Trane SmartGen HSC940 User manual

Note: “Graphics in this document are for representation only.
Actual model may differ in appearance.”
March 2017 032-5094-1A-EN
Owner’s Manual
SmartGen® HSC940
Controller

Table Of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Performance & Characteristics . . . . . . . . . . . . . . . . . . . 4
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Key Operations / Indicator Lights . . . . . . . . . . . . . 6
Auto Start / Stop Operation . . . . . . . . . . . . . . 7
Manual Start / Stop Operation . . . . . . . . . . . . . . . 8
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Shutdown Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Scope & Denition of Congurable Parameters . . . . . . . . . . . . . 14
Contents & Scope of Parameters . . . . . . . . . . . . . . . . . . 14
Enable Denitions of Programmable Output Ports . . . . . . 19
Dened Contents of Congurable Input Ports . . . . . . . . . . 21
Conditions of Crank Disconnect Selection . . . . . . . . . . . 22
Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Typical Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Connection Between Controller and Genset . . . . . . . . . 25
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Fixing Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Overall Dimension and Panel Cutout . . . . . . . . . . 27
GSM Short Message Alarm and Remote Control . . . . . . . . . . 28
GSM Short Message Alarm . . . . . . . . . . . . . . . 29
GSM Short Message Remote Control . . . . . . . . . . . . 29
Fault Finding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2032-5094-1A-EN

Overview
HSC940 genset controllers integrate digitization, intellectualization
and network technology which are used for gas genset automation and
monitor control system of single unit to achieve automatic start/stop,
data measure, alarm protection, three remote: remote control, remote
measuring and remote communication (SG485 module must be tted)
and speed regulation. The controller adopts large liquid crystal display
(LCD) and selectable Chinese, English, Spanish and Russian interface with
easy and reliable operation.
HSC940 genset controllers adopt microprocessor technology with
precision parameters measuring, xed value adjustment, time setting and
set adjusting etc. All parameters can be congured from front panel, or
by congurable port (USB to LINK, SG72 must be tted) to adjust via
PC. It can be widely used in all types of automatic genset control system
with compact structure, advanced circuits, simple connections and high
reliability.
3
032-5094-1A-EN

Performance & Characteristics
HSC940, used for single automation systems; it regulates the speed simply by adjust the throttle opening via
the driving stepper motor; auto start/stop of the unit are performed with the help of remote signal.
Key characteristics
• 132×64 LCD with backlight, multilingual interface (including Chinese, English, Spanish and
Russian), pushbutton operation;
• Suitable for 3-phase 4-wire, 3-phase 3-wire, single phase 2-wire, and 2-phase 3-wire systems
with voltage 120/240V and frequency 50/60Hz;
• Collects and shows 3-phase voltage, current, power parameter and frequency of generator.
Generator
Line voltage (Uab, Ubc, and Uca)
Phase voltage (Ua, Ub, and Uc)
Frequency Hz
• For generator, controller has over and under voltage, over and under frequency functions;
• Speed regulation function (via Driving Stepper Motor);
• Precision measure and display parameters about Engine,
Speed (SPD) r/min (unit)
Battery Voltage (VB) V (unit)
Charger Voltage (VD) V (unit)
Hour count (HC) can accumulate to max. 999999 hours.
Start times can accumulate to max. 999999 times.
• Protection: automatic start/stop of the genset, ATS(Auto Transfer Switch) control with perfect
failure indication and protection function;
• ETS (Energize to Stop), idle control, preheat control and raise speed/drop speed control; in
addition, they are all relay output.
• Parameter setting: parameters can be modied and cannot be lost even in case of power
outage; all parameters can be congured from front panel, or by congurable port (SG72 must
be tted) to adjust via PC.
• Multiple crank disconnect conditions (speed sensor, generator frequency) are optional;
• Widely power supply range DC(8~35)V, suitable to different start battery voltage environment;
• All parameters used digital adjustment, instead of conventional analog modulation with normal
potentiometer, more reliability and stability;
• Modular design, self-extinguishing ABS plastic enclosure, pluggable connection terminals and
embedded installation way; compact structure with easy mounting.
4032-5094-1A-EN

