TP-Link JetStream T2600G-28TS User manual

T2600G-28TS (TL-SG3424)
T2600G-52TS (TL-SG3452)
JetStream Gigabit L2 Managed Switch
REV1.0.0
191001
1257

III
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.

IV
Safety Information
When product has power button, the power button is one of the way to shut off the product;
When there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and
voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被
要求採取某些適當的對策。
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US

III
CONTENTS
Package Contents ............................................................................................................................ 1
Chapter 1 About this Guide ............................................................................................................ 2
1.1 Intended Readers........................................................................................................... 2
1.2 Conventions ................................................................................................................... 2
1.3 Overview of This Guide.................................................................................................. 2
Chapter 2 Introduction .................................................................................................................... 6
2.1 Overview of the Switch................................................................................................... 6
2.2 Appearance Description................................................................................................. 6
2.2.1 Front Panel.......................................................................................................... 6
2.2.2 Rear Panel .......................................................................................................... 8
Chapter 3 Login to the Switch ...................................................................................................... 10
3.1 Login............................................................................................................................. 10
3.2 Configuration.................................................................................................................11
Chapter 4 System ......................................................................................................................... 12
4.1 System Info .................................................................................................................. 12
4.1.1 System Summary.............................................................................................. 12
4.1.2 Device Description ............................................................................................ 14
4.1.3 System Time...................................................................................................... 14
4.1.4 Daylight Saving Time ........................................................................................ 15
4.1.5 System IPv6 ...................................................................................................... 16
4.2 User Management........................................................................................................ 25
4.2.1 User Table ......................................................................................................... 25
4.2.2 User Config ....................................................................................................... 25
4.3 System Tools ................................................................................................................ 26
4.3.1 Boot Config........................................................................................................ 27
4.3.2 Config Restore .................................................................................................. 28
4.3.3 Config Backup ................................................................................................... 28
4.3.4 Firmware Upgrade............................................................................................. 29
4.3.5 System Reboot.................................................................................................. 30
4.3.6 System Reset .................................................................................................... 30
4.4 Access Security............................................................................................................ 31
4.4.1 Access Control .................................................................................................. 31
4.4.2 HTTP Config...................................................................................................... 32
4.4.3 HTTPS Config ................................................................................................... 33
4.4.4 SSH Config........................................................................................................ 35
4.4.5 Telnet Config ..................................................................................................... 42

IV
4.5 SDM Template.............................................................................................................. 42
4.5.1 SDM Template Config ....................................................................................... 42
Chapter 5 Switching ..................................................................................................................... 44
5.1 Port ............................................................................................................................... 44
5.1.1 Port Config ........................................................................................................ 44
5.1.2 Port Mirror.......................................................................................................... 45
5.1.3 Port Security...................................................................................................... 47
5.1.4 Port Isolation ..................................................................................................... 49
5.1.5 Loopback Detection .......................................................................................... 50
5.2 LAG .............................................................................................................................. 52
5.2.1 LAG Table.......................................................................................................... 53
5.2.2 Static LAG.......................................................................................................... 54
5.2.3 LACP Config...................................................................................................... 55
5.3 Traffic Monitor............................................................................................................... 57
5.3.1 Traffic Summary ................................................................................................ 57
5.3.2 Traffic Statistics ................................................................................................. 58
5.4 MAC Address ............................................................................................................... 59
5.4.1 Address Table.................................................................................................... 61
5.4.2 Static Address.................................................................................................... 62
5.4.3 Dynamic Address .............................................................................................. 63
5.4.4 Filtering Address................................................................................................ 65
Chapter 6 VLAN............................................................................................................................ 67
6.1 802.1Q VLAN ............................................................................................................... 68
6.1.1 VLAN Config...................................................................................................... 69
6.1.2 Port Config ........................................................................................................ 70
6.2 Application Example for 802.1Q VLAN........................................................................ 72
6.3 MAC VLAN ................................................................................................................... 73
6.3.1 MAC VLAN ........................................................................................................ 74
6.3.2 Port Enable........................................................................................................ 75
6.4 Application Example for MAC VLAN............................................................................ 75
6.5 Protocol VLAN.............................................................................................................. 77
6.5.1 Protocol Group Table......................................................................................... 78
6.5.2 Protocol Group .................................................................................................. 79
6.5.3 Protocol Template.............................................................................................. 79
6.6 Application Example for Protocol VLAN ...................................................................... 81
6.7 VLAN VPN.................................................................................................................... 83
6.7.1 VPN Config........................................................................................................ 84

