Total gym Ultimate User manual

U.S. Patents #D 405,132, #5,967,955; ROC Patent #ND-060792; PRC Patent #ZL 97 2 28552.0.

No part of this booklet may be reproduced or utilized in any form, by any means, electronic,

mechanical or otherwise, without the express written consent of the copyright holder.

1/14/10

Dedication to Quality

We warrant this product to be free from all

defects in material and workmanship when used

according to the manufacturer’s instructions.

See Limited Warranty Card for details.

Save your sales receipt.

(You may wish to staple it into this manual.)

OWNER’S MANUAL

For Maximum Effectivene

and Safety, Plea e Read

Thi Owner’ Manual

and view the Video

Before U ing Your

Total Gym®Ultimate.

5. a. Release Spring Loaded Pin (on left side rail) as shown.

b. Fold Vertical Column down towards the center of the unit.

c. Then insert Safety Hitch Pin at bottom of vertical column.

6. Slide the Glideboard towards the bottom of unit shown in Figure 6.

7. With caution, to avoid pinched fingers or hands, grab the top of the

Glideboard and slowly pull the unit up allowing the rollers to bring the

back of the unit towards the center. eep approximately 12” apart.

8. Continue to fold the exerciser together until it is completely folded

and roll the exerciser into a closet for storage.To store under a bed,

simply lower the exerciser to the floor and roll under the bed.

Do not store unit in upright position when folded.

TO REMOVE THE GLIDEBOARD

You can also remove the Glideboard if you need to fit the exerciser under a narrow

space (between 6” and 8”).

IMPORTA T: The Glideboard weighs approximately 20 lbs. Use caution when

lifting it off of the exerciser. Lifting incorrectly may result in user injury.

1. With exerciser laying flat on the floor, disconnect the pulley from the

hook on the underside of the Glideboard.

2. Next, tilt up the Glideboard and slide it off the frame

of the exerciser. When the bench is completely off

the exerciser, set it aside.

3. Next, pull the Spring Loaded Pin to release the Rail

and fold the exerciser together as shown above in

Figure 7. & 8. Be sure you release the Spring Loaded Pin

before folding.

— 12 —

12”

Back

Crossbar Front

Crossbar

Safety

Hitch Pin

Spring

Loaded

Pin 5b.Fold

Vertical

Column

down

5a.

5c.

7. & 8.

CRUSH HAZARD, KEEP HANDS CLEAR DURING FOLDING.

WARNING

Lift Here

Congratulations on purchasing your new

Total Gym®Ultimate.

With this product in your home, you have everything you need to start your own workout program, to

tone and strengthen the important muscle groups of your upper and lower body.This is vital for all of us,

regardless of age, sex, or fitness level, and regardless of whether your primary goal is body sculpting,

weight loss, health maintenance, or more energy for daily activities.

Strength training not only tones and conditions the muscles we use every day to stand, walk, lift, and

turn; it can actually transform our body composition. By reducing body fat and increasing the proportion

of lean muscle in our bodies, strength training can effectively turn up our metabolic thermostat, so that

we burn calories all the time, no matter what we’re doing.

It’s easy-all you have to do is spend 15 to 20 minutes a day, 3 to 4 days per week on your Total Gym®

Ultimate to start realizing the benefits.

Be sure to read through this Owner’s Manual carefully. It is the authoritative source of information

about your Total Gym®Ultimate.

If you have questions about your Total Gym®Ultimate, please call Customer Service at

1-800-321-9236, Monday through Friday, 8:30am to 6:00pm, EST.

Please do not call the above number for Parts. See Ordering Replacement Parts section below.

ORDERI G REPLACEME T PARTS

When ordering parts, please contact our Parts Department, toll free at 1-800-497-5831, Monday

through Friday, 8:30am to 6:00pm, EST.

IMPORTA T: You must have your serial number and this manual ready when calling for parts.