Specications
Items Contents
Operating Voltage DC8.0V to DC35.0V, Continuous Power Supply.
Power Consumption Standby: ≤2W
Working: <8W (When driving stepper motor is regulating)
Alternator Input Range
3-Phase 4-Wire
2-Phase 3-Wire
Single-Phase 2-Wire
3-Phase 3-Wire
AC15V - AC360V (ph-N)
AC15V - AC360V (ph-N)
AC15V - AC360V (ph-N)
AC30V - AC620V (ph-ph)
Alternator Frequency 50Hz/60Hz
Speed Sensor Voltage 1.0V to 24.0V (RMS)
Speed Sensor Frequency 10,000 Hz (max.)
Start Relay Output 5A DC28V supply output
Fuel Relay Output 5A DC28V supply output
Auxiliary Relay Output (1) 5A DC28V supply output
Auxiliary Relay Output (2) 5A DC28V supply output
Auxiliary Relay Output (3) 5A DC28V supply output
Auxiliary Relay Output (4) 5A DC28V supply output
Steady-state Speed Governing Rate <1.5%
Steady-state Speed Fluctuation Rate <0.5%
Transient Speed Governing Rate Sudden Load-on <+10%
Sudden Load-off >-15%
Recovery Time <5s
Driving Stepper Motor Mixed 2-phase; Drive current ≤1A
Case Dimension 130mm x 112mm x 39mm
Panel Cutout 110mm x 90mm
Working Conditions Temperature: (-25~+70)°C; Humidity: (20~93)%RH
Storage Condition Temperature:(-25~+70)°C
Protection Level IP55 Gasket
Insulating Intensity Apply AC2.2kV voltage between high voltage terminal and low
voltage terminal; The leakage current is not more than 3mA
within 1min.
Net Weight 0.26kg
5
032-5094-1A-EN

Operation
4.1 KEY OPERATIONS
Stop/ Reset
Stop running generator in Auto/Manual mode; Lamp test (press
at least 3 seconds); Reset alarm if alarm occurs; During stopping
process, press this button again to stop generator immediately.
Start Start genset in Manual/Test mode.
Manual Mode Pressing this key will set the module into Manual mode. Press-
ing and (or ) simultaneously can adjust LCD contrast.
Auto Mode Pressing this key will set the module into AUTO mode.
Set/Conrm Pressing this key will view set menu; In parameter setting inter-
face, press this key will shift cursor or conrm setting value.
Up/Increase Scrolls the screen up; Shift the cursor up or increase the set
value in parameter setting menu.
Down/Decrease Scrolls the screen down; Shift the cursor down or decrease the
set value in parameter setting menu.
4.2 INDICATOR LIGHTS
Alarm
Gens Normal
Indicator
Stop Indicator Close Gens
Stop
Manual Manual Auto Auto Start Set
Indicator Indicator
6032-5094-1A-EN

Operation
4.3 AUTO START/STOP OPERATION
Auto mode is selected by pressing the button; a LED besides the button will illuminate to conrm the
operation.
Automatic Start Sequence:
1. When “Remote Start” is active, “Start Delay” timer is initiated;
2. “Start Delay” countdown will be displayed on LCD;
3. When start delay is over, preheat relay energizes (if congured), “preheat delay XX s”
information will be displayed on LCD;
4. After the above delay, the Fuel Relay is energized, and then one second later, the throttle of
the driving stepper motor will rotate as the pre-set angle and then the Start Relay is engaged.
The engine is cranked for a pre-set time. If the engine fails to re during this cranking attempt
then the fuel relay and start relay are disengaged for the pre-set rest period; “crank rest time”
begins and wait for the next crank attempt.
5. Should this start sequence continue beyond the set number of attempts, the start sequence
will be terminated, the fourth line of LCD display will be highlighted with black and Fail to Start
fault will be displayed.
6. In case of successful crank attempt, the “Safety On” timer is activated and the throttle of
the driving stepper motor will govern the speed, allowing Low Oil Pressure, High Temperature,
Under speed, Charge Alternator Failure and auxiliary inputs (be congured) to stabilise without
triggering the fault. As soon as this delay is over, “start idle” delay is initiated (if congured).
7. During “start idle” delay, under speed, under frequency, under voltage alarms are inhibited.
When this delay is over, “warming up” delay is initiated (if congured).
8. After the “warming up” delay, if generator status is normal, its indicator will be illuminated.
If generator voltage and frequency have reached on-load requirements, then the generator
close relay will be energized; genset will take load; generator power indicator will illuminate
and generator will enter into Normal Running status. If voltage or frequency is abnormal, the
controller will initiate shutdown alarm (alarm information will be displayed on LCD).
Automatic Stop Sequence:
1. When the “Remote Start” signal is removed, the Stop Delay is initiated.
2. Once this “stop delay” has expired, the Generator Breaker will open and the “Cooling Delay” is
then initiated. Moreover, the generator indicator is extinguished.
3. During “Stop Idle” Delay (if congured), idle relay is energized.
4. “ETS Solenoid Hold” delay begins, ETS relay is energized while fuel relay is de-energized.
5. "Fail to Stop Delay" begins, complete stop is detected automatically.
6. When generator is stop completely, generator is placed into its standby mode. Otherwise, fail
to stop alarm is initiated and the corresponding alarm information is displayed on LCD.
7
032-5094-1A-EN

