.
CALL HOLD/PARK
You can place a call on hold and then make another call.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-4

“Flash the hookswitch” by depressing the hookswitch (plunger) located in
the handset cradle for about 1/2 second. (Some telephones may have a
special button which flashes the hookswitch when pressed.)
You must hang up for at least two seconds for the call to be placed on
hold.
You may now originate or receive other calls.
You will hear intercom dial tone.
You will be reconnected with the held/parked call.
NOTES:
1. If you do not return to the call within a designated time period, your
telephone will ring to recall you.
2. Any other station can pick up the held call by:
■ Obtaining intercom dial tone and dialing 5 + your intercom
number.
■ Obtaining intercom dial tone and dialing 5 7 + the number of the
held CO line, 0 1 ~ 0 4 (for DK8) or 0 1 ~ 0 8 (for DK16).
CALL TRANSFER WITH CAMP-ON
This feature allows you to transfer an outside call to a station that is
either idle or busy.
“Flash the hookswitch” by depressing the hookswitch (plunger) located in
the handset cradle for about 1/2 second. (Some telephones may have a
special button which flashes the hookswitch when pressed.)
You will hear intercom dial tone after flashing the hookswitch.
To Place a Call On Hold/Park:
1. While on a call, flash the
hookswitch.
2. Dial 4 1 and hang up.
To Return to the Held/Parked
Call:
1. Lift the handset.
2. Dial 4 2.
To Transfer a Call (Voice First
Signaling):
1. While on an outside call, flash
the hookswitch.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-5

2. Dial the station number to
which the call will be
transferred.
3. If the called station is idle,
announce the call after the
single ring tone and then
hang up.
. . . or . . .
If the called station is busy,
hang up.
To Add a Station to an Existing
Call:
1. While on either an outside call
or intercom call, flash the
hookswitch.
You can flash the hookswitch again to reconnect to the outside line
before it is transferred. If the called station lifts the handset (or presses
their intercom button on digital and electronic telephones) just before you
flash the hookswitch again, you will enter a conference call.
If the call was made with Tone Signaling instead of Voice First Signaling,
you would hear repetitive ringing after dialing the station number and you
could wait for the called party to answer.
The call will camp-on to the busy station. The called station will receive a
call waiting tone to know that a call has been transferred.
NOTE: The call will recall you by ringing your station (and camp-on will
be cancelled) if the station does not answer within a predetermined time.
Inform the caller of the situation, and repeat the procedure if necessary.
CONFERENCE CALLS
STRATA DK enables you to participate in a variety of Conference calls of
up to four parties:
■Up to four stations (including your own) may be conferenced on
intercom.
■Up to three stations (including your own) may be conferenced with
one CO line.
■Up to two stations (including your own) may be conferenced with two
CO lines.
NOTE: The STRATA DK8 supports two simultaneous conferences. If a
four party conference is in progress, the second conference may contain
three parties maximum.
“Flash the hookswitch” by depressing the hookswitch (plunger) located in
the handset cradle for about 1/2 second. (Some telephones may have a
special button which flashes the hookswitch when pressed.)
You will hear intercom dial tone after flashing the hookswitch and the call
will be placed on hold. You will not hear the held party again until Step 4.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-6

The new party must pick up the handset or press their intercom button to
participate in a Conference call.
All parties will be conferenced.
If the called station was busy, you could flash the hookswitch to return to
the existing call, or you could hang up and receive immediate recall
ringing to answer the existing call.
“Flash the hookswitch” by depressing the hookswitch (plunger) located in
the handset cradle for about 1/2 second. (Some telephones may have a
special button which flashes the hookswitch when pressed.)
You will hear intercom dial tone, and the existing call will be placed on
hold. You will not hear the held party again until Step 4.
CO line number access codes are 7 0 1 ~ 7 0 4 (for DK8) and 7 0 1 ~
7 0 8 (for DK16). With some systems, you may have to dial either the
general group code (9), Least Cost Routing code (9), or a Line Group
code (8 1 ~ 8 4 for DK8; 8 1 ~ 8 8 for DK16), instead of a CO line number
access code.
If the party is busy or does not answer, hang up to receive an immediate
recall to return to the existing call.
All parties will be conferenced.
Two CO lines maximum can be conferenced. Depending on
circumstances, the outside parties may experience difficulty hearing each
other.
2. Dial the number of the station
you want to add to the call.
3. If you hear a single tone,
voice announce the call and
ask the party to pick up.
4. Flash the hookswitch when
the party answers.
5. Repeat Steps 1 ~ 4 to add
another station to the
conference.
To Conference By Adding a CO
Line to a Call:
1. While on a CO line or
intercom call, flash the
hookswitch.
2. Dial a CO line number access
code.
3. Dial the desired telephone
number you wish to add to the
call.
4. Flash the hookswitch when
the party answers.
5. Repeat Steps 1 ~ 4 to add
another CO line to the
conference.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-7

