TransLite TL-9802 User manual

P a g e | 1
PRODUCT MODEL NUMBER: TL-9802
G.hn COAXIAL ETHERNET BRIDGE
DISCLAIMER
No part of this document may be reproduced in any form without the written permission of the copyright owner.
The contents of this document are subject to revision without notice due to continued progress in methodology,
design and manufacturing. TRANSLITE GLOBAL LLC shall have no liability for any error or damage of any kind
resulting from the use of this document.
COPY WARNING
This document includes some confidential information. Its usage is limited to the owners of the product
that it is relevant to. It cannot be copied, modified, or translated in another language without prior written
authorization from TRANSLITE GLOBAL LLC.

P a g e | 2
PRODUCT OVERVIEW
TL-9802 is a coaxial ethernet bridge that uses the G.hn technology and
allows you to get data rates up to 2Gbps* over coaxial cable lines and
IPTV transmission. It provides an affordable solution by making use of the
existing coaxial cables that are already installed throughout many homes
and businesses, to create a high-performance network connection that is
both secure and reliable.
It enables you to connect various multimedia devices like smart TV,
consoles, computers, printers, etc., simultaneously to the network without
interference for a seamless high-speed connection for streaming in HD,
online gaming, downloading large files and much more. The data is kept
highly secure and reliable with the 128-bit Advanced Encryption Standard
(AES) encryption. A maximum of 16 devices can be connected in a
network group.
KEY FEATURES
➢Delivers high-speed Internet access through your existing coaxial wires.
➢G.hn-compliant, ITU-T G.9960-compliant
➢Up to 2Gbps (PHY rate) ultra-high-speed coaxial network
➢Features 2 * GbE port
➢Optional (for operators):
oTR-069/TR-181 remote management - QoS support
➢G.hn, ITU-T G.9960/9961/9962/9963/9964 compliant

P a g e | 3
➢G.hn frequency band: 2-200MHz*
➢PHY rate: up to 2Gbps
➢Support for home networking connectivity
➢G.hn LED*1, Ethernet LED*1, PWR LED*1
➢RJ-45 GbE Port (Yellow) * 2
➢Coaxial 75ohm F-type connector * 2
➢One F-type connector for TV pass-through
➢Diplexers (LP&HP) can be customized.
* (For satellite /TV signals frequency, it can be tuned up to 3GHz upon
request.)

P a g e | 4
SPECIFICATIONS
General Information
Model No.
TL-9802 G.hn over coax Ethernet Bridge
Main Function
G.hn Coaxial Bridge
GbE LAN port * 2
F-type connector* 2
LP + HP diplexer Built-in
Product Size
130 x 80 x 25 mm
Features
Main chipset
88LX5153
Installation
Desk-top
Adaptor
Plug type
AC/DC Adaptor DC Jack in
LAN Standards
IEEE 802.3i (10 BASE-T),
IEEE 802.3u (100 BASE-TX),
IEEE 802.3ab (1000 BASE-T)
LAN port
2 X GbE (Pantone Color: 114c or 109c)
Coaxial Connector
F-type

P a g e | 5
Input voltage
DC 12 V / 1A
Frequency Band
G.hn Coaxial 200MHz
Hi-Pass Filter: 258 ~ 2000MHz
PLC protocol
G.hn ITU-T G.9960
G.hn ITU-T G.9961
G.hn ITU-T G.9962
G.hn ITU-T G.9963
G.hn ITU-T G.9964
ITU-T G.9972
MAC Access
Methods
CSMA/CA, TDMA and CSMA
Group/Pairing
Press and hold paring button for 3 seconds to enter into paring mode
Un-pair: press and hold paring button for 5 seconds to un-pair
RESET
Press and hold for 10 seconds
LED
Power, G.hn, Ethernet
HGF
Compliant
MTBF
System: 300,000hrs (follow “Telcordia SR-322 Issue 3”)
Lifetime
Over 10,000 hours
HW SGMII interface
Auto
Access Methods
CSMA/CA, TDMA medium access protocols
Modulation
1024/512/256/128/64/32/16/ 8-QAM, QPSK, BPSK
Max. devices in a
network Group
16 for HN
Encryption
AES 128-bit encryption
IGMP Snooping
Supports IPv4 IGMP snooping and Ipv6 MLD.
TR-069
N/ A
Mechanical
Color
White
Adaptor
AC/DC Adaptor DC Jack in (DC12V/1A)
2.5mm
Pair button
X1
RESET button
X1
Giga RJ45 port
2-port
RJ 45 port
X2
LED
(Power, G.hn, Ethernet)
LED symbol
Power, G.hn, Ethernet
Housing print
1.G.hn-Link
2. TV