Serial #: ____________________________

Please also provide the following information:

1) Name, Mailing Address and Telephone Number

2) Date of Purchase

3) Where Product was Purchased (Name of Retail Store, City)

4) Model Number (21850-3)

5) Part Order Number and Description

TABLE OF CONTENTS

Equipment Warning/Caution Labels . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . .3

Set Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9

Starting Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Inspection, Maintenance & Storage . . . . . . . . . .11-12

Parts List & Exploded View . . . . . . .Inside Back Cover

— 11 —

INSPECTION, MAINTENANCE & STORAGE

I SPECT YOUR TOTAL GYM®ULTIMATE PRIOR TO EACH USE

Before using your Total Gym®Ultimate for your workout session, be sure to make the

following inspection:

• Make sure the equipment is fully opened and sitting on a solid, level surface with plenty

of clearance on all sides. Unit should be used on a mat or on carpeted surfaces only.

• Make sure all the Hitch Pins are securely in place and locked into position.

• Check that the Pulley is attached securely to the loop on the top underside of the Glideboard.

• Check that the Cables are traveling correctly in the groove of each pulley.

• Make sure the Cable is securely fastened to each Handle.

• Check that the Pilates Bar, Wing Accessory or other accessories are installed correctly

when in use.

• Make sure the Glideboard is gliding smoothly along the frame.

ROUTI E MAI TE A CE

• Wipe down your Total Gym®Ultimate on a regular basis using a clean cloth and alcohol

or alcohol-based products like Windex®or 409®. Do not leave towels or workout clothing

laying or hanging on the equipment.

• Periodically check the following parts for signs of fraying or other wear: the cable, pulleys,

wheels, Glideboard, accessories and frame. If the cable, pulleys, frame or wheels need

replaced - do not use your unit, wait until the part is replaced. If any other part than the

ones listed above needs to be replaced, do not use that part until it is replaced.

• Never use a lubricant such as WD-40®or ArmorAll®to lubricate or clean the unit. Use only

3-in-1®oil or machine oil to lubricate the axles of the wheel or pulley, not the roller surface.

TO STORE YOUR TOTAL GYM®ULTIMATE

Follow these easy steps to store your exerciser properly:

1. First, remove all accessories and attachments including the Flip Chart accessory and

replace the cap on the top of the Vertical Column.

2. Remove Safety Hitch Pin and Safety Pin from Vertical Column.

3. Be sure the Cable Pulley is attached to the underside of the Glideboard for folding.

4. Position one hand on either side of rail to hold it up before releasing the Height Adjustment

Quick Release Pin. Pull pin out and slowly lower the rails to the ground until they rest on

the back crossbar.

—2—

Continued on next page

Before beginning this or any exercise program, consult a physician or health professional, who can assist you in planning a

program appropriate for your age and physical condition. This is especially important if you are over age 35 or have pre-existing

health problems.

Do not overexert yourself. Stop exercising immediately and consult your doctor if you experience pain or tightness in

your chest, irregular heart beat, shortness of breath, or if you feel faint, nauseous, or dizzy.

This product is designed for home use only. It is not intended for commercial or institutional use. Use only as instructed. Do not

stand on the product.

The Total Gym

is not intended for use by children.eep this and all fitness equipment out of the reach of children.

Keep fingers, loose clothing, and hair away from moving parts.

Inspect your exerciser before each use to ensure proper operation.

Do not use this equipment unless all moving parts, including

cables and pulleys are working properly. See pages 11 &12 for details on Inspection, Maintenance and Storage.

The exerciser should only be used on a mat or carpeted surface to prevent unexpected movement of the unit.

Use only the accessory items recommended by the manufacturer.

To avoid serious injury, care should be taken at all times when getting on and off this or any exercise equipment.

EQUIPMENT WARNING/CAUTION LABELS

See page 3 for placement of the following warning/caution labels on your unit.

WARNING LABEL 1

FAILU E TO EAD AND FOLLOW THE

SAFETY INST UCTIONS STATED IN

THE OWNE ’S MANUAL AND VIDEO

MAY ESULT IN POSSIBLE SE IOUS

INJU Y O DEATH. KEEP CHILD EN

AWAY. MAXIMUM USE WEIGHT

275 LBS. EPLACE THIS LABEL IF

DAMAGED, ILLEGIBLE O EMOVED.

CLASS HC. GO TO OU WEBSITE:

WWW.FITNESSQUEST.COM O

CALL CUSTOME SE VICE:

1-800-497-5831 FO EPLACEMENT

LABEL, MANUAL, VIDEO

O QUESTIONS.

WARNING

WARNING LABEL 2

WARNING

MAKE S RE ADJ STMENT

PIN IS LOCKED IN PLACE

BEFORE BEGINNING

EXERCISES.

