Transition Networks SISPM1040-3248-L User manual

TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 1of 250


SISPM1040‐3248‐L
RackMountIndustrialEthernetSwitch
ManagedHardenedPoE+Switch,(24)10/100/1000Base‐TPoE+ports+
(4)100/1000Base‐XSFP/RJ‐45Combo+(4)1G/10GSFP+

CLIReference
33764Rev.A



TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 2of 250
SafetyWarningsandCautions
Theseproductsarenotintendedforuseinlifesupportproductswherefailureofaproductcouldreasonablybeexpectedto
resultindeathorpersonalinjury.Anyoneusingthisproductinsuchanapplicationwithoutexpresswrittenconsentofan
officerofTransitionNetworksdoessoattheirownrisk,andagreestofullyindemnifyTransitionNetworksforanydamages
thatmayresultfromsuchuseorsale.
Attention:thisproduct,likeallelectronicproducts,usessemiconductorsthatcanbedamagedbyESD(electrostaticdischarge).
Alwaysobserveappropriateprecautionswhenhandling.
NOTE: Emphasizesimportantinformationorcallsyourattentiontorelatedfeaturesorinstructions.
WARNING: Alertsyoutoapotentialhazardthatcouldcausepersonalinjury.
CAUTION: Alertsyoutoapotentialhazardthatcouldcauselossofdata,ordamagethesystemorequipment.
SISPM1040‐3248‐LRackMountIndustrialEthernetSwitchCLIReference,33764Rev.A

RecordofRevisions
RevDateDescriptionofChanges
A10/17/18InitialreleaseatFWv8.40.428.
Trademarknotice:Alltrademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.Allotherproducts
orservicenamesusedinthispublicationareforidentificationpurposesonly,andmaybetrademarksorregistered
trademarksoftheirrespectivecompanies.Allothertrademarksorregisteredtrademarksmentionedhereinaretheproperty
oftheirrespectiveholders.
Copyrightrestrictions:©2018TransitionNetworks,Inc.Allrightsreserved.Nopartofthisworkmaybereproducedorused
inanyformorbyanymeans(graphic,electronic,ormechanical)withoutwrittenpermissionfromTransitionNetworks.
Addresscommentsonthisproductormanualto:
TransitionNetworksInc.
10900RedCircleDrive,Minnetonka,MN55343
tel:+1.952.941.7600|tollfree:1.800.526.9267|fax:952.941.2322
[email protected]|[email protected]|[email protected]
web:https://www.transition.com


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 3of 250
Contents
SafetyWarningsandCautions...........................................................................................................................2
Chapter1‐Introduction....................................................................................................................................5
1‐1KeyFeatures.......................................................................................................................................................5
1‐2ManualOverview...............................................................................................................................................5
1‐3RelatedManuals................................................................................................................................................5
Chapter2–CLIManagement.............................................................................................................................6
2‐1ConnecttotheNetwork....................................................................................................................................6
2‐2LogintotheCLI..................................................................................................................................................6
2‐3CLICommandModes.........................................................................................................................................6
2‐3.1ChangeBetweenCommandModes...........................................................................................................7
2‐4GlobalCommands..............................................................................................................................................7
Chapter3–CableDiagCommands.....................................................................................................................9
Chapter4–ClearCommands...........................................................................................................................10
Chapter5–ConfigModeCommands...............................................................................................................19
Chapter6‐ConfigureInterfaceCommands.....................................................................................................91
Chapter7–CopyCommands.........................................................................................................................123
Chapter8–DeleteCommands......................................................................................................................124
Chapter9–DirCommands............................................................................................................................125
Chapter10–DisableCommands...................................................................................................................126
Chapter11–DoCommands..........................................................................................................................127
Chapter12–Dot1xCommands......................................................................................................................128
Chapter13–EnableCommands....................................................................................................................129
Chapter14‐ERPSCommands........................................................................................................................130
Chapter15‐FirmwareCommands.................................................................................................................131
Chapter16‐IPCommands.............................................................................................................................132
Chapter17‐IperfCommands........................................................................................................................133
Chapter18‐Iperf3Commands......................................................................................................................134
Chapter19–IPv6Commands.........................................................................................................................135
Chapter20–LinkOAMCommands................................................................................................................136
Chapter21‐MoreCommands.......................................................................................................................137
Chapter22‐PingCommands.........................................................................................................................138
Chapter23–PlatformCommands.................................................................................................................139

TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 4of 250
Chapter24–PTPCommands.........................................................................................................................141
Chapter25‐ReloadCommands.....................................................................................................................146
Chapter26–SendCommands.......................................................................................................................147
Chapter27–ShowCommands......................................................................................................................148
Chapter28‐TerminalCommands..................................................................................................................188
Chapter29–TracerouteCommands..............................................................................................................188
Chapter30–CommandSummary.................................................................................................................189
Chapter31–Service,Warranty&TechSupport............................................................................................247
31‐1LimitedLifetimeWarranty..........................................................................................................................247
31‐2RecordDeviceandSystemInformation.....................................................................................................248
31‐3ContactUs...................................................................................................................................................249



TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 5of 250
Chapter1‐Introduction
TheSISPM1040‐3248‐Lswitchisanext‐generationrackmountindustrialgradeEthernetswitchesoffering
powerfulL2andbasicL3featureswithadvancedfunctionalityandusability.Inadditiontotheextensive
managementfeatures,theSISPM1040‐3248‐LalsoprovidesCarrierEthernetfeaturessuchasOAM,CFM,ERPS,
EPS,andPTPv2whichmakethemsuitableforindustrialandCarrierEthernetapplications.
TheSISPM1040‐3248‐Ldelivers16/24(10M/100M/1G)RJ45/PoE+(support802.3at/af,andtotalupto
250W/370W)ports,4GbESFPports,2/4GbE/10GSFP+portsandRJ45Consoleport.TheSISPM1040‐3248‐L
provideshighhardwareperformanceandenvironmentflexibilityforindustrialapplications.
1‐1KeyFeatures
DMS(DeviceManagementSystem)builtin
CarrierEthernetfeaturesforeasiermanageability,securityandQoS
IEEE1588v2PTP(TC)
IEEE802.3ahOAM
IEEE802.1agCFM(ITU‐TY.1731Performancemonitoring)
ITU‐TG.8031EthernetLinearProtectionSwitching(EPS)
ITU‐TG.8032EthernetRingProtectionSwitching(ERPS)
DHCPServer
IPv4/IPv6L3Staticroute
OSPF(OpenShortestPathFirst)
SharedandIndependentVLANLearning(SVLandIVL)
1‐2ManualOverview
ThismanualdescribeshowtooperateCLItomanagetheSISPM1040‐3248‐Lswitch.Thismanualisintendedfor
usebynetworkadministratorswhoareresponsibleforoperatingandmaintainingnetworkequipment;
consequently,itassumesabasicworkingknowledgeofgeneralswitchfunctions,InternetProtocol(IP),and
TelnetProtocol.
1‐3RelatedManuals
AprintedQuickStartGuideisshippedwitheachdevice.
ForTransitionNetworksDrivers,Firmware,etc.gototheProductSupportwebpage(logonrequired).
ForTransitionNetworksManuals,Brochures,DataSheets,etc.gototheSupportLibrary(nologonrequired).
ForSFPmanualsseeTransitionNetworksSFPwebpage.
NotethatthismanualprovideslinkstothirdpartywebsitesforwhichTransitionNetworksisnotresponsible.
Otherrelatedmanualsarelistedbelow.
SISPM1040‐3248‐LQuickStartGuide,33761
SISPM1040‐3248‐LInstallGuide,33762
SISPM1040‐3248‐LWebUserGuide,33763
ReleaseNotes(versionspecific)


