Transition Networks SSDTF1011-105 User manual

Installation . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . .9
Cable Specifications . . . . . . . . . .10
Technical Specifications . . . . . . .12
Troubleshooting . . . . . . . . . . . . .13
Compliance Information . . . . . . .16
* Typical maximum cable distance. (Actual
distance is dependent upon the physical
characteristics of the network.)
Note: The SSDTF10xx-10x requires a CSU
between the converter and the Public
Telephone Network.
SSDTF1027-105 RJ-45
1.5 km (5,000 feet)*
ST, 1300 nm multimode
5 km (3.1 miles)*
Part Number Port One - Copper Port Two - Duplex Fiber-Optic
SSDTF1011-105 RJ-45
1.5 km (5,000 feet)*
ST, 850 nm multimode
2 km (1.2 miles)*
SSDTF1012-105 RJ-45
1.5 km (5,000 feet)*
ST, 1310 nm single mode
8 km (4.8 miles)*
SSDTF1013-105 RJ-45
1.5 km (5,000 feet)*
SC, 850 nm multimode
2 km (1.2 miles)*
SSDTF1014-105 RJ-45
1.5 km (5,000 feet)*
SC, 1310 nm single mode
20 km (12.4 miles)*
SSDTF1015-105 RJ-45
1.5 km (5,000 feet)*
SC, 1310 nm single mode
40 km (24.8 miles)*
SSDTF1016-105 RJ-45
1.5 km (5,000 feet)*
SC, 1310 nm single mode
60 km (37.3 miles)*
SSDTF1017-105 RJ-45
1.5 km (5,000 feet)*
SC, 1550 nm single mode
80 km (49.7 miles)*
SSDTF1018-105 RJ-45
1.5 km (5,000 feet)*
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
SSDTF1022-105 RJ-45
1.5 km (5,000 feet)*
ST, 1310 nm single mode
15 km (9.3 miles)*
SSDTF1025-105 RJ-45
1.5 km (5,000 feet)*
MT-RJ, 1310 nm single mode
20 km (12.4 miles)*
User’s Guide
SSDTF10xx-10x
Stand-Alone Media Converter
•T1 / E1 with Remote Management
• Copper to Fiber
Transition Networks SSDTF10xx-10x series media
converters encode and decode T1 or E1 twisted-pair
copper signals over fiber optic cable to extend the
distance and transmission reliability of high-speed
T1 or E1 data traffic. The device is framing independent (as ESF vs. D4) and supports all
common line codes (e.g., AMI, B8ZS, HDB3).
The SSDTF10xx-10x is designed to be installed in pairs. For example, install one
SSDTF1011-105 as the “local” media converter and another SSDTF1011-105 as the
“remote” media converter.

224-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
(TX) = transmit (RX) = receive
* Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
** SSDTF1029-105 and -106 are intended to be installed in the same network where
one is the local converter and the other is the remote converter.
*** SSDTF1029-107 and -108 are intended to be installed in the same network where
one is the local converter and the other is the remote converter.
Note: The chassis version of the media converter is CSDTF10xx-10x. For more
information, see the CSDTF10xx-10x user’s guide on-line at: www.transition.com
Optional Accessories (sold separately)
Part Number Port One - Copper Port Two - Single Fiber Optic
SSDTF1029-105 ** RJ-45
1.5 km (5,000 feet)*
SC, 1310 mn (TX)/1550 nm (RX)
single mode, 20 km (12.4 miles)*
SSDTF1029-106 ** RJ-45
1.5 km (5,000 feet)*
SC, 1550 mn (TX)/1310 nm (RX)
single mode, 20 km (12.4 miles)*
SSDTF1029-107 *** RJ-45
1.5 km (5,000 feet)*
SC, 1310 mn (TX)/1550 nm (RX)
single mode, 40 km (24.8 miles)*
SSDTF1029-108 *** RJ-45
1.5 km (5,000 feet)*
SC, 1550 mn (TX)/1310 nm (RX)
single mode, 40 km (24.8 miles)*
Part Number Description
SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone
Output: 12.6VDC, 1.0 A
SPS-1872-PS Optional External Power Supply; 18-72VDC Piggy-back;
Output: 12.6VDC, 1.0 A
E-MCR-04 12-Slot media converter Rack (includes universal internal power
supply) 17 x 15 x 5 in. (432 x 381 x 127 mm)
WMBL Optional Wall Mount Brackets
Length: 4.0 in. (102 mm), Fits converter length: 4.7 in. (119 mm)
WMBV Optional Vertical Mount Bracket; 5.0 in. (127 mm)
WMBD Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)
WMBD-F Optional DIN Rail Mount Bracket (flat); 3.3in. (84 mm)
[email protected] -- Click the “Transition Now” link for a live Web chat. 3
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge precautions
when setting the jumper and switches. Failure to observe this caution could result in
damage to, and subsequent failure of, the media converter.
Set the hardware/software jumper
The hardware/software jumper is located on the circuit board inside the media
converter housing.
Hardware: The media converter mode is determined
by the switch settings.
Software: The media converter mode is determined
by the most-recently saved, on-board
microprocessor settings.
To set the two-position jumper:
1. Using a small screwdriver, remove the four (4) screws that secure the cover and
carefully remove the cover from the media converter.
2. The jumper is located on the circuit board and is labeled “H” and “S”.
3. Using small needle-nosed pliers or similar device, move the jumper to the
desired position. (Refer to the above drawing.)
4. Carefully replace the cover on the media converter and replace the four (4)
screws that secure the cover to the media converter.
Set the MDI/MDI-X switch (hardware mode only)
The MDI/MDI-X switch is located on the side of the media converter. This switch
allows the network administrator to use straight-through cable in installations where
crossover configuration cable is required. Use a small flat-blade screwdriver or a
similar device to set the recessed switch.
Set the switch to MDI if using
straight-through copper cable to
connect two unlike devices.
Set the switch to MDI-X if using
crossover copper cable to connect
two like devices.