Operation
4.4 MANUAL START/STOP OPERATION
1. MANUAL START: Manual mode is selected by pressing the button; a LED besides the
button will illuminate to conrm the operation.
Then press button to start the genset; can detect crank disconnect condition and
generator accelerates to high-speed running automatically.
With high temperature, low oil pressure, over speed and abnormal voltage during generator
running, controller can protect genset to stop quickly. (please refer to No.3~8 of Automatic
Start Sequence for detail procedures.) The controller will send Close Gen signal after the
genset is normal running.
2. MANUAL STOP: Press can stop the running generators. (please refer to No.2~6 of
Automatic Stop Sequence for detail procedures).
8032-5094-1A-EN

Protection
5.1 WARNINGS
Warnings are not shutdown alarms and do not affect the operation of the genset. Warning alarms does not
lead to shutdown and the alarm information will be displayed on the LCD. Warning alarms types are as follows:
No. Type Description
1High Temperature Warn
When the controller detects that there is High Temperature input and
the shutdown is prohibited, it will initiate a warning alarm and the alarm
information will be displayed on the LCD.
2Low Oil Pressure
When the controller detects that there is Low Oil Pressure input and the
shutdown is prohibited, it will initiate a warning alarm and the alarm
information will be displayed on the LCD.
3 Fail to Stop
After the ETS delay/Fail to Stop delay has expired, if the genset stop
failure, it will initiate a warning alarm and the alarm information will be
displayed on the LCD.
4Charge Alt Fail
When the controller detects that the charger voltage has fallen below the
pre-set value, it will initiate a warning alarm and the alarm information
will be displayed on the LCD.
5Battery Under Voltage
When the controller detects that the battery voltage has fallen below the
pre-set value, it will initiate a warning alarm and the alarm information
will be displayed on the LCD.
6 Battery Over Voltage
When the controller detects that the battery voltage has exceeded the
pre-set value, it will initiate a warning alarm and the alarm information
will be displayed on the LCD.
7Digital Input When the digit input port is set as warning and active, it will initiate a
warning alarm and the alarm information will be displayed on the LCD.
8 Loss of Speed Signal
When the controller detects the speed is 0 and the Loss of Speed Signal
delay is set as 0, it will initiate a warning alarm and the alarm information
will be displayed on the LCD.
9 Low Coolant Level
When the controller detects that there is Low Coolant Level input, it will
initiate a warning alarm and the alarm information will be displayed on
the LCD.
10 Low Fuel Level
When the controller detects that there is Low Fuel Level input, it will
initiate a warning alarm and the alarm information will be displayed on
the LCD.
9
032-5094-1A-EN

