TP-Link ES20M User manual

Button Explanations
LED Status
Smart Wi-Fi Dimmer Switch
Quick Start Guide
7106509394 REV1.1.0 ©2022 TP-Link
Specications
Rating: 120V~ 60Hz
Load: 300W Incandescent, 150W LED
Operation temperature: 0~40℃
Method of mounting included: Independently mounted
(Vertically position only);
Operating control, Type 1 action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1
Need some help?
?
Visit www.tp-link.com/support
for technical support, user guides, FAQs,
warranty & more
Flashing amber
Flashing green
White
Solid red
Stay green for 30s
Flashing amber & green
Connecting to Wi-Fi.
Ready for setup.
Device resetting.
Light fixture is off.
Disconnected from Wi-Fi.
Connected to Wi-Fi.
*Images may dier from your actual product.
Restart
Reset
Press and hold for about 5s to reset
Wi-Fi while keeping other settings.
Press to restart your switch.
Decrease or increase the brightness.
Press and hold for about 10s to restore
your switch to factory default settings.
/
Set Up Your Switch Appearance
STEP 2 SET UP
Tap the button in the app and select Smart
Switches. Then follow the step-by-step app
instructions to set up your smart dimmer
switch.
DOWNLOAD APP
Get the Kasa Smart app from the App Store or
Google Play.
STEP 1
OR
Safety Notice
Before installing, servicing or removing the switch, read and follow all
safety precautions including the following:
• CAUTION – Risk of Electric Shock – More than one disconnect switch
may be required to de-energize the equipment before servicing. A
circuit breaker which disconnects the Line and Neutral conductor
simultaneously is suitable. Ensure power is o at the circuit breaker
before removing or installing any switch. Use a non-contact voltage
tester to ensure the power is o.
• The Smart Switch must be installed and used in accordance with the
National Electric Code (NEC) or your local electrical code. If you are
unfamiliar with these codes and requirements, or are uncomfortable
performing the installation, consult a qualied electrician.
• Do not install the Smart Switch with wet hands or when standing on wet
or damp surfaces.
• Install only in a suitable UL Listed outlet box (suitable dimensions: H >
2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).
• Tighten terminal screws to 13 lbf-in.
High Voltage-Disconnect power supply before servicing
CAUTION
On/O
Button
Dimmer
Buttons
Motion
Sensor
Restart
LED
Reset
Ambient
Light
Sensor

Product Introduction Wire Your Switch
Built-in motion and ambient light sensors
work together to realize hands-free control.
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to a dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the Ground and Neutral wires.
1
2
Identify Line and Load wires.
3Line up the switch with the mounting
holes. Secure it with screws.
5Attach the wallplate. Then the wiring is
nished.
6
Flip the page over to complete setup.
Power
Source
To Light
1) Turn on the circuit breaker. Use a voltage detector
to identify the energized wire (Line wire).
2) Turn o the circuit breaker. Label the Line and Load
wires.
Take care to avoid electric shocks.
Load wireLine wire

Product Introduction Wire Your Switch
Built-in motion and ambient light sensors
work together to realize hands-free control.
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to a dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the Ground and Neutral wires.
1
2
Identify Line and Load wires.
3Line up the switch with the mounting
holes. Secure it with screws.
5Attach the wallplate. Then the wiring is
nished.
6
Flip the page over to complete setup.
Power
Source
To Light
1) Turn on the circuit breaker. Use a voltage detector
to identify the energized wire (Line wire).
2) Turn o the circuit breaker. Label the Line and Load
wires.
Take care to avoid electric shocks.
Load wireLine wire

Product Introduction Wire Your Switch
Built-in motion and ambient light sensors
work together to realize hands-free control.
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to a dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the Ground and Neutral wires.
1
2
Identify Line and Load wires.
3Line up the switch with the mounting
holes. Secure it with screws.
5Attach the wallplate. Then the wiring is
nished.
6
Flip the page over to complete setup.
Power
Source
To Light
1) Turn on the circuit breaker. Use a voltage detector
to identify the energized wire (Line wire).
2) Turn o the circuit breaker. Label the Line and Load
wires.
Take care to avoid electric shocks.
Load wireLine wire

Product Introduction Wire Your Switch
Built-in motion and ambient light sensors
work together to realize hands-free control.
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to a dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the Ground and Neutral wires.
1
2
Identify Line and Load wires.
3Line up the switch with the mounting
holes. Secure it with screws.
5Attach the wallplate. Then the wiring is
nished.
6
Flip the page over to complete setup.
Power
Source
To Light
1) Turn on the circuit breaker. Use a voltage detector
to identify the energized wire (Line wire).
2) Turn o the circuit breaker. Label the Line and Load
wires.
Take care to avoid electric shocks.
Load wireLine wire