424-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
Installation -- Continued
Set the loop-back switch
Hardware mode:
The loop-back switch is located on the front panel of the media converter and is
used for installation and network debugging procedures.
To set the switch, use a small flat-blade screwdriver or a
similar device (see the drawing to the right).
CL (Copper loop-back) Enable loop-back on the local copper interface.
-- (Center Position) Normal operation.
FL (Fiber loop-back) Enable loop-back on the local fiber interface.
Software mode:
If both media converters are under software control, the network administrator can
initiate the loop-back test function on the copper interface (local or remote) or on
the fiber interface (local or remote). These four loop-back test scenarios are
described in detail on page 14.
Set the configuration switches
The configuration switches are located on the side of the media converter and are
used to configure the media converter for various network conditions.
The switches are labeled 1 through 8 on the media converter housing top. There are
two sets (a “left, SW 2” and a “right, SW 1”) each with four switches labeled 1
through 4 (see the drawing below).
Use a small, flat-blade screwdriver or a similar device to set the recessed switches.
Transmit all ones (switches 1 & 2, left set, SW 2)
The Transmit All Ones function allows the insertion of an “all ones” pattern on the
copper and/or fiber interface when the signal detect is lost, creating an alarm
condition at the device connected to the interface.
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
Installation -- Continued
Switch 1, Copper -- transmit all ones
UP - Disables the transmit all ones
function on the copper interface.
DOWN - Transmits an “all ones” pattern
on the copper interface when the signal
detect on the fiber interface is lost.
Switch 2, Fiber -- transmit all ones
UP - Disables the transmit all ones function
on the fiber interface.
DOWN - Transmits an “all ones” pattern on
the fiber interface when the signal detect on
the copper interface is lost.
Select T1 configuration (switches 3 & 4, left set, SW2)
Use switches 3 and 4 to configure the media converter for T1 configuration.
Switch 3, long haul/short haul (T1 only)
UP - Short haul.
DOWN - Long haul.
Switch 4, T1 / E1
UP - T1 configuration.
Set switches 1, 2, 3, and 4 on the right
set for the required network cable
settings (see pages 6 and 7).
Select E1 configuration (switch 4, left set, SW 2)
Use switch 4 to configure the media converter for E1 configuration.
Switch 4, T1 / E1
DOWN- E1 configuration.
The default network cable setting is 3.0 V, 120
ohm.
Switch 3 on the left set and switches 1, 2, 3, and
4 on the right set are disabled.

624-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
Installation -- Continued
Settings for T1 configuration (right switch set, SW 1)
T1/long-haul signal
Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the
drawing below).
Use switches 1 and 2 on the right switch set to select the proper network cable
settings. The drawing below lists the four options.
(Switches 3 and 4 on the right switch
set are not used for configuring
T1/long- haul signals.)
[email protected] -- Click the “Transition Now” link for a live Web chat. 7
Installation -- Continued
T1/short-haul signal
Use switches 3 and 4 on the left switch set to select T1/short-haul signal (see the
drawing below).
Use switches 1, 2, and 3 on the right switch set to select the proper network cable
settings. The drawing below lists the seven options.
(Switch 4 on the right switch set is
not used for configuring T1/short-
haul signals.)

