TP-Link JetStream T2600G-28TS User manual

Installation Guide
Gigabit L2 Managed Switch
T2600G-28TS (TL-SG3424)
T2600G-52TS (TL-SG3452)
Business Networking Solution

I
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of TP-LINK
TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any derivative such
as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright
© 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
Copyright & Trademarks

II Related Document
Related Document
The User Guide and CLI Reference Guide of the product are provided on the resource
CD.
To obtain the latest product information, please visit the official website:
http://www.tp-link.com
About this Installation Guide
This Installation Guide describes the hardware characteristics, installation methods and
the points that should be attended to during installation.
This Installation Guide is structured as follows:
Chapter 1 Introduction. This chapter describes the external components of the
switch.
Chapter 2 Installation. This chapter illustrates how to install the switch.
Chapter 3 Lightning Protection. This chapter illustrates how to prevent lightning
damage.
Chapter 4 Connection. This chapter illustrates how to do the physical connection of
the switch.
Chapter 5 Configuration. This chapter instructs you to configure the switch via Web
Interface and CLI commands.
Appendix A Troubleshooting.
Appendix B Hardware Specifications.

III
Audience
This Installation Guide is for:
Network Engineer
Network Administrator
Conventions
Due to the similarity in the structure of the L2 Managed Switch series, in this Installation
Guide we take T2600G-28TS as an example to illustrate Chapter 2 Installation, Chapter
3 Lightning Protection and Chapter 4 Connection.
This guide uses the specific formats to highlight special messages. The following table
lists the notice icons that are used throughout this guide.
Remind to be careful. A caution indicates a potential which may
result in device damage.
Remind to take notice. The note contains the helpful
information for a better use of the product.
Audience

IV
Contents
Contents
Chapter 1 Introduction ———————————— 01
1.1 Product Overview.........................................01
1.2 Appearance .................................................01
Chapter 2 Installation ————————————— 05
2.1 Package Contents.........................................05
2.2 Safety Precautions........................................05
2.3 Installation Tools ..........................................07
2.4 Product Installation ......................................07
Chapter 3 Lightning Protection ———————— 09
3.1 Cabling Reasonably ......................................09
3.2 Connect to Ground .......................................11
3.3 Equipotential Bonding...................................12
3.4 Use Lightning Arrester ..................................13
Chapter 4 Connection ————————————— 14
4.1 Ethernet Port ...............................................14
4.2 SFP Port ......................................................14
4.3 Console Port ................................................15
4.4 Verify Installation .........................................16
4.5 Power On ..................................................17
4.6 Initialization.................................................17
Chapter 5 Configuration———————————— 18
5.1 Configure the Switch via GUI ........................18
5.2 Configure the Switch Using CLI .....................19
Appendix A Troubleshooting—————————— 22
Appendix B Hardware Specifications —————— 24

01
Gigabit L2 Managed Switch
Introduction
Chapter 1 Introduction
1.1 Product Overview
T2600G-28TS and T2600G-52TS are Gigabit Ethernet switching products recently
developed by TP-LINK. T2600G-28TS possesses 24 RJ45 ports and 4 SFP slots, while
T2600G-52TS characterizes with 48 RJ45 ports and 4 SFP slots. The SFP slot enables
remote connection with SFP slots on other devices through SFP module and fiber.
T2600G-28TS/T2600G-52TS is compatible with all kinds of gigabit SFP modules. Here
you are recommended to choose gigabit SFP module produced by TP-LINK, which can
perfectly extend your network and enlarge the bandwidth. T2600G-28TS/T2600G-52TS
is your first choice to extend the originally large and medium-sized network.
Designed for workgroups and departments, T2600G-28TS/T2600G-52TS from TP-LINK
provides wire-speed performance and full set of L2 management features. It provides a
variety of service features and multiple powerful functions with high security.
The EIA-standardized framework and smart configuration capacity can provide flexible
solutions for a variable scale of networks. ACL, 802.1x and Dynamic ARP Inspection
provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and
video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing
the transport of business critical data. SNMP, RMON, WEB and CLI Log-in bring
abundant management policies. TP-LINK JetStream L2 Managed Switch integrates
multiple functions with excellent performance, and is friendly to manage, which can
fully meet the need of the users demanding higher networking performance.
1.2 Appearance
■Front Panel
The front panel of T2600G-28TS is shown as the following figure.
T2600-28TS
LEDs
10/100/1000 Mbps RJ45 Port
Console (RJ-45)
Console (USB)
SFP Port
Figure 1-1 Front Panel of T2600G-28TS
LEDs
LED Status Indication
PWR
On The switch is powered on.
Off The switch is powered off or power supply is abnormal.
Flashing Power supply is abnormal.
SYS Flashing The switch works properly.
On/Off The switch works improperly.

