TP-Link Jetstream L2 TL-SG5412F User manual

Business Networking Solution
Installation Guide
Jetstream L2 Managed Switch

About this Installation Guide
This Installation Guide describes the hardware characteristics, installation methods and the
points that should be attended to during the installation. This Installation Guide is structured as
follows:
Chapter 1 Introduction
This chapter describes the external components of the switch.
Chapter 2 Installation
This chapter illustrates how to install the switch.
Chapter 3 Connection
This chapter illustrates how to do the physical connection of the switch.
Appendix A Troubleshooting
Appendix B Hardware Specifications
Audience
This Installation Guide is for:
Network Engineer Network Administrator
Conventions
• Some models featured in this guide may be unavailable in your country or region. For local sales
information, visit https://www.tp-link.com.
• The figures in Chapter 2 and Chapter 3 are for demonstration purposes only. Your switch may
differ in appearance from that depicted.
• This guide uses the specific formats to highlight special messages. The following table lists the
notice icons that are used throughout this guide.
Remind to be careful. A caution indicates a potential which may result in device damage.
Remind to take notice. The note contains the helpful information for a better use of the
product.
Related Document
The User Guide and CLI Reference Guide of the product are provided on the resource CD. To
obtain the latest product information, visit the official website:
https://www.tp-link.com

Contents
Chapter 1 Introduction ——————————— 01
1.1 Product Overview ...........................................................01
1.2 Appearance.......................................................................01
Chapter 2 Installation ——————————— 08
2.1 Package Contents ..........................................................08
2.2 Safety Precautions .........................................................08
2.3 Installation Tools..............................................................10
2.4 Product Installation ........................................................11
Chapter 3 Connection ——————————— 13
3.1 Ethernet Port ....................................................................13
3.2 SFP Port..............................................................................13
3.3 Console Port .....................................................................13
3.4 Verify Installation.............................................................14
3.5 Power On............................................................................15
3.6 Initialization........................................................................16
3.7 Accessing the Switch....................................................16
Appendix A Troubleshooting ———————— 17
Appendix B Hardware Specications ————— 18

JetStream L2 Managed Switch
01Introduction
Chapter 1 Introduction
1.1 Product Overview
Designed for workgroups and departments, TP-Link JetStream L2 Managed Switch provides wire-
speed performance and abundant L2 management features. It provides a variety of service features
and multiple powerful functions with high security.
The EIA-standardized framework and smart configuration capacity can provide flexible solutions
for a variable scale of networks. ACL, 802.1x and Dynamic ARP Inspection provide robust security
strategies. QoS and IGMP snooping/filtering optimize voice and video application. Link aggregation
(LACP) increases aggregated bandwidth, optimizing the transport of business critical data. SNMP,
RMON, WEB and CLI Log-in bring abundant management policies. TP-Link JetStream L2 Managed
Switch integrates multiple functions with excellent performance, and is friendly to manage, which
can fully meet the need of the users demanding higher networking performance.
T2500G-10MPS/T2600G-28MPS is also a Power Sourcing Equipment (PSE*). All the RJ45 ports on
the switch support Power over Ethernet (PoE*) function, which can automatically detect and supply
power to those powered devices (PDs*) complying with IEEE 802.3af and IEEE 802.3at.
*PSE: a device (switch or hub for instance) that provides power through an Ethernet cable.
*PoE: This technology describes a system to transmit electrical power, along with data, to remote
devices over standard twisted-pair cable in an Ethernet.
*PD: a device powered by a PSE and thus consumes energy. Examples include powering network
cameras, wireless LAN access points, IP telephones, network hubs, embedded computers etc.
1.2 Appearance
■Front Panel
The front panel of TL-SG5412F is shown as the following figure.
Figure 1-1 Front Panel of TL-SG5412F
LEDs Console Port
SFP Port 10/100/1000Mbps RJ45 Port
The front panel of T2500G-10TS is shown as the following figure.
Figure 1-2 Front Panel of T2500G-10TS
LEDs SFP Port
10/100/1000Mbps
RJ45 Port
Console Port
(RJ-45/USB)

