Toto TBV02401 User manual

1 2
Contents
Contents Detailed list
Detailed List
1
2
3
4
5
6-7
8
9
Contents…………………………………
Detailed list………………………………
Use condition and attentions in use……
Attentions in use and maintenance……
Temperature Adjustment………………
Dismantle and inspection………………
Product warranty card……………………
Main body of faucets
Temperature-adjusting handle
Open and close switching
handle
Decorating plate
Lining plate
Screw
Hex wrench
Instructions for construction
Instructions for operation
1 set
1 set
1 set
1 set
1 piece
4 pieces
1 piece
1 copy
1 copy
(※ Single thermostat product only has a temperature-adjusting handle).
The products using this detailed list include:
TVB01406* "G Shower" Concealed Thermostat Valve
(Standard Type)
TBV02401* "G Shower" Concealed Thermostat Valve
(Standard Type)
TVB01407* "G Shower" Concealed Thermostat and Volume
Control Valve(Standard Type)
TBV02403* "G Shower" Concealed Thermostat and Volume
Control Valve(Standard Type)
TVB01408* "G Shower" Concealed Thermostat and 2way
Diverter Valve with Shut Off (Standard Type)
TBV02404* "G Shower" Concealed Thermostat and 2way
Diverter Valve with Shut Off (Standard Type)

4
3
Use condition and attentions in use
Attentions in use and maintenance
Use condition
Attentions in use
！
！
！
Attentions
Maintenance
！
Warning
！
To maintain a beautiful appearance of the product, the user is requested to conduct maintenance and
care in the following method.
Wipe with a piece of soft cloth frequently and use a piece of soft cloth dipped in water to wipe from time
to time.
When dirt exists obviously, please use water to wash sufficiently after wiping with a neutral detergent.
Cold water supply*hot water supply pressure
Minimum pressure ………………… 0.05MPa (flow pressure)
Maximum pressure ………………… 1.0MPa (static pressure)
Recommended service pressure……0.1-0.5MPa (flow pressure)
It is required to provide a pressure-reducing valve when exceeding 0.5MPa.
Testing pressure………………………1.6MPa (static pressure)
The temperature for water supply is 4~90℃. It is suggested to use the temperature of
60℃. Do not use steam to supply hot water.
The ambient temperature for use is above 0℃. If the ambient temperature is lower than
0℃,the faucets will deform and crack from freezing.
To prevent internal sprinkler damage, the water outlet temperature on the sprinkler side
shall not exceed 60℃. It is suggested to use a temperature below 45℃.
Being out of use for a long time may result in internal and external rust to the faucets and
being unable to be used.
If you want to scrap this product, do not treat it as you do for general household garbage.
Please follow relevant statutes to have it treated, recovered and collected appropriately by
an independent recovery system.
The product in these instructions has a cleaning function.
※ To attain the best installation and operation effect, it is recommended that the faucet
should be used with the handheld series shower from TOTO.
1.
2.
3.
4.
5.
6.
7.
Warning: it means that ignoring this mark and misoperation may cause serious
personal injury and death.
Attention: it means that ignoring this mark and misoperation may cause personal
injury or property loss.
Children are not allowed to use or can use only under the custody of adult. Such special groups as
the aged and disabled should be accompanied by those with behavioral competence when using it.
The hot water supply side of the faucets is in a condition of high temperature. Do not allow skin to
contact with the hardware surface directly. Otherwise, scalding may occur.
Do not reverse cold*hot water pipes. Otherwise, scalding may occur.
Do not use steam to supply hot water. Otherwise, scalding may occur.
Rotate the temperature-adjusting handle slowly. If rotating the temperature-adjusting handle
rapidly, the temperature will rise and fall sharply.
When the safety button on the temperature-adjusting handle is aligned with the “40” marking on
the decorating plate in the center, the water outlet temperature is 40℃; when the
temperature-adjusting handle is turned anticlockwise (without depressing the safety button) until it
cannot be turned any longer, the water outlet temperature is about 42℃；After pressing the safety
button of the temperature-adjusting handle, continue to rotate anticlockwise until no rotation can
be made any longer. The water outlet temperature is about 45℃.
After using hot water, it is imperative for the temperature-adjusting handle to be below “40” to
avoid hot water spraying out when using again.
Please be sure to close the water inlet valve before removal and repair.
1
2.
3.
4.
5.
6.
As the temperature control cartridge is a precise component, do not dismantle it without
authorization. Otherwise, such poor conditions as water leakage, etc. may be caused.
Do not use a strong force to impact the faucet . Otherwise, water leakage or faucet strength
reduction may occur.
It is imperative to use a neutral detergent in cleaning. Other detergents than a neutral one may
damage the plating coat or make the surface discolor.
Do not use any such detergent as acidic detergent and abstergent, polishing powder, etc.
containing thick particles and nylon brush. Otherwise, the plating coat may be damaged, etc.
It is allowed to use a piece of soft cloth to wipe or use from time to time a piece of cloth immersed
in machine oil or vehicle wax to wipe. However, do not contact with resin components. Otherwise,
they may lose the gloss and become rusty.
It is suggested not to leave it unused for a long time. Otherwise, this may lead to internal and
external rust to faucets to such a degree that it cannot be used any more, etc.
With the product design being updated constantly, the physical object may not coincide with the
figure. However, the basic principle for installation, use is the same.
As a water supply inspection is made before leaving factory, there may be water remaining in the
faucet and this is not the problem of the product.
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
7.

