Trane Cold Generator CICD Series Installation and operating instructions

SAFETY WARNING
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing
of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and
training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or
serious injury. When working on the equipment, observe all precautions in the literature and on the tags,
stickers, and labels that are attached to the equipment.
Cold Generator™ Compact Chiller Series
Model CICD
30 to 75 Tons (60 Hz)
R-410A
Installation, Operation,
and Maintenance
CG-SVX044B-EN
June 2019

© 2019 Ingersoll Rand CG-SVX044B-EN
Introduction
Read this manual thoroughly before operating or servicing
this unit.
Warnings, Cautions, and Notices
Safety advisories appear throughout this manual as
required. Your personal safety and the proper operation of
this machine depend upon the strict observance of these
precautions.
Important Environmental Concerns
Scientific research has shown that certain man-made
chemicals can affect the earth’s naturally occurring
stratospheric ozone layer when released to the
atmosphere. In particular, several of the identified
chemicals that may affect the ozone layer are refrigerants
that contain Chlorine, Fluorine and Carbon (CFCs) and
those containing Hydrogen, Chlorine, Fluorine and
Carbon (HCFCs). Not all refrigerants containing these
compounds have the same potential impact to the
environment. Trane advocates the responsible handling of
all refrigerants-including industry replacements for CFCs
and HCFCs such as saturated or unsaturated HFCs and
HCFCs.
Important Responsible Refrigerant
Practices
Trane believes that responsible refrigerant practices are
important to the environment, our customers, and the air
conditioning industry. All technicians who handle
refrigerants must be certified according to local rules. For
the USA, the Federal Clean Air Act (Section 608) sets forth
the requirements for handling, reclaiming, recovering and
recycling of certain refrigerants and the equipment that is
used in these service procedures. In addition, some states
or municipalities may have additional requirements that
must also be adhered to for responsible management of
refrigerants. Know the applicable laws and follow them.
The three types of advisories are defined as follows:
WARNING Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTIONsIndicates a potentially hazardous
situation which, if not avoided, could
result in minor or moderate injury. It
could also be used to alert against
unsafe practices.
NOTICE Indicates a situation that could result in
equipment or property-damage only
accidents.
WARNING
Proper Field Wiring and Grounding
Required!
Failure to follow code could result in death or serious
injury. All field wiring MUST be performed by qualified
personnel. Improperly installed and grounded field
wiring poses FIRE and ELECTROCUTION hazards. To
avoid these hazards, you MUST follow requirements for
field wiring installation and grounding as described in
NEC and your local/state electrical codes.
WARNING
Personal Protective Equipment (PPE)
Required!
Failure to wear proper PPE for the job being undertaken
could result in death or serious injury. Technicians, in
order to protect themselves from potential electrical,
mechanical, and chemical hazards, MUST follow
precautions in this manual and on the tags, stickers,
and labels, as well as the instructions below:
• Before installing/servicing this unit, technicians
MUST put on all PPE required for the work being
undertaken (Examples; cut resistant gloves/sleeves,
butyl gloves, safety glasses, hard hat/bump cap, fall
protection, electrical PPE and arc flash clothing).
ALWAYS refer to appropriate Material Safety Data
Sheets (MSDS)/Safety Data Sheets (SDS) and OSHA
guidelines for proper PPE.
• When working with or around hazardous chemicals,
ALWAYS refer to the appropriate MSDS/SDS and
OSHA/GHS (Global Harmonized System of
Classification and Labelling of Chemicals) guidelines
for information on allowable personal exposure
levels, proper respiratory protection and handling
instructions.
• If there is a risk of energized electrical contact, arc, or
flash, technicians MUST put on all PPE in accordance
with OSHA, NFPA 70E, or other country-specific
requirements for arc flash protection, PRIOR to
servicing the unit. NEVER PERFORM ANY
SWITCHING, DISCONNECTING, OR VOLTAGE
TESTING WITHOUT PROPER ELECTRICAL PPE AND
ARC FLASH CLOTHING. ENSURE ELECTRICAL
METERS AND EQUIPMENT ARE PROPERLY RATED
FOR INTENDED VOLTAGE.