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 6of 250
Chapter2–CLIManagement
2‐1ConnecttotheNetwork
ToconnecttothenetworkviatheCLI:
1. AttachtheRJ45serialportontheswitch’sfrontpaneltelnetconfiguration.
2. At“ComPortProperties”Menu,configuretheparametersasbelow:
Baudrate115200
Stopbits1
Databits8
Parity N
Flowcontrolnone
2‐2LogintotheCLI
Thecommandlineinterface(CLI)isatext‐basedinterface.UserscanaccesstheCLIthrougheitheradirectserial
connectiontothedeviceoraTelnetsession.ThedefaultIPaddressis192.168.1.1.Thedefaultusernameand
passwordtologinintotheswitchare:
Username:admin
Password:<none>
Note:<none>meansemptystring
Afteryouloginsuccessfully,thepromptwillbeshownas“<sys_name>#“.Seethefiguresbelow.Itmeansyou
haveadministratorlevelprivilegesandcanperformallswitchfunctions.Ifnotloggedinasanadministrator,the
promptdisplaysas“<sys_name>>”,whichmeansyouhaveguestprivilegesandcanonlyenterasubsetofthe
commandsthattheadministratorcanenter.EachCLIcommandhasitsprivilegelevel.
2‐3CLICommandModes
TheCLIisdividedintoseveralmodes.Ifauserhasenoughprivilegetorunaparticularcommand,theuserhasto
runthecommandinthecorrectmode.Toseethecommandsofthemode,entera“?”afterthesystemprompt,
andthenallcommandswillbedisplayedonthescreen.Thecommandmodesarelistedbelow:
Mode Prompt Command Function in this Mode
exec <sys_name>#
Display current configuration, diagnostics,
maintenance
config <sys_name>(config)# Configure features other than those below
Config-if <sys_name>(config-interface)# Configure ports
Config-if-vlan <sys_name>(config-if-vlan)# Configure static vlan
Config-line <sys_name>(config-line)# Line Configuration
Config-impc-profile <sys_name>(config-impc-profile)# IPMC Profile
Config-snmp-host <sys_name>(config-snmp-host)# SNMP Server Host
Config-stp-aggr <sys_name>(config-stp-aggr)# STP Aggregation
Config-dhcp-pool <sys_name>(config-dhcp-pool)# DHCP Pool Configuration


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 7of 250
Commandsresideinaspecificmodeandcanonlyberuninthatmode.Ifauserwantstorunaparticular
command,theuserhastochangetotheappropriatemode.Thecommandmodesareorganizedasatree,and
usersstartinenablemode.Thefollowingtableexplainshowtochangefromonemodetoanother.
2‐3.1ChangeBetweenCommandModes
Mode Ente
r
Mode Leave Mode
exec -- --
config Configure terminal exit
config-interfcae Interface <port-type> <port-type-list> exit
config-vlan Interface vlan <vlan_list> exit
2‐4GlobalCommands
SISPM1040‐3248‐L#?
CableDiagCableDiagnostickeyword
clearClear
configureEnterconfigurationmode
copyCopyfromsourcetodestination
deleteDeleteonefileinflash:filesystem
dirDirectoryofallfilesinflash:filesystem
disableTurnoffprivilegedcommands
doTorunexeccommandsintheconfigurationmode
dot1xIEEEStandardforport‐basedNetworkAccessControl
enableTurnonprivilegedcommands
erpsEthernetRingProtectionSwitching
exitExitfromEXECmode
firmwareFirmwareupgrade/swap
helpDescriptionoftheinteractivehelpsystem
ipIPv4commands
iperfnetworkbandwidthmeasurementtool
iperf3networkbandwidthmeasurementtool
ipv6IPv6configurationcommands
link‐oamLinkOAMconfiguration
logoutExitfromEXECmode
moreDisplayfile
noDeletetracehuntstring
pingSendICMPechomessages
platformPlatformconfiguration
ptpMiscnonpersistent1588settings.
reloadReloadsystem.
sendSendamessagetootherttylines
showDisplaystatisticscounters.
terminalSetterminallineparameters
tracerouteSendIPTraceroutemessages
SISPM1040‐3248‐L#

TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 8of 250
Command:exit
Description: ExitfromEXECmode;youmusthitEnterandthenloginagain.
Syntax: exit<cr>
Parameters:None.
Example:
SISPM1040‐3248‐L#exit
Username:
Password:

Command:help(?)
Description: Descriptionoftheinteractivehelpsystem.Thethreeformsofthe?commandare:
SISPM1040‐3248‐L#copy? (commandnospace?) givesacommanddescription.
SISPM1040‐3248‐L#copy_?(commandspace?)  liststhecommandparameters.
SISPM1040‐3248‐L#copy?? (commandnospacetwo??)liststhecommandsyntax.
Syntax: help<cr>
Parameters:None.
Example:
SISPM1040‐3248‐L#help
Helpmayberequestedatanypointinacommandbyenteringaquestionmark'?'.Ifnothing
matches,thehelplistwillbeemptyandyoumustbackupuntilenteringa'?'showsthe
availableoptions.
Twostylesofhelpareprovided:
1.Fullhelpisavailablewhenyouarereadytoenteracommandargument(e.g.'show?')and
describeseachpossibleargument.
2.Partialhelpisprovidedwhenanabbreviatedargumentisentered
andyouwanttoknowwhatargumentsmatchtheinput
(e.g.'showpr?'.)

