ADTRAN Total Access 544R User manual

TOTAL ACCESS 544R P/N 4200704L8, L9, L10, L11
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 61200704L2-13A, April 2003 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2003 ADTRAN, All Rights Reserved
Connecting to the Total Access 544R
Connecting a VT100 terminal (or VT100 terminal emulator) to the CRAFT
interface (on the back panel of the unit) allows access to the terminal
menus and management features of the Total Access 544R.
Perform Steps Below in the Order Listed:
1. Configure a VT100 terminal (or terminal emulation software) with the
following settings:
If the terminal has a parallel setting, disable it and use serial.
2. Connect one end of the 6” data cable (supplied) into the Total Access
544R CRAFT port. (This connection is RJ-45.) Make the connection to
the VT100 terminal as appropriate for your connection. ADTRAN
supplies an RJ-45 to DB-9 adapter for connections to standard DB-9
Communications (COM) ports.
3. Initiate a terminal session and the LOGIN screen displays. Press Enter
to enter the menu. There is not a manufacturer’s password by default.
(Passwords in the Total Access 544R are case sensitive.)
Data Rate: 9600 baud Stop Bits: 1
Data Bits: 8 Flow Control: None
Parity Bits: None
LAN WAN
LAN LEDs WAN LEDs Power LED
Front Panel LEDs
The front panel provides five status LEDs to monitor operation and activity. The
following table provides LED activity explanations.
LED COLOR DESCRIPTION
LAN TX/RX
Off There is no data trafic on the LAN
Green (blinking) There is data trafic on the LAN
LAN LINK
Off The physical link is down; there is no Ethernet connection
Green (solid) There is link integrity on the LAN (physical link is up)
WAN STAT
Red (solid) SHDSL is down
Green (solid) SHDSL is up
WAN ERR Off Not applicable
PWR
Green (solid) Power is supplied to the unit
Off Power is not supplied to the unit
Reviewing the Front Panel

TOTAL ACCESS 544R P/N 4200704L8, L9, L10, L11
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 61200704L2-13A, April 2003 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2003 ADTRAN, All Rights Reserved
Network
Interface
10/100BaseT
Ethernet
Craft
Interface
AC Power Connection
R
ev
i
ew
i
ng
th
e
R
ear
P
ane
l
D
es
i
gn
Network Pinout
Craft Pinout
PIN NAME DESCRIPTION
1R1 RXDATA-RING Receive data from the network
2T1 RXDATA-TIP Receive data from the network
3—UNUSED —
4RTXDATA-RING Transmite data from the network
5TTXDATA-TIP Transmite data from the network
6—UNUSED —
PIN NAME DESCRIPTION
1 GND Ground - connected to unit chassis
2 RTS Request to send - flow control
3 RXDATA Data received by the Total Access 544R
4 DTR Data terminal ready
5 TXDATA Data transmitted by the Total Access 544R
6 CD Carrier detect
7 UNUSED —
8 CTS Clear to send - flow control
Equipment Dimensions
The Total Access 544R measures 11.25” W, 7.5” D, and 2” H and comes equipped
for table top or wall mount use.
Power Requirements
The Total Access 544R has a maximum power consumption of 100-250VAC
50/60Hz and a maximum current draw of 300 mA.
For direct contact call:
1-800-726-8663
1-256-963-8716
10/100BaseT Ethernet Pinout
PIN NAME DESCRIPTION
1 TX1 Transmit Positive
2 TX2 Transmit Negative
3 RX1 Receive Positive
4,5, 7, 8 — Unused
6 RX2 Receive Negative