TP-Link TW-MR3220 User manual

TW-MR3220
3G/4G Wireless N Router
Rev: 2.1.1
19100
11711

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD . Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1）This device may not cause harmful interference.
2）This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating

in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the
following two conditions:
1）This device may not cause interference, and
2）This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1）l’appareil ne doit pas produire de brouillage;
2）l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le
brouillage est susceptible d’en compromettre le fonctionnement.
This radio transmitter (IC: 8853A-TL-MR3220/ Model: TL-MR3220) has been approved by
Industry Canada to operate with the antenna types listed below with the maximum permissible
gain indicated. Antenna types not included in this list (Appendix C), having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 8853A-XXX/ Model: XXX) a été approuvé par Industrie Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal. Les types d'antenne non inclus dans cette liste (Annexe A), et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20

cm de distance entre la source de rayonnement et votre corps.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
NCC Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電
信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність
вимогам нормативних документів та вимогам, що передбачені чинними
законодавчими актами України.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
Safety Information

When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect
the product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
Adapter shall be installed near the equipment and shall be easily accessible. The plug
considered as disconnect device of adapter.
Use only power supplies which are provided by manufacturer and in the original
packing of this product.
Alert to service person
CAUTION
DOUBLE POLE / NEUTRAL FUSING
For EU/EFTA, this product can be used in the following countries:
Explanation of the symbols on the product label
Symbol Explanation
Class II equipment
AC voltage
DC voltage
Polarity of output terminals
Indoor use only
AT BE BG CH CY CZ DE DK
EE ES FI FR GB GR HR HU
IE IS IT LI LT LU LV MT
NL NO PL PT RO SE SI SK

Hazard live parts
Energy efficiency Marking
Protection earth
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic
equipment (WEEE). This means that this product must be handled pursuant to
European directive 2012/19/EU in order to be recycled or dismantled to minimize
its impact on the environment.
User has the choice to give his product to a competent recycling organization or to
the retailer when he buys a new electrical or electronic equipment.
To prevent possible hearing damage, d
o not listen at high volume levels for long
periods.

TP-LINK TECHNOLOGIES CO., LTD
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 3G/4G Wireless N Router
Model No.:TL-MR3220
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.8.1:2008 & EN 301 489-17 V2.2.1
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN60950-1:2006+A11
：
2009+A1:2010+A12:2011
EN62311:2008
The product carries the CE Mark:
Person responsible for making this declaration:
Huang Jing
Regulatory Compliance Manager
Date of issue: 2015

CONTENTS
Chapter 1. Introduction ......................................................................................... 1
1.1 Overview of the Router...................................................................................................1
1.2 Conventions ....................................................................................................................1
1.3 Main Features................................................................................................................. 1
1.4 Panel Layout ................................................................................................................... 2
1.4.1 The Front Panel ..................................................................................................2
1.4.2 The Rear Panel...................................................................................................3
1.4.3 The Side Panel ...................................................................................................3
Chapter 2. Connecting the Router ....................................................................... 4
2.1 System Requirements ....................................................................................................4
2.2 Installation Environment Requirements.......................................................................... 4
2.3 Connecting the Router....................................................................................................4
Chapter 3. Quick Installation Guide ..................................................................... 6
3.1 TCP/IP Configuration...................................................................................................... 6
3.2 Quick Installation Guide..................................................................................................6
Chapter 4. Configuring the Router ..................................................................... 11
4.1 Login ............................................................................................................................. 11
4.2 Status ............................................................................................................................ 11
4.3 Quick Setup ..................................................................................................................12
4.4 WPS .............................................................................................................................. 12
4.5 Network.........................................................................................................................19
4.5.1 Internet Access ................................................................................................. 19
4.5.2 3G/4G................................................................................................................ 20
4.5.3 WAN .................................................................................................................. 23
4.5.4 MAC Clone........................................................................................................32
4.5.5 LAN ................................................................................................................... 33
4.6 Wireless ........................................................................................................................33
4.6.1 Wireless Settings ..............................................................................................34
4.6.2 Wireless Security ..............................................................................................36
4.6.3 Wireless MAC Filtering .....................................................................................38
4.6.4 Wireless Advanced ........................................................................................... 40
4.6.5 Wireless Statistics ............................................................................................. 41
4.7 DHCP ............................................................................................................................ 42
4.7.1 DHCP Settings.................................................................................................. 42
4.7.2 DHCP Clients List ............................................................................................. 43
4.7.3 Address Reservation.........................................................................................43
4.8 Forwarding ....................................................................................................................45
4.8.1 Virtual Servers...................................................................................................45