Introduction
CG-SVX044B-EN 3
Copyright
This document and the information in it are the property of
Trane, and may not be used or reproduced in whole or in
part without written permission. Trane reserves the right
to revise this publication at any time, and to make changes
to its content without obligation to notify any person of
such revision or change.
Trademarks
All trademarks referenced in this document are the
trademarks of their respective owners.
Factory Training
Factory training is available through Trane University™ to
help you learn more about the operation and maintenance
of your equipment. To learn about available training
opportunities contact Trane University™.
Online: www.trane.com/traneuniversity
Phone: [phone]
Email: [email protected]
Revision History
• Updated new figure in cover page.
• Model number description chapter is revised to
include model string from product catalog.
• Dimensions and weights chapter is revised to include
all the images from product catalog.
• Wiring chapter revised to include new wiring
diagrams.
WARNING
Follow EHS Policies!
Failure to follow instructions below could result in
death or serious injury.
• All Ingersoll Rand personnel must follow Ingersoll
Rand Environmental, Health and Safety (EHS)
policies when performing work such as hot work,
electrical, fall protection, lockout/tagout, refrigerant
handling, etc. All policies can be found on the BOS
site. Where local regulations are more stringent than
these policies, those regulations supersede these
policies.
• Non-Ingersoll Rand personnel should always follow
local regulations.

4CG-SVX044B-EN
Table of Contents
Model Number Descriptions . . . . . . . . . . . . . . 5
General Information . . . . . . . . . . . . . . . . . . . . . 7
Unit Description . . . . . . . . . . . . . . . . . . . . . . . 7
General Data . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Dimensions and Weights . . . . . . . . . . . . . . . . 11
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation Mechanical . . . . . . . . . . . . . . . . . . 21
General Installation Information . . . . . . . . 21
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Noise Considerations . . . . . . . . . . . . . . . . . 21
Foundation . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Access Restrictions . . . . . . . . . . . . . . . . . . . 23
Compressor Mounting . . . . . . . . . . . . . . . . 23
Direct Mounting . . . . . . . . . . . . . . . . . . . . . . 23
Unit Leveling . . . . . . . . . . . . . . . . . . . . . . . . . 23
Typical Water Piping . . . . . . . . . . . . . . . . . . 23
Avoidance of Short Water Loops . . . . . . . 23
Minimum Water Volume for a Process Appli-
cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Unit Piping . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation Electrical . . . . . . . . . . . . . . . . . . . . 30
General Recommendations . . . . . . . . . . . . 30
Equipment Grounding . . . . . . . . . . . . . . . . . 31
Unit Power Wiring . . . . . . . . . . . . . . . . . . . . 31
Control Power Supply . . . . . . . . . . . . . . . . . 32
External Contacts and Peripherals . . . . . . 32
Controls Interface . . . . . . . . . . . . . . . . . . . . . . . 33
Unit Controller — General . . . . . . . . . . . . . 33
Unit Controller
Software Installation and Setup . . . . . . . . 33
Unit Start-Up Procedures . . . . . . . . . . . . . . . . .35
Pre-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Sequence of Operation . . . . . . . . . . . . . . . . .35
Checking Operating Conditions . . . . . . . . .36
System Superheat . . . . . . . . . . . . . . . . . . . . .36
System Subcooling . . . . . . . . . . . . . . . . . . . .36
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Normal Unit Shutdown . . . . . . . . . . . . . . . . .37
Extended Shutdown Procedure . . . . . . . . .37
Unit Restart . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Periodic Maintenance . . . . . . . . . . . . . . . . . .39
Compressor Maintenance . . . . . . . . . . . . . .39
Heat Exchanger Maintenance . . . . . . . . . . .40
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Piping System Flushing Procedure . . . . . . .53
Water Treatment Requirements . . . . . . . . .53

