TP-Link VIGI NVR1004H-4P User manual

Product Overview
Hard Drive Installation
Quick Installation Guide
PoE Network Video Recorder
Package Contents
Network Video Recorder
Quick Installation Guide
Mouse
Power Adapter HDD Screws
1
3
2
2. Attach the 4 included HDD screws to your hard drive. Do not fasten.
1. Remove the xing screws on the side and back panels to open the
cover of the NVR.
Front Panel
Back Panel
When installing for the rst time, please prepare a 3.5-inch hard disk drive (HDD). It is recommended to use the HDD of surveillance or enter-
prise level. Before installation, please disconnect the power from the network video recorder (NVR).
POWER
PoE PortUSB Port
VGA
HDMI
LAN Port
AUDIO OUT
AUDIO IN
3. Match the 4 screws on the HDD with the 4 holes on the NVR, and insert
the HDD interface into the slot.
4. Flip the NVR upside down and fasten the HDD screws. Replace the
cover and fasten the screws of the NVR.
Hard Disk Drive (HDD)
USB
Interface Description
2 USB ports for additional devices such as USB mouse, USB storage device,
and USB keyboard.
Output port for analog video signals.
Connect your monitor to this port if it uses VGA connection.
Designed to connect to the device with a bandwidth of 100/10 Mbps. The port
can also provide power for PoE PDs (recommended for PoE cameras).
PoE
RJ45 10/100Mbps self-adaptive Ethernet port.
Connect to an Ethernet device (eg. router and switch).
AUDIO IN /
AUDIO OUT
VGA
HDMI
POWER Connector for power input.
LAN
Output port for high-denition audio and video signals. Connect
your monitor to this port if it uses HDMI connection.
Connector for audio input and output.
Note: Audio input only supports microphones with power supply.
LED USB Port
*Images may dier from actual products. VIGI NVR1008H-8MP is used for demonstration in this guide
©2022 TP-Link 7106509913 REV1.0.1
On: A device is linked to the port but no activity.
Flashing: Transmitting or receiving data.
O: No device is linked to the corresponding port.
Link / Act
On: The port is supplying power normally.
Flashing: Overload or short circuit is detected.
O: Not providing PoE power on the port.
PoE
On: The total PoE power reaches the warning threshold.
Flashing: The total PoE power has reached the warning threshold for more than 2 minutes.
O: The total PoE power does not reach the warning threshold.
PoE Max
On: The HDD is normal.
O: No HDD or the HDD is malfunctioning.
HDD
On: Network is working properly.
Flashing: Data is being transmitted or received.
O: Network is malfunctioning.
LAN
On: System is running normally.
O: System is running abnormally.
SYS
LED Indication
Kensington
Security Slot
Grounding Terminal
Kensington Security Slot: Secure the lock (not provided) into the security slot to prevent the device
from being stolen.
Grounding Terminal: The device comes with lightning protection mechanism.
Rubber Feet (for some models)

Step 1. Connect your cameras to the PoE ports of the NVR or the same
network as your NVR.
Step 2. Follow the instructions to nish Quick Setup.
1. Create a login password for the NVR and a preset password for your unset cameras.
Note: Enter an email address for resetting the password of NVR or cameras.
2. Click Auto Initialize and the NVR will automatically nd and add the cameras in
your network.
Note: If you don’t want to use Auto Initialize, click Manually Initialize and follow the
Setup Wizard to add cameras in your network and complete the setup.
Step 3. Right click on the Live View screen to open the Main Menu for
management.
(Optional) Step 4. Bind your NVR to a TP-Link ID for remote access and
management.
1. Right click on the Live View screen and click Settings.
2. Click Cloud Services on the top, enter your TP-Link ID and password, and click
Bind.
Hardware Connection
Follow the steps below to complete the hardware connection.
1. Connect your monitor to the HDMI or VGA port according to the connection
port it supports.
2. Connect your monitor to a power source and turn it on.
3. Connect the LAN port of the NVR to a network device with an Ethernet cable.
4. Connect the provided USB Mouse to the USB Interface of the NVR.
5. Connect the power adapter to the NVR.
NVR can add and manage cameras in batches.
* Here we use TP-Link cameras as an example. For other camera brands, please refer to their User Manuals to add the cameras.