4.8.2 Port Triggering .................................................................................................. 46
4.8.3 DMZ .................................................................................................................. 48
4.8.4 UPnP.................................................................................................................49
4.9 Security .........................................................................................................................50
4.9.1 Basic Security ...................................................................................................50
4.9.2 Advanced Security............................................................................................ 51
4.9.3 Local Management ...........................................................................................53
4.9.4 Remote Management .......................................................................................54
4.10 Parental Control............................................................................................................54
4.11 Access Control.............................................................................................................. 57
4.11.1 Rule...................................................................................................................57
4.11.2 Host...................................................................................................................59
4.11.3 Target ................................................................................................................60
4.11.4 Schedule ...........................................................................................................62
4.12 Advanced Routing ........................................................................................................64
4.12.1 Static Routing List .............................................................................................64
4.12.2 System Routing Table....................................................................................... 65
4.13 Bandwidth Control.........................................................................................................66
4.13.1 Control Settings ................................................................................................66
4.13.2 Rules List ..........................................................................................................66
4.14 IP & MAC Binding .........................................................................................................67
4.14.1 Binding Settings ................................................................................................67
4.14.2 ARP List ............................................................................................................ 69
4.15 Dynamic DNS ...............................................................................................................69
4.15.1 Comexe.cn DDNS.............................................................................................70
4.15.2 Dyndns.org DDNS ............................................................................................ 70
4.15.3 No-ip.com DDNS .............................................................................................. 71
4.16 System Tools................................................................................................................. 72
4.16.1 Time Settings ....................................................................................................72
4.16.2 Diagnostic .........................................................................................................73
4.16.3 Firmware Upgrade ............................................................................................ 75
4.16.4 Factory Defaults................................................................................................76
4.16.5 Backup & Restore ............................................................................................. 76
4.16.6 Reboot...............................................................................................................76
4.16.7 Password ..........................................................................................................77
4.16.8 System Log ....................................................................................................... 77
4.16.9 Statistics ............................................................................................................ 79
Appendix A: FAQ....................................................................................................... 81
Appendix B: Configuring the PCs ........................................................................... 86

Appendix C: Specifications...................................................................................... 90
Appendix D: Glossary .............................................................................................. 91
Appendix E: Compatible 3G/4G USB Modem ......................................................... 93

TL-MR3220
3G/4G Wireless N Router User Guide
-1-
Chapter 1. Introduction
1.1 Overview of the Router
TP-LINK understands the need for sharing the 3G/4G connection locally that benefits our end
users. We realize the convenience with our latest wireless N 3G/4G Routers ----- they give you
the freedom to quickly set up a stable and high speed wireless network, up to 150Mbps,
on-the-go and share a 3G/4G connection. By connecting a LTE/HSPA/UMTS/EVDO USB Card
to the Router, a Wi-Fi hotspot is instantly established allowing users to share a Internet
connection anywhere 3G/4G coverage is available. So whether you’re on the train, camping, or
at a construction site, you’ll have a reliable wireless connection to accommodate your
networking needs.
The router provides 3G/4G and WAN (xDSL, static IP, or dynamic IP) two kinds of broadband
connections to get on the Internet, you can via the Internet no matter at home or outside on
business. Automatic 3G/4G and WAN failover feature just provide nonstop internet connection.
TP-LINK 3G/4G Router provides up to 150Mbps, faster than that of traditional 11g products,
surpasses 11G performance enabling the use of high bandwidth-consuming applications such
as HD Videos.
With just pressing on the 'WPS' button, the Router automatically establishes a WPA2 secure
connection for solid security in under a minute.
QoS acts as a “bandwidth manager” to ensure that those programs that are sensitive to lag are
given as much bandwidth as possible to avoid lag. This feature makes an impression
immensely when users are streaming video or music and especially when playing online games
where lag often means “Game Over”.
1.2 Conventions
The router mentioned in this guide stands for TL-MR3220 3G/4G Wireless N Router without any
explanation.
1.3 Main Features
One 10/100M Auto-Negotiation RJ45 WAN port, four 10/100M Auto-Negotiation RJ45 LAN
ports, supporting Auto MDI/MDIX
Compatible with LTE/HSPA/UMTS/EVDO USB dongle
Automatic 3G/4G / WAN failover
Wireless N speed up to 150Mbps
Quality of Service-Qos
Wi-fi Protected Setup
Incredibly High Speed
3G/4G and WAN Broadband