824-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
Installation -- Continued
Install the copper cable
1. Locate or build twisted-pair copper cables that are compliant with the
specifications on page 11 with RJ-45 connectors at both ends.
2. Ensure that the MDI/MDI-X switch is set according to the network conditions
(see page 3).
3. Connect the RJ-45 connector at one end of cable to the RJ-45 port on the
media converter.
4. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on
the other device (switch, workstation, etc.).
Install the fiber cable
1. Locate or build fiber cables with male, two-stranded TX to RX connectors
installed at both ends.
2. Connect the fiber cables to the local SSDTF10xx-10x media converter as
described:
• Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the remote SSDTF10xx-10x media converter as
described:
• Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
[email protected] -- Click the “Transition Now” link for a live Web chat. 9
Operation
After installation, the media converter should function without operator
intervention. Use the status LEDs to monitor the media converter operation in the
network.
SDC (Signal Detect/Copper) ON = the twisted-pair copper link is up.
SDF (Signal Detect/Fiber) ON = the fiber link is up.
PWR (Power) ON = the media converter is connected to
external power.
Dry-contact relay
The RJ-45 copper port has a dry-contact relay
that opens if the power, signal detect/copper, or
signal detect/fiber are lost. The operational
rating on pins 3 and 6 are 0-30 VDC, 100 mA
(maximum).
Remote management function
A remote, stand-alone media converter (revision SSDTF10xx-105 or higher) can be
managed when connected to a local CSDTF10xx-105 media converter. Please note
that in a managed network, both the local and remote media converters must be set to
“software” mode (see page 3). For more information, see the SNMP section in the
CSDTF10xx-10x manual online at: www.transition.com
Installation -- Continued
Power the media converter
Note: The external power supply provided with this product is UL listed by the
power supply’s manufacturer.
1. Install the power adapter cord to the back of the media converter.
2. Connect the power adapter plug to AC power.
3. Verify that the media converter is powered by observing the illuminated LED
power indicator light.
For DC power, consult the user’s guide for the Transition Networks SPS1872-xx
DC external power supply for powering the media converter.

10 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
Cable Specifications
Fiber cable
single mode fiber (recommended): 9 μm
Multimode fiber (recommended): 62.5/125 μm
Multimode fiber (optional): 100/140, 85/140, 50/125 μm
SSDTF1011-105 850 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Link Budget: 13.5 dB
SSDTF1012-105 1310 nm single mode
Fiber-optic Transmitter Power: min: -27.0 dBm max: -10.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -14.0 dBm
Link Budget: 7.0 dB
SSDTF1013-105 850 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Link Budget: 13.5 dB
SSDTF1014-105 1310 nm single mode
Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm
Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm
Link Budget: 16.0 dB
SSDTF1015-105 1310 nm single mode
Fiber Optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm
Fiber Optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm
Link Budget: 30.0 dB
SSDTF1016-105 1310 nm single mode
Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm
Fiber-optic Receiver Sensitivity: min: -38.0 dBm max: -8.0 dBm
Link Budget: 33.0 dB
SSDTF1017-105 1550 nm single mode
Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm
Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm
Link Budget: 29.0 dB
SSDTF1018-105 1300 nm multimode
Fiber-optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm
Fiber-optic Receiver Sensitivity: min: -33.5 dBm max: -14.0 dBm
Link Budget: 14.5 dB
SSDTF1022-105 1310 nm single mode
Fiber Optic Transmitter Power: min: -15.0 dBm max: -5.0 dBm
Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -14.0 dBm
Link Budget: 10.0 dB
SSDTF1025-105 1310 nm single mode
Fiber-optic Transmitter Power: min: -11.0 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm
Link Budget: 9.0 dB
[email protected] -- Click the “Transition Now” link for a live Web chat. 11
Cable Specifications -- Continued
Fiber cable
SSDTF1027-105 1300 nm multimode
Fiber Optic Transmitter Power: min: -19.0 dBm max: -10.0 dBm
Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm
Link Budget: 13.5 dB
SSDTF1029-105 1310 nm (TX)/1550 nm (RX) simplex
Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm
Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm
Link Budget: 19.0 dB
SSDTF1029-106 1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm
Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm
Link Budget: 19.0 dB
SSDTF1029-107 1310 nm (TX)/1550 nm (RX) simplex
SSDTF1029-108 1550 nm (TX)/1310 nm (RX) simplex
Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm
Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm
Link Budget: 25.0 dB
The fiber optic transmitters on this device meet Class I Laser safety requirements
per IEC-825/CDRH standards and comply with 21 CFR1040.10 and
21CFR1040.11.
Copper cable
Connector: RJ-45 / RJ-48C
Elec. network connection: Single 4-wire (Tip/Ring - Tip1/Ring1)
Mechanical arrangement: 8-position miniature modular jack
Usage: 1.544 Mb/s or 2.0478 Mb/s access lines
Interface codes: 04DU9 (any applicable)
Cable type:
Long Haul T1: 0db, -7.5dp, -15db, -22db
E1 (120 ohm): E1 3.0V, 120
J1 (110 ohm): 0-655’, 110
DSX-1 (100 ohm): 0-133’, 133-266’, 266-399’,
399-533’, 533-655’