Protection
5.2 SHUTDOWN ALARM
When controller detects shutdown alarm, it will send signal to open breaker and shuts down generator.
Besides, the alarm information will be displayed on the LCD.
Shutdown alarms as following:
No. Type Description
1 Emergency Stop
When the controller detects that there is Emergency Stop input, it will ini-
tiate a shutdown alarm and the alarm information will be displayed on the
LCD.
2High Temperature
When the controller detects that there is High Temperature input and the
shutdown is allowed, it will initiate a shutdown alarm and the alarm infor-
mation will be displayed on the LCD.
3 Low Oil Pressure
When the controller detects that there is Low Oil Pressure input and the
shutdown is allowed, it will initiate a shutdown alarm and the alarm infor-
mation will be displayed on the LCD.
4 Over Speed
When the controller detects that the generator speed has exceeded the pre-
set value, it will initiate a shutdown alarm and the alarm information will be
displayed on the LCD.
5Under Speed
When the controller detects that the generator speed has fallen below the
pre-set value, it will initiate a shutdown alarm and the alarm information
will be displayed on the LCD.
6Loss of Speed Signal
When the controller detects the speed is 0 and the Loss of Speed Signal
delay is NOT set as 0, it will initiate a shutdown alarm and the alarm infor-
mation will be displayed on the LCD.
7 Gen Over Volt.
When the controller detects that the generator voltage has exceeded the
pre-set value, it will initiate a shutdown alarm and the alarm information
will be displayed on the LCD.
8Gen Under Volt.
When the controller detects that the generator voltage has fallen below the
pre-set value, it will initiate a shutdown alarm and the alarm information
will be displayed on the LCD.
9Fail To Start
If the engine does not re after the pre-set number of attempts, it will
initiate a shutdown alarm and the alarm information will be displayed on the
LCD.
10 Gen Over Freq.
When the controller detects that the generator frequency has exceeded the
pre-set value, it will initiate a shutdown alarm and the alarm information
will be displayed on the LCD.
11 Gen Under Freq.
When the controller detects that the generator frequency has fallen below
the pre-set value, it will initiate a shutdown alarm and the alarm informa-
tion will be displayed on the LCD.
10 032-5094-1A-EN

Protection
5.2 SHUTDOWN ALARM continued
When controller detects shutdown alarm, it will send signal to open breaker and shuts down generator.
Besides, the alarm information will be displayed on the LCD.
Shutdown alarms as following:
No. Type Description
12 No gens freq When the controller detects the generator frequency is 0, it will initiate a
shutdown alarm and the alarm information will be displayed on the LCD.
13 Low Fuel Level When the controller detects that the fuel level is lower than the set value or
there is Low Fuel Level input, it will initiate a shutdown alarm and the alarm
information will be displayed on the LCD.
14 Low Coolant Level When the controller detects that there is Low Coolant Level input, it will
initiate a shutdown alarm and the alarm information will be displayed on the
LCD.
11
032-5094-1A-EN

Wiring Connections
HSC940 controller’s rear as following:
Description of terminal connection:
No. Function Cable Size Remarks
1B- 2.5mm2Connected with negative of starter battery
2 B+ 2.5mm2Connected with positive of starter battery. Max. 20A fuse is
recommended.
3 EM. Stop 1.5mm2Connected with B+ via emergency stop button
4 Fuel 1.0mm2Fuel relay output; B+ is supplied by 3 terminal; rated 5A
5 Crank 1.0mm2Start relay output; B+ is supplied by 3 terminal; rated 5A;
Connected to starter coil.
6Aux. Output 1 1.0mm2B+ is supplied by 2 terminal; rated 5A
7 Aux. Output 2 1.0mm2B+ is supplied by 2 terminal; rated 5A;
8 Aux. Output 3 1.0mm2B+ is supplied by 2 terminal; rated 5A;
9 Aux. Output 4 1.0mm2B+ is supplied by 2 terminal; rated 5A;
12 032-5094-1A-EN