CG-SVX044B-EN 5
Digits 1 to 4— Model
CICD= Compact Indoor Chiller
Digits 5 to 7 — Nominal Capacity
030 = 30 Nominal Tons
045 = 45 Nominal Tons
055 = 55 Nominal Tons
065 = 65 Nominal Tons
075 = 75 Nominal Tons
Digit 8 — Unit Voltage
A = 208 V/60 Hz/3 Phase
B = 230 V/60 Hz/3 Phase
F = 460 V/60 Hz/3 Phase
G = 575 V/60 Hz/3 Phase
Digits 9 — Unit Application
A = Water-Cooled Chiller
B = Compressor Chiller with Remote
Condenser (40°F to 115°F)
D = Compressor Chiller with Remote
Condenser (20°F)
Digit 10 — Refrigeration Style
A = R-410A Scroll
Digit 11 — Number of Circuits
1 = Single Circuit
2=DualCircuit
Digit 12 — Efficiency/Capacity
1 = Standard Efficiency
2 = High Capacity Evaporator (Allows
40F leaving water)
Digit 13 — Design Sequence
0 = Factory Assigned
Digit 14 — Array System
0 = Non-Array System
1 = Array System
Digit 15 — Evaporator Heat
Exchanger Type
0 = Brazed Plate
Digit 16 — Evaporator Fluid Type
0 = Water
2 = Ethylene Glycol
3 = Propylene Glycol
Digit 17 — Evaporator Flow
0 = Constant Flow Primary
1 = Variable Flow Primary
Digit 18 — Evaporator
Temperature Range
0 = Standard Cooling
40 to 65°F [5.5 to 18.3°C]
1 = Standard Cooling/Ice Making
20 to 65°F [-6.7 to 18.3°C]
2 = Low Temperature Glycol Process
(10 to 42°F) [-12.2 to 5.5°C]
Digit 19 — Evaporator Control
Valves
0 = Manual Balancing Isolating
Valves
1 = Motorized Chilled Water Isolating
Valve
Digit 20 — Condenser Heat
Exchanger Type
0 = Brazed Plate
1 = Shell and Tube
5 = Remote Condenser
Digit 21— Condenser Fluid Type
0 = Water
2 = Ethylene Glycol
3 = Propylene Glycol
9 = Not Applicable — Compressor-
Chiller
Digit 22 — Condenser Heat
Recovery
0 = No Heat Recovery
Digit 23 — Condenser Corrosion
Resistance
0=Standard
1 = Cupro-Nickel (Avail. Shell and
Tube Only)
Digit 24 — Condenser Control
Valves
1 = Manual Valve
2 = Motorized Head Pressure Control
Valve
Digit 25 — Power Feed
0 = Single Point Power (5 kA Rating)
A = Single Point Power (5 kA Rating) +
Phase and Voltage Monitor
B = Single Point Power (100 kA
Rating)
C = Single Point Power (100 kA
Rating) + Phase and Voltage
Monitor
D = Power Feed to Each Unit (5 kA
Rating)
E = Power Feed to Each Unit (5 kA
Rating) + Phase and Voltage
Monitor
F = Power Feed to Each Unit (100 kA
Rating)
G = Power Feed to Each Unit (100 kA
Rating) + Phase and Voltage
Monitor
Digit 26 — Power Connection
0 = Terminal Block
A = Non-Fused Disconnect Switch
B = Fused Disconnect Switch
C = High SCCR Fuse Block
D = Distribution Panel Connection
= Terminal Block; Module Power
Connection = Circuit Breaker
Digit 27 — Service Options
0=None
A = LED Lighted Control Cabinet
Digit 28 — Panel Ampere Rating
0=None
D = 250 Amp
E = 400 Amp
F = 600 Amp
G = 800 Amp
H = 1200 Amp
Digit 29 — Control Style
0 = Master Slave Controller with
Single Controller per Array
A = Supervisory Array Controller with
Controller per Module
B = Non-Array, Single Unit Controller
Digit 30 — Local Unit Controller
Interface
0 = Keypad with Dot Pixel Display
A = 10.1-in. Color Touchscreen
B = 15.4-in. Color Touchscreen
Digit 31 — Remote BMS
Interface (Digital Comm)
0=None
2=LonTalk
®
4 = BACnet®MS/TP
5 = BACnet®IP
6=MODBUS
®
8 = Johnson N2
Digit 32 — Blank
0=Blank
Digit 33 — Blank
0=Blank
Digit 34 — Refrigeration Options
1 = Active Freeze Protection (All
Circuits)
2 = Hot Gas Bypass (All Circuits)
Digit 35 — Refrigeration
Accessories
0 = Moisture Indicating Sight Glass
A = Moisture Indicating Sight Glass +
Compressor Isolation Valves
B = Moisture Indicating Sight Glass +
Replaceable Core Filter Driers
C = Moisture Indicating Sight Glass +
Replaceable Core Filter Driers +
Compressor Isolation Valves
D = Moisture Indicating Sight Glass +
Condenser Relief Valves
E = Moisture Indicating Sight Glass +
Condenser Relief Valves +
Compressor Isolation Valves
F = Moisture Indicating Sight Glass +
Condenser Relief Valves+
Replaceable Core Filter Driers
G = Moisture Indicating Sight Glass +
Condenser Relief Valves +
Replaceable Core Filter Driers +
Compressor Isolation Valves
Digit 36 — Water Connection
0 = Grooved Pipe Connection,
Standard Header Length
A = Grooved Pipe Connection,
Extended Header Length
D = No Header Piping (Heat
Exchangers Only)
Model Number Descriptions