WARNING

BEFORE SING,

INSERT SAFETY PIN IN

FIRST HOLE BELOW

HEIGHT BRACKET.

WARNING LABEL 3

CR SH HAZARD

Keep hands clear

during folding.

WARNING

WARNING LABEL 4

(3 locations)

WARNING LABEL 5

(for Leg Pulley Bracket)

WARNING

WARNING LABEL 6

(4 locations)

KEEP HAIR, FINGERS, LOOSE CLOTHING, PETS,

AND CHILDREN AWAY FROM HINGES AND OTHER

MOVING PARTS TO AVOID SERIO S INJ RY. ALSO,

BE S RE TO HAVE ALL PINS LOCKED IN PLACE

BEFORE GETTING ON YO R TOTAL GYM®TO

AVOID SEVERE INJ RY.

CA TION

CAUTION LABEL 2

CA TION

REMOVE WING ATTACHMENT

FROM FRAME WHEN NOT

REQ IRED FOR THE

SPECIFIC EXERCISE.

CAUTION LABEL 1

(for Wing Attachment)

BE CAREF L NOT TO B MP

HEAD WHEN LEG ATTACHMENT

IS IN PLACE. REMOVE LEG

ATTACHMENT FROM FRAME

WHEN NOT REQ IRED

FOR THE SPECIFIC EXERCISE.

WARNING

MAKE S RE HITCH PINS ARE

LOCKED IN PLACE BEFORE

BEGINNING TO EXERCISE.

WARNING LABEL 7

(Located on back of Squat Stand)

CA TION

REMOVE SQ AT STAND FROM

FRAME WHEN NOT REQ IRED

FOR THE SPECIFIC EXERCISE.

CAUTION LABEL 4

(Located on back of Squat Stand)

CA TION

REMOVE PILATES BAR FROM

FRAME WHEN NOT REQ IRED

FOR THE SPECIFIC EXERCISE.

CAUTION LABEL 5

(Located on Pilates Bar)

CA TION

REMOVE DIP BAR FROM

FRAME WHEN NOT REQ IRED

FOR THE SPECIFIC EXERCISE.

CAUTION LABEL 6

(Located on both Dip Bars)

CA TION

REMOVE AB CR NCH

BOARD FROM FRAME WHEN

NOT REQ IRED FOR THE

SPECIFIC EXERCISE.

CAUTION LABEL 3

(Located on Ab Crunch Boards)

WARNING

PINCH POINT. KEEP HANDS

AWAY FROM THE FENDER.

SAFETY INSTRUCTIONS

STARTING OUT

Wear athletic shoes and comfortable light clothing when exercising on the Total Gym®Ultimate. Do not

exercise barefoot. Check your exerciser before using to ensure that all the parts are in place and working

properly (see pages 11 and 12 for details on Inspection, Maintenance and Storage).

Adult supervision is required at all times.

NOTE: The Rails and Glideboard can be raised to any desired level on the Height Adjustment

Column depending upon your degree of fitness. Please note, however, that the Rails

cannot be raised to the highest position on the Height Adjustment Column when the

Leg Pulley Bracket is attached to the column.

Be sure you have plenty of free space around the exerciser so that performing on

the Total Gym®Ultimate, as well as getting on and off, is convenient and safe.

Each time you raise or lower the Adjustment Column, be sure you hold it to keep it from

dropping to the floor.

Begin using the product at a low incline. As your fitness level progresses, increase the incline to increase the

intensity and improve your muscle strength. Don’t be in a hurry to exercise at a high intensity level; start out

easily and build gradually.The Total Gym®Ultimate is as easy as 1-2-3 to use, so read on.

1. Important Things to Remember When Using the Total Gym®Ultimate

• Always have control of the Glideboard before getting on and off the exerciser.

• eep your feet on the floor when getting on and off the exerciser. Only remove

them from the floor for the duration of the exercise.

• If you are using the handles, hold onto them as you get on and off the Glideboard.

2. Exercising with the Handles Only

Grasp the handles which are attached to the cable and slide the Glideboard to a position

in which you can comfortably sit or lay down when performing the desired exercise (see

the Exercise Guide). Be sure to keep your feet on the floor until you are in the correct

position for the specific exercise.Then, if the exercise calls for your feet to be off the

floor, place your feet as specified in the instructions.

