TP-Link TX-6610 User manual

TX-6610
1-Port Gigabit GPON Terminal
REV: 3.0.0
1910011424

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
BSMI Notice
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。

●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
Adapter shall be installed near the equipment and shall be easily accessible.
The plug considered as disconnect device of adapter.
Use only power supplies which are provided by manufacturer and in the original
packing of this product.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SG SK TR UA US

TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 1-Port Gigabit GPON Terminal
Model No.: TX-6610
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents：
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013
The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2015-09-25
TP-LINK TECHNOLOGIES CO., LTD
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China

CONTENTS
Chapter 1. Product Overview ...................................................................................1
1.1 Product Overview..........................................................................................................1
1.2 Main Features ...............................................................................................................1
1.3 Panel Layout .................................................................................................................2
1.3.1 The Front Panel ....................................................................................................................2
1.3.2 The Back Panel.....................................................................................................................3
Chapter 2. Connecting the Terminal .......................................................................4
2.1 System Requirements...................................................................................................4
2.2 Installation Environment Requirements .........................................................................4
2.3 Connecting the Terminal ...............................................................................................4
Chapter 3. Quick Installation Guide ........................................................................6
3.1 TCP/IP Configuration ....................................................................................................6
3.2 Quick Installation Guide ................................................................................................9
Chapter 4. Configuring the Terminal.....................................................................11
4.1 Login...........................................................................................................................11
4.2 Status..........................................................................................................................11
4.3 Network Setting...........................................................................................................13
4.3.1 PON Certification ............................................................................................................... 13
4.3.2 VLAN Setting ..................................................................................................................... 14
4.3.3 LAN Setting........................................................................................................................ 15
4.4 Management ...............................................................................................................16
4.4.1 User Management ............................................................................................................. 16
4.4.2 Firmware Upgrade ............................................................................................................. 17
4.4.3 Factory Defaults................................................................................................................. 18
4.4.4 Reboot ............................................................................................................................... 18
Appendix A: Specifications ...................................................................................19
Appendix B: Troubleshooting ...............................................................................20

TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 1. Product Overview
Thank you for choosing the TX-6610 1-Port Gigabit GPON Terminal.
1.1 Product Overview
TP-LINK’s TX-6610 is a next-generation Gigabit Passive Optical Network (GPON) terminal, ideal
for Fiber to the Home solution. It’s an incredibly robust device allowing users to access high-speed
internet connections via its GPON port and share it with a Gigabit Ethernet port. With the
transmission rates of up to 2.488Gbps, one GPON port and one Gigabit Ethernet port, the
TX-6610 provides high-performance forwarding capabilities to ensure smooth VoIP, HD video
streaming experiences.
In this guide, Terminal stands for the device TX-6610.
1.2 Main Features
Complies with ITU G.984.1, ITU G.984.2, ITU G.984.3 and ITU G.984.4 provides users
comprehensive GPON network compatibility
Downstream rates of up to 2.488Gbps and upstream rates up to 1.244Gbps
Gigabit port ensures rapid transfer speeds
Quality of Service control for traffic prioritization and bandwidth management
Quick and hassle-free installation
Intelligent power-saving method
Built-in DHCP server
1

TX-6610
1-Port Gigabit GPON Terminal User Guide
1.3 Panel Layout
1.3.1 The Front Panel
Figure 1-1
The GPON Terminal’s LEDs are located on the front panel. They indicate the device’s working
status. For details, please refer to LED Explanation.
LED Explanation:
Name Status Indication
Power
On Power is on.
Off Power is off.
GPON
On The Terminal is registered with the ISP.
Flashing The Terminal is trying to register with the ISP.
Off The Terminal is not yet registered with the ISP.
LOS
On The Terminal is unable to transmit optical signal.
Flashing
No optical signal is received or the received signal is too
weak.
Off The Terminal is receiving optical signal properly.
2

TX-6610
1-Port Gigabit GPON Terminal User Guide
LAN
On A device is connected to the LAN port.
Flashing The LAN port is transmitting or receiving data.
Off No device is connected to the LAN port.
1.3.2 The Back Panel
Figure 1-2
ON/OFF: The switch for the power.
POWER: The Power plug is where you will connect the power adapter.
RESET: There are two ways to reset the Terminal's factory defaults.
Method one: With the Terminal powered on, use a pin to press and hold the Reset button for
at least 5 seconds. And the Terminal will reboot to its factory default settings.
Method two: Restore the default setting from Management Factory Defaults of the
Terminal's Web-based utility.
GPON: The GPON is where you will connect the fiber.
LAN: Through the port, you can connect the Terminal to your PC or the other Ethernet
network devices.
3

TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 2. Connecting the Terminal
2.1 System Requirements
Broadband Internet Access Service (GPON).
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.
TCP/IP protocol on each PC.
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
2.2 Installation Environment Requirements
The Product should not be located where it will be exposed to moisture or excessive heat.
Place the Terminal in a location where it can be connected to the various devices as well as to
a power source.
Make sure the cables and power cord are safely placed out of the way so they do not create a
tripping hazard.
The Terminal can be placed on a shelf or desktop.
Keep away from the strong electromagnetic radiation and the device of electromagnetic
sensitive.
2.3 Connecting the Terminal
Before installing the device, please make sure your broadband service provided by your ISP is
available. If there is any problem, please contact your ISP. Before cable connection, cut off the
power supply and keep your hands dry. You can follow the steps below to install it.
Step 1: Connect the fiber. Plug one end of the fiber into the GPON port on the rear panel of
TX-6610, and insert the other end into the wall socket.
Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s
Ethernet port or a regular hub/switch port, and the other end to the LAN port on the
TX-6610.
Step 3: Power on the computers and LAN devices.
Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear
of the device and plug in the adapter to an electrical outlet or power extension. The
electrical outlet shall be installed near the device and shall be easily accessible.
Step 5: Press the ON/OFF button of your Terminal.
4