JetStream L2 Managed Switch
02 Introduction
The front panel of T2500G-10MPS is shown as the following figure.
Figure 1-3 Front Panel of T2500G-10MPS
LEDs SFP Port10/100/1000Mbps
RJ45 Port
Console Port
(RJ-45/USB)
LED Mode
Switch Button
The front panel of T2500-28TC is shown as the following figure.
Figure 1-4 Front Panel of T2500-28TC
LEDs 10/100Mbps RJ45 Port SFP Port
10/100/1000Mbps RJ45 Port
Console Port
The front panel of T2600G-18TS is shown as the following figure.
Figure 1-5 Front Panel of T2600G-18TS
10/100/1000Mbps
RJ45 Port
LEDs Console Port
(RJ45/USB)
SFP Port
The front panel of T2600G-28TS is shown as the following figure.
Figure 1-6 Front Panel of T2600G-28TS
T2600G-28TS
10/100/1000Mbps
RJ45 Port
LEDs Console Port
(RJ45/USB)
SFP Port
The front panel of T2600G-28TS-DC is shown as the following figure.
Figure 1-7 Front Panel of T2600G-28TS-DC
T2600G-28TS-DC
10/100/1000Mbps
RJ45 Port
LEDs Console Port
(RJ45/USB)
SFP Port

JetStream L2 Managed Switch
03Introduction
The front panel of The T2600G-28MPS is shown as the following figure.
Figure 1-8 Front Panel of T2600G-28MPS
10/100/1000Mbps
RJ45 Port
LEDs Console Port
(RJ45/USB)
SFP Port
LEDMode
Switch Button
The front panel of The T2600G-28SQ is shown as the following figure.
Figure 1-9 Front Panel of T2600G-28SQ
PWR
SYS
FAN
2 4 6 8 10 12 14 16 18 20 22 24
26
28
1 3 5 7 9 11 13 15 17 19 21 23 25
27
1000Mbps
Link/Act
Console(RJ-45)
Console(USB)
3 5 7
84 62
1 11 13 15
1612 1410
9 19 21 23
2420 22
21T 23T SFP+
24T22T18
17
25 26 27 28
activity
10Gbps
1Gbps
10/100/1000Mbps
RJ45 Port
LEDs Console Port
(RJ45/USB)
SFP+ PortSFP Port
The front panel of The T2600G-52TS is shown as the following figure.
Figure 1-10 Front Panel of T2600G-52TS
ConsoleConsole(USB)
10/100/1000Mbps
RJ45 Port
LEDs
Console Port
(RJ45/USB)
SFP Port
LEDs
For TL-SG5412F/T2500G-10TS/T2500-28TC/T2600G-18TS/T2600G-28TS/T2600G-28TS-DC/
T2600G-28SQ / T2600G-52TS
LED Indication
Power
PWR
Note: Power for T2500-28TC and PWR for the other switches.
On: The switch is powered on.
Off: The switch is powered off or power supply is abnormal.
Flashing: Power supply is abnormal.
System
SYS
Note: System for T2500-28TC and SYS for the other switches.
Flashing: The switch works properly.
On or Off: The switch works improperly.
FAN
Note: Only for T2600G-28SQ.
Green On: The fan works normally.
Yellow On: The fan works abormally.