To Call/Monitor a Door Phone:
1. Lift the handset.
2. Dial the intercom number for
the desired door location.
3. Hang up when the call is
completed or when you no
longer wish to monitor the
door phone.
To Pick Up a Door Phone Call
That Is Ringing Another Station:
1. You will hear a distinct ringing
tone at a digital or electronic
telephone, or on the paging
speaker.
2. Lift the handset.
3. Dial 5 3 0.
NOTES:
1. While a conference is being set up, all outside parties are held
separately and cannot converse with each other.
2. If a four-party conference is set, either inside station will maintain the
conference if the other hangs up. But one station must remain in the
conference to maintain the outside connections.
DOOR PHONE
You can call a door phone and monitor the immediate area surrounding
the door phone. Only digital and electronic telephone stations can be
called by door phone users, but you can pick up these calls when they
are incoming by lifting your handset and dialing a pick up access code.
You will hear intercom dial tone.
551 Location ____________________
552 Location ____________________
553 Location ____________________
554 Location ____________________
555 Location ____________________
556 Location ____________________
The phone will ring a maximum of once or five times, depending on
system programming.
You will hear intercom dial tone.
You will be connected to the door phone.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-8

FLASH CO LINE
Some CO line features like conferencing, Centrex features, or behind
PBX operation require “flashing” the CO (or Centrex) line.
The hookswitch is located in the handset cradle of your telephone. After
you press the hookswitch, you will hear intercom dial tone. (Some
telephones may have a special button which flashes the hookswitch
when pressed.)
You will hear Centrex or PBX dial tone.
ACCOUNT CODE CALLS
Account Codes can be used for a variety of reasons, including billing, call
tracking, and line restriction applications. The system records the
Account Codes and can print them out along with other call details on a
Station Message Detail Recording (SMDR) report.
FORCED ACCOUNT CODES
Some applications may require that you enter an Account Code, called a
Forced Account Code, before dialing a telephone number. Forced
Account Codes can be recorded for outgoing calls only.
You will hear intercom dial tone.
CO line number access codes are 7 0 1 ~ 7 0 4 (for DK8) and 7 0 1 ~
7 0 8 (for DK16). With some systems, you may have to dial either the
general group code (9), Least Cost Routing code (9), or a Line Group
code (8 1 ~ 8 4 for DK8; 8 1 ~ 8 8 for DK16), instead of a CO line number
access code.
If you dialed a CO line access code, you will hear dial tone after you
press the last digit of a valid account code or busy tone after you press
the last digit of an invalid code.
To Flash a CO Line:
1. Momentarily press (for about
1/2 second) the hookswitch.
2. Dial 4 5.
To Record a Forced Account
Code:
1. Lift the handset.
2. Dial a CO line number access
code.
3. Enter the Forced Account
Code.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-9

4. Dial the telephone number.
To Record a Voluntary Account
Code:
1. After accessing a CO line or
while talking on a line, flash
the hookswitch.
2. Dial 4 6.
3. Enter the Voluntary Account
Code.
If you dialed 9, you may not hear dial tone. Continue dialing the
telephone number after you dial the account code.
EMERGENCY OVERRIDE OF FORCED ACCOUNT CODE DIALING
Forced Account Code requirements can be bypassed by three
emergency numbers, including 911. See your system administrator for
these numbers:
1) 911 2) ________ 3) ________
VOLUNTARY ACCOUNT CODES
Voluntary Account Codes are optional and can be entered anytime after
accessing a CO line or during a call.
“Flash the hookswitch” by depressing the hookswitch (plunger) located in
the handset cradle for about 1/2 second. (Some telephones may have a
special button which flashes the hookswitch when pressed.)
You will hear intercom dial tone; the CO line will be on Hold.
You will hear CO dial tone after dialing 46, or if you were talking, the
speech path to you is reconnected in one direction only so that the
outside caller cannot hear you or the account code entry but you can still
hear the outside caller.
If dialing a Verified Account Code, you will hear one confirmation burst
tone if you dial a valid number. If you dial an invalid code, you will hear
two burst tones. (Repeat Steps 1 ~ 3 to try again.)
If you enter the code after accessing a CO line, you will hear CO line dial
tone after entering the code. If you enter the code while talking, the
speech path will be restored in both directions after you enter the code.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-10