Model Number Descriptions
6CG-SVX044B-EN
Digit 37 — Water Side Pressure
0 = 150 psi
A = 300 psi
Digit 38 — Water Strainer(s)
0=None
A = Chilled Water Flow Wye Strainer
B = Chilled Water Wye Strainer with
Installation Kit
C = Condenser Water Flow Wye
Strainer
D = Condenser Water Wye Strainer
with Installation Kit
E = Chilled and Condenser Water
Nominal Flow Wye Strainer
F = Chilled and Condenser Water
Wye Strainer with Installation Kit
Digit 39 — Water Accessories
0 = Chilled Water Flow Switch
A = Condenser Water Flow Switch
B = Analog Water Temperature
Gauge
C = Analog Water Pressure Gauge
D = Chilled Water Flow Switch +
Condenser Water Flow Switch
E = Chilled Water Flow Switch +
Analog Water Temperature
Gauge
F = Chilled Water Flow Switch +
Analog Water Pressure Gauge
G = Chilled Water Flow Switch +
Condenser Water Flow Switch +
Analog Water Temperature
Gauge
H = Chilled Water Flow Switch +
Condenser Water Flow Switch +
Analog Water Pressure Gauge
J = Chilled Water Flow Switch +
Analog Water Temperature
Gauge + Analog Water Pressure
Gauge
K = Chilled Water Flow Switch +
Condenser Water Flow Switch +
Analog Water Temperature
Gauge + Analog Water Pressure
Gauge
Digit 40 — Blank
0=Blank
Digit 41 — Sound Attenuator
0=None
A = Compressor Sound Blankets
B = Factory Sound Enclosure Cabinet
C = Compressor Sound Blankets +
Factory Sound Enclosure Cabinet
Digit 42 — Unit Mounting
0=None
A = Neoprene Pads
B = Leveling Kit
C = Casters/Wheels
D = Neoprene Pads and Casters/
Wheels
E = Neoprene Pads and Leveling Kit
Digit 43 — Exterior Finish and
Shipping Splits
0 = Standard Paint, Each Module
Packaged Separately
B = Custom Paint, Each Module
Packaged Separately
Digit 44 — Shipping Options
A = Framed Crate with Plastic Wrap
(Non-Shrink)
D = Fully Enclosed Crate
Digit 45 — Warranty
0 = Standard Warranty
Digit 46 — Special Options
0=None
X = With Specials

CG-SVX044B-EN 7
General Information
Unit Description
Model CICD Cold Generator™Compact Series water-
cooled chillers are designed for installation on a prepared
surface in a suitable, weatherproof location above freezing
(32°F). Each unit consists of one or two independent
refrigerant circuits, two scroll compressors, a single or
dual circuited brazed plate evaporator, a single or dual
circuited brazed plate or shell-and-tube condenser and
control box with integral control panel—all mounted on a
common frame.
Each unit is a completely assembled package that is
factory-piped, wired, leak-tested, dehydrated, charged and
run-tested for proper control operation before shipment.
Water inlet and outlet openings are covered before
shipment. CICD units are shipped with an operating
charge of refrigerant and oil.
General Data
Table 1. General data
Size 30 45 55 65 75
Compressor
Quantity 2 2 2 2 2
Nominal Tons @ 60 Hz tons 15/15 20/20 25/25 32/32 35/35
Compressor Sound Data dbA 84 89 89 92 90
Compressor Sound Data with Sound Blankets Only(a) dbA 78 85 85 88 87
Evaporator
Water Storage gal 10 11 12 13 14
Minimum Flow gpm 30 40 50 65 75
Maximum Flow gpm 150 245 245 250 264
Brazed Plate Condenser
Water Storage gal 11 11 12 13 14
Minimum Flow gpm 55 75 90 115 130
Maximum Flow gpm 150 245 245 250 250
Shell and Tube Condenser
Water Storage gal 9 9 9 10 10
Minimum Flow gpm 35 60 60 85 85
Maximum Flow gpm 150 245 245 250 250
(a)Compressor manufacturer sound power is given at rated compressor AHRI conditions measured in free space for tandem compressor sets.