Product Introduction Wire Your Switch
Built-in motion and ambient light sensors
work together to realize hands-free control.
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to a dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the Ground and Neutral wires.
1
2
Identify Line and Load wires.
3Line up the switch with the mounting
holes. Secure it with screws.
5Attach the wallplate. Then the wiring is
nished.
6
Flip the page over to complete setup.
Power
Source
To Light
1) Turn on the circuit breaker. Use a voltage detector
to identify the energized wire (Line wire).
2) Turn o the circuit breaker. Label the Line and Load
wires.
Take care to avoid electric shocks.
Load wireLine wire

Product Introduction Wire Your Switch
Built-in motion and ambient light sensors
work together to realize hands-free control.
Kasa smart dimmer switch turns on and
dims the lights automatically, saving you
eort and electricity bills.
Connect the wires to the smart dimmer
switch as shown below.
4
Disconnect the wires from the old switch.
Ground: Usually green or copper.
Neutral: Usually white and not connected to a dumb switch.
Line: Usually black and coming from the circuit breaker.
Load: Usually black. One end is connected to the light.
If you are unsure, consult a qualied electrician.
Turn o the circuit breaker. Then remove
the old wallplate of the wall switch and
label the Ground and Neutral wires.
1
2
Identify Line and Load wires.
3Line up the switch with the mounting
holes. Secure it with screws.
5Attach the wallplate. Then the wiring is
nished.
6
Flip the page over to complete setup.
Power
Source
To Light
1) Turn on the circuit breaker. Use a voltage detector
to identify the energized wire (Line wire).
2) Turn o the circuit breaker. Label the Line and Load
wires.
Take care to avoid electric shocks.
Load wireLine wire

Button Explanations
LED Status
Smart Wi-Fi Dimmer Switch
Quick Start Guide
7106509394 REV1.1.0 ©2022 TP-Link
Specications
Rating: 120V~ 60Hz
Load: 300W Incandescent, 150W LED
Operation temperature: 0~40℃
Method of mounting included: Independently mounted
(Vertically position only);
Operating control, Type 1 action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1
Need some help?
?
Visit www.tp-link.com/support
for technical support, user guides, FAQs,
warranty & more
Flashing amber
Flashing green
White
Solid red
Stay green for 30s
Flashing amber & green
Connecting to Wi-Fi.
Ready for setup.
Device resetting.
Light fixture is off.
Disconnected from Wi-Fi.
Connected to Wi-Fi.
*Images may dier from your actual product.
Restart
Reset
Press and hold for about 5s to reset
Wi-Fi while keeping other settings.
Press to restart your switch.
Decrease or increase the brightness.
Press and hold for about 10s to restore
your switch to factory default settings.
/
Set Up Your Switch Appearance
STEP 2 SET UP
Tap the button in the app and select Smart
Switches. Then follow the step-by-step app
instructions to set up your smart dimmer
switch.
DOWNLOAD APP
Get the Kasa Smart app from the App Store or
Google Play.
STEP 1
OR
Safety Notice
Before installing, servicing or removing the switch, read and follow all
safety precautions including the following:
• CAUTION – Risk of Electric Shock – More than one disconnect switch
may be required to de-energize the equipment before servicing. A
circuit breaker which disconnects the Line and Neutral conductor
simultaneously is suitable. Ensure power is o at the circuit breaker
before removing or installing any switch. Use a non-contact voltage
tester to ensure the power is o.
• The Smart Switch must be installed and used in accordance with the
National Electric Code (NEC) or your local electrical code. If you are
unfamiliar with these codes and requirements, or are uncomfortable
performing the installation, consult a qualied electrician.
• Do not install the Smart Switch with wet hands or when standing on wet
or damp surfaces.
• Install only in a suitable UL Listed outlet box (suitable dimensions: H >
2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).
• Tighten terminal screws to 13 lbf-in.
High Voltage-Disconnect power supply before servicing
CAUTION
On/O
Button
Dimmer
Buttons
Motion
Sensor
Restart
LED
Reset
Ambient
Light
Sensor