3. Exercising with the Wing Accessory and the Dip Bars

Slide the Glideboard to a position in which you can comfortably sit or lay down on when

performing the desired exercise (see the Exercise Guide). eep your feet on the ground

until you are in the correct position and feel comfortable.Then, place your feet in the

proper position and begin to exercise.

When starting your exercise program, begin with the basic exercises in the Exercise Guide included with

your Total Gym®Ultimate to familiarize yourself with the movements. Use the lowest incline level to start

with- you can work up to a higher incline level in the weeks and months to come.

For the specific Total Gym®Ultimate exercises and programs, study and follow the instructions

in the Exercise Guide included with your product.

— 10 —

PRODUCT SPECIFICATIONS

— 3 —

Handles Glideboard

Bottom Rail

Top Inner Rail

Roller

Safety

Center Support Rail

Back Crossbar

Squat Stand

and

Pilates Bar

Leg Pulley Accessory Kit

Dip Bars

Wing Accessory

Vertical Column

Cap

Arm Pulley/Cable Assembly

Rope

Pulley/

D Ring

Assembly

1 Medium Hitch Pin

For use with leg pulley bracket.

2 Medium

Hitch Pins

Clips

Foot

Harness

TOTAL GYM®ULTIMATE SPECS.

LENGTH: folded: 51”

in use: 93”

HEIGHT: folded: 9”

in use: 44 1/2”

Leg Pulley Bracket

For use with leg pulley

accessory only.

Allen

Wrenches Stopper

Flip Chart Base

Foam Pad

Grips

Includes

2 Workout DVDs

Roller

Cap

Safety

Hitch Pin

Spring Loaded Pin

(Located on Side of Rail)

Height Adjustment Tube

Height Adjustment

Quick Release Pin

Arm Pulley/Cable Hook

(Attaches to loop underneath Glideboard)

Miscellaneous

Items shown below are also in

Leg Pulley Accessory Kit

WARNING

LABEL 1

WARNING

LABEL 2

WARNING

LABEL 3 WARNING

LABEL 4

WARNING

LABEL 6

CA TION

LABEL 2

WARNING

LABEL 5

CA TION

LABEL 1

WARNING

LABEL 4

Flip Chart/Water

Bottle Holder

10mm & 13mm

Hex Wrench

M8 x 60mm

Hitch Pins

Ab Crunch Boards

CA TION

LABEL 3

2 Short

Hitch Pins

WIDTH: 16”

WEIGHT: 62 lbs.

MAX. USER WEIGHT: 275 lbs.

CA TION

LABEL 6

WARNING

LABEL 7

CA TION

LABEL 4

CA TION

LABEL 5

Squat Stand and

Pilates Bar

WARNING

LABEL 7

CA TION

LABEL 4

3 - M8 x 110mm

Hitch Pins

CA TION

LABEL 5

HOW TO ATTACH THE LEG PULLEY ACCESSORY KIT

1. Connect the Leg Pulley Bracket to the top of the Vertical Column by

aligning Bracket with the hole at the top of the column. (Be sure

bracket is right side up.) Insert Long Hitch Pin through the hole to

secure Bracket onto the Vertical Column.

2. Detach the Cable Assembly from the loop on the underside of the

Glideboard, attach one of the Clips from the Leg Pulley Assembly.

3. Place D-Ring on Pulley first.Then connect the D-Ring to the

Bracket as shown.

NOTE: If rope appears to be twisted, take D-Ring off and turn

Pulley around.

4.Attach the Foot Harness to one of your feet by placing your foot in

the Harness so the sewn-in O-ring is on the bottom of your foot.

Pull tightly on the strap at the Harness Buckle so the Foot Harness

is secure.

5.(a) Position yourself on the Glideboard correctly for the specific

exercise you want to perform.

(b) While sitting down on the Glideboard, bring 1 knee up, connect

the Clip on the end of the rope to an O-Ring on the Foot

Harness attached to your foot. Depending on the exercise you

are performing, connect the Clip to the proper O-Ring. Be sure

to always stabilize the Glideboard when clipping on or off the

Harness. Also, use caution when getting on or off the Glideboard.

You are now ready to exercise using the Leg Pulley Accessory.

See your Exercise Guide for specific exercises that utilize the

Leg Pulley Accessory.