TL-MR3220
3G/4G Wireless N Router User Guide
-2-
1T2R MIMO, CCA technologies deliver greater coverage and higher speed
Wireless security encryption easily at a push of “WPS” button
WDS wireless bridge provides seamless bridging to expand your wireless network
Backward compatible with 802.11b and 802.11g devices
Provides WPA/WPA2-Enterprise, WPA/WPA2-Personal authentication, TKIP/AES
encryption security
Supports 3G/4G/Dynamic IP/Static IP/PPPoE/L2TP/PPTP Internet access
Supports Virtual Server, Special Application and DMZ host
Supports UPnP, Dynamic DNS, Static Routing
Provides Automatic-connection and Scheduled Connection on certain time to the Internet
Built-in NAT and DHCP server supporting static IP address distributing
Connects Internet on demand and disconnects from the Internet when idle for PPPoE
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List)
Supports Flow Statistics
Supports firmware upgrade and Web management
1.4 Panel Layout
1.4.1 The Front Panel
The Router’s LEDs are located on the front panel (View from left to right).
Item Status Indication
(PWR)
On
Power is on.
Off
Power is off.
(SYS)
On
The Router is initializing.
Flashing
The Router is working properly.
Off
The Router has a system error.
(WLAN)
Flashing
The Wireless function is enabled.
Off
The Wireless function is disabled.
（WAN）
（LAN1-4
）
On
A device is linked to the corresponding port but there is no
activity.
Flashing
An active device is linked to the corresponding port.
Off
No device is linked to the corresponding port.
（USB）
On
The USB 3G/4G modem is connected but no data being
transferred.
Flashing
Data is received or sent through the 3G/4G modem.
Off
The USB 3G/4G modem is not connected.
（WPS）
Slow
Flash
A wireless device is connecting to the network by WPS
function. This process will last in the first 2 minutes.
On
A wireless device has been successfully added to the network
by WPS function.

TL-MR3220
3G/4G Wireless N Router User Guide
-3-
Quick
Flash
A wireless device failed to be added to the network by WPS
function.

Note:
After a device is successfully added to the network by WPS function, the WPS LED will keep on
for about 5 minutes and then turn off.
1.4.2 The Rear Panel
The following parts are located on the rear panel (View from left to right).
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this router.
ON/OFF: The switch is for you to turn on/off the Router, but only with the Router powered
on.
4,3,2,1 (LAN): These ports (4,3,2,1) connect the Router to the local PC(s)
WAN:This WAN port is where you will connect the DSL/cable Modem, or Ethernet
WPS/RESET:
There are two ways to reset to the Router's factory defaults:
1) Use the Factory Defaults function on “System Tools -> Factory Defaults” page in
the Router's Web-based Utility.
2) Use the Factory Default Reset button: With the Router powered on, use a pin to press
and hold the WPS/RESET button (about 5 seconds) until the SYS LED becomes
quick-flash from slow-flash. And then release the button and wait the Router to reboot
to its factory default settings.
Wireless antenna: To receive and transmit the wireless data.
1.4.3 The Side Panel
The following parts are located on the side plate (View from left to right).
WIFI: This switch is an easy and convenient operation for you to turn on or off the wireless
network.
USB: Connect to the USB Modem.

TL-MR3220
3G/4G Wireless N Router User Guide
-4-
Chapter 2. Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router
is connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer 5.0 , Netscape Navigator 6.0 or above
2.2 Installation Environment Requirements
Place the Router in a well ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0 ℃~40℃ (32℉ ~104℉ )
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that,
please install the Router according to the following steps. Don't forget to pull out the power plug
and keep your hands dry.
1. Power off your Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your
wireless network. The place must accord with the Installation Environment Requirements.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the PC(s) or Switch/Hub in your LAN to the LAN Ports of the 3G/4G Router with
Ethernet cable.
5. The 3G/4G Router supports both 3G/4G and WAN connection; so you can insert 3G/4G
USB Modem to the USB port of the Router (as shown in Figure 2-1), or connect the
DSL/Cable Modem to the WAN port of the Router (as shown in Figure 2-2). Please visit our
website http://www.tp-link.com to get the latest USB modems compatibility, and we
recommend you to check whether the modem in your hand has already been tested by us.
6. Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. The Router will start to work automatically.
7. Power on your Cable/DSL Modem.