SISPM1040‐3248‐L#

Command:logout
Description: ExitfromEXECmode;youmusthitEnterandthenloginagain.
Syntax: logout<cr>
Parameters:None.
Example:
SISPM1040‐3248‐L#logout
Username:
Password:
SISPM1040‐3248‐L#

TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 9of 250

Chapter3–CableDiagCommands
Command:CableDiag
Description: Runthecablediagnosticanddisplaytestresult.
Syntax: CableDiaginterfaceGigabitEthernet<port_type_id>
Parameters:Interface Interfacekeyword
GigabitEthernet1GigabitEthernetPort
<port_type_id>PortIDin1/1‐28
Example:
SISPM1040‐3248‐L#CableDiaginterfaceGigabitEthernet1/1
StartingCableDiagnostic‐Pleasewait
InterfaceLinkStatusTestResultLength
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐
GigabitEthernet1/1LinkDowndetecterrororcheckcablelengthisbetween7‐120
meters
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 10 of 250
Chapter4–ClearCommands
Table:clearCommands
CommandFunction
access ClearAccessmanagement
access‐list ClearAccesslist
dot1x ClearIEEEStandardforport‐basedNetworkAccessControl
eps ClearEthernetProtectionSwitching
erps ClearEthernetRingProtectionSwitching
ip ClearIPprotocol
ipv6 ClearIPv6configurationcommands
lacp ClearLACPstatistics
link‐oamClearLinkOAMstatistics
lldp ClearLLDPstatistics
logging Systemloggingmessage
mac ClearMACAddressTable
mep ClearMaintenanceEntityPoint
mvr ClearMulticastVLANRegistrationconfiguration
network‐clockClearactiveWTRtimer.
port‐securityClearPortSecurity
ptp ClearPrecisionTimingProtocolv2
sflow ClearStatisticsflow
spanning‐treeClearSTPBridge
statisticsClearstatisticsforoneormoregiveninterfaces
system Clearsystemparameters

Command:access
Description: ClearAccessmanagementStatisticsdata.
Syntax: clearaccessmanagementstatistics<cr>
Parameters: management Accessmanagementconfiguration
statistics Statisticsdata
Example:
SISPM1040‐3248‐L#clearaccessmanagement?
statisticsStatisticsdata
SISPM1040‐3248‐L#clearaccessmanagementstatistics?
<cr>
SISPM1040‐3248‐L#clearaccessmanagementstatistics
SISPM1040‐3248‐L#



TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 11 of 250
Command:access‐list
Description: ClearAccessListACEStatistics.
Syntax: clearaccess‐listacestatistics
Parameters:ace Accesslistentry
statisticsTrafficstatistics
Example:
SISPM1040‐3248‐L#clearaccess‐list?
access‐listAccesslist
SISPM1040‐3248‐L#clearaccess‐list?
aceAccesslistentry
SISPM1040‐3248‐L#clearaccess‐listace?
statisticsTrafficstatistics
SISPM1040‐3248‐L#clearaccess‐listacestatistics?
<cr>
SISPM1040‐3248‐L#clearaccess‐listacestatistics
SISPM1040‐3248‐L#

Command:dot1x
Description: ClearIEEEStandardforport‐basedNetworkAccessControlstatistics.
Syntax: cleardot1xstatistics[interface(<port_type>[<v_port_type_list>])]
Parameters: statisticsClearsthestatisticscounters
interfaceInterface
* AllswitchesorAllports
GigabitEthernet1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
<port_type_list>Portlistforallporttypes
<port_type_list>Portlistin1/1‐28
<cr>
<port_type_list>Portlistin1/1‐4
Example:
SISPM1040‐3248‐L#cleardot1xstatisticsinterfaceGigabitEthernet1/410GigabitEthernet?
<port_type_list>Portlistin1/1‐4
SISPM1040‐3248‐L#$ticsinterfaceGigabitEthernet1/410GigabitEthernet1/2


