TP-Link TL-POE150S User manual

7106506857 REV5.0.0
Installation Guide
TL-POE150S (PoE Injector)
TL-POE10R (PoE Splitter)
PoE InjectorPower Socket Ethernet Device
(switch, router, etc.)
PoE Injector
LAN IN PWR DC 48V
PoE Injector Only The PoE Injector supplies steady power and data connectivity to a powered device such as PoE IP Camera, PoE
AP and PoE IP Phone through an Ethernet cable.
IP Camera AP IP Phone
Powered Device (PD)
Note:
Set the required voltage
of the non-PoE device
before cable connection.
12V 9V 5V
PoE Splitter
LAN OUT PWR DC OUT
PoE Splitter
Non-PoE Device
(suggested power:＜10W)
PoE/PoE+ Switch
PoE Splitter Only The PoE Splitter can be used with a PoE/PoE+ switch to deliver direct current (DC) power and data to a Non-PoE
device.
PoE Injector PoE SplitterPower Socket
Ethernet Device
(switch, router, etc.)
Note:
Set the required voltage
of the non-PoE device
before cable connection.
12V 9V 5V
PoE Injector
LAN IN PWR DC 48V LAN OUT PWR DC OUT
PoE Splitter
Non-PoE Device
(suggested power:＜10W)
PoE Injector & Splitter The PoE injector and PoE splitter can be used as a kit to supply power and transmit data to a Non-PoE
device.
Package Contents: PoE Injector or Splitter, Ethernet Cable, Installation Guide, Power Adapter (for PoE Injector) or Power Cable (for PoE Splitter)
For technical support and other information, please visit
http://www.tp-link.com/support, or simply scan the QR code
Some models featured in this guide may be unavailable in your country or region. For local sales information, visit http://www.tp-link.com.

PoE Injector: PoE Splitter:
Power LED Explanation
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
CE Mark Warning
Do not use this product near water, for example, in a wet basement or near a swimming
pool.
Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
SAFETY NOTICES
Cautions
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC STATEMENT
© 2017 TP-Link
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність
вимогам нормативних документів та вимогам, що передбачені чинними
законодавчими актами України.
On:Connected to PSE correctly
O:No PSE is connected
LAN OUT PWR DC OUT
PoE Splitter
PoE Injector
LAN IN PWR DC 48V
On: Supplying power normally
Flashing: No PD is connected/Supplying
power abnormally
O: No power supply
Specications
A: Yes. Both LAN and PoE ports comply with IEEE 802.3, IEEE 802.3u and IEEE
802.3ab standards and support 10/100/1000Mbps Auto-Negotiation.
Q1. Can the PoE Injector supply power to a PoE device which
doesn’t have a gigabit PoE port?
A1: Ensure the PD is PoE-compliant and its connecting port supports the PoE
function.
A2: Ensure the power consumption of the PD doesn’t exceed 15.4W,
otherwise the overload protection of the PoE Injector will be activated. The PoE
Injector complies with IEEE 802.3af standard and supports 15.4W to a PD,
while the quality and length of the Ethernet cable may inuence the reception
of the power supply.
Q2. What can I do if my PoE Injector doesn’t supply power to
the powered device or the supplied power is unstable?
FAQ
Q3. Must I use the PoE Injector together with the PoE Splitter?
A: No. The PoE Injector can supply power to all PDs compliant with IEEE
802.3af standard. The PoE Splitter is used with a PoE switch or the PoE Injector
to supply power to a non-PoE device.
Operationg Temperature 0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)
Storage Humidity 5% to 90% non-condensing
Operationg Humidity 10% to 90% non-condensing
Environmental and Physical Specifications
IEEE 802.3i, IEEE802.3u, IEEE 802.3ab, IEEE 802.3afStandards
PWR
UTP/STP of Cat. 5 or above (based on the standards that the
connected devices comply with)
LED
Ports
Cable Type
PoE Injector:
PoE Splitter:
General Specifications
10/100/1000Mbps Auto-Negotiation RJ45 LAN IN port
10/100/1000Mbps Auto-Negotiation RJ45 POWER+DATA
OUT port
DC 48V Power Input port
10/100/1000Mbps Auto-Negotiation RJ45 POWER+DATA IN
port
10/100/1000Mbps Auto-Negotiation RJ45 LAN OUT port
5V/9V/12V DC OUT Power Output port
Use only power supplies which are provided by manufacturer and in the original
packing of this product. If you have any questions, please don't hesitate to contact us.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and
2011/65/EU.
The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce.
Explanation of the symbols on the product label
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer
when he buys a new electrical or electronic equipment
Indoor use only