Transition Networks SISPM1040-182D User manual

8 10/100TX + 2 10/100/1000T/Mini-GBIC
Combo with 8 PoE Injector Industrial Switch
User Manual
SISPM1040-182D
Version 1.01
October, 2009

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Revision History
Document
Release Date Revision Initials
1.00 Oct 31, 2008 First release A.E.F
1.01 Oct 21, 2009 Corrections A.E.F

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
The contents of this manual are based on the table below listing
firmware version, kernel version, and hardware version. If the
switch functions are different from the description of the manual,
please contact the local sale dealer for more information.
Firmware Version

V1.00
Kernel Version

V1.56
Hardware Version

----------
Notice

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Content
Chapter 1 Introduction......................................... 1
1.1 Hardware Features...................................... 1
1.2 Software Features ....................................... 5
1.3 Package Contents ....................................... 8
Chapter 2 Hardware Description ........................ 9
2.1 Physical Dimension ..................................... 9
2.2 Front Panel.................................................. 9
2.3 Bottom View .............................................. 10
2.4 LED Indicators........................................... 11
Chapter 3 Hardware Installation ....................... 13
3.1 Installation Steps ....................................... 13
3.2 DIN-Rail Mounting ..................................... 14
3.3 Wall Mount Plate Mounting ....................... 16
3.4 Wiring the Power Inputs ............................ 17
3.5 Wiring the Fault Alarm Contact ................. 18
3.6 Cabling ...................................................... 19
Chapter 4 Network Application......................... 23
4.1 X-Ring Application..................................... 25
4.2 Coupling Ring Application ......................... 26
4.3 Dual Homing Application ........................... 27
4.4 Dual Ring Application ................................ 28
Chapter 5 Console Management ...................... 29
5.1 Connecting to the Console Port ................ 29
5.2 Pin Assignment ......................................... 29

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
5.3 Login in the Console Interface................... 30
5.4 CLI Management....................................... 32
5.5 Commands Level ...................................... 32
Chapter 6 Web-Based Management................. 34
6.1 About Web-based Management................ 34
6.2 Preparing for Web Management ............... 34
6.3 System Login............................................. 35
6.4 System Information ................................... 36
6.5 IP Configuration......................................... 37
6.6 DHCP Server............................................. 39
6.7 TFTP ......................................................... 43
6.8 System Event Log ..................................... 46
6.9 Fault Relay Alarm...................................... 52
6.10 SNTP Configuration ................................. 53
6.11 IP Security ................................................ 57
6.12 User Authentication .................................. 59
6.13 Port Statistics ........................................... 60
6.14 Port Control .............................................. 62
6.15 Port Trunk................................................. 64
6.16 Port Mirroring............................................ 74
6.17 Rate Limiting ............................................ 75
6.18 VLAN configuration .................................. 77
6.19 Rapid Spanning Tree ............................... 87
6.20 SNMP Configuration................................. 91
6.21 QoS Configuration.................................... 97

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
6.22 IGMP Configuration................................ 100
6.23 X-Ring..................................................... 102
6.24 LLDP Configuration ................................ 105
6.25 Security—802.1X/Radius Configuration. 106
6.26 MAC Address Table ............................... 110
6.27 Power over Ethernet............................... 115
6.28 Factory Default ....................................... 117
6.29 Save Configuration................................. 118
6.30 System Reboot....................................... 119
Troubles shooting ................................................. 120
Appendix A—RJ-45 Pin Assignment ................... 121
RJ-45 Pin Assignments........................................ 121
RJ-45 Pin Assignment of PoE.............................. 124
Appendix B—Command Sets............................... 126
System Commands Set ....................................... 126
Port Commands Set............................................. 128
Trunk Commands Set .......................................... 131
VLAN Commands Set.......................................... 132
Spanning Tree Commands Set............................ 134
QOS Commands Set ........................................... 137
IGMP Commands Set .......................................... 138
Mac / Filter Table Commands Set ....................... 138
SNMP Commands Set......................................... 139
Port Mirroring Commands Set ............................. 142
802.1x Commands Set ........................................ 142

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
TFTP Commands Set .......................................... 145
SystemLog, SMTP and Event Commands Set.... 145
SNTP Commands Set.......................................... 147
X-ring Commands Set.......................................... 148