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 12 of 250
Command:eps
Description: ClearEthernetProtectionSwitching.
Syntax: cleareps<inst>wtr
Parameters: <uint>TheEPSinstancenumber.
wtrClearactiveWTR.
Example:
SISPM1040‐3248‐L#cleareps?
epsEthernetProtectionSwitching.
SISPM1040‐3248‐L#cleareps0wtr
SISPM1040‐3248‐L#
Messages:InvalidEPSinstancenumber
Error:EPSinstanceisnotcreated
Command:erps
Description: ClearEthernetRingProtectionSwitchingstatistics
Syntax: clearerps1statistics
Parameters:1~64 ZeroormoreERPSgroupnumbers
statisticsClearERPSstatistics
Example:
SISPM1040‐3248‐L#clearerps1statistics
SISPM1040‐3248‐L#

Command:evc
Description: ClearEthernetVirtualConnectionsstatistics.
Syntax: clearevcstatistics{[<evc_id>|all]}[ece[<ece_id>]][interface(<port_type>[<port_list>])
][class<cosid>][pw<pw_num_list>]
Parameters:<1‐454>EVCidentifier
class SelectClassofServiceID
interfaceInterface
pw ClearEVCstatisticsforattachedMPLS‐TPPseudo‐Wires
<cr>
Example:
SISPM1040‐3248‐L#clearevcstatistics1pw1
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 13 of 250
Command:ip
Description: ClearIPv4protocolparameters.
Syntax: 
clearipacd
cleariparp
clearipdhcpdetailedstatistics{server|client|snooping|relay|helper|all}[interface(<port_type>[
<in_port_list>])]
clearipdhcprelaystatistics
clearipdhcpserverbinding<ip>
clearipdhcpserverbindingtype{automatic|manual|expired}
clearipdhcpserverstatistics
clearipdhcpsnoopingstatistics[interface(<port_type>[<in_port_list>])]
clearipigmpsnooping[vlan<v_vlan_list>]statistics
clearipospfprocess
clearipstatistics
Parameters:acd AddressConflictDetection
arp ClearARPcache
dhcp DynamicHostConfigurationProtocol
igmp InternetGroupManagementProtocol
ospf OpenShortestPathFirst(OSPF)
statistics Trafficstatistics
Example:
SISPM1040‐3248‐L#clearipstatistics
SISPM1040‐3248‐L#clearipigmpsnoopingstatistics
SISPM1040‐3248‐L#

Command:ipv6
Description: ClearIPv6configurationparameters.
Syntax: clearipv6mldsnooping[vlan<v_vlan_list>]statistics
clearipv6neighbors
clearipv6statistics
Parameters:mld MulticastListenerDiscovery
neighborsIPv6neighbors
statistics Trafficstatistics
Example:
SISPM1040‐3248‐L#clearipv6statistics
SISPM1040‐3248‐L#clearipv6mldsnoopingstatistics
SISPM1040‐3248‐L#clearipv6mldsnoopingvlan100statistics
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 14 of 250
Command:lacp
Description: ClearLACPstatistics.
Syntax: clearlacpstatistics
Parameters:statisticsClearallLACPstatistics
<cr>
Example:
SISPM1040‐3248‐L#clearlacpstatistics
SISPM1040‐3248‐L#

Command:link‐oam
Description: ClearLinkOAMstatisticonaspecificinterfaceorallinterfaces.
Syntax: clearlink‐oamstatistics[interface(<port_type>[<plist>])]
Parameters:interface  ClearLinkOAMstatisticonaspecificinterfaceorallinterfaces.
*   AllswitchesorAllports
GigabitEthernet 1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
<port_type_list> Portlistin1/1‐28
* AllswitchesorAllports
GigabitEthernet 1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
<cr>
Example:
SISPM1040‐3248‐L#clearlink‐oamstatisticsinterfaceGigabitEthernet1/4
SISPM1040‐3248‐L#