JetStream L2 Managed Switch
04 Introduction
LED Indication
10/100M
Note: Only for ports1-24 of T2500-28TC.
Green On: Running at 100Mbps, but no activity.
Green Flashing: Running at 100Mbps and is transmitting or receiving data.
Yellow On: Running at 10Mbps, but no activity.
Yellow Flashing: Running at 10Mbps and is transmitting or receiving data.
Off: No device is linked to the corresponding port.
1000M
10/100/1000M
10/100/1000BASE-T
Note: 1000M for ports25-28 of T2500-28TC, 10/100/1000M for T2500G-10TS and
ports 1-48 of T2600G-52TS, 10/100/1000Base-T for ports 9T-12T of TL-SG5412F.
Green On: Running at 1000Mbps, but no activity.
Green Flashing: Running at 1000Mbps and is transmitting or receiving data.
Yellow On: Running at 10/100Mbps, but no activity.
Yellow Flashing: Running at 10/100Mbps and is transmitting or receiving data.
Off: No device is linked to the corresponding port.
1000Mbps
Note: For TL-SG5412F/T2600G-18TS/T2600G-28TS/T2600G-28TS-DC and
ports1-24 of T2600G-28SQ.
On: Running at 1000Mbps.
Off: Running at 10/100Mbps or no device is linked to the corresponding port.
Link/Act
For TL-SG5412F/T2600G-18TS/T2600G-28TS/T2600G-28TS-DC/ T2600G-52TS
and ports 1-24 of T2600G-28SQ:
On: A device is linked to the corresponding port and running properly.
Flashing: Transmitting or receiving data.
Off: No device is linked to the corresponding port.
For ports 25-28 of T2600G-28SQ:
Green On: Running at 10Gbps, but no activity.
Green Flashing: Running at 10Gbps and is transmitting or receiving data.
Yellow On: Running at 1000Mbps, but no activity.
Yellow Flashing: Running at 1000Mbps and is transmitting or receiving data.
Off: No device is linked to the corresponding port.
SFP1, SFP2
Note: Only for T2500G-10TS.
Green On: A 1000Mbps device is linked to the corresponding port, but no activity.
Green Flashing: A 1000Mbps device is linked to the corresponding port and data is
being transmitted or received.
Yellow On: A 100Mbps device is linked to the corresponding port, but no activity.
Yellow Flashing: A 100Mbps device is linked to the corresponding port and is
transmitting or receiving data.
Off: No device is linked to the corresponding port but no activity.
For T2500G-10MPS/T2600G-28MPS
T2500G-10MPS/T2600G-28MPS has an LED mode switch button which is used to switch the LED
status indication. When the Speed LED is on, the port LED is indicating the data transmission rate.
When the PoE LED is on, the port LED is indicating the power supply status. By default the Speed LED

JetStream L2 Managed Switch
05Introduction
is on. Pressing the mode switch button, the Speed LED will turn off and the PoE LED will light up. Then
the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again.
LED Indication
PWR
On: The switch is powered on.
Off: The switch is powered off or power supply is abnormal.
Flashing: Power supply is abnormal.
SYS Flashing: The switch works properly.
On or Off: The switch works improperly.
FAN
Green: All the fans work properly.
Yellow: Not all the fans work properly.
Off: The switch works improperly.
PoE Max
(When the PoE LED
is on)
On: The remaining PoE power is equal to or less than 7W.
Flashing: The remaining PoE power is equal to or less than 7W and lasts for more than
2 minutes.
Off: The remaining PoE power is larger than 7W.
Speed or PoE
(When the Speed
LED is on)
Green On: Running at 1000Mbps, but no activity.
Green Flashing: Running at 1000Mbps and is transmitting or receiving data.
Yellow On: Running at 10/100Mbps, but no activity.
Yellow Flashing: Running at 10/100Mbps and is transmitting or receiving data.
Off: No device is linked to the corresponding port.
Speed or PoE
(When the PoE LED
is on)
Green On: The port is supplying power normally.
Green Flashing: The supply power exceeds the correponding port's maximum power.
Yellow On: Overload or short circuit is detected.
Yellow Flashing: Power-on self-test failed.
Off: Not providing PoE power on the port.
SFP
SFP1, SFP2
Note: SFP1 and SFP2 for T2500G-10MPS, SFP for T2600G-28MPS
Green On: A 1000Mbps device is linked to the corresponding port, but no activity.
Green Flashing: A 1000Mbps device is linked to the corresponding port and data is
being transmitted or received.
Yellow On: A 100Mbps device is linked to the corresponding port, but no activity.
Yellow Flashing: A 100Mbps device is linked to the corresponding port and is
transmitting or receiving data.
Off: No device is linked to the corresponding port.
Console Port (RJ-45/USB)
Designed to connect with a computer for monitoring and configuring the switch. For T2500G-10TS/
T2500G-10MPS/T2600G-18TS/T2600G-28TS/T2600G-28TS-DC/T2600G-28MPS/
T2600G-28SQ/T2600G-52TS, the switch has an RJ-45 console port and a micro-USB console port.
Console input is active on only one console port at a time. By default, the micro-USB connector takes
precedence over the RJ-45 connector.
10/100Mbps RJ45 Port
Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps.