12 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
Technical Specifications
For use with Transition Networks Model SSDTF10xx-10x or equivalent
Standards: Emissions: CISPR A; Telecordia TR-NWT-001089
(designed to meet; NOT tested); FCC Part 68; T1/E1
Physical layer: ITU-T, ANSI, AT&T, and ETSI; European
Technical Standard: TBR 12; British Technical
Publication: PD 7024 : 1994 (NTR 4)
Dimensions: 3.25" x 4.7" x 1" (83 mm x 119 mm x 25 mm)
Weight: 10 oz. (283 g) approximately
Power consumption: 3.7 Watts
Power supply: 12VDC, 0.8A (North America, Europe, UK)
12VDC, 1.25A (NZ, Australia, S Africa, JP, Latin Am)
(The external power supply provided with this product
is UL listed by the power supply’s manufacturer.)
MTBF: 47,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)
116,000 hours (Bellcore7 V5.0)
Environment: 0°C to 50°C (32°F to 122° F )
Storage Temp: -15°C to 65°C (5°F to 149°F)
Humidity: 10 to 90%, non condensing
Altitude: 0 to 10,000 feet
Warranty: Lifetime
The information in this user’s guide is subject to change. For the most up-to-date
information on the SSDTF10xx-10x media converter, view the user’s guide on-line at:
www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,
Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not stare into the
beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
[email protected] -- Click the “Transition Now” link for a live Web chat. 13
Troubleshooting
If the media converter fails, isolate and correct the failure by determining the answers
to the following questions and then taking the indicated action:
1. Is the PWR (Power) LED illuminated?
NO
• Is the power adapter the proper type of voltage and cycle frequency for
the AC outlet? (See “Technical Specifications” on page 12.)
• Is the power adapter properly installed in the media converter and in the
outlet?
• Does the grounded AC outlet provide power?
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 2.
2. Is the SDC (Signal Detect/Copper) LED illuminated?
NO
• Check the twisted-pair copper cable for the proper connection.
• Check the MDI/MDI-X switch for the correct twisted-pair copper cable
configuration (see page 3).
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 3.
3. Is the SDF (Signal Detect/Fiber) LED illuminated?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the local media converter are
connected to the RX and TX ports, respectively, on the remote media
converter.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 4.

14 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SSDTF10xx-10x
4. Is data transfer failing?
YES
• Verify the local copper connection by starting a local copper loop-back
(hardware mode: set the loop-back switch on the local media converter to
“CL”, software mode: enter the local copper loop-back command) and
then use a bit error test unit to run a bit error test.
• Verify the local fiber connection by starting a remote fiber loop-back
(hardware mode: set the loop-back switch on the remote media converter
to “FL”, software mode: enter the remote fiber loop-back command) and
then use a bit error test unit to run a bit error test.
• Verify the remote copper connection by starting a remote copper loop-back
(hardware mode: set the loop-back switch on the remote media converter
to “CL”, software mode: enter the remote copper loop-back command) and
then use a bit error test unit to run a bit error test.
• Verify the remote fiber connection by starting a local copper loop-back
(hardware mode: set the loop-back switch on the local media converter to
“FL”, software mode: enter the local fiber loop-back command) and then
use a bit error test unit to run a bit error test.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
NO
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
[email protected] -- Click the “Transition Now” link for a live Web chat. 15
Contact Us
Technical support
Technical support is available 24 hours a day:
U.S.A. and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, U.S.A.
Telephone: [phone]
Toll free: 800-526-9267
Fax: [phone]
Declaration of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 U.S.A.
Model: SSDTF10xx-10x Series Media Converter
Part Number: SSDTF1011-105, SSDTF1012-105, SSDTF1013-105,
SSDTF1014-105, SSDTF1015-105, SSDTF1016-105,
SSDTF1017-105, SSDTF1018-105, SSDTF1022-105,
SSDTF1025-105, SSDTF1027-105, SSDTF1029-105,
SSDTF1029-106, SSDTF1029-107, SSDTF1029-108
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the SSDTF10xx-10x to which this declaration refers is in
conformity with the following standards.
CISPR 22:1993; EN 55022:1994+A1:1995+A2:1997 Class A; EN 55024:1998; FCC
Part 15 Subpart B; EN 61000-3-2:1995+A14:2000; 61000-3-3:1995; CFR 21 subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
August 31, 2005
Stephen Anderson, Vice-President of Engineering Date

Compliance Information
CISPR22/EN55022 Class A + EN55024
CE Mark
FCC regulations
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus
set out on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
European regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses
Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen
verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques
appropriées.
Trademark notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright restrictions
© 2002-2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means -
graphic, electronic, or mechanical - without written permission from Transition Networks.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
SSDTF10xx-10x
16 Printed in the U.S.A. 33246.F