V
6.7.2 Port Enable........................................................................................................ 85
6.7.3 VLAN Mapping .................................................................................................. 85
6.8 GVRP ........................................................................................................................... 88
6.9 Private VLAN................................................................................................................ 91
6.9.1 PVLAN Config ................................................................................................... 93
6.9.2 Port Config ........................................................................................................ 94
6.10 Application Example for Private VLAN ........................................................................ 95
Chapter 7 Spanning Tree.............................................................................................................. 98
7.1 STP Config ................................................................................................................. 103
7.1.1 STP Config ...................................................................................................... 103
7.1.2 STP Summary ................................................................................................. 105
7.2 Port Config ................................................................................................................. 106
7.3 MSTP Instance........................................................................................................... 107
7.3.1 Region Config.................................................................................................. 108
7.3.2 Instance Config ............................................................................................... 108
7.3.3 Instance Port Config........................................................................................ 109
7.4 STP Security ...............................................................................................................111
7.4.1 Port Protect ......................................................................................................111
7.4.2 TC Protect ........................................................................................................114
7.5 Application Example for STP Function .......................................................................114
Chapter 8 Multicast......................................................................................................................119
8.1 IGMP Snooping.......................................................................................................... 123
8.1.1 Snooping Config.............................................................................................. 125
8.1.2 Port Config ...................................................................................................... 127
8.1.3 VLAN Config.................................................................................................... 128
8.1.4 Multicast VLAN................................................................................................ 129
8.1.5 Querier Config ................................................................................................. 132
8.1.6 Profile Config................................................................................................... 134
8.1.7 Profile Binding ................................................................................................. 135
8.1.8 Packet Statistics .............................................................................................. 137
8.2 MLD Snooping............................................................................................................ 138
8.2.1 Snooping Config.............................................................................................. 140
8.2.2 Port Config ...................................................................................................... 142
8.2.3 VLAN Config.................................................................................................... 143
8.2.4 Multicast VLAN................................................................................................ 144
8.2.5 Querier Config ................................................................................................. 145
8.2.6 Profile Config................................................................................................... 147

VI
8.2.7 Profile Binding ................................................................................................. 148
8.2.8 Packet Statistics .............................................................................................. 150
8.3 Multicast Table............................................................................................................ 151
8.3.1 IPv4 Multicast Table ........................................................................................ 151
8.3.2 Static IPv4 Multicast Table .............................................................................. 152
8.3.3 IPv6 Multicast Table ........................................................................................ 153
8.3.4 Static IPv6 Multicast Table .............................................................................. 154
Chapter 9 Routing ...................................................................................................................... 156
9.1 Interface ..................................................................................................................... 156
9.2 Routing Table ............................................................................................................. 159
9.3 Static Routing ............................................................................................................. 160
9.4 ARP ............................................................................................................................ 161
9.4.1 ARP Table........................................................................................................ 161
9.4.2 Static ARP........................................................................................................ 161
Chapter 10 QoS............................................................................................................................ 162
10.1 DiffServ....................................................................................................................... 165
10.1.1 Port Priority...................................................................................................... 165
10.1.2 Schedule Mode ............................................................................................... 166
10.1.3 802.1P Priority................................................................................................. 167
10.1.4 DSCP Priority .................................................................................................. 168
10.2 Bandwidth Control...................................................................................................... 170
10.2.1 Rate Limit ........................................................................................................ 170
10.2.2 Storm Control .................................................................................................. 171
10.3 Voice VLAN ................................................................................................................ 172
10.3.1 Global Config................................................................................................... 174
10.3.2 Port Config ...................................................................................................... 175
10.3.3 OUI Config....................................................................................................... 176
Chapter 11 ACL ............................................................................................................................ 178
11.1 Time-Range................................................................................................................ 178
11.1.1 Time-Range Summary .................................................................................... 178
11.1.2 Time-Range Create......................................................................................... 179
11.1.3 Holiday Config ................................................................................................. 180
11.2 ACL Config ................................................................................................................. 180
11.2.1 ACL Summary ................................................................................................. 180
11.2.2 ACL Create...................................................................................................... 181
11.2.3 MAC ACL......................................................................................................... 181
11.2.4 Standard-IP ACL.............................................................................................. 183