CO dial tone will stop after you dial the first digit of the telephone number.
Voluntary account codes must be entered before the call is disconnected.
VERIFIED ACCOUNT CODES
Some STRATA DK systems require that specific codes (called Verified
Account Codes) set in system memory must be entered when inputting
Forced or Voluntary Account Codes. If the system does not require
Verified Account Codes, any sequence of numbers can be entered when
inputting Account Codes, as long as the number of digits matches a
length established in system programming.
MESSAGE WAITING INDICATION
After reaching a busy or unanswered digital or electronic telephone, you
can set a Message Waiting Indication on the called telephone. A flashing
LED at the called telephone will indicate that a call is waiting. The station
user can press the button associated with the flashing LED to call you
back.
The Message Waiting Indication will be set at the station.
You will hear busy tone if the called station is busy, or you will hear
repetitive ringing or a single tone if the called station is idle.
The Message Waiting Indication on the station will be turned off.
4. Dial a telephone number if
you entered the code after
accessing the CO line.
. . . or . . .
Resume talking or hang up if
you entered the code while
talking.
To Set a Message Waiting
Indication:
1. If a called digital or electronic
telephone station is busy or
unanswered, dial 7.
2. Hang up.
To Cancel the Message Waiting
Indication:
1. Lift the handset and dial the
station number on which you
left the indication.
2. Dial 7 7.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-11

To Initiate a Busy Override
Signal:
1. After reaching a busy station,
dial 2.
To Initiate a Do Not Disturb
Override Signal:
1. After reaching a Do Not
Disturb station, dial 2.
To Initiate Executive Override:
1. After reaching a busy station,
dial 3.
OVERRIDE CALLS
Busy Override allows you to send a tone to a busy station to indicate that
a call is waiting, and Do Not Disturb Override lets you send a tone to an
idle station in the Do Not Disturb mode to indicate that a call is coming in.
Executive Override enables you to enter an established conversation.
Executive Override and Do Not Disturb Override are optional features
enabled in system programming. Any station can initiate Busy Override.
After you dial 2, a tone signal will be heard at the busy station, indicating
that a call is waiting.
If the Off-hook Call Announce option is installed on the busy station, then
you may talk.
After you dial 2, a tone signal will be heard at the Do Not Disturb station,
indicating that a call is coming in.
Your station must be enabled in system programming to initiate a Do Not
Disturb Override signal.
After you dial 3, you will enter the conversation. An optional tone signal
may be heard by the called parties prior to your entrance.
Your station must be enabled in system programming to initiate
Executive Override.
PAGING
You can make page announcements to digital and electronic telephone
speakers and external speakers.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-12

You will hear intercom dial tone.
These codes will allow a page to the speakers of telephones in Station
Page groups A, B, C, D or the All Call Page group.
Dial 3 5 for Zone A, 3 6 for Zone B, 3 7 for Zone C, and 3 8 for Zone D.
REPEAT LAST NUMBER DIALED
This feature enables you to automatically redial the last number called
with the touch of a button.
You will hear intercom dial tone.
The system will automatically dial the last telephone number you dialed.
To Page:
1. Lift the handset and access
the intercom.
2. Dial one of the following page
access codes:
3 0 = All Call
3 1 = Station Group A
3 2 = Station Group B
3 3 = Station Group C
3 4 = Station Group D
3 9 = All Call
3 5 ~ 3 8 = External Page
Zones (A ~ D)
3. Make your announcement in
a normal voice level and then
repeat the announcement.
4. Hang up when you have
completed your
announcement.
To Redial the Last Number
Dialed:
1. Lift the handset.
2. Dial the # button.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-13

