Town & Country Fireplaces TC36.NGST03 User manual

210705-12 TC36.NGST03 5056.42801.3
TC36 See-Thru
BLACK DIAMOND
BURNER KIT
IMPORTANT:
THESE INSTRUCTIONS ARETO REMAIN
WITH THE APPLIANCE INSTRUCTIONS
These instructions are supplementary to the Installation and
Operating Instructions supplied with the fireplace and should
be kept together. Refer to the Installation and Operating
Instructions for proper gas supply, safety requirements and
operating instructions.
PART#
TC36.NGST03
FOR TC36
SEE-THRU

2210705-12 TC36.NGST03 5056.42801.3
Package Contents
BURNER TUBE PART# TC36.50118398
SHUTTER CONTROL ROD PART# 5002.9692
BURNER TRAY ASSEMBLY PART# TC36.9690
2 BURNER SHIELD, FRONT/REAR PART# TC36.9693 PBK
LEFT BURNER SHIELD PART# TC36.9693.2 PBK
RIGHT BURNER SHIELD PART# TC36.9693.5 PBK
AIR CHANNEL INSERT PART# TC36.9697 PBK
INLET COVER PART# TC36.9699 PBK
PILOT SHIELD PART# TC36.9626.PBK
MANIFOLD ASSEMBLY PART# TC36.9692
2 MEDIA SPACER, FRONT/REAR PART# 9695
MEDIA SPACER, CENTER PART# 9694
TUMBLED GLASS MEDIA PART# 5012.01
HARDWARE PACKAGE PART# TC36.STHK03
Fig. #1

3
210705-12 TC36.NGST03 5056.42801.3
Black Diamond Burner Installation
1. Attach the manifold assembly to the
floor of the firebox using two screws.
(Fig. #2)
2. Connect the flex gas line to the
manifold ensuring a gas-tight
connection (Fig. #3).
3. If porcelain panels are not installed, install the left panel (Fig. #4) securing with panel retainer clip located on the
upper heat shield, and position the air channel insert into the air channel. (Fig. #5)
NOTE:The right side of the unit is the side with the control box inlet.
Fig. #2
Fig. #3
Fig. #4
Fig. #5

4210705-12 TC36.NGST03 5056.42801.3
4. Attach the inlet cover using the top
two screws of the control inlet
(Fig. #6) and install the right porcelain
panel.
5. Position the right burner shield over
the inlet cover ensuring that the pilot
assembly is protruding though the
half-hole between the inlet cover and
the right burner shield (Fig. #7).
6. While supporting the right burner
shield,install the rear burner shield
resting the edge of the right burner
shield onto the support tab of the rear
burner shield (Fig. #8).
Fig. #6
Fig. #7
Fig. #8

5
210705-12 TC36.NGST03 5056.42801.3
7. Install the front burner shield
positioning the support tab under the
right burner shield.
8. Install the left burner shield.This will
be a snug fit requiring some
alignment (Fig. #10).
9. Position the burner tray assembly on
top of the assembled shields and
attach it using four screws (Fig. #11).
NOTE: Ensure that the square
access hole of the tray is
positioned to the right (control
inlet side). (Fig. #11)
Fig. #11
Fig. #10
Fig. #9

6210705-12 TC36.NGST03 5056.42801.3
10. If the fireplace is equipped with a
millivolt pilot, attach it to the burner
tray before attaching pilot bracket.
If the fireplace is equipped with an
electronic pilot attach it to the pilot
bracket (Fig. #12) and then attach
the bracket to the burner tray
(Fig. #13).
11. Position a front/rear media spacer
at the rear of the burner tray
(Fig. #14).
12. Position the other at the front of the
tray (Fig. #15).
13. Loosen the screw on the burner tube
shutter enough to allow smooth
movement from open to closed
positions (visible in Fig. #17).
Fig. #12
Fig. #13
Fig. #14
Fig. #15

7
210705-12 TC36.NGST03 5056.42801.3
14. Install the burner tube by tipping the
inlet into the slot in the bottom of the
burner tray (Fig. #16).
15. Hold the burner tube in a position so
that the shutter control rod can be
inserted into the shutter tab (Fig.
#17) after passing through the rod
hole in the top right corner of the
front burner shield.
16. Set the burner tube into place
ensuring that it slips over the orifice
on the manifold assembly.
17. Attach the burner tube to the tray
with two screws (Fig. #18).
NOTE: Shutter must be fully open
for propane or fully closed for
natural gas (push down on the
shutter control rod to open, pull
up to close). Some adjustment
may be required (see page 9).
Fig. #16
Fig. #17
Fig. #18

8210705-12 TC36.NGST03 5056.42801.3
18. Position the center media spacer on
the inside of the burner tube
(Fig. #19).
19. Apply just enough tumbled glass
to lightly cover the burner tube
(Fig. #20).
20. Spread glass evenly over top of tube
and media spacers (Fig. #21).
NOTE:Too much tumbled glass
over the burner will cause sooting.
Fig. #19
Fig. #20
Fig. #21

9
210705-12 TC36.NGST03 5056.42801.3
Burner Flame Adjustment
The air shutter on the burner inlet
tube controls the primary combustion
air to the gas burner. It is set closed
at the factory for natural gas fuel.
Some adjustment may be necessary
to obtain desired flame and to
eliminate carbon deposits. Evaluate
flame appearance after the fireplace
has reached operating temperature.
See Fig. # 22 for proper flame
pattern.
Open primary air if the window glass
and firebox have carbon
accumulation and/or the flames are
long, dark and stringy.The shutter
may also be opened to lessen the
flame height.
CAUTION:
Burner area may be hot!
Turn off the fireplace and allow the
unit to cool before proceeding.
To Adjust: (See Fig. # 23)
Push the shutter control rod to
increase the amount of primary air to
create a more blue flame.
Pull the shutter to decrease the
amount of primary air to create a
more yellow flame.
NOTE:
Proper air shutter setting is
required.
The flame should be just orange
and "lazy". It should NEVER be
set to create sooting on internal
parts and window glass.
Fig. #22
Fig. #23
Shutter Control

10 210705-12 TC36.NGST03 5056.42801.3
Replacement Parts
ITEM PART NUMBER DESCRIPTION
19697 AIR CHANNEL INSERT
29695 MEDIA SPACER, FRONT/REAR
3TC36.50118398 BURNER TUBE
49694 MEDIA SPACER, CENTER
59690.5 TRAY TRIM
69626.002 PILOT SHIELD
79699 INLET COVER
89693.5 BURNER SHIELD, RIGHT
99691 TRAY SUPPORT
10 9693 BURNER SHIELD FRONT/REAR
11 5002.9692 SHUTTER CONTROL ROD
12 9693.2 BURNER SHIELD, LEFT
13 9690 BURNER TRAY
TC36.STHK03 HARDWARE PACKAGE
TC36.9692 MANIFOLD ASSEMBLY
14 9692 MANIFOLD BRACKET
15 5019.21 FITTING, ORIFICE IN
16 5021.01 FITTING, LOCKNUT
17 5022.12 ORIFICE, NG
5021.31 ORIFICE, LP
NOTE:
FIREPLACE & VALVE REPLACEMENT
PARTS ARE LOCATED IN THE
APPLIANCE INSTRUCTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14 15
16
17

11
210705-12 TC36.NGST03 5056.42801.3
Notes

Printed in Canada 5056.42801.3
TOWN & COUNTRY FIREPLACES
www.townandcountryfireplaces.net
Toll Free: 1-888-223-0088
2975 Allenby Road, Duncan, BC Canada V9L 6V8