Toto T60 User manual

SPECIFICATIONS
OPERATING CONDITIONS
S06595Z
TROUBLESHOOTING
URINAL FLUSH VALVE T60
CHECK
POINT
Water continue running 1 Remove and clean
Water leaks around the body 2, 3, 4 Tighten
PROBLEM
SOLUTION
A. STRAINER B. PISTON VALVE HOLE
T60P
Urinal Flush Valve
(Straight Pipe)
For U57, U57M
T60RN
Urinal Flush Valve
(Bended Pipe)
For U104
T60S
Urinal Flush Valve
(Bended Pipe)
For U370
35
14
Ø16
G½
Ø55
45
14
Ø16
G½
Ø55
Small Wire
Hole
Soft Brush
Water
Strainer
MAINTENANCE
INSTALLATION
1. PISTON VALVE
3. CAP NUT
2. COVER
4. CAP NUT
Packing
Nut
Pipe
1
2
3
Water Supply
Cover
Body
Valve
ATTENTION
Use Seal Tape
(Not Include)
R6
Ø16
75
14
G½
Ø55
Open the valve
1. Water supply pressure : 0.07 ~ 0.75 MPa.
2. Ensure that water supply is clean ( No Sand, Dirt, Etc.)
All Finishes : Clean the finish with mild soap and warm
water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as
ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning
Clean the Piston valve periodically with soft brush and
small wire.
1.
2.
1.
2.Don t use abrasive cleaners or solvents on faucets and fittings.
As the product model is constantly updated, the actual product
may not look the same as it shown in the diagram, but the
basic installation principles are the same.

SPESIFIKASI
KONDISI OPERASIONAL
S06595Z
PENYELESAIAN MASALAH
URINAL FLUSH VALVE T60
Air terus mengalir 1 Lepas dan bersihkan
Air bocor disekitar bodi 2, 3, 4 Kencangkan
MASALAH
SOLUSI
POIN
PERIKSA
A. STRAINER B. PISTON VALVE HOLE
T60P
Urinal Flush Valve
(Straight Pipe)
For U57, U57M
T60RN
Urinal Flush Valve
(Bended Pipe)
For U104
T60S
Urinal Flush Valve
(Bended Pipe)
For U370
35
14
Ø16
G½
Ø55
45
14
Ø16
G½
Ø55
Small Wire
Hole
Soft Brush
Water
Strainer
PEMELIHARAAN
PEMASANGAN
1. PISTON VALVE
3. CAP NUT
2. COVER
4. CAP NUT
Packing
Nut
Pipe
1
2
3
Water Supply
Cover
Body
Valve
PERHATIAN
R6
Ø16
75
14
G½
Ø55
Open the valve
1. Tekanan sumber air: 0.05 ~ 0.75 MPa.
2. Pastikan kondisi sumber air adalah bersih (tidak ada pasir,
kotoran dan lain lain)
1.
2.
Jangan gunakan pembersih atau pelarut abrasif pada faucet
dan fitting.
Karena model produk terus mengalami pembaharuan, aktual
produk mungkin tidak sama dengan gambar, tapi prinsip dasar
pemasangan adalah sama.
Gunakan Seal Tape
(Tidak disertakan)
Seluruh lapisan : Bersihkan lapisan akhir dengan sabun lembut
dan air hangat. Lap seluruh permukaan hingga benar-benar
kering dengan kain lembut yang bersih. Kebanyakan bahan
pembersih mungkin mengandung bahan kimia, seperti amonia,
klorin, pembersih toilet, dll. yang dapat mempengaruhi hasil
akhir dan tidak disarankan untuk membersihkannya
Bersihkan Piston valve secara berkala dengan sikat lembut
dan kawat kecil.
1.
2.