OTE: Remove Leg Pulley Bracket when you are not exercising with it.

the Harness. Be sure to stabilize Glideboard when disconnecting Foot Harness.

TOP VIEW

Left Foot

Right Foot

— 9 —

TOP VIEW

Left Foot

Right Foot

TOP VIEW

Left Foot

Right Foot

Foot Harness

Harness

Buckle

Clip

O-Ring (loose)

O-Ring (sewn in)

O-Ring (loose)

5b.

Leg Pulley Accessory Kit

Rope Pulley/D Ring

Assembly

Clip

Long

Hitch

Clip

Harness

Leg Pulley Bracket

For use with leg pulley

accessory only.

Bracket

D-Ring

Long Hitch Pin

Pulley

SET UP

Your product comes with:

• Safety Hitch Pin located at the bottom of the Vertical Column, which must be removed prior to unfolding.

• Height Adjustment Quick Release Pin located on back of Vertical Column for raising and lowering rails.

• One (1) Spring Loaded Pin locked into the base of the left rail by the Height Adjustment Tube. Left side is determined

by standing behind the unit facing the Vertical Column.

IMPORTA T: To Prevent Injury – Be sure the Spring Loaded Pin is locked securely into place in the left

rail before using unit. This will prevent the Height Adjustment Column from falling forward.

• Safety Pin - located on Lanyard/attached to Height Adjustment Tube.

• One Medium Hitch Pin for Leg Pulley Bracket, two Medium Hitch Pins for the Wing Accessory, two Short Hitch

Pins for the Dip Bars, two Short Hitch Pins for the Ab Crunch Boards and three Long Hitch Pins for the Squat

Stand/Pilates Bar.

IMPORTA T: Before using the Wing Accessory, Leg Pulley Accessory and Dip Bars, be

sure the Hitch Pins are securely inserted (see pages 6 - 9 of this manual for directions).

1. Pull the product out of the shipping box. Remove all packaging

materials, including tape and cardboard inserts, from your unit.

2. Lay product on the floor with Glideboard side up. Make sure you have

plenty of space on both ends of the product. Slide the Glideboard as far

as it will go towards the Front Crossbar before you begin lifting unit.

3. Lift the exerciser up by holding it at the top of the rails. Using your foot,

slowly spread the unit open at the bottom approximately 12 inches so

that it rests firmly on the Front and Back Crossbars not allowing it to

go too far.

4. Make sure the handles are out to the sides before

you begin to unfold your unit. eep hands and

fingers away from pulley. Hold onto the top center

of Glideboard and begin rolling rear rollers. Spread

the unit out until it is flat on the floor. Be careful to

do this slowly.

Be sure to support the frame in the center to

avoid having the product drop suddenly onto

the floor or pinch fingers.

5. (a) Remove Safety Hitch Pin from bottom of Vertical

Column. Next remove plastic packing ties from the top

and bottom of the Vertical Column. Pull out the Spring

Loaded Pin nob located at the left rail to release

Spring Loaded Pin. Continue to hold pin out while

performing the next step.

— 4 —

12”

Back

Crossbar Front

Crossbar

Safety Hitch Pin

Quick

Release Pin

Spring Loaded Pin

Lift Here

Hold Here While Lowering

To The Ground

Rear Rollers

HOW TO ATTACH THE AB CRUNCH BOARDS (b) Take hold of the Vertical Column and pull it up until it is upright. Release

the Spring Loaded Pin. You should hear it lock back into place.

IMPORTA T: Be sure the Spring Loaded Pin is locked into place

before using your unit. You will know the pin is locked into place

when you can see the end protrude through the inside of the rail bracket.

6. Position one foot on Back Crossbar to keep the product from lifting

off the floor. With one hand on either the right or left rail and the

other hand holding the Height Adjustment Quick Release Pin out, slide

the rails along the Vertical Column to desired position and release pin.

Pin will pop into place - you will hear a snap. Then turn knob to the

right to tighten and secure. Last, insert straight Safety Pin (attached

to the Height Adjustment Tube) into the hole on Vertical Column

just below the Height Adjustment Bracket.

NOTE: Insert Safety Hitch Pin in the side hole located

at the bottom of the Vertical Column.

(This is the pin you removed in step 5a).