VII
11.2.5 Extend-IP ACL ................................................................................................. 184
11.3 Policy Config .............................................................................................................. 185
11.3.1 Policy Summary .............................................................................................. 185
11.3.2 Policy Create ................................................................................................... 186
11.3.3 Action Create................................................................................................... 186
11.4 ACL Binding................................................................................................................ 187
11.4.1 Binding Table................................................................................................... 188
11.4.2 Port Binding..................................................................................................... 189
11.4.3 VLAN Binding .................................................................................................. 190
11.5 Policy Binding............................................................................................................. 190
11.5.1 Binding Table................................................................................................... 191
11.5.2 Port Binding..................................................................................................... 192
11.5.3 VLAN Binding .................................................................................................. 193
11.6 Application Example for ACL ..................................................................................... 193
Chapter 12 Network Security........................................................................................................ 196
12.1 IP-MAC Binding.......................................................................................................... 196
12.1.1 Binding Table................................................................................................... 196
12.1.2 Manual Binding................................................................................................ 197
12.1.3 ARP Scanning ................................................................................................. 199
12.2 DHCP Snooping ......................................................................................................... 200
12.2.1 Global Config................................................................................................... 204
12.2.2 Port Config ...................................................................................................... 205
12.3 ARP Inspection........................................................................................................... 206
12.3.1 ARP Detect...................................................................................................... 209
12.3.2 ARP Defend..................................................................................................... 210
12.3.3 ARP Statistics ...................................................................................................211
12.4 IP Source Guard......................................................................................................... 212
12.5 DoS Defend................................................................................................................ 213
12.5.1 DoS Defend..................................................................................................... 214
12.6 802.1X ........................................................................................................................ 214
12.6.1 Global Config................................................................................................... 218
12.6.2 Port Config ...................................................................................................... 220
12.6.3 Radius Server.................................................................................................. 221
Chapter 13 SNMP......................................................................................................................... 223
13.1 SNMP Config.............................................................................................................. 225
13.1.1 Global Config................................................................................................... 225
13.1.2 SNMP View ..................................................................................................... 226

VIII
13.1.3 SNMP Group ................................................................................................... 227
13.1.4 SNMP User...................................................................................................... 228
13.1.5 SNMP Community........................................................................................... 230
13.2 Notification.................................................................................................................. 232
13.3 RMON......................................................................................................................... 234
13.3.1 Statistics .......................................................................................................... 235
13.3.2 History ............................................................................................................. 236
13.3.3 Event ............................................................................................................... 237
13.3.4 Alarm Config.................................................................................................... 238
Chapter 14 LLDP.......................................................................................................................... 240
14.1 Basic Config ............................................................................................................... 243
14.1.1 Global Config................................................................................................... 243
14.1.2 Port Config ...................................................................................................... 244
14.2 Device Info ................................................................................................................. 245
14.2.1 Local Info......................................................................................................... 245
14.2.2 Neighbor Info................................................................................................... 247
14.3 Device Statistics ......................................................................................................... 248
14.4 LLDP-MED ................................................................................................................. 249
14.4.1 Global Config................................................................................................... 250
14.4.2 Port Config ...................................................................................................... 250
14.4.3 Local Info......................................................................................................... 253
14.4.4 Neighbor Info................................................................................................... 254
Chapter 15 Maintenance .............................................................................................................. 256
15.1 System Monitor .......................................................................................................... 256
15.1.1 CPU Monitor.................................................................................................... 256
15.1.2 Memory Monitor .............................................................................................. 257
15.2 Log.............................................................................................................................. 257
15.2.1 Log Table......................................................................................................... 258
15.2.2 Local Log......................................................................................................... 259
15.2.3 Remote Log..................................................................................................... 260
15.2.4 Backup Log ..................................................................................................... 260
15.3 Device Diagnostics..................................................................................................... 261
15.3.1 Cable Test........................................................................................................ 261
15.4 Network Diagnostics .................................................................................................. 262
15.4.1 Ping ................................................................................................................. 263
15.4.2 Tracert ............................................................................................................. 263
Appendix A. Specifications .................................................................................................. 265

IX
Appendix B. Glossary .......................................................................................................... 266

1
Package Contents
The following items should be found in your box:
One JetStream Gigabit L2 Managed Switch
One power cord
Two mounting brackets and other fittings
Installation Guide
Resource CD for T2600G-28TS/T2600G-52TS, including:
•This User Guide
•CLI Reference Guide
•SNMP Mibs
•802.1X Client Software and its User Guide
•USB Console Driver
•Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.