General Information
8CG-SVX044B-EN
Unit Components
Figure 1. Unit components
Detachable
Water
Header Frame
Easily Accessible
Condenser for
Easy Cleaning Brazed Plate or
Shell and Tube
Condenser
Locking Door
OFF/AUTO Switch,
RUN Light, ALARM
Light
Keypad or
Touchscreen
Controller
Display
Single or Dual
Refrigeration
Circuit(s)
Manual or Motorized
Balancing/Isolation
Valves
Standard or
Replaceable Core
Filter Drier(s)

CG-SVX044B-EN 9
Pre-Installation
To protect against loss due to damage incurred in transit,
complete the following checklist upon receipt of the unit.
A more in depth list is included with the packing list
adhered to the side of the shipping crate.
• Inspect the individual pieces of the shipment before
accepting the unit. Check for obvious damage to the
unit or packing material.
• Inspect the unit for concealed damage as soon as
possible after delivery and before it is stored.
Concealed damage must be reported within 15 days.
• If concealed damage is discovered, stop unpacking the
shipment. Do not remove damaged material from the
receiving location. Take photos of the damage, if
possible. The owner must provide reasonable
evidence that the damage did not occur after delivery.
• Notify the carrier’s terminal of the damage
immediately, by phone and by mail. Request an
immediate, joint inspection of the damage with the
carrier and the consignee.
• Notify the Trane sales representative and arrange for
repair. However, do not repair the unit until damage is
inspected by the carrier’s representative.
After completing the inspection checklist, identify the unit
with the unit nameplate, packing list and ordering
information. The unit nameplate is mounted inside the
control box.
See “Model Number Descriptions,” p. 5 for additional data
that can be found on the nameplate.
Check all items against the shipping list. Verify that it is the
correct unit and that it is properly equipped. If optional
neoprene pads (or other ship-loose items) are ordered,
they are secured in place on the shipping skid or inside the
unit control box.
This Installation, Operation and Maintenance manual, the
Controls IOM, checklists and other pertinent documents
can also be found in the unit control box. Be sure to read
all of this literature before installing and operating the unit.

10 CG-SVX044B-EN
Electrical Data
Table 2. Electrical data
Compressor Wiring
Size Rated Voltage Qty
# of
Refrigerant
Circuits Nominal Tons RLA (each) LRA (each)
Minimum
Circuit
Ampacity
Max
Fuse
Size Recommended Dual Element Fuse Size
30
200-230/60/3
2 1 or 2 15/15
48 351 109 150 110
460/60/3 25 197 56 80 60
575/60/3 22 135 51 70 60
45
200-230/60/3
2 1 or 2 20/20
67 485 153 200 200
460/60/3 33 215 74 100 80
575/60/3 26 175 60 80 60
55
200-230/60/3
2 1 or 2 25/25
82 560 186 250 200
460/60/3 40 260 90 125 90
575/60/3 29 210 65 90 70
65
200-230/60/3
2 1 or 2 32/32
109 717 246 350 250
460/60/3 51 320 115 150 125
575/60/3 38 235 87 125 90
75
200-230/60/3
2 1 or 2 35/35
103 635 233 300 250
460/60/3 51 316 116 150 125
575/60/3 41 258 93 125 110
Notes:
1. Use copper conductors only.
2. Local codes may take precedence.
3. Voltage Utilization Range: ± 10% of rated voltage. Rated voltage (use range): 200-230/60/3 (180-253), 460/60/3 (414-506), 575/60/3 (517-632).