Wiring Connections
Continued:
No. Function Cable Size Remarks
10 Aux. Input 1 1.0mm2Ground connected is active (B-)
Details see
form 3
11 Aux. Input 2 1.0mm2Ground connected is active (B-)
12 Aux. Input 3 1.0mm2Ground connected is active (B-)
13 Aux. Input 4 1.0mm2Ground connected is active (B-)
14 Aux. Input 5 1.0mm2Ground connected is active (B-)
15 GND The common port of sensor; (B-) has already connected.
16 CHARGER(D+) 1.0mm2Connected with charger starter’s D+ (WL) terminals. Being
hang up If there is no this terminal.
17 MP2 1.0mm2(B-) has already connected. Connected with Speed sensor,
shielding line is recommended.
18 MP1 1.0mm2Connected with Speed sensor, shielding line is recommend-
ed.
19 S11 1.0mm2
Connect to stepper motor. S11 and S12 are belong to one
phase to the motor while S21 and S22 are belong to the
other phase.
20 S12 1.0mm2
21 S21 1.0mm2
22 S22 1.0mm2
23 RS232 RX 0.5mm
Connected to GSM module.24 RS232 TX 0.5mm
25 RS232 GND 0.5mm
26 Gens AC Voltage (U) 1.0mm2Connected to U-phase of generator (2A fuse is recommend-
ed).
27 Gens AC Voltage (V) 1.0mm2Connected to V-phase of generator (2A fuse is recommend-
ed).
28 Gens AC Voltage (W) 1.0mm2Connected to W-phase of generator (2A fuse is recommend-
ed).
29 Gens AC Voltage (N) 1.0mm2Connected to N-phase of generator (2A fuse is recommend-
ed).
NOTE: LINK interface is parameters congured interface that can be programmed by
PC using an SG72 adapter. If there is need to remote control the genset, please use the
SG485 module produced by our company.
13
032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.1 CONTENTS AND SCOPES OF PARAMETERS
Form 1
No Items Range Default Description
1 Start Delay (0-3600)s 1Time from remote start signal is active to start gen-
set.
2Stop Delay (0-3600)s 1Time from remote start signal is deactivated to gen-
set stop.
3Start Attempts (1-10)times 3Maximum crank times of crank attempts. When reach
this number, controller will send start failure signal.
4 Preheat Delay (0-300)s 0Power-on time of heater plug before starter is pow-
ered up.
5Choke Time (0-300)s 0Power-on time of choke after crank succeeds.
6Cranking Time (3-60)s 8Power-on time of starter
7Crank Rest Time (3-60)s 10 The waiting time before second power up when en-
gine start fail.
8 Safety On Delay (1-60)s 10
Alarms for low oil pressure, high temperature, under
speed, under frequency/voltage, charge alt failure
are inactive.
9Start Idle Time (0-3600)s 0 Idle running time of genset when starting.
10 Warming Up Time (0-3600)s 10 Warming time between genset switch on and high
speed running.
11 Cooling Time (3-3600)s 10 Radiating time before genset stop, after it unloads.
12 Stop Idle (0-3600)s 0 Idle running time when genset stop.
13 ETS Solenoid Hold (0-120)s 20 Stop electromagnet’s power on time when genset is
stopping.
14 Fail to Stop Delay (0-120)s 0
Time between ending of genset idle delay and
stopped when “ETS time” is set as 0; Time between
ending of ETS hold delay and stopped when “ETS
time” is not 0.
15 Close Time (0-10)s 5.0 Pulse width of generator switch on. When it is 0,
means output constantly.
14 032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.1 CONTENTS AND SCOPES OF PARAMETERS continued
Form 1 continued
No Items Range Default Description
16 Flywheel Teeth (1-300) 118
Tooth number of the engine, for judging of starter
crank disconnect conditions and inspecting of engine
speed. See the installation instructions.
17 Gen Abnormal Delay (0-20.0)s 10.0 The alarm delay of generator over voltage and under
voltage.
18 Gen Over Voltage
(Shutdown) (30-620)V 264
When generator voltage has exceed the set value
and the “Gen abnormal delay” has expired, Gen Over
Voltage shutdown alarm is active. When set the value
as 620V, the controller does not detect over voltage
signal.
19
Generator Under
Voltage
(Shutdown)
(30-620)V 88
When generator voltage has fallen below the set
value and the “Gen abnormal delay” has expired,
Gen Under Voltage shutdown alarm is active. When
set the value as 30V, the controller does not detect
under voltage signal.
20 Under Speed (Shut-