P a g e | 6
3. Reset
4. GETH-2
5. GETH-1
6. Power
7. Pair
Regulation
FCC, ICES report
Compliant
CE-EMC, CE-LVD
report
Compliant
ROHS
Compliant
WEEE
Compliant
HGF
Compliant
Temperature
Operating: -10 ~ 40C
Storage: -20 ~ 70C
Relative Humidity
Operating: 10~85% Non-Condensing
Storage: 5~90% Non-Condensing
HARDWARE INSTALLATION

P a g e | 7
Step 1: Plug a Coaxial Bridge into an AC outlet using the AC adapter
provided. Use a coaxial cable to connect its F-connector to a wall’s
coaxial connector. Then use an Ethernet cable to connect the Bridge to
a router or modem.
Step 2: Plug another Coaxial Bridge into another AC outlet using the AC
adapter provided. Use a coaxial cable to connect its F-connector to the
wall’s coaxial connector. Then use an Ethernet cable to connect it to any
network device such as a streaming box, smart TV, or gaming console.
PAIRING TWO BRIDGES
Users can easily create a G.hn network—simply press the Pairing buttons
on the Bridges in the proper order to “pair” them together. To set up the
network, follow the steps below

P a g e | 8
Step 1: Verify the Power LED initial state on both Bridges is solid green.
The G.hn Link LED is off when a TL-9802 Coaxial Bridge does not have a
secured link to a G.hn network.
Step 2: Press and hold the Pairing button on Bridge A for 3 seconds (refer
to the image above) until its G.hn Link LED starts blinking amber.
Step 3: Press and hold the Pairing button on Bridge B for 3 seconds until its
G.hn Link LED starts blinking amber.
Step 4: When a Bridge has paired to a network, its G.hn Link LED will be
solid amber.
Note: The G.hn LED of Bridge A will continue to blink for approx. 120
seconds. During that time, you may add more bridges to the network by
repeating Steps 1–4 above.
UNPAIRING/REMOVING A DEVICE FROM THE G.hn
NETWORK
Step 1: Press and hold the Reset button (inside the pinhole) of the unit for
5 seconds until all its LEDs turn off for 0.5 seconds and then turn back on.
Step 2: The G.hn Link LED will then blink once in amber, then turn off.

P a g e | 9
APPENDIX
LED BEHAVIOUR
LED
Power LED
Green + Red
Green ON: Power on and ready, can link to other G.hn over Coax
device in unsecured mode.
Amber BLINKING: During Security pairing procedure. In this
procedure, the device joining or being joined into same logical
network will continue 120 seconds blinking, until the procedure
succeeds or is canceled.
Amber SOLID: Device is paired into a G.hn over Coax link network.
OFF: Power off.
G.hn Link LED
Green + Red
Green SOLID: G.hn over Coax link PHY rate is above 300Mbps and no
data traffic in Coax cable.
Green BLINKING: G.hn over Coax link PHY rate is above 300Mbps
(Should be changed for specific application)
Amber SOLID: G.hn over Coax link PHY rate is between in below
300Mbps and above 100 Mbps and no data traffic in Coax cable.
Amber BLINKING: G.hn over Coax link PHY rate is between in below
300Mbps and above 100 Mbps.
Red SOLID: G.hn over Coax link PHY rate is below 100Mbps and no
data traffic in Coax cable.
Red BLINKING: G.hn over Coax link PHY rate is below 100Mbps
(Should be changed for specific application)
OFF: G.hn over Coax Link not detected (either another device in
same network is too far to communicate, or it is alone in its logical
network).
Ethernet LED
Green + Red
Green SOLID: Port2 Ethernet link detected.
Green BLINKING: When Port2 Ethernet link is active
Red SOLID: Port1 Ethernet link detected.
Red BLINKING: When Port1 Ethernet link is active.
OFF: No Ethernet link detected.

P a g e | 10
PUSH BUTTON BEHAVIOUR
Buttons
Security
Pairing of two units to establish a network
Step 1: Initial state Power LED is solid green.
Step 2: Press and hold Pair Button (3 secs) of unit A until Power LED
starts blinking in Amber.
Step 3: Press and hold Pair Button (3 secs) of unit B until Power LED
starts blinking in Amber.
Step 4:
The Power LED of the two units should be solid Amber.
Note:
The Power LED of unit A shall continue to blink for ~120 second.
During that time, it is possible to add more new devices into the
network by repeating step 3 and step 4.
Reset
(inside the needle
pin hole)
Removing a device from a secured network (Un-Pairing)
Step 1: Press and hold Reset Button (pin hole) of the unit for 10
seconds until all LEDs blinks once. (Turn off for 1 seconds and then
turn on)
Step 2: The Power LED of the unit should be solid green and the G.hn
link LEDs should be off. (May take 2 seconds after the above blink)