CG-SVX044B-EN 11
Dimensions and Weights
Dimensions
Figure 2. CICD unit dimensions, brazed plate condenser

Dimensions and Weights
12 CG-SVX044B-EN
Figure 3. CICD unit array dimensions, brazed plate condenser

Dimensions and Weights
CG-SVX044B-EN 13
Figure 4. CICD unit dimensions, shell and tube condenser
31 1/2"
16 3/4"
76"
Evap Out
27 1/4"
6" Cond In
Evap In
38"
Cond
Out
56 3/4"
60 5/8"
60"
Customer connections
6" S/40 pipe
1 3/8" 45" 8 3/4"
7/8"
Footprint
59 7/8"
29 3/4"
3/4" 6 x
PANEL
2x 29 3/4"
31 1/2"
POWER
CONTROL
WIRE ENTRY
SHELL and TUBE
CONDENSER
BRAZED PLATE
EVAPORATOR

Dimensions and Weights
14 CG-SVX044B-EN
Figure 5. CICD unit array dimensions, shell and tube condenser

Dimensions and Weights
CG-SVX044B-EN 15
Figure 6. CICD unit dimensions, remote condenser
31 1/2"
FRAME
32"
HEADER
16 3/4"
76"
Evap Out
27 1/4"
Evap In
56 3/4"
PANEL
60"
CONTROL
Customer
connections
6" S/40 pipe
POWER
WIRE ENTRY
BRAZED PLATE
EVAPORATOR
1 3/8" 45" 8 3/4"
29 3/4"
7/8"
4 3/4"
Footprint
6 x
3/4"
59 7/8"
7/8"
31 1/2"

Dimensions and Weights
16 CG-SVX044B-EN
Figure 7. CICD unit array dimensions, remote condenser

Dimensions and Weights
CG-SVX044B-EN 17
Clearances
Notes:
•Clearance of 42 inch is required in front of chiller to
other electrically grounded parts.
•Two units facing each other or other live parts require
a clearance of 48 inch.
•36 inch clearance is recommended above the chiller.
•See Figure 9 and Figure 10, p. 18 for recommended
clearance requirements for array installations.
Figure 8. Clearance — CICD single chiller application (all condenser options)

5HFRPPHQGHG
0LQ

5HFRPPHQGHG
0LQ

5HFRPPHQGHG


Dimensions and Weights
18 CG-SVX044B-EN
Figure 9. Clearance — CICD array chiller application (all condenser options)
24"
Recommended
3/4" Min.
36"
Recommended
42"
3/4" Min.
36"
Recommended
Figure 10. Clearance needed to remove chiller from array—
CICD array chiller application (all condenser options)
24"
Recommended
3/4" Min.
36"
Recommended
3/4" Min.
36"
Recommended
53"

Dimensions and Weights
CG-SVX044B-EN 19
Figure 11. Single point power distribution panel dimensions

:

7<3


+
8VHFKDUWEHORZWR
GHWHUPLQHSDQHOVL]H
$UUD\6LQJOH3RLQW3RZHU
3RZHU
'LVWULEXWLRQ
3DQHO6L]HV
&KLOOHU
0RGXOH
LQ$UUD\
&KLOOHU
0RGXOH
LQ$UUD\
1RWH
&RQWDFW\RXUORFDO7UDQHUHSUHVHQWDWLYHLIDUUD\WRWDODPSVH[FHHGVDPSV

Dimensions and Weights
20 CG-SVX044B-EN
Weights
Table 3. CICD unit weights
Shipping Weight Operating Weight
Brazed Plate
Condenser Shell-and-Tube Condenser Remote Condenser Brazed Plate Condenser Shell-and-Tube Condenser Remote Condenser
Size lbs kg lbs kg lbs kg lbs kg lbs kg lbs kg
30 1495 678 1760 798 1205 547 1720 780 2025 919 1320 599
45 1775 805 1970 894 1420 644 2040 925 2265 1027 1550 703
55 1795 814 1970 894 1410 639 2065 937 2265 1027 1545 701
65 2230 1012 2640 1197 1770 803 2565 1163 3035 1377 1940 880
75 2235 1014 2640 1197 1775 805 2570 1166 3035 1377 1945 882