Transition Networks SGFEB1013-100 User manual

SGFEB1035-100 RJ-45
100 m (328 ft)
SC, 1000Base-LX, 1550 nm
single mode, 125 km (77.5 miles)
User’s Guide
SGFEB10xx-1xx
Stand-Alone Media Converter
•Copper to Fiber
• 10/100/1000Base-TX to 1000Base-SX/LX
• Optional Tap Port
Transition Networks SGFEB10xx-1xx series
media converters connect 10Base-TX,
100Base-TX, or 1000Base-TX twisted-pair
copper cable to 1000Base-SX or 1000Base-LX
fiber cable.
Installation . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . .6
Cable Specifications . . . . . . . . .9
Technical Specifications . . . . .11
Troubleshooting . . . . . . . . . . .12
Contact Us . . . . . . . . . . . . . . .15
Compliance Information . . . . .16
Part Number Port 1 - Copper
10/100/1000-Base-TX
Port 2 - Duplex Fiber-Optic
SGFEB1013-100 RJ-45
100 m (328 ft)
SC, 1000Base-SX, 850 nm multimode
220 m (720 ft)
SGFEB1014-100 RJ-45
100 m (328 ft)
SC, 1000Base-LX, 1310 nm
single mode, 10 km (6.2 miles)
SGFEB1015-100 RJ-45
100 m (328 ft)
SC, 1000Base-LX, 1310 nm
single mode, 25 km (15.5 miles)
SGFEB1017-100 RJ-45
100 m (328 ft)
SC, 1000Base-LX, 1550 nm
single mode, 65 km (40.4 miles)
SGFEB1024-100 RJ-45
100 m (328 ft)
SC, 1000Base-LX, 1300 nm
multimode, 2 km (1.2 miles)**
The distances listed are the typical maximum cable distance. Actual distance is
dependent upon the physical characteristics of the network installation.
** The CGFEB1024 extends 1000Base beyond 220 m. Transition Networks
cannot guarantee a full 2 km distance on every installation since the distance is
largely dependent on the quality of the fiber, cable installation and splicing.

2
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Part Number Port 1 - Copper
10/100/1000-Base-TX
Port 2 - Single Fiber-Optic
1000Base-SX, single mode
SGFEB1029-100 RJ-45
100 m (328 ft)
SC, 1310 nm (TX) / 1550 nm (RX)
20 km (12.4 miles)
SGFEB1029-101 RJ-45,
100 m (328 ft)
SC, 1550 nm (TX) / 1310 nm (RX)
20 km (12.4 miles)
Install SGFEB1029-100 and SGFEB1029-101 in the same
network where one is the local converter and the other is the
remote converter.
SGFEB1029-102 RJ-45
100 m (328 ft)
SC, 1310 nm (TX) / 1550 nm (RX)
40 km (24.9 miles)
SGFEB1029-103 RJ-45
100 m (328 ft)
SC, 1550 nm (TX) / 1310 nm (RX)
40 km (24.9 miles)
Install SGFEB1029-102 and SGFEB1029-103 in the same
network where one is the local converter and the other is the
remote converter.
The distances listed are the typical maximum cable distance. Actual distance is
dependent upon the physical characteristics of the network installation.
The SGFEB10xx-1xx single fiber-optic models are listed below:
[email protected] -- Click the “Transition Now” link for a live Web chat. 3
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Note: Third-party Multi-Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can be used in the SFMFF1040-1xx fiber port.
The following SFP transceiver modules are compatible with the SFMFF1040-1xx
converter and are available from Transition Networks (sold separately).
Part Number Duplex Fiber-Optic Port 2
TN-SFP-SX LC, 1000Base-SX, 850 nm multimode, 220-550 mm (720-1804 ft)*
TN-SFP-LX1 LC, 1000Base-LX, 1310 nm single mode, 10 km (6.2 miles)*
TN-SFP-LX3 LC, 1000Base-LX, 1310 nm single mode, 30 km (18.8 miles)*
TN-SFP-LX5 LC, 1000Base-LX, 1550 nm single mode, 50 km (31.2 miles)*
TN-SFP-LX8 LC, 1000Base-LX, 1550 nm single mode, 80 km (50.0 miles)*
SGFEB1040-1xx
Stand-Alone Media Converter
•Copper to Fiber
• 10/100/1000Base-TX to 1000Base-SX/LX
• Small Form Fact Pluggable (SFP) Fiber Port
Transition Networks CGFEB1040-1xx series media
converters connect 10Base-TX, 100Base-TX, or
1000Base-TX twisted-pair copper cable to
1000Base-SX or 1000Base-LX fiber cable.
The CGFEB1040-10x has one copper port and one
SFP port.
Copper Port 1: 10/100/1000-Base-TX
RJ-45 100 m (328 ft)