Button Explanations
LED Status
Smart Wi-Fi Dimmer Switch
Quick Start Guide
7106509394 REV1.1.0 ©2022 TP-Link
Specications
Rating: 120V~ 60Hz
Load: 300W Incandescent, 150W LED
Operation temperature: 0~40℃
Method of mounting included: Independently mounted
(Vertically position only);
Operating control, Type 1 action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1
Need some help?
?
Visit www.tp-link.com/support
for technical support, user guides, FAQs,
warranty & more
Flashing amber
Flashing green
White
Solid red
Stay green for 30s
Flashing amber & green
Connecting to Wi-Fi.
Ready for setup.
Device resetting.
Light fixture is off.
Disconnected from Wi-Fi.
Connected to Wi-Fi.
*Images may dier from your actual product.
Restart
Reset
Press and hold for about 5s to reset
Wi-Fi while keeping other settings.
Press to restart your switch.
Decrease or increase the brightness.
Press and hold for about 10s to restore
your switch to factory default settings.
/
Set Up Your Switch Appearance
STEP 2 SET UP
Tap the button in the app and select Smart
Switches. Then follow the step-by-step app
instructions to set up your smart dimmer
switch.
DOWNLOAD APP
Get the Kasa Smart app from the App Store or
Google Play.
STEP 1
OR
Safety Notice
Before installing, servicing or removing the switch, read and follow all
safety precautions including the following:
• CAUTION – Risk of Electric Shock – More than one disconnect switch
may be required to de-energize the equipment before servicing. A
circuit breaker which disconnects the Line and Neutral conductor
simultaneously is suitable. Ensure power is o at the circuit breaker
before removing or installing any switch. Use a non-contact voltage
tester to ensure the power is o.
• The Smart Switch must be installed and used in accordance with the
National Electric Code (NEC) or your local electrical code. If you are
unfamiliar with these codes and requirements, or are uncomfortable
performing the installation, consult a qualied electrician.
• Do not install the Smart Switch with wet hands or when standing on wet
or damp surfaces.
• Install only in a suitable UL Listed outlet box (suitable dimensions: H >
2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).
• Tighten terminal screws to 13 lbf-in.
High Voltage-Disconnect power supply before servicing
CAUTION
On/O
Button
Dimmer
Buttons
Motion
Sensor
Restart
LED
Reset
Ambient
Light
Sensor

Button Explanations
LED Status
Smart Wi-Fi Dimmer Switch
Quick Start Guide
7106509394 REV1.1.0 ©2022 TP-Link
Specications
Rating: 120V~ 60Hz
Load: 300W Incandescent, 150W LED
Operation temperature: 0~40℃
Method of mounting included: Independently mounted
(Vertically position only);
Operating control, Type 1 action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1
Need some help?
?
Visit www.tp-link.com/support
for technical support, user guides, FAQs,
warranty & more
Flashing amber
Flashing green
White
Solid red
Stay green for 30s
Flashing amber & green
Connecting to Wi-Fi.
Ready for setup.
Device resetting.
Light fixture is off.
Disconnected from Wi-Fi.
Connected to Wi-Fi.
*Images may dier from your actual product.
Restart
Reset
Press and hold for about 5s to reset
Wi-Fi while keeping other settings.
Press to restart your switch.
Decrease or increase the brightness.
Press and hold for about 10s to restore
your switch to factory default settings.
/
Set Up Your Switch Appearance
STEP 2 SET UP
Tap the button in the app and select Smart
Switches. Then follow the step-by-step app
instructions to set up your smart dimmer
switch.
DOWNLOAD APP
Get the Kasa Smart app from the App Store or
Google Play.
STEP 1
OR
Safety Notice
Before installing, servicing or removing the switch, read and follow all
safety precautions including the following:
• CAUTION – Risk of Electric Shock – More than one disconnect switch
may be required to de-energize the equipment before servicing. A
circuit breaker which disconnects the Line and Neutral conductor
simultaneously is suitable. Ensure power is o at the circuit breaker
before removing or installing any switch. Use a non-contact voltage
tester to ensure the power is o.
• The Smart Switch must be installed and used in accordance with the
National Electric Code (NEC) or your local electrical code. If you are
unfamiliar with these codes and requirements, or are uncomfortable
performing the installation, consult a qualied electrician.
• Do not install the Smart Switch with wet hands or when standing on wet
or damp surfaces.
• Install only in a suitable UL Listed outlet box (suitable dimensions: H >
2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).
• Tighten terminal screws to 13 lbf-in.
High Voltage-Disconnect power supply before servicing
CAUTION
On/O
Button
Dimmer
Buttons
Motion
Sensor
Restart
LED
Reset
Ambient
Light
Sensor