JetStream L2 Managed Switch
06 Introduction
10/100/1000Mbps RJ45 Port
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. For
T2500G-10MPS/T2600G-28MPS, the port can also provide power for PDs.
SFP Port
Designed to install the 1Gbps SFP module. For T2600G-28SQ, ports 17-24 also support 100Mbps
SFP module.
SFP+ Port
Designed to install the 10Gbps SFP+ module.
Combo Ports
A Combo port consists of one RJ45 port and one SFP port, and they share the same port ID. The
SFP port and the associated RJ45 port cannot work simultaneously. If both of the two ports are
connected, only the SFP port works.
For T2500-28TC, RJ45 ports 25-28 and SFP ports 25-28 are combo ports; For T2600G-28SQ, RJ45
ports 21-24 and SFP ports 21-24 are combo ports.
Port Feature
Model 10/100/1000Mbps
RJ45 Port
10/100Mbps RJ45
Port SFP Port SFP+ Port Console Port
TL-SG5412F 4 0 12 0 1
T250 0G-10TS 8 0 2 0 2
T2500-28TC 424 4 0 1
T250 0G-10M PS 8 0 2 0 2
T2600 G-18TS 16 0 2 0 2
T2600G-28TS 24 0 4 0 2
T2600G-28TS-DC 24 0 4 0 2
T2600G-28MPS 24 0 4 0 2
T2600G-28SQ 4 0 24 4 2
T2600G-52TS 48 0 4 0 2
■Rear Panel
For TL-SG5412F/T2500G-10TS/T2500G-10MPS/T2500-28TC/T2600G-18TS/T2600G-28TS/
T2600G-28MPS/T2600G-28SQ/ T2600G-52TS
The rear panel is shown as the following figure. Here we take T2600G-28TS as an example.
Figure 1-11 Rear Panel of T2600G-28TS
100-240V~50/60Hz 0.5A
Power Socket
Grounding Terminal
Kensington Security slot

JetStream L2 Managed Switch
07Introduction
For T2600G-28TS-DC
The rear panel is shown as the following figure.
Figure 1-12 Rear Panel of T2600G-28TS-DC
DC Power Input
Grounding Terminal
Kensington Security slot
Kensington Security Slot
Secure the lock (not provided) into the security slot to prevent the device from being stolen.
Note:
TL-SG5412F/T2500-28TC does not have a kensington security slot.
Grounding Terminal
The switch already comes with lightning protection mechanism. You can also ground the switch
through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed lightning
protection measures, go to https://www.tp-link.com/support, search the model number of your
switch and go to the product Support web page, refer to the Lightning Protection Guide from the
Related Documents:
https://www.tp-link.com/us/configuration-guides/lightning_protection_guide/
Power Socket
Plug the negative connector of the power cord directly into the power socket and plug the positive
connector into an AC power outlet. Make sure that the voltage of the power supply meets the
requirement of the input voltage (100-240V~ 50/60Hz).
Note:
You should use the provided power cord.
DC Power Input
Attach the power wires to the DC power input. We recommend you use 22-14 AWG wires. Connect
the positive pole of the DC power supply to the "+" end, and the negative pole to the "-" end. Make
sure the power supply meets the requirement of the input (18-48V 1.2A). A disconnecting device
like an isolating switch shall be installed and easily accessible. The disconnecting device shall have a
contact separation at least equal to the minimum clearance for basic insulation.
Note:
The power wires and disconnecting device are not included with our product. If needed, you
can purchase them separately.

JetStream L2 Managed Switch
08 Installation
Chapter 2 Installation
2.1 Package Contents
Make sure that the package contains the following items. If any of the listed items is damaged or
missing, contact your distributor.
One Power Cord, One Console
Cable and One USB Cable
One Switch Installation Guide
Installation Guide
BusinessNetworking Solution
Two mounting brackets, eight
screws and four rubber feet
One Resouce CD
Note:
The USB Cable is not provided with TL-SG5412F/T2500-28TC. The power cord is not provided
with T2600G-28TS-DC.
2.2 Safety Precautions
To avoid any device damage and bodily injury caused by improper use, you should observe the
following rules.
■Safety Precautions
■Keep the power off during the installation.
■Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good skin contact and is
well grounded.
■Use only the power cord provided with the switch.
■Make sure that the supply voltage matches the specifications indicated on the rear panel of the
switch.
■Ensure that the switch is installed in a well-ventilated environment and its ventilation hole is not
blocked.
■Do not open or remove the cover of the switch.
■Before cleaning the device, cut off the power supply. Do not clean it by the waterish cloth, and never
use any other liquid cleaning method.
■Place the device with its bottom surface downward.