4
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the jumpers and the six-position switch. Failure to
observe this caution could result in damage to, and subsequent failure of, the
media converter.
Six-Position Switch
The six-position switch is located on the side of the media converter. Use a
small, flat-blade screwdriver (or a similar device) to set the switch according
to the site the requirements (see the drawing below).
1. Twisted-Pair Auto-Negotiation
(up) Enable Auto-Negotiation for the copper connection (see page 7).
(down) Disable Auto-Negotiation for the copper connection.
Note: Switches 2 and 3 will not function when twisted-pair Auto-
Negotiation is enabled (switch 1 = up). The media converter adopts
the speed and mode settings from the device at the other end of the
copper link.
2. Twisted-Pair 10Mbs/100Mbs
(up) Set copper connection speed to 100 Mbs.
(down) Set copper connection speed to 10 Mbs.
3. Twisted-Pair Full/Half Duplex
(up) Operate in full-duplex mode (see page 8).
++ Operate in half-duplex mode of the attached device.
(The default setting is half-duplex.)
4. Fiber Auto-Negotiation
(up) Enable Auto-Negotiation for the fiber connection (see page 7).
(down) Disable Auto-Negotiation for the fiber connection.
5. (not used)
6. Link Pass-Through
(up) Enable Link Pass-Through (see page 7).
(down) Disable Link Pass-Through.
2. TP 10Mbs/100Mbs
3. TP Half/Full-Duplex
4. Fiber Auto-Negotiation
5. (not used)
1. TP Autonegotiation
6. Link Pass Through
[email protected] -- Click the “Transition Now” link for a live Web chat. 5
Installation - Continued
Jumpers
AutoCross™ Jumper
The AutoCross feature allows either straight-through (MDI) or crossover
(MDI-X) cables to be used when connecting to 10Base-T, 100Base-TX, or
1000Base-T devices, such as hubs, transceivers, or network interface cards
(NICs). AutoCross determines the characteristics of the cable connection and
automatically configures the unit to link up, regardless of the cable
configuration.
The AutoCross jumper is located on the media converter’s circuit board (labeled
E and D -- see the figure to the right).
Enabled Either straight-through or crossover cable can be
used for all twisted-pair copper links.
Disabled Straight-through or crossover twisted-pair cable,
depending on installed site devices, MUST be
installed at EACH twisted-pair copper link.
Note: Factory default is “enable.” Transition Networks recommends leaving
the device in the “enable” mode.
Disable Autocross
Enable Autocross
ED
ED
Set the Jumper(s)
1. Using a small screwdriver, remove the four (4) screws that secure the
cover and carefully remove the cover from the media converter.
2. Locate the jumpers on the circuit board.
3. Using small needle-nosed pliers or similar device, move the jumpers to
the desired positions. (See the above drawings.)
4. Carefully replace the cover on the media converter and replace the four
(4) screws that secure the cover to the media converter.