7. STOPPER ASSEMBLY

If the Stopper at the bottom of the Vertical Column has not already been

installed, please do so now. Locate the Stopper which is packed in Miscellaneous

Accessories (See Product Specifications on page 3 of this manual). Unscrew nut

on the end of the Stopper and remove. Insert the Stopper into the hole located in

the center of the Back Crossbar. (See Fig. 1) Screw the nut back onto the Stopper

and tighten with Allen Wrenches provided. (See Fig. 2)

IMPORTANT: Proper installation of the Stopper is necessary for the Rollers to

function easily when the unit is folded and rolled into place for storage.

8. FLIP CHART/WATER BOTTLE HOLDER ASSEMBLY

1. Insert the Flip Chart Stand into the Vertical

Column then insert the Flip Chart/Water

Bottle Holder into the Flip Chart Stand.

You will hear it snap into place. See Fig. 1

2. Insert Water Bottle into holder. Be sure to

wash the Water Bottle in hot soapy water

prior to use. Rinse thoroughly. See Fig. 2.

Height Adjustment

Quick Release Pin

Put Safety Hitch Pin

Back Into Hole

F g. 2

F g. 1

1. Locate the 3 holes at the top of the Right

and Left Rails on the Vertical Column

(see Fig. 2a). DO NOT use hole closest

to the Vertical Column. Your head could

come in contact with the Vertical Column

and could result in possible serious injury

or death.

Choose the 2nd or 3rd hole depending

on your height or comfort level.

2. Install the Ab Board labeled (L) onto the

Left side Rail with the Handle facing toward

the Vertical Column (see Fig 2b).

3. Insert the M8 x 60mm Hitch Pin through the

holes on the Attachment Brackets and through

the hole on the Left Rail as indicated by arrow.

4. Repeat for right Ab Board.

Fig. 1

Fig. 2b

ASSEMBLY

1. Remove Hex Bolts and Washers from bottom of Ab Boards.

2. With the small end of the Ab Board closest to you, securely

attach the appropriate Handle with 4 Flat Washers, Spring

Washers and Hex Bolts with Hex Wrench provided. See Fig 1.

3. Repeat on 2nd Ab Board. M8 Flat Washer

Ab Board

Handle Grip

Handle

M6 Spring Washer

M6 x 20mm Hex Bolt

Vertical

Column Handle facing

toward Vertical Column

Left Rail

Hitch Pin

Fig. 2a

Left Rail

Right Rail

DO NOT use hole closest

to Vertical Column

Vertical

Column

IMPORTA T SAFETY I STRUCTIO S:

1. Be sure to give enough clearance so your head does not hit the Vertical Column when performing these

exercises. DO OT attach the Ab Crunch Board to the Rail on the hole that is closest to the Vertical

Column, doing so could result in possible serious injury or death.

2. Remove Leg Attachment Bracket when using the Ab Crunch Board to avoid contact, which could result in

possible serious injury or death.

3. Be sure that the Hitch Pins are securely locked in place before using the Ab Crunch Board. Failure to do so

may cause the Ab Crunch Board to fall off resulting in possible serious injury or death.

4. Do not move your body to the extreme left or right when using the Ab Crunch Board to avoid falling off the

exerciser which could result in possible serious injury or death.

5. Caution should be used when getting on and off the exerciser when the Ab Crunch Board is in place. Failure

to do so could result in possible serious injury or death.

F g. 1

F g. 2

Flip

Chart

Stand

Vertical

Column

Flip Chart/

Water Bottle

Holder

— 5 —— 8 —

Attachment

Bracket

I STALLATIO - How to Install the Ab Crunch Boards to your Total Gym®

FRO T PRESS

1. Locate the holes at the bottom of the right and left rails near the front crossbar.

2. With the wing angled toward the glideboard, line up the brackets on the wing with the

desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the Wing Accessory brackets and

the hole on the rails, as shown in Figure 5.

4. You are now ready to perform the Front Press which works the upper chest and triceps.

See your Exercise Guide for specific exercises.

F g. 5

Dip Bar Hole

1. and 2. Dip Bars

Hitch Pin

HOW TO ATTACH THE WING ACCESSORY

The Wing Accessory provided with your unit has been uniquely designed to serve several purposes. It can be

placed at the top or bottom of the exerciser and angled toward you or away from you depending upon what is

comfortable for you.