2
Chapter 1 About this Guide
This User Guide contains information for setup and management of T2600G-28TS/T2600G-52TS
JetStream Gigabit L2 Managed Switch. Please read this guide carefully before operation.
1.1 Intended Readers
This Guide is intended for network managers familiar with IT concepts and network terminologies.
1.2 Conventions
In this Guide the following conventions are used:
The switch or the device mentioned in this Guide stands for T2600G-28TS/T2600G-52TS
JetStream Gigabit L2 Managed Switch without any explanation.
Tips:
The T2600G-28TS and T2600G-52TS are sharing this User Guide. They just differ in the number of
LED indicators and ports. For simplicity, we will take T2600G-28TS for example throughout this
Guide. However, differences with significance will be presented with figures or notes as to attract
your attention.
Menu Name→Submenu Name→Tab page indicates the menu structure. System→System
Info→System Summary means the System Summary page under the System Info menu
option that is located under the System menu.
Bold font indicates a button, a toolbar icon, menu or menu item.
Symbols in this Guide：
Symbol Description
Note: Ignoring this type of note might result in a malfunction or damage to the device.
Tips:
This format indicates important information that helps you make better use of
your device.
1.3 Overview of This Guide
Chapter Introduction
Chapter 1 About This Guide Introduces the guide structure and conventions.
Chapter 2 Introduction
Introduces the features, application and appearance of
T2600G-28TS/T2600G-52TS switch.
Chapter 3 Login to the Switch Introduces how to log on to the Web management page.

3
Chapter Introduction
Chapter 4 System
This module is used to configure system properties of the
switch. Here mainly introduces:

System Info: Configure the description, system time and
network parameters of the switch.
User Management
: Configure the user name and password
for users to log on to the Web management page with a
certain access level.
System Tools: Manage the configuration file of the switch.
Access Security:
Provide different security measures for the
login to enhance the configuration management security.
SDM Template: Manage the hardware TCAM resources.
Chapter 5 Switching
This module is used to configure basic functions of the switch.
Here mainly introduces:
Port: Configure the basic features for the port.

LAG: Configure Link Aggregation Group. LAG is to combine a
number of ports together to make a single high-bandwidth
data path.
Traffic Monitor: Monitor the traffic of each port.
MAC Address: Configure the address table of the switch.
Chapter 6 VLAN
This module is used to configure VLANs to control broadcast in
LANs. Here mainly introduces:
802.1Q VLAN: Configure port-based VLAN.
MAC VLAN: Configure MAC-
based VLAN without changing
the 802.1Q VLAN configuration.

Protocol VLAN: Create VLANs in application layer to make
some special data transmitted in the specified VLAN.
VLAN VPN: VLAN VPN allows the packets with VLAN tags of
private networks to be encapsulated with VLAN tags of public
networks at the network access terminal of the Internet
Service Provider.
GVRP: GVRP
allows the switch to automatically add or
remove the VLANs via the dynamic
VLAN registration
information and propagate the local VLAN registration
information to other switches, without having to individually
configure each VLAN.
Private VLAN:
Designed to save VLAN resources of uplink
devices and decrease broadcast. Private VLAN mainly used
in campus or enterprise networks to achieve user layer-2-
separation and to save VLAN resources of uplink devices.
Chapter 7 Spanning Tree
This module is used to configure spanning tree function of the
switch. Here mainly introduces:

STP Config: Configure and view the global settings of
spanning tree function.
Port Config: Configure CIST parameters of ports.
MSTP Instance: Configure MSTP instances.

STP Security: Configure protection function to prevent
devices from any malicious attack against STP features.

