Toto EGO II TX447SELN User manual

"EGO II" LEVER HANDLE 4 HOLES BATH & SHOWER SET TX447SELN
SPECIFICATIONS
OPERATING CONDITIONS
S06312N
TROUBLESHOOTING
INSTALLATION
1.
3.
5.
Lock Nut
2.
Shower Holder
Ø35
4.
6.
Flexible
Hose
Packing
Spout
Joint
Nut
Ø40
Hose Spring
Packing
Packing Hand Shower
Ø35
Ø35
Packing
Lock Nut
Body
Ceramic
Head Work
Handle *
Lock Nut
C
L
I
CK
R16
Lock Nut
Holder
Packing
Packing
1. AERATOR
2. CERAMIC
HEAD WORK
Hose
Stopper
Base
Flow Regulator Inside
(Don t remove)
Rain Spray
Button
Massage
Spray Button
CHECK
POINT
Unsatisfactory spray 1 Clean
Flow rate unsatisfactory 2 Remove and clean
Water leaks around the handle 3 Tighten
PROBLEM
SOLUTION
1. NOZZLES
Wavy Washer
MAINTENANCE
ATTENTION
All Finishes: Clean the finish with mild soapand warm water. Wipe
entire surface completely dry with clean soft cloth. Many cleaners may
contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which
couldadversely affect the finish and are not recommended forcleaning
Don t use abrasive cleaners orsolvents on faucets and fittings.
FlowRegulator should not be remove because it could
damage the system
As the product model is constantly updated, the actual product
maynot look the same as it shown in the diagram, but the
basic installation principles are thesame.
1.
2.
3.
Ø35 Hole
Hot
Water
Supply
Col d
Water
Supply
1. Watersupplypressure : 0.05 ~ 0.75 MPa.
2. Ensure that watersupply is clean ( NoSand, Dirt, Etc. )
G½
HC
240
175.5
max.30 331.5
Ø54
Ø54
Ø54
120120 120
* The red handle for left position and
the blue handle forright position.
**Tighten thehandle base by hand
Handle
Base**

"EGO II" LEVER HANDLE 4 HOLES BATH & SHOWER SET TX447SELN
G½
HC
240
175.5
max.30 331.5
Ø54
Ø54
Ø54
120120 120
SPESIFIKASI
S06312N
PEMASANGAN
1.
3.
5.
Lock Nut
Shower Holder
Ø35
4.
6.
Flexible
Hose
Packing
Spout
Joint
Nut
Ø40
Hose Spring
Packing
Packing Hand Shower
Ø35
Ø35
C
L
I
CK
R16
Lock Nut
Holder
Packing
Packing
1. AERATOR
2. CERAMIC
HEAD WORK
Hose
Stopper
Base
Rain Spray
Button
Massage
Spray Button
1. NOZZLES
Wavy Washer
Ø35 Hole
Hot
Water
Supply
Col d
Water
Supply
KONDISI OPERASIONAL
PEMELIHARAAN
PERHATIAN
Seluruh lapisan: Bersihkan lapisan akhir dengan sabun lembut dan air
hangat. Lap seluruh permukaan hingga benar-benarkering dengan kain
lembut yang bersih. Kebanyakan bahan pembersih mungkin mengandung
bahan kimia,seperti amonia, klorin, pembersih toilet, dll. yang dapat
mempengaruhi hasil akhir dan tidak disarankanuntuk dibersihkan
PENYELESAIAN MASALAH
Pancaran tidak memuaskan 1 Bersihkan
Laju aliran tidak memuaskan 2 Lepas dan bersihkan
Air bocor disekitar handle 3 Kencangkan
MASALAH
SOLUSI
POIN
PERIKSA
Jangan gunakan pembersih atau pelarut abrasif pada faucet dan fitting.
FlowRegulator tidak boleh dilepas karena dapat merusak sistem
Karena model produkterus mengalami pembaharuan, aktual produk
mungkin tidak sama dengan gambar,tapi prinsip dasar pemasangan
adalah sama.
1.
2.
3.
1. Tekanan sumber air: 0.05 ~ 0.7.5 MPa.
2. Pastikan kondisi sumber air adalah bersih (tidak ada pasir,
kotoran dan lain lain)
2.
Packing
Lock Nut
Body
Ceramic
Head Work
Handle *
Lock Nut
* Handle merah untuk posisi kiri
dan handle biru untuk posisi kanan
**Kencangkan handle base
dengan tangan
Handle
Base**
Flow Regulator Di dalam
(Jangan dilepas)