down)
(0-6000)
r/min 1000
When engine speed has fallen below the set value
for 10s, Under Speed shutdown alarm is active. It will
initiate a shutdown alarm signal.
21 Over Speed (Shut-
down)
(0-6000)
r/min 4200
When engine speed has exceed the set value for 2s,
Over Speed shutdown alarm is active. It will initiate a
shutdown alarm signal.
22 Under Frequency
(Shutdown) (0-75.0)Hz 45.0
When generator frequency has fallen below the set
value but Not equal to 0 for 10s, Under Frequency
shutdown alarm is active. It will initiate a shutdown
alarm signal.
23 Over Frequency
(Shutdown) (0-75.0)Hz 68.0
When generator frequency has exceeded the set val-
ue for 2s, Over Frequency shutdown alarm is active. It
will initiate a shutdown alarm signal.
24 Loss of Speed Signal (0-20.0)s 5.0 If the set value is 0, only warning and not to shut-
down the generator.
15
032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.1 CONTENTS AND SCOPES OF PARAMETERS continued
Form 1 continued
No Items Range Default Description
25 Charge Alt Failure
(Warning) (0-30)V 6.0
During generator is normal running, when alternator
D+(WL) voltage has fallen below the set value and
remains for 5s, It will initiate a shutdown alarm signal.
26 Battery Over
Voltage (Warning) (12-40)V 33.0
When battery voltage has exceeded the set value and
remains for 20s, It will initiate a warning alarm signal.
Only warning and not to shutdown the generator.
27 Battery Under Volt-
age (Warning) (4-30)V 8.0
When battery voltage has fallen below the set value
and remains for 20s, It will initiate a warning alarm
signal. Only warning and not to shutdown the gener-
ator.
28 Auxiliary Output 1 (0-17) 15 Factory default: Choke Control
29 Auxiliary Output 2 (0-17) 2 Factory default: Energized To Stop
30 Auxiliary Output 3 (0-17) 3 Factory default: Idle Control
31 Auxiliary Output 4 (0-17) 5 Factory default: Close Generator
32 Auxiliary Input 1 (0-15) 1 Factory default: High Temperature Input
33 Auxiliary Input 1
Active (0-1) 0 Factory default: Close to active
34 Auxiliary Input 1
Delay (0-20.0)s 2.0
35 Auxiliary Input 2 (0-15) 2 Factory default: Low Oil Pressure Input
36 Auxiliary Input 2
Active (0-1) 0 Factory default: Close to active
37 Auxiliary Input 2
Delay (0-20.0)s 2.0
38 Auxiliary Input 3 (0-15) 10 Factory default: Remote Start
39 Auxiliary Input 3
Active (0-1) 0 Factory default: Close to active
40 Auxiliary Input 3
Delay (0-20.0)s 2.0
41 Auxiliary Input 4 (0-15) 11 Factory default: Fuel Level Warn
16 032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.1 CONTENTS AND SCOPES OF PARAMETERS continued
Form 1 continued
No Items Range Default Description
42 Auxiliary Input 4
Active (0-1) 0 Factory default: Close to active
43 Auxiliary Input 4
Delay (0-20.0)s 2.0
44 Auxiliary Input 5 (0-15) 3 Factory default: Warn Input
45 Auxiliary Input 5
Active (0-1) 0 Factory default: Close to active
46 Auxiliary Input 5
Delay (0-20.0)s 2.0
47 Power On Mode (0-2) 0
0: Stop Mode
1: Manual Mode
2: Auto Mode
48 Module Address (1-254) 1 Communication address of controller.
49 Passwords (0-9999) 1234
50 Crank Disconnect (0-2) 2
There are 2 conditions of disconnecting starter with
engine: Generator Frequency and Speed Sensor. Each
condition can be used alone and simultaneously to
separating the start motor and genset as soon as
possible. See Table 4.
51 Disconnect Engine
Speed
(0-3000)
r/min 360 When the engine speed has exceeded the set value, starter will be disconnected.
52 Disconnect Genera-
tor Freq (10.0-30.0)Hz 14.0 When the generator frequency has exceeded the set value, starter will be disconnected.
53 High Temp. Inhibit (0-1) 0Factory default: High Temp. Shutdown. When high
temperature occurs, shutdown alarm is active. Note 1
54 Low OP Inhibit (0-1) 0Factory default: when low oil pressure occurs, shut-
down alarm is active. Note 2
55 Voltage Input (0-3) 00: 3P4W; 1: 2P3W
2: 1P2W; 3: 3P3W Note 3
56 Rated Speed (0-6000)
r/min 1500 Offer standard to adjust rated speed.
17
032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.1 CONTENTS AND SCOPES OF PARAMETERS continued