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Chapter 1 Introduction
The 8 10/100TX + 2 10/100/1000T/Mini-GBIC Combo w/8 PoE Injectors Managed
Industrial Switch is a cost-effective solution and meets the high reliability requirements
demanded by industrial applications. Fiber can extend the connection distance to
increases the network elasticity and performance. In addition, the industrial switch
provides the PoE function for Powered Devices to receive power as well as data over
the RJ-45 cable.
1.1 Hardware Features
Standard
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX/ FX
IEEE802.3ab 1000Base-T
IEEE802.3z Gigabit fiber
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.3af Power over Ethernet
IEEE802.1d Spanning Tree/ IEEE802.1w Rapid Spanning
Tree
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag
IEEE 802.1x User Authentication (Radius)
IEEE802.1ab LLDP
Switch
Architecture
Back-plane (Switching Fabric): 5.6Gbps
Packet throughput ability(Full-Duplex): 8.3Mpps @64bytes
Transfer Rate
14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Fiber Ethernet port
Packet Buffer 1Mbits

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
2
MAC Address 8K MAC address table
Flash ROM 4Mbytes
DRAM 32Mbytes
Connector
10/100TX: 8 x RJ-45
10/100/1000T/ Mini-GBIC Combo: 2 x RJ-45 + 2 x
100/1000 SFP sockets
RS-232 connector: RJ-45 type
Network Cable
10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
1000Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable
EIA/TIA-568 100-ohm (100m)
Optical Fiber
Distance:
Multi mode:
0 to 5 km, 1300 nm (50/125 ȝm, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125 ȝm, 500 MHz*km)
Single mode:
0 to 40 km, 1310 nm (9/125 ȝm, 3.5 PS/(nm*km))
0 to 80 km, 1550 nm (9/125 ȝm, 19 PS/(nm*km))
Min. TX Output:
Multi mode: -20 dBm
Single mode: 0 to 40 km, -5 dBm; 0 to 80 km, -5 dBm
Max. TX Output:
Multi mode: -14 dBm
Single mode: 0 to 40 km, 0 dBm; 0 to 80 km, 0 dBm
Sensitivity:
-36 to -32 dBm (Single mode); -34 to -30 dBm (Multi mode)
PoE pin
assignment
RJ-45 port # 1~# 8 support IEEE 802.3af End-point,
Alternative A mode. Per port provides 15.4W ability.

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
3
Positive (VCC+): RJ-45 pin 1,2.
Negative (VCC-): RJ-45 pin 3,6.
Protocol CSMA/CD
LED
Per unit: Power (Green), Power 1 (Green), Power 2
(Green), Fault (Red), Master (Green), FWD (Green)
8 port 10/100: Link/Activity (Green), Full duplex/Collision
(Amber)
SFP port: LNK/ACT(Green), 1000T: LNK/ACT(Green),
1000M(Green)
Power Supply
External Power Supply: DC 48V, Redundant power DC 48V
and connective removable terminal block for master and
slave power
Power
Consumption 116Watts (Full load)
Operating
Humidity 5% to 95% (Non-condensing)
Operating
Temperature
Standard: -10oC ~ 60oC
Wide Operating Temperature: -40oC ~ 75oC
Storage
Temperature -40oC ~ 85oC
Case Dimension IP-30, 72mm (W) x 105mm (D) x 152mm (H)
Fan Number 0
Installation DIN rail and wall mount ear
EMI
FCC Class A, CE EN61000-4-2, CE EN61000-4-3, CE EN-
61000-4-4, CE EN61000-4-5,
CE EN61000-4-6, CE EN61000-4-8, CE EN61000-4-11, CE
EN61000-4-12, CE EN61000-6-2, CE EN61000-6-4
Safety UL, cUL, CE/EN60950-1

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
4
Stability Testing IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock),
IEC60068-2-6 (Vibration)

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
5
1.2 Software Features
Management SNMP v1 v2c, v3/ Web/Telnet/CLI
SNMP MIB
RFC 1215 Trap, RFC1213 MIBII, RFC 1157 SNMP MIB, RFC 1493
Bridge MIB, RFC 2674 VLAN MIB, RFC 1643 , RFC 1757, RSTP MIB,
Private MIB, LLDP MIB
VLAN
Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K,
VLAN ID can be assigned from 1 to 4096.)
GVRP (256 Groups)
Port Trunk with
LACP
LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk
members
LLDP** Supports LLDP allowing switch to advertise its identification
and capability on the LAN
Spanning tree IEEE802.1d spanning tree
IEEE802.1w rapid spanning tree.
X-Ring
Supports X-ring, Dual Homing, Couple Ring and Dual Ring
Topology
Provides redundant backup feature and the recovery time
below 20ms
Quality of Service The quality of service determined by port, Tag and IPv4
Type of service, IPv4/IPv6 Different Service
Class of Service Supports IEEE802.1p class of service, per port provides 4
priority queues
Port Security Supports 100 entries of MAC address for static MAC and
another 100 for MAC filter