Command:lldp
Description: ClearLLDPstatistics.
Syntax: clearlldpstatistics{[interface(<port_type>[<plist>])]|global}
Parameters:statisticsClearsLLDPstatistics.
lldp ClearsLLDPstatistics.
|  Outputmodifiers
global Clearglobalcounters
interface Interfacekeyword.
<cr>
Example:
SISPM1040‐3248‐L#clearlldpstatistics
SISPM1040‐3248‐L#clearlldpstatisticsinterface*
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 15 of 250
Command:logging
Description: ClearSystemloggingmessages.
Syntax:clearlogging[info][warning][error][emerg][alert][crit][notice][debug][switch
<switch_list>]
Parameters:alert  Severity1:Actionmustbetakenimmediately
crit Severity2:Criticalconditions
debug Severity7:Debug‐levelmessages
emerg Severity0:Systemisunusable
error Severity3:Errorconditions
info Severity6:Informationalmessages
notice Severity5:Normalbutsignificantcondition
warningSeverity4:Warningconditions
<cr>
Example:
SISPM1040‐3248‐L#clearloggingdebuginfo
SISPM1040‐3248‐L#clearloggingdebuginfonotice
SISPM1040‐3248‐L#

Command:mac
Description: FlushMACAddresstable.
Syntax: clearmacaddress‐table
Parameters:None
Example:
SISPM1040‐3248‐L#clearmacaddress‐table
SISPM1040‐3248‐L#

Command:mep
Description: ClearMaintenanceEntityendPoint.
Syntax: clearmep<inst>{lm[both|tx|rx]|dm|lb|tst|bfd}
Parameters:<uint> TheMEPinstance.
dm  ClearDMmeasuringinformation.
lb  ClearLBmeasuringinformation.
lm ClearLMmeasuringinformation.
tst ClearTSTmeasuringinformation.
Example:
SISPM1040‐3248‐L#clearmep1dm
SISPM1040‐3248‐L#clearmep1tst
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 16 of 250
Command:mvr
Description: ClearMulticastVLANRegistrationconfiguration.
Syntax: clearmvr[vlan<v_vlan_list>|name<mvr_name>]statistics
Parameters:name MVRmulticastname
statisticsRunningMVRprotocolcounters
vlan MVRmulticastVLAN
Example:
SISPM1040‐3248‐L#clearmvrstatistics
SISPM1040‐3248‐L#clearmvrvlan100statistics
SISPM1040‐3248‐L

Command:port‐security
Description: Clearportsecurity.Youcanalsoconfigureaspecificinterface.SeeInterfaceConfigCommands.
Syntax: clearport‐securitysticky{All|interface(<port_type>[<plist>])}
clearport‐securitydynamic[{address<mac>[vlan<vlan_on_mac>]}|{interface(<port_type>[<plist>])[
vlan<vlan_on_interface>]}|vlan<vlan>]
Parameters:dynamicDynamicentries
sticky portsecuritystickyfunction.
addressClearaspecific(VLAN,MAC)tuple
interface Portinterface
vlanDeleteallMACaddressesonagivenVLAN
<cr>
Example:
SISPM1040‐3248‐L#clearport‐securitydynamicaddress11‐22‐33‐44‐55‐66
SISPM1040‐3248‐L#clearport‐securitysticky?
Allclearallstickymacatallports
interfaceChooseport
SISPM1040‐3248‐L#clearport‐securitystickyAll

Command:ptp
Description: ClearPTPservoforaPrecisionTimingProtocol(PTPv2)clockinstance.
Syntax: clearptp<clockinst>servo
Parameters:<0‐3>
servo
<cr>
Example:
SISPM1040‐3248‐L#clearptp0servo
SISPM1040‐3248‐L#
Messages:Clockinstance0:doesnotexist
%%Failedtosetnetwork‐clockconfiguration.
%(MESA:Unknownerrorcode)

TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 17 of 250
Command:sflow
Description: Clearsflowstatistics.
Syntax: clearsflowstatistics{receiver[<receiver_index_list>]|samplers[interface[<samplers_list>](
<port_type>[<v_port_type_list>])]}
Parameters: receiverClearstatisticsforreceiver.
samplersClearstatisticsforsamplers.
interfaceClearstatisticsforaspecificinterfaceorinterfaces.
<cr>
Example:
SISPM1040‐3248‐L#clearsflowstatisticsreceiver
SISPM1040‐3248‐L#clearsflowstatisticssampler?
interfaceClearstatisticsforaspecificinterfaceorinterfaces.
<cr>
SISPM1040‐3248‐L#clearsflowstatisticssampler
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 18 of 250
Command:spanning‐tree
Description: Clearspanningtreeparameters.
Syntax: clearspanning‐tree{{statistics[interface(<port_type>[<v_port_type_list>])]}|{
detected‐protocols[interface(<port_type>[<v_port_type_list_1>])]}}
Parameters: detected‐protocolsSettheSTPmigrationcheck
statisticsSTPstatistics
interface  Chooseport
<cr>
* AllswitchesorAllports
GigabitEthernet1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
Example:
SISPM1040‐3248‐L#clearspanning‐treestatistics
SISPM1040‐3248‐L#clearspanning‐treedetected‐protocols
SISPM1040‐3248‐L#