Form 1 continued
No Items Range Default Description
57 Idle Speed (0-6000) r/
min 900 Offer standard to adjust idle speed.
58 Idle Slope 0-6000 10
The rising speed rate during the process of genset
change idle running status into rated speed running
status.
59 Idle Gain 1-1000 150 The gain is regulated during the genset is idle run-
ning.
60 Crank Angle (0-90)° 45 The throttle opening before the genset is starting.
61 Crank Disc. Angle (0-90)° 35 The initial opening of the throttle after the genset is
started.
62 Proportional Gain 1-3000 1100
The regulated gain when the genset is running in
rated speed.
63 Integral Gain 1-3000 20
64 Differential Gain 1-3000 1
65 Total Gain 1-1000 100
66 Window (1-1000)
r/min 1
67 Window Gain 1000-3000 1950
68 Position Gain 0-1000 0
69 Compensate Gain 0-100 0
70 Scheduled Enable (0-1) 0Factory default: Disable
71 Scheduled Run Mode (0-1) 0 Factory default: Off Load
72 Schedule Period (0-2) 0 Factory default: 0 Monthly
73 Schedule Day (1-31) 1
74 Schedule Week (0-6) 0 Factory default: 0 Daily
75 Schedule Hour (0-23) 0
76 Schedule Minute (0-59) 0
77 Schedule Duration (0-9999) 0
78 GSM Set (0-1) 0Factory default: Disable
18 032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.1 CONTENTS AND SCOPES OF PARAMETERS continued
Note 1. If “high temperature inhibit” is congured, or set auxiliary input as “inhibit high
temperature stop” and this input is active, when temperature is higher than the preset
value, or high temperature alarm input is active, controller will send warning signal only
and not stop the unit.
Note 2. If “low oil pressure inhibit” is congured, or set auxiliary input as “inhibit low oil
pressure stop” and this input is active, when oil pressure is lower than the preset value,
or low oil pressure alarm input is active, controller will send warning signal only and not
stop the unit.
Note 3. If “3P3W” is selected, maximum shutdown threshold of “Gens Over Voltage” can
be set as 620V; when select others, maximum shutdown threshold can be set as 360V.
7.2 ENABLE DEFINITION OF PROGRAMMABLE OUTPUT PORTS
Form 2
No Items Description
0Not Used Output port is deactivated when “Not Used” is selected.
1Common Alarm
Include all shutdown alarms and warning alarms. When there is warning
alarm only, it is not self-lock; when a shutdown alarm occurs, it is self-lock
until the alarm is reset.
2Energized to Stop Suitable for genset with electromagnet and will active after “stop idle
delay”. It is deactivated when the “ETS Solenoid delay” expires.
3 Idle Control
Used for engine which has idles. Close before starting and open in warm-
ing up delay; Close during stop idle delay and open when stop is complet-
ed.
4 Preheat Control Close before starting and open before power up;
5 Close Generator When close time is 0, it’s continuous output.
6Reserved
7Open ATS When close time is 0, it’s disabled.
8 Raise Speed Close when the generator enters into Warming Up delay (close time:
warming up delay) while open when Aux. Raise Speed input is active.
19
032-5094-1A-EN

Scope & Denitions of Congurable Parameters
7.2 ENABLE DEFINITION OF PROGRAMMABLE OUTPUT PORTS continued
Form 2 continued
No Items Description
9 Drop Speed
Close when the generator enters into Stop Idle delay/ Energized to Stop
delay (close time: Stop Idle delay) while open when Aux. Drop Speed input
is active.
10 Generator Run Action when genset is normal running while deactivated when engine
speed is lower than the “crank disconnect speed”.
11 Fuel Pump Control
Close when fuel level is lower than the “Fuel Pump On” value or when low
fuel level warning input is active; Open when fuel level is higher than the
“Fuel Pump Off” and low fuel level warning input is deactivated;
12 High Speed Control Close when the generator enters into Warming Up delay while open after
cooling delay.
13 In Auto Mode The controller is in automatic mode.
14 Fuel Relay Output To control fuel relay output.
15 Choke Control Start to output in cranking period; in addition, during safety on running,
output for preset delay.
16 Reserved
17 Reserved
20 032-5094-1A-EN