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
6
Port Mirror Supports 3 mirroring types: “RX, TX and Both packet”.
IGMP Supports IGMP snooping v1,v2
256 multicast groups and IGMP query
IP Security
Supports 10 IP addresses that have permission to access
the switch management and to prevent unauthorized
intruder.
Login Security Supports IEEE802.1X Authentication/RADIUS
Bandwidth
Control
Support ingress packet filter and egress packet limit
The egress rate control supports all of packet type and the
limit rates are 100K~102400Kbps(10/100),
100K~256000Kbps(1000)
Ingress filter packet type combination rules are
Broadcast/Multicast/Unknown Unicast packet,
Broadcast/Multicast packet, Broadcast packet only and all
of packet. The packet filter rate can be set from
100K~102400Kbps(10/100), 100K~256000Kbps(1000)
Flow Control Supports Flow Control for Full-duplex and Back Pressure
for Half-duplex
System Log Supports System log record and remote system log server
SMTP Supports SMTP Server and 6 e-mail accounts for receiving
event alert
Relay Alarm Provides one relay output for port breakdown, power fail
Alarm Relay current carry ability: 1A @ DC24V
SNMP Trap
1. Cold start
2. Link down
3. Link up

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
7
4. Authorization fail
5. PD disconnect trap-PoE port event
DHCP Provides DHCP Client/ DHCP Server/ Port and IP Binding
DNS Provides DNS client feature and supports Primary and
Secondary DNS server
SNTP Supports SNTP to synchronize system clock in Internet
Firmware Update Supports TFTP firmware update, TFTP backup and restore.
Configuration
Upload/Download
Supports binary format configuration file for system quick
installation
ifAlias Each port allows importing 128bits of alphabetic string of
word on SNMP and CLI interface

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
8
1.3 Package Contents
Please refer to the package content list below to verify them against the checklist.
8 10/100TX + 2 10/100/1000T/Mini-GBIC Combo w/8 PoE Injectors Managed
Industrial Switch x 1
User manual x 1
Pluggable Terminal Block x 1
Mounting plate x 2
RJ-45 to DB9-Female cable x 1
Compare the contents of the industrial switch with the standard checklist above. If any
item is damaged or missing, please contact the local dealer for service.

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Chapter 2 Hardware Description
This chapter will describe the Industrial switch’s hardware spec, port, cabling information,
and wiring installation.
2.1 Physical Dimension
8 10/100TX w/ X-Ring Managed Industrial Switch dimension (W x D x H) is 72mm x
105mm x 152mm
2.2 Front Panel
The Front Panel of the 8 10/100TX w/ X-Ring Managed Industrial Switch is shown as
below:
Front Panel of the industrial switch

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
10
2.3 Bottom View
The bottom panel of the 8 10/100TX w/ X-Ring Managed Industrial Switch has one
terminal block connector for two (2) DC power inputs and one fault alarm.
Bottom Panel of the industrial switch

Transition Networks SISPM1040-182D
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
2.4 LED Indicators
The diagnostic LEDs that provide real-time status information are located on the front
panel of the industrial switch. The following table provides the description of the LED
status and their meanings.
LED Color Status Meaning
On The switch unit is powered on
PWR Green
Off No power
On The industrial switch is the master of the
X-Ring group
R.M. Green
Off The industrial switch is not a ring master in
the X-Ring group
On Power 1 is active
PWR1 Green
Off Power 1 is inactive
On Power 2 is active
PWR2 Green
Off Power 2 is inactive
On Power or port failure
FAULT Red
Off No failures
On A network device is detected.
Blinking The port is transmitting or receiving packets
from the TX device.
Green
(Upper LED)
Off No device attached
On 1000M
P9, P10 (RJ-
45)
Green
(Lower LED) Off 10/100M

Transition Networks SISPM1040-182D-LR
Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
12
On The SFP port is linking
Blinks The port is transmitting or receiving packets
from the TX device.
Link/Active
(P9, P10
SFP)
Green
Off No device attached
On A network device is detected.
Blinking The port is transmitting or receiving packets
from the TX device.
Green
Off No device attached
On The port is operating in full-duplex mode.
Blinking Collision of Packets occurs.
P1 ~ P8
Amber
Off The port is in half-duplex mode or no device
is attached.
Green A powered device is connected utilizing
Power over Ethernet on the port
FWD (P1 ~
P8) Green
Off No device is connected or power forwarding
fails