Two thick Foam Pads are provided with the Wing Accessory. They must be attached to the wing (if not already)

before exercising. To do this:

1. Simply wet each end of the straight Crossbar of the wing

with some soapy water.

2. Then, attach Foam Pads on the Crossbar as shown in Figure 1. Let

dry before beginning to exercise with the Wing Accessory.

Proper ways to use the Wing Accessory in accordance

with the exercises you wish to do:

PULL UPS A D CHI UPS

1. Locate the holes at the top of the right and left rails.

2. With the wing angled toward the glideboard, line up the brackets

on the wing with the desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the wing

accessory brackets and the hole on the rails, as shown in Figure 2.

4. You are now ready to perform Pull Up and Chin Up exercises

to work the arms, lats and back. See your Exercise Guide for

specific exercises.

LEG PULL; CRU CHES A D SIT UPS

1. Locate the holes at the top of the right and left rails.

2. With the wing angled away from the glideboard, line up the

brackets on the wing with the desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the Wing

Accessory brackets and the hole on the rails, as shown in Figure 3.

4. You are now ready to perform leg pulls, crunches and sit up

exercises to work the abdominals, waist and legs. See your

Exercise Guide for specific exercises.

SQUATS (Pilates bar can be used instead of Wing accessory)

1. Locate the holes at the bottom of the right and left rails near the front

crossbar.

2. With the wing angled away from the glideboard, line up the brackets

on the wing with the desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the Wing

Accessory brackets and the hole on the rails, as shown in Figure 4.

4. You are now ready to perform the squats which works the thighs

and calves. See your Exercise Guide for specific exercises.

OTE: When performing the squat exercises, be sure to position your

hands on the side of the glideboard, NOT along the bottom of the

board in order to avoid pinched fingers.

F g. 2

— 6 —

F g. 3

F g. 4

F g. 4a

F g. 1

F g. 4b

HOW TO ATTACH THE DIP BARS

SQUAT STA D ASSEMBLY

1. Lay the Squat Stand, with the Foam Pad down, on the floor.

See Fig. 1.

2. Place the Pilates Bar into the indentation area. See Fig. 2.

3. Secure the Squat Stand to the Pilates Bar by fully inserting

the three Large Hitch Pins. (One on each side and one

through the top). See Fig. 3.

4. Locate the holes at the bottom of the Right and Left Rails on the Front

Crossbar. See Fig. 4a.

5. Insert Squat Stand with the Foam Pad facing the Glideboar into

holes – make sure it is all the way in before beginning. See Fig. 4b.

6. You are now ready to perform the squat exercises which work the

thighs and calves.

See your Flip Chart for specific exercises.

OTE: When performing the squat exercises, be sure to position

your hands on the side of the Glideboard, OT along the

bottom of the board in order to avoid pinched fingers.

1. Attach each Dip Bar to the frame with the Short Hitch Pins included

with your Total Gym®Ultimate. Note: Hitch Pins are included in

Miscellaneous Parts. Simply line up each bar with the holes in the

upper portion of the bottom frame.

2. Slide one Short Hitch Pin through the hole of one of the

Dip Bars and through the frame. Repeat Steps 1 and 2

for attaching the other Dip Bar. Make sure to securely

attach each Dip Bar to each side of the frame before

using. See your Exercise Guide for specific exercise.

ote: Remove the Dip Bars when you are not

exercising with them.

Dip Bars 2 Short

Hitch Pins

— 7 —

F g. 3

F g. 2

Large Hitch

Pins

Front

Crossbar

PILATES BAR ASSEMBLY

1. Assemble the Pilates Bar at the opposite end of the unit by

inserting it into the Front Crossbar as pictured to the right. Make

sure it is fully inserted.

IMPORTANT: Remove accessories from your equipment when not

required for a specific exercise.

F g. 1

HOW TO ATTACH THE PILATES BAR/SQUAT STAND ACCESSORY

FRO T PRESS

1. Locate the holes at the bottom of the right and left rails near the front crossbar.

2. With the wing angled toward the glideboard, line up the brackets on the wing with the

desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the Wing Accessory brackets and

the hole on the rails, as shown in Figure 5.

4. You are now ready to perform the Front Press which works the upper chest and triceps.

See your Exercise Guide for specific exercises.