4
Chapter Introduction
Chapter 8 Multicast This module is used to configure multicast function of the switch.
Here mainly introduces:

IGMP Snooping: Configure global parameters of IGMP
Snooping fu
nction, port properties, VLAN and multicast
VLAN.
MLD Snooping: Configure global parameters of MLD
Snooping function, port properties, VLAN and multicast
VLAN.
Multicast Table: View the
information of IPv4 and IPv6
multicast groups already on the switch.
Chapter 9 Routing
The module is used to configure several IPv4 unicast routing
protocols. Here mainly introduces:
Interface: Configure and view different types of interfaces:
VLAN, loopback, routed port and port-channel interface.
Routing table: Displays the routing information summary.
Static Routing: Configure and view static routes.
ARP: Displays the ARP information.
Chapter 10 QoS
This module is used to configure QoS function to provide
different
quality of service for various network applications and
requirements. Here mainly introduces:
DiffServ: Configure
priorities, port priority, 802.1P priority and
DSCP priority.

Bandwidth Control: Configure rate limit feature to control the
traffic rate on
each port; configure storm control feature to
filter broadcast, multicast and UL frame in the network.

Voice VLAN: Configure voice VLAN to transmit voice data
stream within the specified VLAN so as to ensure the
transmission priority of voice data stream and voice quality.
Chapter 11 ACL
This module is used to configure match rules and process
policies of packets to filter packets in order to control the access
of the illegal users to the network. Here mainly introduces:
Time-Range: Configure the effective time for ACL rules.
ACL Config: ACL rules.
Policy Config: Configure operation policies.
ACL Binding: Bind the ACL to a port/VLAN to take its effect on
a specific port/VLAN.
Policy Binding: Bind the policy to a port/VLAN to take its
effect on a specific port/VLAN.

5
Chapter Introduction
Chapter 12 Network Security
This module is used to configure the protection measures for the
network security. Here mainly introduces:
IP-MAC Binding: Bind the IP address, MAC address, VLAN
ID and the connected Port number of the Host together.
DHCP Snooping:
DHCP Snooping functions to monitor the
process of the Host obtaining the IP address from DHCP
server, and record the IP address, MAC address, VLAN and
the connected Port number of the Host for automatic binding.

ARP Inspection: Configure ARP inspection feature to prevent
the network from ARP attacks.

IP Source Guard: Configure IP source guard feature to filter
IP packets in the LAN.
DoS Defend: Configure DoS defend feature to prevent DoS
attack.

802.1X: Configure common access control mechanism for
LAN ports to solve mainly authentication and security
problems.
Chapter 13 SNMP
This module is used to configure SNMP function to provide a
management frame
to monitor and maintain the network
devices. Here mainly introduces:
SNMP Config: Configure global settings of SNMP function.

Notification: Configure notification function for the
management station to monitor and process the events.
RMON: Configure RMON f
unction to monitor network more
efficiently.
Chapter 14 LLDP
This module is used to configure LLDP function to provide
information for SNMP applications to simplify troubleshooting.
Here mainly introduces:
Basic Config: Configure the LLDP parameters of the device.

Device Info: View the LLDP information of the local device
and its neighbors.
Device Statistics: View the LLDP statistics of the local device.
LLDP-MED: Configure the LLDP-MED features.
Chapter 15 Maintenance This module is used to assemble the commonly used system
tools to manage the switch. Here mainly introduces:
System Monitor: Monitor the memory and CPU of the switch.
Log: View configuration parameters on the switch.
Device Diagnostics:
Test the connection status of the cable
connected to the switch, test if the port of the switch and the
connected device are available.
Network Diagnostics
: Test if the destination is reachable and
the account of router hops from the switch to the destination.
Appendix A Specifications Lists the hardware specifications of the switch.
Appendix B Glossary Lists the glossary used in this manual.
Return to CONTENTS

6
Chapter 2 Introduction
Thanks for choosing the T2600G-28TS/T2600G-52TS JetStream Gigabit L2 Managed Switch!
2.1 Overview of the Switch
Designed for workgroups and departments, T2600G-28TS/T2600G-52TS from TP-LINK provides
wire-speed performance and full set of L2 and L2+ management features. It provides a variety of
service features and multiple powerful functions with high security.
The EIA-standardized framework and smart configuration capacity can provide flexible solutions
for a variable scale of networks. QoS and IGMP/MLD snooping/filtering optimize voice and video
application. Link aggregation (LACP) increase aggregated bandwidth, optimizing the transport of
business critical data. SNMP/SNMPv6, RMON, WEB/CLI Log-in bring abundant management
policies.
T2600G-28TS/T2600G-52TS switch integrates multiple functions with excellent
performance, and is friendly to manage, which can fully meet the need of the users demanding
higher networking performance.
2.2 Appearance Description
2.2.1 Front Panel
The front panel of T2600G-28TS is shown as Figure 2-1.
Figure 2-1 Front Panel of T2600G-28TS
The following parts are located on the front panel of T2600G-28TS:
LEDs
Name Status Indication
PWR
On The switch is powered on.
Flashing Power supply is abnormal.
Off The switch is powered off or power supply is abnormal.
SYS
Flashing The switch works properly.
On/Off The switch works improperly.
1000Mbps
On
A 1000Mbps device is connected to the corresponding
port but no activity.
Off No device is connected to the corresponding port.
Link/Act
On
A device is linked to the corresponding port and
running properly.
Flashing Data is being transmitted or received.
Off No device is linked to the corresponding port.