“40”
About 40℃
Open and close switching handle
Hot water side
Temperature-adjusting handle
Temperature-
adjusting handle
Small screw
Handle cover
Button
Safety button
Cold water side
Water outlet temperature confirmation
Make the safety button on the temperature-adjusting handle and the “40” marking on
the panel aligned in the center. Rotate the switching handle to allow the water outlet
shower to output water. Confirm that the water outlet temperature is 40℃. If not, please
adjust the water outlet temperature by following the main points below. (Take TBV02404*
as an example. The main points thereof for water outlet temperature adjustment is the
same as that for thermostat product)
Main points of water outlet temperature adjustment
I. Characteristics
①Under the action of the thermostat
cartridge , the water coming out can be adjusted to a
certain temperature automatically. Therefore, even if the pressure of the cold, hot water
supplied changes, the temperature almost experiences no change.
②Just adjust the temperature-adjusting handle and the desired temperature can be
reached.
③A filter net is installed to avoid sand particles or dust in the pipe coming into the
component.
④The temperature-adjusting handle has a safety button. No hot water will spray out even
in case of misoperation.
II. Names and using methods of different parts
1. Allow the water outlet or shower to
output water. Rotate the
temperature-adjusting handle until the
water outlet temperature reaches 40℃.
That position has nothing to do with the
scale on the body. When rotating to the
high temperature side, please press the
safety button.
2. When pulling out the
temperature-adjusting handle, please
take out the handle cover first and then
screw to remove the small screws.
※ When removing the handle cover,
please use something with a thin
pointed end such as screwdriver, etc.
Take care not to scratch the plated coat
surface and do not allow the
temperature-adjusting handle to rotate.
3. Make the safety button on the
temperature-adjusting handle and the
“40” marking on the decorating plate
aligned in the center. Install the
temperature-adjusting handle. After
confirming that the water outlet
temperature is 40℃. , tighten the small
screws. Install the handle cover.
5 6
Temperature Adjustment Using method
1. Temperature adjustment
2. Safety button
3. Water outlet and water stop
Button
“40”
Open and close switching handle
Hot water side
Cold
water side
Temperature-adjusting handle
Safety button
Open and close switching handle
Hot water side
Temperature-adjusting handle
Safety button
Cold water side
① Rotate the temperature-adjusting handle and adjust the
desired water outlet temperature to the 40℃ marking.
The marking “40” represents the water outlet temperature
standard.
(The single thermostat faucet is the same as above in respect
of temperature adjustment.)
② A safety button is provided to avoid hot water spraying out
due to misoperation. The temperature-adjusting handle is fixed
around “40”. If high-temperature water outlet is wanted
(greater than 40℃ ), it is imperative to press the safety button
and rotate the handle simultaneously.
Attention: After using, it is imperative to have the handle return
to a level below 40 to avoid scalding when using next time.
③ When, taking the switching faucet as an example, matching
with a fixed water outlet and a fixed shower, water will come out
from the water outlet when the switching handle is turned
leftward to position “1” and water will come out from the fixed
shower when it is turned rightward to position “2”. When the
above rotation reaches the limit position, the water outlet
amount is maximal. To stop water outlet, please rotate the open
and close switching handle rod to the central position.
Attention: After using, it is imperative to have the handle return
to a level below 40 to avoid scalding when using next time.
Water outlet
Shower