6
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Port 2: 1000Base-SX/LX Fiber Port
1. Locate or build 1000Base-SX/LX compliant fiber cable with male, two-
stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the media converter’s 1000Base-SX/LX fiber
port (port 2) as described:
• Connect the male TX cable connector to the female TX connector.
• Connect the male RX cable connector to the female RX connector.
3. Connect the fiber cables to the 1000Base-SX-LX fiber port on the other
device (another media converter, hub, etc.) as described:
• Connect the male TX cable connector to the female RX connector.
• Connect the male RX cable connector to the female TX connector.
Connect the fiber cable
to the media converter
as shown.
Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
Installation -- Continued
Install the Cable
Port 1: 10/100/1000Base-TX Copper Port
1. Locate or build 10, 100, or 1000Base-TX compliant copper cables with
male, RJ-45 connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the media
converter’s 10/100/1000Base-TX RJ-45port (port 1).
3. Connect the RJ-45 connector at the other end of the cable to the 10, 100,
or 1000Base-TX RJ-45 port on the other device (switch, workstation,
etc.).
Note: The AutoCross feature, when enabled, allows the use of either
straight-through or crossover configuration cables.
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter
[email protected] -- Click the “Transition Now” link for a live Web chat. 7
Status LEDs
Fiber Status LEDs
The status LEDs for the 1000Base-SX-LX fiber connection (labeled DPX, LACT
and PWR) are located next to the fiber port (Port 2).
PWR power On = Connection to external AC power.
LACT link activity On = A link has been established for the fiber
connection.
Flashing = The fiber connection is transmitting or
receiving data.
DPX duplex On = Full-duplex mode for the fiber connection.
Off = Half-duplex mode for the fiber connection.
Copper Status LEDs
The status LEDs for the copper connection are integrated into the RJ-45 port.
These LEDs are not labeled on the media converter. Refer to the drawing to
the right for their locations.
Duplex/Yellow A link in half-duplex mode
Link has been established for the copper connection.
Flashing Yellow The copper connection is transmitting/receiving
data in half-duplex mode.
Green A link in full-duplex mode has been established
for the copper connection.
Flashing Green The copper connection is
transmitting/receiving data
in full-duplex mode.
Speed Off 10 Mb/s operation.
Yellow 100 Mb/s operation.
Green 1000 Mb/s operation.
Operation
Power the Media Converter
1. Connect the barrel connector on the power adapter to the media
converter’s power port (located on the back of the media converter).
2. Connect the power adapter plug to AC power.
3. Verify that the media converter is powered by observing the illuminated
LED power indicator light.
DPX
LACT
PWR
Port 2 Port 1

8
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Operation -- Continued
Product Features
Auto-Negotiation
The Auto-Negotiation feature allows the SGFEB10xx-1xx media converter to
automatically configure itself to achieve the best possible mode of operation
over a link. The media converter broadcasts its speed (10 Mb/s, 100 Mb/s, or
1000 Mb/s) and duplex capabilities (full or half) to the other devices and
negotiates the best mode of operation. Auto-Negotiation allows quick and
easy installation because the optimal link is established automatically. No
user intervention is required to determine the best mode of operation.
A scenario where the media converter is linked to a non-negotiating device is
a case where the user may want to disable Auto-Negotiation. In this instance,
the mode of operation will drop to the least common denominator between
the two devices (e.g., 100 Mb/s, half-duplex). Disabling this feature gives the
user the ability to force the connection to the best mode of operation.
NOTE: The SGFEB10xx-10x media converter also supports 1000 Mb/s fiber
Auto-Negotiation.
Link Pass-Through
The Link Pass-Through feature allows the media converter to monitor both the
fiber and copper RX (receive) ports for loss of signal. In the event of a loss of
an RX signal (1), the media converter will automatically disable the TX
(transmit) signal (2), thus, “passing through” the link loss (3). The far-end
device is automatically notified of the link loss (4), which prevents the loss of
valuable data unknowingly transmitted over an invalid link.
4
1
Media
Converter A
Media
Converter B
Near-End
Device
Far-End
Device
original fault
on the copper link media converter B disables the copper lin
k
media converter A
disables the fiber TX link
3
2
media converter B
loses the fiber RX link
[email protected] -- Click the “Transition Now” link for a live Web chat. 9
Operation -- Continued
Half-Duplex Network (512-Bit Rule)
In a half-duplex network, the maximum cable lengths are determined by the
round trip delay limitations of each Fast Ethernet collision domain. (A collision
domain is the longest path between any two terminal devices, e.g. a terminal,
switch, or router.)
The 512-Bit Rule determines the maximum length of cable permitted by
calculating the round-trip delay in bit-times (BT) of a particular collision
domain. If the result is less than or equal to 512 BT, the path is good.
For more information on the 512-Bit Rule, see the white paper titled
“Collision Domains” on the Transition Networks website at:
www.transition.com.
Full-Duplex Network
In a full-duplex network, maximum cable lengths are determined by the type
of cables that are used. See pages 1 and 2 for the cable specifications for the
different SGFEB10xx-1xx models.
The 512-Bit Rule does not apply in a full-duplex network.
Pause
Note: The “pause” feature is not supported in this product.