TX-6610
1-Port Gigabit GPON Terminal User Guide
Figure 2-1
5

TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 3. Quick Installation Guide
3.1 TCP/IP Configuration
After you directly connect your PC to the Terminal TX-6610 or connect your adapter to a
Hub/Switch which has connected to the Terminal, you need to configure your PC’s IP address. We
use the procedures in Windows 7 as an example, for other systems refer to T4 for instructions.
Step 1: Right-click Network icon(e.g. ) on the system tray, and select “Open Network and
Sharing Center > Change adapter settings”.
Step 2: Right click the icon that showed below, select Properties on the prompt page.
Figure 3-1
6

TX-6610
1-Port Gigabit GPON Terminal User Guide
Step 3: In the prompt page that showed below, double click on the Internet Protocol Version 4
(TCP/IPv4).
Figure 3-2
7

TX-6610
1-Port Gigabit GPON Terminal User Guide
Step 4: Select both Obtain an IP address automatically and Obtain DNS server address
automatically. Then click OK.
Figure 3-3
Step 5: Back to previous interface, click OK to save the settings.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select run tab, type cmd or command in the field
and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
Terminal has been established.
Figure 3-4
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the Terminal.
8

TX-6610
1-Port Gigabit GPON Terminal User Guide
Figure 3-5
You can check it following the steps below:
1) Is the connection between your PC and the Terminal correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should
be lit.
2) Is the TCP/IP configuration for your PC correct?
If the Terminal's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the TX-6610 1-Port Gigabit GPON
Terminal. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web
browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type the default address
http://192.168.1.1 in the address field of the browser.
Figure 3-6
After a moment, a login window will appear, similar to the Figure 3-7. Enter admin for the
Username and Password, both in lower case letters. Then click the Login button or press the
Enter key.
Figure 3-7

Note:
1) Do not mix up the username and password with your Terminal account username and
password which are needed for PPP connections.
9

TX-6610
1-Port Gigabit GPON Terminal User Guide
2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
Go to Toolsmenu→Internet Options→Connections→LAN Settings, in the screen that
appears, cancel the Using Proxy checkbox, and click OK to finish it.
2. After your successful login, you will see the Login screen as shown in Figure 3-8. Click
Network Setting PON Certification to complete the PON setting. You are required to
enter GPON Password or GPON SN or both provided by your ISP to pass the ISP
authentication. For details, please consult your ISP. Click Save to make your settings take
effect.
Figure 3-8
3. Establish your Internet connection according to the ISP's specific instructions, such as a
dial-up connection. For details, please refer to T1 in Troubleshooting.

Note:
If you need assistance, contact your ISP.
10

TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 4. Configuring the Terminal
This chapter will show each Web page's key function and the configuration way.
4.1 Login
After your successful login, you will see the main menus on the left of the Web-based utility. On
the right, there are the corresponding explanations and instructions.
The detailed explanations for each Web page’s key function are listed below.
4.2 Status
Choose “Status”, you can see the corresponding information about System Status, LAN, PON
and Statistics.
11

TX-6610
1-Port Gigabit GPON Terminal User Guide
Figure 4-1
12

TX-6610
1-Port Gigabit GPON Terminal User Guide
System Status:Here shows the system information of the Terminal.
LAN: The current port status of the Terminal.
PON: Here shows the Terminal’s current GPON module information.
Statistics:Here you can view the statistics of the Terminal.
Click Refresh to update this page.
4.3 Network Setting
Choose “Network Setting”, there are three submenus under the main menu. Click any one of
them, and you will be able to configure the corresponding function.
4.3.1 PON Certification
Choose “Network Setting”“PON Certification”, the GPON Configuration screen will appear on
the page as shown in Figure 4-2. You are required to enter the GPON Password or GPON SN or
both to pass the ISP authentication before you connect to the Internet. For details, please consult
your ISP.
Figure 4-2
13

TX-6610
1-Port Gigabit GPON Terminal User Guide
GPON Password
Old Password: Displays the factory default password.
New Password: Enter the password provided by your ISP.
Click Save to make the settings take effect.
GPON SN
Old SN: Displays the factory default SN.
New SN: Enter the SN provided by your ISP.
Click Save to make the settings take effect.
4.3.2 VLAN Setting
Choose “Network Setting”“VLAN Setting”, the VLAN Setting screen will appear on the page as
shown in Figure 4-3.
Figure 4-3
VLAN Mode: Select your desired VLAN Mode from the dropdown list.
Control By OLT: OLT (Optical Line Terminal). In this mode, your ISP can remotely
control the Terminal.
VLAN TAG Mode: In this mode, a VLAN tag will be added to an upstream data without it,
and removed from a downstream data.
Transparent Mode: In this mode, all the upstream and downstream data are forwarded
directly.
Remove DownStream VLAN vid: In this mode, all the upstream data can be remotely
controlled by your ISP, and the VLAN tag of all the downstream data will be removed.
DownStream Transparent Mode: In this mode, all the downstream data are forwarded
directly, and all the upstream data can be remotely controlled by your ISP.
Click Save to make the settings take effect.
VLAN Scan: Click the Start VLAN Scan button to search for available VLAN Mode and
VLAN vid.
14