7
Console (RJ-45) Port
Designed to connect with the serial port of a computer or terminal for monitoring and configuring
the switch.
Console (USB) Port
Designed to connect with the USB port of a computer for monitoring and configuring the switch.
The switch has an RJ-45 console port and a micro-USB console port available. Console input is
active on only one console port at a time. By default, the micro-USB connector takes precedence
over the RJ-45 connector.
10/100/1000Mbps RJ45 Port
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each
10/100/1000Mbps RJ45 port has a corresponding 1000Mbps LED and Link/Act LED.
SFP Port
Designed to install the SFP module. T2600G-28TS features 4 individual SFP ports and supports
1000M SFP module connection only.
The front panel of T2600G-52TS is shown as Figure 2-2.
Figure 2-2 Front Panel of T2600G-52TS
The following parts are located on the front panel of T2600G-52TS:
Console (USB) Port
Designed to connect with the USB port of a computer for monitoring and configuring the switch.
The switch has an RJ-45 console port and a micro-USB console port available. Console input is
active on only one console port at a time. By default, the micro-USB connector takes precedence
over the RJ-45 connector.
Console (RJ-45) Port
Designed to connect with the serial port of a computer or terminal for monitoring and configuring
the switch.
LEDs
Name Status Indication
PWR
On Power is on.
Flashing Power supply is abnormal.
Off Power is off or power supply is abnormal.
SYS
Flashing The switch works properly.
On/Off The switch works improperly.

8
Name Status Indication
10/100/1000
Mbps (port
1-48)
Green
On
A 1000Mbps device is connected to the corresponding
port but no activity.
Flashing
A 1000Mbps device is connected to the corresponding
port and data is being transmitted or received.
Yellow
On
A 10/100Mbps device is connected to the
corresponding port but no activity.
Flashing
A 10/100Mbps device is connected to the
corresponding port and d
ata is being transmitted or
received.
Off No device is connected to the corresponding port.
Link/Act
(port 49-52)
On
There is a device linked to the corresponding SFP port
but no activity.
Flashing
The corresponding SFP port is transmitting or
receiving data.
Off
There is no device linked to the corresponding SFP
port.
10/100/1000Mbps RJ45 Port
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each
10/100/1000Mbps RJ45 port has a corresponding 1000Mbps LED.
SFP Port
Designed to install the SFP module. T2600G-52TS features 4 individual SFP ports and supports
1000M SFP module connection only.
Port Feature
Model 10/100/1000Mbps RJ45 Port SFP Port Console Port
T2600G-28TS 24 4 2
T2600G-52TS 48 4 2
2.2.2 Rear Panel
The rear panel of T2600G-28TS/T2600G-52TS features a Kensington security slot, a Grounding
Terminal (marked with ) and a power socket.
Figure 2-3 Rear Panel
Kensington Security Slot: Secure the lock (not provided) into the security slot to prevent the
device from being stolen.

9
Grounding Terminal: The switch already comes with lightning protection mechanism. You can
also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground
Cable.
AC Power Socket: Connect the female connector of the power cord here, and the male
connector to the AC power outlet.
Return to CONTENTS

10
Chapter 3 Login to the Switch
3.1 Login
1) To access the configuration utility, open a web-browser and type in the default address
http://192.168.0.1 in the address field of the browser, then press the Enter key.
Figure 3-1 Web-browser
Tips:
To log in to the switch, the IP address of your PC should be set in the same subnet addresses of
the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is
255.255.255.0.
2) After a moment, a login window will appear, as shown in Figure 3-2. Enter admin for the User
Name and Password, both in lower case letters. Then click the Login button or press the Enter
key.
Figure 3-2 Login