10
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Cable Specification
The physical characteristics must meet or exceed IEEE 802.3™ specifications.
Fiber Cable
Bit Error Rate: <10-9
Single mode fiber (recommended): 9 µm
Multimode fiber (recommended): 62.5/125 µm
Multimode fiber (optional): 100/140, 85/140, 50/125 µm
SGFEB1013-100, SGFEB1013-110 850 nm multimode
Fiber Optic Transmitter Power: min: -10.0 dBm max: -4.0 dBm
Fiber Optic Receiver Sensitivity: min: -17.0 dBm max: 0.0 dBm
Link Budget: 7.5 dB
SGFEB1014-100, SGFEB1014-110 1310 nm single mode
Fiber Optic Transmitter Power: min: -13.0 dBm max: -3.0 dBm
Fiber Optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm
Link Budget: 7.0 dB
SGFEB1015-100, SGFEB1015-110 1310 nm single mode
Fiber Optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm
Fiber Optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm
Link Budget: 15.0 dB
SGFEB1017-100, SGFEB1017-110 1550 nm single mode
Fiber Optic Transmitter Power: min: -3.0 dBm max: 2.0 dBm
Fiber Optic Receiver Sensitivity: min: -23.0 dBm max: -3.0 dBm
Link Budget: 20.0 dB
SGFEB1029-100, SGFEB1029-110 1310(TX)/1550(RX) nm single mode
Fiber Optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm
Fiber Optic Receiver Sensitivity: min: -21.0 dBm max: -3.0 dBm
Link Budget: 13.0 dB
SGFEB1029-101, SGFEB1029-111 1550(TX)/1310(RX) nm single mode
Fiber Optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm
Fiber Optic Receiver Sensitivity: min: -21.0 dBm max: -3.0 dBm
Link Budget: 13.0 dB
SGFEB1029-102, SGFEB1029-112 1310(TX)/1550(RX) nm single mode
Fiber Optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm
Fiber Optic Receiver Sensitivity: min: -23.0 dBm max: -8.0 dBm
Link Budget: 20.0 dB
SGFEB1029-103, SGFEB1029-113 1550(TX)/1310(RX) nm single mode
Fiber Optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm
Fiber Optic Receiver Sensitivity: min: -23.0 dBm max: -8.0 dBm
Link Budget: 20.0 dB
[email protected] -- Click the “Transition Now” link for a live Web chat. 11
Copper Cable
Category 5 (minimum requirement)
Gauge: 24 to 22 AWG
Attenuation: 22.0 dB /100 m @ 100 MHz
Maximum Cable Distance: 100 meters
• Straight-through OR crossover twisted-pair cable may be used.
• Shielded (STP) OR unshielded (UTP) twisted-pair cable may be used.
• All pin pairs (1&2, 3&6, 4&5, 7&8) are active.
• Use only dedicated wire pairs for the active pins:
(e.g., blue/white & white/blue, orange/white & white/orange, etc.)
• Do not use flat or silver satin wire.
Cable Specifications - Continued
Fiber Cable - Continued
SGFEB1035-100, SGFEB1035-110 1550 nm single mode
Fiber-optic Transmitter Power: min: 0.0 dBm max: +5.0 dBm
Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -8.0 dBm
Link Budget: 32.0 dB
SGFEB1024-100, SGFEB1024-110 1300 nm multimode **
Fiber Optic Transmitter Power: min: -10.0 dBm max: -4.0 dBm
Fiber Optic Receiver Sensitivity: min: -17.0 dBm max: -3.0 dBm
Link Budget: 7.0 dB
**Fiber cable for SGFEB1024-100 and SGFEB1024-110 must be
62.5/125 µm.
Product is certified by the manufacturer to comply with DHHS Rule
21/CFR, Subchapter J applicable at the date of manufacture.
CAUTION: Visible and invisible laser radiation when open. Do not stare
into the beam or view directly with optical instruments.
CAUTION: Use of controls, adjustments or the performance of
procedures other than those specified herein may result in hazardous
radiation exposure.
The fiber optic transmitters on this device meet Class I Laser safety
requirements per IEC-825/CDRH standards and comply with 21
CFR1040.10 and 21CFR1040.11.