Command:statistics
Description: Clearstatisticsforoneormoregiveninterfaces.
Syntax: clearstatistics[interface](<port_type>[<v_port_type_list>])
Parameters: *  AllswitchesorAllports
GigabitEthernet1GigabitEthernetPort
10GigabitEthernet10GigabitEthernetPort
interfaceInterface
<port_type_list> Portlistin1/1‐28
<port_type_list> Portlistin1/1‐4
Example:
SISPM1040‐3248‐L#clearstatisticsinterfaceGigabitEthernet1/9
SISPM1040‐3248‐L#

Command:system
Description: ClearsystemLEDstatus.
Syntax:clearsystemledstatus[switch<switch_list>]{fatal|software|post|ztp|stack‐firmware|all}
Parameters:allClearallerrorstatusofthesystemLEDandbacktonormalindication
fatalClearfatalerrorstatusofthesystemLED
softwareCleargenericsoftwareerrorstatusofthesystemLED
Example:
SISPM1040‐3248‐L#clearsystemledstatussoftware
SISPM1040‐3248‐L#clearsystemledstatusfatal
SISPM1040‐3248‐L#clearsystemledstatusall
SISPM1040‐3248‐L#


TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 19 of 250
Chapter5–ConfigModeCommands
Table:ConfigModeCommands
Command Description
aaa  Authentication,AuthorizationandAccounting
access Accessmanagement
access‐list Accesslist
aggregation Aggregationmode
banner  Defineabanner
clock Configuretime‐of‐dayclock
debug Debuggingfunctions
defaultSetacommandtoitsdefaults
dms EnableDMSMaster
do Torunexeccommandsintheconfigurationmode
dot1x IEEEStandardforport‐basedNetworkAccessControl
enable Modifyenablepasswordparameters
end GobacktoEXECmode
eps EthernetProtectionSwitching
erps EthernetRingProtectionSwitching
event Trapeventseveritylevel
exit Exitfromcurrentmode
green‐ethernet GreenEthernet(Powerreduction)
gvrp EnableGVRPfeature
help Descriptionoftheinteractivehelpsystem
hostname Setsystem'snetworkname
interface Selectaninterfacetoconfigure
ip InterfaceInternetProtocolconfigurationcommands
ipmc IPv4/IPv6multicastconfiguration
ipv6 IPv6configurationcommands
json JavaScriptObjectNotationRPC
lacp LACPsettings
lineConfigureaterminalline
lldp LinkLayerDiscoverProtocol.
logging Systemloggingmessage
loop‐protect Loopprotectionconfiguration
mac MACtableentries/configuration
map‐api‐key Setgooglemapkeystring
mepMaintenanceEntityPoint
monitorMonitoringdifferentsystemevents
mvr MulticastVLANRegistrationconfiguration
mvrp EnableMVRPfeatureglobally
network‐clock network‐clock
no Negateacommandorsetitsdefaults
ntp ConfigureNTP

TransitionNetworks SISPM1040‐3248‐LCLIReference
33764 Rev. A https://www.transition.com Page 20 of 250
poePowerOverEthernet.
port‐securityThiscommandisobsolete/Changed
privilegeCommandprivilegeparameters
prompt Setprompt
ptp PrecisiontimeProtocol(1588)
qos QualityofService
radius‐server ConfigureRADIUS
rmonRemoteMonitoring
router Routingprocess
sflow Statisticsflow.
smtp Setemailinformation
snmp‐server SetSNMPserver'sconfigurations
spanning‐tree SpanningTreeprotocol
svl SharedVLANLearning
switchport SetVLANswitchingmodecharacteristics
system SettheSNMPserver'sconfigurations
tacacs‐serverConfigureTACACS+
udld EnableUDLDinaggressiveornormalmodeandsetconfigurablemessagetimeronall
fiber‐opticports.
upnp SetUPnPconfiguration
username EstablishUserNameAuthentication
vlan VLANcommands
voice Voiceapplianceattributes
webWeb