SPEED DIAL
Speed Dial enables you to call telephone numbers by dialing a brief
access code, instead of having to dial the entire telephone number.
There are two types of Speed Dial numbers. Station Speed Dial numbers
are assigned by individual station users to their own station and can only
be dialed at their station. System Speed Dial numbers are assigned only
by Station 10 (typically the system administrator's or operator's station),
but can be used by other stations.
You will hear intercom dial tone after you lift the handset.
You will hear a short tone after you dial 6 6.
Station Speed Dial number access codes are 1 0 ~ 4 9.
CO line number access codes are 7 0 1 ~ 7 0 4 (for DK8) and 7 0 1 ~
7 0 8 (for DK16). With some systems, you may have to dial either the
general group code (9), Least Cost Routing (LCR) code (9), or a Line
Group code (8 1 ~ 8 4 for DK8; 8 1 ~ 8 8 for DK16), instead of a CO line
number access code.
The number can be up to 20 digits, including the CO line access code.
You will hear confirmation tone. The CO line access code and the
telephone number will be stored and will be dialed when you dial the
Speed Dial access code.
Repeat this procedure to replace the stored telephone number with a
new one.
You will hear intercom dial tone after you lift the handset.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-14
To Store a Station Speed Dial
Number:
1. Lift the handset.
2. Dial 6 6.
3. Dial # *.
4. Enter the access code (1 0 ~
4 9) where you wish to store
the telephone number.
5. Dial the CO line number
access code to be stored.
6. Enter the telephone number.
7. Dial #.
To Make a Call with a Station or
System Speed Dial Code:
1. Lift the handset.

You will continue to hear intercom dial tone.
Station Speed Dial codes are 1 0 ~ 4 9, and System Speed Dial codes
are 6 0 ~ 9 9. (Dial tone continues as you dial the access code.)
The system will automatically dial the telephone number assigned to the
access code.
TONE/VOICE FIRST SIGNALING
Your STRATA DK system may be set for Tone Signaling or Voice First
Signaling as the standard intercom call signaling method for calls to
digital and electronic telephones. The Tone Signal consists of repetitive
ring tones, while the Voice First Signal consists of a tone burst followed
by the caller's voice. When you initiate a call, you can change to the
alternate signaling method. Standard telephones always ring with Tone
Signaling, no matter what the system signaling method.
If the signaling mode is set for Voice First Signaling, you will hear a
single tone burst. If the signaling mode is set for Tone Signaling, you will
hear repetitive ringback tone.
The call will begin to ring at the station, if you changed from Voice First
Signaling to Tone Signaling.
If you changed from Tone Signaling to Voice First Signaling, the call will
stop ringing and you will hear a tone burst. You can converse after the
tone burst.
CO LINE QUEUING
CO Line Queuing enables you to be placed in a waiting queue for a CO
line after dialing a line group in which all lines are busy. You will be called
back when a line in the group becomes available.
2. Dial *.
3. Dial the 2-digit Speed Dial
access code.
To Change the Signaling Mode:
1. Call a digital or electronic
telephone via intercom.
2. To change the mode, dial 1.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-15

To Set CO Line Queuing:
1. If all outgoing lines are busy,
you will hear busy tone after
dialing a CO line access
code.
2. Dial 4.
3. Hang up.
4. Your telephone will ring at a
fast rate when a CO line
becomes idle.
5. Lift the handset immediately.
6. Dial the desired telephone
number.
To Cancel CO Line Queuing:
1. Lift the handset and dial 4 3.
To Use Call Pickup:
1. Lift the handset and dial 5.
2. Station—Dial a Station
number to pick up a call that
is ringing in at or on hold at
the station.
. . . or . . .
The busy tone will stop when you dial 4. You will hear dial tone for two
seconds, then the busy tone will resume.
You may make other calls while waiting for a line to become available.
Answer within two rings to prevent the callback from being cancelled.
You will hear CO dial tone. (If you hear busy tone, it means the line has
already been seized or has received an incoming call. Your request is not
cancelled. You will be called again the next time a line becomes idle.)
If the original call was made using Least Cost Routing (LCR) by dialing 9,
the telephone number will be automatically dialed in Step 4.
CO Line queuing will be cancelled.
CALL PICKUP
You can pick up a call that is ringing another station, a call placed on
hold at another station, and other types of calls.
You will be connected to the call ringing in or the held call.
STRATA DK STANDARD TELEPHONE FEATURE OPERATION
1-16