JetStream L2 Managed Switch
09Installation
■Site Requirements
Temperature/Humidity
40℃
0℃
Keep the equipment room at an appropriate level of temperature and humidity. Too much or too
little humidity may lead to bad insulation, leakage of electricity, mechanical property changes,
and corrosion. High temperatures may accelerate aging of the insulation materials, significantly
shortening the service life of the device. To find out the best temperature and humidity conditions
for the device, check the following table.
Environment Temperature Humidity
Operating 0℃to 40℃10% to 90%RH Non-condensing
Storage -40℃to 70℃5% to 90%RH Non-condensing
Clearness
The dust accumulated on the switch can be absorbed by static electricity and result in poor contact
of metal contact points. Some measures have been taken for the device to prevent static electricity,
but too strong static electricity can cause deadly damage to the electronic elements on the internal
circuit board. To avoid the effect of static electricity on the operation of the Switch, attach much
importance to the following items:
■Dust the device regularly, and keep the indoor air clean.
■Keep the device well grounded and ensure that the static electricity has been transferred.
Electromagnetic Interference
Electronic elements including capacitance and inductance on the device can be affected by external
interferences, such as conducted emission by capacitance coupling, inductance coupling, and
impedance coupling. To decrease the interferences, make sure to take the following measures:
■Use the power supply that can effectively filter interference from the power grid.
■Keep the device far from high-frequency and strong-current devices such as radio transmitting
station.
■Use electromagnetic shielding when necessary.

JetStream L2 Managed Switch
10 Installation
Lightning Protection
Extremely high voltage currents can be produced instantly when lightning occurs and the air in the
electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong
enough to damage electronic devices, more effective lightning protection measures should be
taken.
■Ensure that the rack and the device are well earthed.
■Make sure the power socket has a good contact with the ground.
■Keep a reasonable cabling system and avoid induced lightning.
■Use the signal SPD (Surge Protective Device) when wiring outdoor.
Note:
For detailed lightning protection measures, go to https://www.tp-link.com/support, search
the model number of your switch and go to the product Support web page, refer to the
Lightning Protection Guide from the Related Documents:
https://www.tp-link.com/us/conguration-guides/lightning_protection_guide/
Installation Site
When installing the device on a rack or a flat workbench, attach much importance to the following
items:
■The rack or workbench is flat, stable, and sturdy enough to support the weight of 5.5 kg at least.
■The rack or workbench has a good ventilation system. The equipment room is well ventilated.
■The rack is well grounded. Keep the device less than 1.5 meters away from the power socket.
2.3 Installation Tools
■Phillips screwdriver
■ESD-preventive wrist wrap
■Cables
Note:
These tools are not included with our product. If needed, you can purchase them separately.

JetStream L2 Managed Switch
11Installation
2.4 Product Installation
■Desktop Installation
To install the device on the desktop, follow the steps:
1. Set the device on a flat surface which is strong enough to support the entire weight of the device
with all fittings.
2. Remove the adhesive backing papers from the rubber feet.
3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at
each corner of the device.
Figure 2-1 Desktop Installation
Feet
Bottom of the Device
Notch
■Rack Installation
To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below:
1. Check the efficiency of the grounding system and the stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws, as
illustrated in the following figure.
Figure 2-2 Bracket Installation
Rack-mounting Bracket
Screw

JetStream L2 Managed Switch
12 Installation
3. After the brackets are attached to the device, use suitable screws (not provided) to secure the
brackets to the rack, as illustrated in the following figure.
Figure 2-3 Rack Installation
Rack
Caution:
■Leave 5 to 10 cm gaps around the devices for air circulation.
■Avoid placing heavy things on the device.
■Mount devices in sequence from the bottom to top of the rack and ensure a certain clearance
between devices for the purpose of heat dissipation.