TL-MR3220
3G/4G Wireless N Router User Guide
-5-

TL-MR3220
3G/4G Wireless N Router User Guide
-6-
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your 3G/4G Wireless N
Router using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default IP address of the 3G/4G Wireless N Router is 192.168.0.1. And the default Subnet
Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all
the default values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address
for your PC in the following two ways.
Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: "Configuring the PC."
2) Configure the network parameters. The IP address is 192.168.0.xxx ("xxx" is any number
from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.0.1 (The Router's
default IP address)
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If
you need instructions as to how to do this, please refer to Appendix B: "Configuring the
PC."
2) Then the built-in DHCP server will assign IP address for the PC.
3.2 Quick Installation Guide
With a Web-based (Internet Explorer or Netscape®Navigator) utility, it is easy to configure and
manage the 3G/4G Wireless N Router. The Web-based utility can be used on any Windows,
Macintosh or UNIX OS with a Web browser.
1. To access the configuration utility, open a web-browser and type in the default address
http://192.168.0.1 in the address field of the browser.
After a moment, a login window will appear, similar to the figure below Enter admin for the User
Name and Password, both in lower case letters. Then click the OK button or press the Enter
key.

TL-MR3220
3G/4G Wireless N Router User Guide
-7-

Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.
2. After successful login, you can click the Quick Setup to quickly configure your Router.
Click Next to proceed to the next screen.
3. Select a desired Internet Access mode and then click Next. The configuration for each
mode is similar. As follows we will take 3G/4G Only mode for example.

TL-MR3220
3G/4G Wireless N Router User Guide
-8-
3G/4G Preferred
In this mode, the Router will try 3G/4G access first. If 3G/4G access fails and WAN
access is valid, or if no 3G/4G USB modem is inserted, the Router would switch to WAN
access. Once the Router succeeds to connect to the 3G/4G network, the Router would
stop the WAN connection and switch back to 3G/4G access immediately.
3G/4G Only
In this mode, the Router will try 3G/4G access only. WAN access is disabled.
WAN Preferred
In this mode, the Router will try WAN access first. If the WAN access fails and 3G/4G
access is valid, the Router would switch to 3G/4G access. Once the Router succeeds to
connect to the WAN network, the Router would stop the 3G/4G connection and switch
back to WAN access immediately.
WAN Only
In this mode, the Router will try WAN access only. 3G/4G access is disabled.
4. The next screen will appear as shown below. You need to set the required parameters and
then click Next.
Location - Select the location where you're enjoying the 3G/4G card.
Mobile ISP - Select the ISP (Internet Service Provider) you apply to for 3G/4G service. The
Router will show the default Dial Number and APN of that ISP. If your ISP is not listed in the
Mobile ISP, check the box before Set the Dial Number, APN, Username and Password
manually and fill the Dial Number and APN blanks below.
Authentication Type - Some ISPs need a specific authentication type. Please confirm it
with your ISP or keep it Auto.
Dial Number & APN - Set these two parameters manually after Set the Dial Number, APN,
Username and Password manually is checked.
Username/Password - Enter the Username and Password provided by your ISP. These
fields are optional but case-sensitive.

TL-MR3220
3G/4G Wireless N Router User Guide
-9-
5. Configure the Wireless settings on the screen as shown below, then click Next.
Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list.
Wireless Network Name - Enter a value of up to 32 characters. The same name of
Wireless Network Name (SSID) must be assigned to all wireless devices in your network.
Considering your wireless network security, the default Wireless Network Name is set to
be TP-LINK_XXXXXX (XXXXXX indicates the last six unique numbers of each Router’s
MAC address). This value is case-sensitive. For example, TEST is NOT the same as test.
Region -Select your region from the pull-down list. This field specifies the region where
the wireless function of the Router can be used. It may be illegal to use the wireless
function of the Router in a region other than one of those specified in this field. If your
country or region is not listed, please contact your local government agency for
assistance.
Channel - This field determines which operating frequency will be used. The default
channel is set to Auto, so the AP will choose the best channel automatically. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point.
Mode - This field determines the wireless mode which the Router works on.
Channel Width -Select any channel width from the pull-down list. The default setting is
automatic, which can adjust the channel width for your clients automatically.
Wireless Security - You can select one of the following security options.
Disable Security - The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without encryption. It
is recommended strongly that you choose one of following options to enable security.
WPA-Personal/WPA2-Personal - Select WPA based on pre-shared passphrase.
Password - You can enter ASCII or Hexadecimal characters.