02
Gigabit L2 Managed Switch
Introduction
LED Status Indication
1000Mbps On A device is linked to the corresponding port and running at 1000Mbps.
Off A 10/100Mbps device or no device is linked to the corresponding port.
Link/Act
On A device is linked to the corresponding port and running properly.
Flashing Data is being transmitted or received.
Off No device is linked to the corresponding port.
Console (RJ-45) Port
Designed to connect with the serial port of a computer or terminal for monitoring
and configuring the switch.
Console (USB) Port
Designed to connect with the USB port of a computer for monitoring and configuring
the switch. The switch has an RJ-45 console port and a micro-USB console port
available. Console input is active on only one console port at a time. By default, the
micro-USB connector takes precedence over the RJ-45 connector.
10/100/1000Mbps RJ45 Port
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or
1000Mbps. Each 10/100/1000Mbps RJ45 port has a corresponding 1000Mbps LED
and Link/Act LED.
SFP Port
Designed to install the SFP module. T2600G-28TS features 4 individual SFP ports
and supports 1000M SFP module connection only.
The front panel of T2600G-52TS is shown as the following figure.
ConsoleConsole(USB)
Console (USB)
10/100/1000Mbps RJ45 Port
Console (RJ-45)
LEDs
SFP Port
Figure 1-2 Front Panel of T2600G-52TS
LEDs
LED Status Indication
PWR
On The switch is powered on.
Off The switch is powered off or power supply is abnormal.
Flashing Power supply is abnormal.
SYS Flashing The switch works properly.
On/Off The switch works improperly.

03
Gigabit L2 Managed Switch
Introduction
LED Status Indication
10/100/
1000Mbps
(Port 1-48)
Green
On A 1000Mbps device is linked to the corresponding port,
but no activity.
Flashing A 1000Mbps device is linked to the corresponding port
and data is being transmitted or received.
Yellow
On A 10/100Mbps device is linked to the corresponding
port, but no activity.
Flashing A 10/100Mbps device is linked to the corresponding port
and data is being transmitted or received.
Off No device is linked to the corresponding SFP port but
no activity.
Link/Act
(Port 49-52)
On
There is a device linked to the corresponding port.
Flashing
The corresponding SFP port is transmitting or receiving
data.
Off There is no device linked to the corresponding SFP port.
Console (RJ-45) Port
Designed to connect with the serial port of a computer or terminal for monitoring
and configuring the switch.
Console (USB) Port
Designed to connect with the USB port of a computer for monitoring and configuring
the switch. The switch has an RJ-45 console port and a micro-USB console port
available. Console input is active on only one console port at a time. By default, the
micro-USB connector takes precedence over the RJ-45 connector.
10/100/1000Mbps RJ45 Port
Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or
1000Mbps. Each 10/100/1000Mbps RJ45 port has a corresponding 1000Mbps LED.
SFP Port
Designed to install the SFP module. T2600G-52TS features 4 individual SFP ports
and supports 1000M SFP module connection only.
Port Feature
Model 10/100/1000Mbps RJ45 Port SFP Port Console Port
T2600G-28TS 24 4 2
T2600G-52TS 48 4 2
■Rear Panel
Due to the similarity of T2600G-28TS and T2600G-52TS in the rear panel, here
T2600G-28TS is used as an example.

04
Gigabit L2 Managed Switch
Introduction
100-240V~50/60Hz 0.5A
Grounding Terminal
Kensington Security Slot
Power Socket
Figure 1-3 Rear Panel of T2600G-28TS
Power Socket
Connect the female connector of the power cord here, and the male connector to
the AC power outlet. Please make sure the voltage of the power supply meets the
requirement of the input voltage (100-240V~ 50/60Hz).
Grounding Terminal
The switch already comes with lightning protection mechanism. You can also ground
the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.
For detailed information, please refer to Chapter 3 Lightning Protection.
Kensington Security Slot
Secure the lock (not provided) into the security slot to prevent the device from being
stolen.
Caution: Please use the provided power cord.