JetStream L2 Managed Switch
13Connection
Chapter 3 Connection
3.1 Ethernet Port
Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shows.
Figure 3-1 Connecting the RJ45 Port
RJ45 Port
RJ45 Cable
3.2 SFP Port
The following figure demonstrates the connection of SFP port to an SFP module.
Figure 3-2 Inserting the SFP Module
SFP Slot
SFP Module
3.3 Console Port
CLI (Command Line Interface) enables you to manage the switch, thus you can load the CLI after
connecting the PCs or Terminals to the console port on the switch via the provided cable.

JetStream L2 Managed Switch
14 Connection
Connect the Console (RJ-45) port of the device with your computer by the console cable as the
following figure shows.
Figure 3-3 Connecting the Console (RJ-45) Port
Console(RJ45)
Connect the Console (USB) port of the device with your computer by the USB cable as the following
figure shows.
Figure 3-4 Connecting the Console (USB) Port
T2600G-28TS
Console(USB)
Note:
■Console (RJ-45) port and Console (USB) port cannot be used concurrently. Console (USB)
port takes priority over the Console (RJ-45) port.
■The Console (USB) port is hot-pluggable while the Console (RJ-45) port is not. Keep the
device power off when plugging the console cable into the Console (RJ-45) port.
■Do not connect the console port with other ports by RJ45 cable.
■TL-SG5412F and T2500-28TC do not have a Console (USB) port.
3.4 Verify Installation
After completing the installation, verify the following items:
■There should be 5 to 10 cm of clearance around the device for ventilation and make sure the air flow
is adequate.
■The voltage of the power supply meets the requirement of the input voltage of the device.
■The power socket, device and rack are well grounded.
■The device is correctly connected to other network devices.

JetStream L2 Managed Switch
15Connection
3.5 Power On
For TL-SG5412F/T2500G-10TS/T2500G-10MPS/T2500-28TC/T2600G-18TS/T2600G-28TS/
T2600G-28MPS/T2600G-28SQ/ T2600G-52TS
Plug the negative connector of the power cord directly into the power socket and plug the positive
connector into an AC power outlet as the following figure shows. Make sure that the voltage of the
power supply meets the requirement of the input voltage (100-240V~ 50/60Hz).
Figure 3-5 Connecting to the Power Supply
100-240V~50/60Hz 0.5A
Note:
The gure is to illustrate the application and principle. The provided plug and the socket in your
region may dier from the gures above.
For T2600G-28TS-DC
Attach the power wires to the DC power input as the following figure shows. We recommend you use
22-14 AWG wires. Connect the positive pole of the DC power supply to the "+" end, and the negative
pole to the "-" end. Make sure the power supply meets the requirement of the input (18-48V 1.2A). A
disconnecting device like an isolating switch shall be installed and easily accessible. The
disconnecting device shall have a contact separation at least equal to the minimum clearance for
basic insulation.
Figure 3-6 Connecting to the Power Supply
To a disconnecting de
vice
and DC power supply
Note:
The figure is to illustrate the application and principle. The power wires and disconnecting
device are not included with our product. If needed, you can purchase them separately.

JetStream L2 Managed Switch
16 Connection
3.6 Initialization
After the device is powered on, it begins the Power-On Self-Test. A series of tests run automatically
to ensure the device functions properly. During this time, its LED indicators will respond in the
following order:
1. The PWR LED indicator lights on all the time. The SYS LED and the LED indicators of all the ports
keep off.
2. After about one minute, the SYS LED and LED indicators of all the ports will flash momentarily and
then turn off.
3. Several seconds later, the SYS LED indicator will flash, which represents a successful initialization.
3.7 Accessing the Switch
After the initialization finished, you can access and manage the switch using the GUI (Graphical User
Interface) or using the CLI (Command Line Interface).
■To access the switch using the GUI, open a web browser and type the default management address
http://192.168.0.1 in the address field, then press the Enter key. The default Username and Password
are both admin in lower case letters.
■To access the switch using the CLI, you can use the Console port, Telnet and SSH connection. When
using the Console port, start the terminal emulation program (such as the Hyper Terminal) on the PC
and configure the terminal emulation program as follows:
Baud Rate Data Bits Parity Stop Bits Flow Control
38400bps 8None 1None
For the detailed configurations, refer to the Configuration Guide and CLI Reference Guide. The two
guides can both be found on the resource CD or on the download center of our official website:
https://www.tp-link.com/en/download-center.html.