F g. 5

Dip Bar Hole

1. and 2. Dip Bars

Hitch Pin

HOW TO ATTACH THE WING ACCESSORY

The Wing Accessory provided with your unit has been uniquely designed to serve several purposes. It can be

placed at the top or bottom of the exerciser and angled toward you or away from you depending upon what is

comfortable for you.

Two thick Foam Pads are provided with the Wing Accessory. They must be attached to the wing (if not already)

before exercising. To do this:

1. Simply wet each end of the straight Crossbar of the wing

with some soapy water.

2. Then, attach Foam Pads on the Crossbar as shown in Figure 1. Let

dry before beginning to exercise with the Wing Accessory.

Proper ways to use the Wing Accessory in accordance

with the exercises you wish to do:

PULL UPS A D CHI UPS

1. Locate the holes at the top of the right and left rails.

2. With the wing angled toward the glideboard, line up the brackets

on the wing with the desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the wing

accessory brackets and the hole on the rails, as shown in Figure 2.

4. You are now ready to perform Pull Up and Chin Up exercises

to work the arms, lats and back. See your Exercise Guide for

specific exercises.

LEG PULL; CRU CHES A D SIT UPS

1. Locate the holes at the top of the right and left rails.

2. With the wing angled away from the glideboard, line up the

brackets on the wing with the desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the Wing

Accessory brackets and the hole on the rails, as shown in Figure 3.

4. You are now ready to perform leg pulls, crunches and sit up

exercises to work the abdominals, waist and legs. See your

Exercise Guide for specific exercises.

SQUATS (Pilates bar can be used instead of Wing accessory)

1. Locate the holes at the bottom of the right and left rails near the front

crossbar.

2. With the wing angled away from the glideboard, line up the brackets

on the wing with the desired position holes on the rails.

3. Insert the 2 Medium Hitch Pins through the holes on the Wing

Accessory brackets and the hole on the rails, as shown in Figure 4.

4. You are now ready to perform the squats which works the thighs

and calves. See your Exercise Guide for specific exercises.

OTE: When performing the squat exercises, be sure to position your

hands on the side of the glideboard, NOT along the bottom of the

board in order to avoid pinched fingers.

F g. 2

— 6 —

F g. 3

F g. 4

F g. 4a

F g. 1

F g. 4b

HOW TO ATTACH THE DIP BARS

SQUAT STA D ASSEMBLY

1. Lay the Squat Stand, with the Foam Pad down, on the floor.

See Fig. 1.

2. Place the Pilates Bar into the indentation area. See Fig. 2.

3. Secure the Squat Stand to the Pilates Bar by fully inserting

the three Large Hitch Pins. (One on each side and one

through the top). See Fig. 3.

4. Locate the holes at the bottom of the Right and Left Rails on the Front

Crossbar. See Fig. 4a.

5. Insert Squat Stand with the Foam Pad facing the Glideboar into

holes – make sure it is all the way in before beginning. See Fig. 4b.

6. You are now ready to perform the squat exercises which work the

thighs and calves.

See your Flip Chart for specific exercises.

OTE: When performing the squat exercises, be sure to position

your hands on the side of the Glideboard, OT along the

bottom of the board in order to avoid pinched fingers.

1. Attach each Dip Bar to the frame with the Short Hitch Pins included

with your Total Gym®Ultimate. Note: Hitch Pins are included in

Miscellaneous Parts. Simply line up each bar with the holes in the

upper portion of the bottom frame.

2. Slide one Short Hitch Pin through the hole of one of the

Dip Bars and through the frame. Repeat Steps 1 and 2

for attaching the other Dip Bar. Make sure to securely

attach each Dip Bar to each side of the frame before

using. See your Exercise Guide for specific exercise.

ote: Remove the Dip Bars when you are not

exercising with them.

Dip Bars 2 Short

Hitch Pins

— 7 —

F g. 3

F g. 2

Large Hitch

Pins

Front

Crossbar

PILATES BAR ASSEMBLY

1. Assemble the Pilates Bar at the opposite end of the unit by

inserting it into the Front Crossbar as pictured to the right. Make

sure it is fully inserted.

IMPORTANT: Remove accessories from your equipment when not

required for a specific exercise.

F g. 1

HOW TO ATTACH THE PILATES BAR/SQUAT STAND ACCESSORY