12
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Technical Specifications
For use with Transition Networks Model SGFEB10xx-1xx.
Standards: IEEE 802.3™
Dimensions: 4.8" x 3.25" x 1.0" (122 x 82 x 25 mm)
Weight: 10 oz (283 g)
Power Consumption: 7.28 watts
Power Supply: 12VDC, 1.25 A
Data Rate (copper): 10, 100, 1000 Mb/s
Data Rate (fiber): 1000 Mb/s (operates in full-duplex only)
Latency: 64 256 1024 1518 (frame size)
1000Base-T: 3.2 4.8 10.9 14.8 micro seconds
1000Base-SX/LX: 3.2 4.8 10.9 14.8 micro seconds
Packet Size: Unicast MAC address: 4K bytes
Maximum packet size: 1536 bytes
Memory: 256K bytes (2 Mbit)
MTBF 48,000 hours (MIL217F2V5.0) (MIL-HDBK-217F)
122,000 hours (Bellcore7 V5.0)
Environment: Tmra*: 0°C to 50°C (32°F to 122°F)
Storage Temp: -40°C to 85°C (-40°F to 185°F)
Humidity: 5% to 95°C%, non-condensing
Altitude: 0 to 10,000 feet
Warranty: Lifetime
*Manufacturer’s rated ambient temperature.
The information in this user’s guide is subject to change. For the most up-to-date
information, see the user’s guide on-line at www.transition.com.
13
[email protected] -- Click the “Transition Now” link for a live Web chat.
Troubleshooting
1. Is the Power LED illuminated?
NO
• Ensure that the power adapter is the proper type of voltage and cycle
frequency for the outlet (See “Power Supply” on page 11.)
• Ensure the power adapter is properly installed in the media converter
and in the grounded outlet.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 2.
2. Is the Duplex LED illuminated yellow OR green?
NO
• Check the copper cables for proper connection.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES - Yellow
• The media converter has selected half-duplex mode. If this is not the
correct mode, disconnect and reconnect the copper cable to restart
the initialization process.
• Proceed to step 3.
YES - Green
• The media converter has selected full-duplex mode. If this is not the
correct mode, disconnect and reconnect the copper cable to restart
the initialization process.
• Proceed to step 3.
3. Is the LACT LED illuminated?
NO
• Check the fiber cables for proper connection.
• Verify that the TX and RX cables on the media converter are
connected to the RX and TX ports, respectively, on the other device.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES
• Proceed to step 4.
4. Is the DPX LED illuminated?
YES
• The converter has selected full-duplex mode for the fiber link. If this
is not the correct mode, disconnect and reconnect the fiber cable to
restart the initialization process.
• Proceed to step 5.
NO
• The converter has selected half-duplex mode for the fiber link. If this
is not the correct mode, disconnect and reconnect the fiber cable to
restart the initialization process.
• Proceed to step 5.

14
SGFEB10xx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Troubleshooting -- Continued
5. Is the Speed LED illuminated?
NO
• The media converter has selected 10 Mb/s operation. If this is not the
correct speed, disconnect and reconnect the copper cable to restart
the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES - Flashing Yellow
• The media converter has selected 100 Mb/s speed. If this is not the
correct speed, disconnect and reconnect the copper cable to restart
the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
YES - Flashing Green
• The media converter has selected 1000 Mb/s operation. If this is not
the correct speed, disconnect and reconnect the copper cable to
restart the initialization process.
• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.
Declaration of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 U.S.A.
Model: SGFEB10xx-1xx Series Media Converters
Part Number(s): SGFEB1013-100, SGFEB1014-100, SGFEB1015-100, SGFEB1017-100,
SGFEB1024-100, SGFEB1035-100, SGFEB1029-100, SGFEB1040-100
SGFEB1029-101, SGFEB1029-102, SGFEB1029-103, SGFEB1013-110,
SGFEB1014-110, SGFEB1015-110, SGFEB1017-110, SGFEB1024-110,
SGFEB1029-110, SGFEB1029-111, SGFEB1029-112, SGFEB1029-113,
SGFEB1035-110
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the
SGFEB10xx-1xx to which this declaration refers is in conformity
with the following standards.
CISPR 22: 1993; EN 55022:1994 A1:1995 A2:1997 Class A; EN 55024:1998; FCC Part 15 Subpart B;
21 CFR subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and
Standard(s).
December 7, 2005____
Stephen Anderson, Vice-President of Engineering Date
[email protected] -- Click the “Transition Now” link for a live Web chat. 15
Contact Us
Technical Support
Technical support is available 24 hours a day.
US and Canada: 1-800-260-1312
International: 00-1-952-941-7600
Transition Now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-Based Seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, U.S.A.
telephone: [phone]
toll free: 800-526-9267
fax: [phone]

Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2003-2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any
means - graphic, electronic, or mechanical - without written permission from Transition
Networks.
Compliance Information
CISPR22/EN55022 Class A + EN55024
CE Mark
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at the user's own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus
set out on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la lass A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb
dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für
Gegenmaßnahmen verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer
des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures
spécifiques appropriées.
In accordance with European Union Directive 2002/96/EC of the European
Parliament and of the Council of 27 January 2003, Transition Networks will accept
post usage returns of this product for proper disposal. The contact information for
this activity can be found in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-
Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
Printed in the U.S.A 33277.F
16