Conguration
5
4
For technical support, the user guide and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
To ask questions, find answers, and communicate with TP-Link users or engineers,
please visit https://community.tp-link.com to join TP-Link Community.
Frequently Asked Questions
Q1. What should I do if I forget the login password of my NVR?
A1. Click Forgot Password on the login page and then follow the instructions to reset the password.
A2. Remove the cover, then press and hold the Reset button inside the NVR for over 3 seconds. The NVR will restore
to the factory settings. Then follow Quick Setup to create a login password.
Q2. What can I do if no cameras are found?
A1. Refresh to discover your cameras again.
A2. Make sure the cameras are powered on.
A3. Make sure your cameras and NVR or computer are in the same network.
A4. Try to add your cameras manually.
Q3. What can I do if my NVR fails to connect to the Internet?
A1. Check if the internet is working properly.
A2. Make sure your NVR is in the same network segment as your network devices,or select Auto as the mode to
congure the NVR to obtain a dynamic IP address. For more details, please refer to the NVR’s User Guide.
If you have more questions, please visit https://www.tp-link.com/support/faq/2850/.
Safety Information
This device is restricted to indoor use only.
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions,
please don't hesitate to contact us.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Place the device with its bottom surface downward. Install it at stable places, and prevent it from falling.
The power adapter must be used indoors. Make sure that the temperature of the power adapter is within 0-40°C.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
*Some devices may be incompatible, such as wireless mouse.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will
occur due to improper use of the device. Please use this product with care and operate at your own risk.
Monitor
Network Device
(e.g. Router, Switch)
More Management Methods
1. Download the VIGI Security Manager on your computer at
https://www.tp-link.com/support/download/vigi-security-
manager/.
2. Install the VIGI Security Manager and open it.
3. NVR on the same network as your computer can be
automatically discovered. Go to Settings > Discovered
Devices, click Add, and follow the instructions to add your
NVR.
Method 1: Via the VIGI Security Manager
(Windows only)
You can add and manage your devices via any of the methods below.
View live video and modify NVR settings on your
computer.
Method 3: Via a Web Browser
View live video and modify NVR settings via a web
browser.
Method 2: Via the TP-Link VIGI App
Remotely view live video, manage NVR, and get instant
alerts.
1. Download and install the TP-Link VIGI app.
2. Open the app and log in with your TP-Link ID. If you don’t
have an account, sign up rst.
3. Tap the + button on the top right and follow the app
instructions to add your NVR.
or
or
Mouse
Cautions
If you want to turn o the NVR after installing the hard drive, right click on the Live View
screen and click the Power button on Main Menu of your monitor. Do not unplug it directly.
The input voltage should match the power requirements of the NVR.
The buzzer on the NVR may be triggered when no hard drive is installed or the hard drive in
the NVR hasn’t been initialized. You can turn it o in Event-Exception Detection-Disk
Exception.
The terms HDMI, HDMI High-Denition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Note:
Make sure your NVR can get access to the internet before binding.
If you don’t have a TP-Link ID, sign up rst.
If your NVR fails to connect to the Internet, please refer to FAQ-Q3.
For more instructions, please refer to the NVR’s User Guide.
If you want to add a camera after Quick Setup, please follow the steps below:
1. Right click on the Live View screen and click Add Camera.
2. Select a camera and click + to add your camera directly. If you have disabled Plug
and Play on your NVR, please create a password or use the preset password for
your unset camera.
Note:
The password preset for cameras in Quick Setup will be applied to your unset cameras.
If your cameras have been activated, use the previous passwords to add and manage the
cameras.
If you can’t nd your camera, refer to FAQ-Q2.
PoE IPCs
USB Storage Device
or Keyboard
1. Find the NVR's IP address on your router’s client page.
2. On your local computer, open a web browser and enter
https://NVR’s IP address (https://192.168.0.240 by default).
3. Select your Country/Region and Time Zone.
4. Set a password to activate the NVR.
Done. You can manage and change NVR settings, and add
cameras on the web management page.
Reset Button
RESET
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of
ammable liquid or gas;
Do not leave a battery subjected to extremely low air pressure that may result in an explosion or the leakage of ammable liquid or gas.
This equipment is not suitable for use in locations where children are likely to be present.