78
Dismantle and inspection
Using method
Hot water side Cold water side
The spindle of
hot water stop valve
open open
The flow
becomes smaller
Handle cover
※ If shower bath flow is so small that influences shower bath comfort, the customer can remove
the check valve and clean the filter net.
Decorating plate
Lining plate
Open and close switching handle
Small screw
13. Sufficiently tightened?
Screw
5. Sufficiently tightened?
Snap ring Thermostat cartridge
Filter net
6. Any dust?
Check valve
7. Becoming loose?
Check valve, 7. Becoming loose?
Cartridge
10. Becoming loose?
O-ring
15. Any
scratch,
dirt?
Connector
Break
apparatus
O-ring
3. Damaged?
Screw, 8. Tightened?
Filter net cleaning and flow adjustment
Please be sure to clean the filter net after faucet installation. Besides, if the user finds
the flow to be insufficient after using for a period of time, please clean the filter net.
Filter net cleaning when clean the filter
net. Please turn off cold and hot water
supply valve then use a sleeve wrench
to remove the check valve in anti
clockwise direction.Clean the filter net
after carry out the check valve.
Flow adjustment
The flow of both hot water stop valve
and cold water stop valve reduces
during rotating clockwise and increases
during rotating anticlockwise.
Attention: When turning the water
stop valve spindle anticlockwise, take
care to use appropriate force.
Otherwise, the water stop valve may be
removed entirely resulting in water
The spindle of
cold water stop valve
The flow becomes bigger
Phenomenon
The water flow is small
The handle swing
The decorating plate swing
The water flows without stop and water leakage exists
Only high temperature appears
Only low temperature appears
Inspecting item
6, 7, 9
1, 2, 3, 11, 13, 14
5
6, 7, 8, 9, 10, 11, 12, 14, 15
4, 6, 7,9, 12
4, 6, 7, 9, 12
In case of any failure after installation, please remove by following the main points below.
(In case that it is required to remove those spare parts not removed in
this figure, please contact relevant after-sale service people for removal)
(Take TBV01407* as an example)
Filter net
9. Any dust?
Cartridge sleeve
11. Becoming loose?
Cartridge sleeve
14. Becoming loose?
O-ring
12. Any scratch, dirt?
Temperature-
adjusting handle
4. Temperature adjustment
appropriate?
Hex head screw
1 .Sufficiently tightened?
Small screw
2 .Sufficiently tightened?
！

9
TOTO Asia Oceania Pte. Ltd.
Telephone:[phone]
FAX: [phone]
Address：10 Eunos Road 8 #12-07 Singapore Post Centre
Singapore 408600
Website:asia.toto.com
TOTO KOREA LTD.
전화번호 : [phone]
FAX 번호 : [phone]
주소 : 서울시 마포구 상수동 351-16번지 로이코빌딩 3층
홈페이지 : http://www.totokr.co.kr
If the contents in the above column are not complete, the product warranty card shall be
deemed as invalid. Therefore, user should confirm the contents put in at the time of buying.
The items covered in this product warranty card are only limited to repair to those free repair
items as agreed in the product warranty card.
During the warranty period, if any failure occurs to the product (water leakage, seepage), the
user is requested to show the product warranty card and buying invoice to the sales shop or
installation shop for making a repair requirement.
＊
＊
＊
User
Sales shop or installation shop
Date of buying
Warranty period
The warranty is effective for a period of one（１）year from
the date of purchase.
Free Repair Regulations
During the warranty period, if the user uses the products of the company correctly according to
relevant instructions, adhesive labels, the company will provide free repair to any faulty product.
When any free repair is required due to damage within the warranty period, please bear
this
warranty and the buying invoice to entrust the installation shop or sales shop to handle
it.
Within the warranty period, the repair in the following occasions is paid repair.
① Any failure and damage due to any improper use or any improper repair and modification
conducted privately.
② Any failure and damage resulting from any carelessness or fault in installation construction.
③ Any failure and damage attributed to such reasons as removal for relocation after installation,
etc.
④ Any failure and damage due to using this product in occasions beyond the specified scope of
use (for example, home commodity is used for any business purpose).
⑤ Any damage caused by sand grains or dirt, etc.
⑥ Such adverse results as dirtiness, plating part rusting, etc. attributed to improper daily
maintenance and care.
⑦ Any failure and damage due to fire, earthquake, flood, lightning strike and other natural
disasters, public nuisances, gas damage (liquefied gas), salt damage and abnormal voltage, use
of any power supply (voltage, frequency) other than the specified ones, etc.
⑧ The occasions not specified in this warranty.
⑨ The occasion in which the user name, sales shop, installation shop or buying date is not filled
in.
⑩ No buying invoice can be presented.
This warranty applies to countries except China.
This product warranty card shall not be reissued when being lost. Customers are requested to
keep it properly.
1.
2.
3.
4.
5.
Product Warranty Card