Transmitter Solutions iCE?Entry?100 User manual

iCE$Entry$100+
COMPACT'MULTI+APARTMENT'GSM'DOOR'ENTRY'UNIT'
'
+
INSTALLATION+MANUAL+
+

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%2%
Contents
1%FOR YOUR SAFETY.......................................................................................... 6%
2%INTRODUCTION............................................................................................... 7%
3%FEATURES AND APPLICATIONS ........................................................................ 8%
4%START UP...................................................................................................... 9%
5%LED DISPLAY ................................................................................................10%
6%CLEAR ALL PROGRAMMED DATA FROM SIM ......................................................11%
7%CONNECTING DIAGRAM ..................................................................................12%
8%PROGRAMMING ICE-ENTRY-100 .......................................................................13%
9%THE ICE-ENTRY-100 PARAMETERS...................................................................14%
9.1%ALARM SUPPORT .................................................................................................................................. 14%
9.2%OUTPUT MANAGEMENT ........................................................................................................................ 18%
9.3%SECURITY LEVEL -SL ........................................................................................................................... 20%
9.4%PREPAID CARD CREDIT AND VALIDITY INFORMATION .......................................................................... 22%
9.5%SET-UP PARAMETERS ........................................................................................................................... 24%
9.6%SMS MESSAGES EDITOR........................................................................................................................ 28%
9.7%INTERCOM............................................................................................................................................. 29%
9.8%TRADE BUTTON (OPTION).................................................................................................................... 31%
9.9%DIRECT ACCESS BY ENTERING PIN CODE .............................................................................................. 32%
9.10%CLIP .................................................................................................................................................... 33%
9.11%EVENT LOGING ................................................................................................................................... 36%
9.12%SPECIAL SMS COMMANDS .................................................................................................................. 37%
10%PRINT-OUT OF THE PARAMETERS ..................................................................39%
10.1%RECEIVE ALL PARAMETERS (PALL).................................................................................................... 39%
10.2%CHECK SW REVISION (PSW) ............................................................................................................... 39%
10.3%CHECK SIGNAL QUALITY (PSQ) .......................................................................................................... 39%
10.4%RECEIVE TELEPHONE NUMBERS (PTN) ............................................................................................... 39%
10.5%RECEIVE LINKS (PLN) ......................................................................................................................... 39%
10.6%RECEIVE INPUT PARAMETERS (PIN).................................................................................................... 40%
10.7%RECEIVE INPUT FILTER VALUE (PID)................................................................................................... 40%
10.8%RECEIVE OUTPUT FILTER VALUE (POD) ............................................................................................. 40%
10.9%RECEIVE DELAY BEFORE DIAL VALUE (PDD)...................................................................................... 40%
10.10%RECEIVE ACCESS TELEPHONE NUMBERS (PSL) .................................................................................. 40%
10.11%RECEIVE OUTPUT PARAMETERS (POS) ............................................................................................... 40%
10.12%RECEIVE ALL PROGRAMMED SMS MESSAGES (P#) ............................................................................. 41%

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%3%
10.13%RECEIVE SET UP PARAMETERS VALUE (PPA) ..................................................................................... 41%
10.14%RECEIVE CREDIT PARS PARAMETERS (PCREF) .................................................................................... 41%
10.15%RECEIVE ALL CLIP PARAMETERS (PCLP) ............................................................................................ 41%
10.16%RECEIVE INTERCOM CALL GROUPS PARAMATERS............................................................................ 42%
10.17%RECEIVE TRADE BUTTON PARAMETERS ............................................................................................. 42%
10.18%STATE OF THE CREDIT FOR THE PREPAID CARD ................................................................................ 42%
10.19%STATE OF THE OUTPUTS (PORC) ....................................................................................................... 42%
10.20%MANUAL GSM MODULE RETARD (MRES) ............................................................................................ 43%
10.21%RECEIVE STATUS OF INPUTS (INS) ..................................................................................................... 43%
10.22%RECEIVE ICE-ENTRY-100 LOG............................................................................................................. 43%
11%CHANGING PARAMETERS USING THE SMS COMMANDS......................................44%
12%DEFAULT SETTINGS ON ICE-ENTRY-100 .........................................................46%
13%PARAMETERS PRINT-OUT COMMANDS ............................................................48%
14%TECHNICAL SPECIFICATIONS.........................................................................49%

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%4%
Figures
Figure 1: ICE-ENTRY-100 Connection diagram .......................................................12%
Figure 2: Input Connection diagram. ......................................................................14%
Figure 3: Output Connection diagram ....................................................................19%

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%5%
Tables
Table 1: IN, ID and DD parameters .........................................................................15!
Table 2: IN, ID, DD parameters example.................................................................15!
Table 3: Remote alarm reporting parameters.........................................................17!
Table 4: Remote alarm reporting example ............................................................17!
Table 5: DTMF control example..............................................................................18!
Table 6: Output management parameters .............................................................19!
Table 7: Output management parameters example ...............................................20!
Table 8: SL parameter............................................................................................21!
Table 9: SL example ...............................................................................................21!
Table 10: Prepaid card validity parameters............................................................23!
Table 11: Credit example .......................................................................................23!
Table 12: Set-up parameters. ................................................................................26!
Table 13: Set-up parameters example. ..................................................................27!
Table 14: Message parameters. .............................................................................28!
Table 15: Message parameters example. ...............................................................29!
Table 16: Intercom parameters..............................................................................30!
Table 17: Intercom parameters example................................................................30!
Table 18: Trade button parameters. ......................................................................31!
Table 19: Trade button example............................................................................32!
Table 20: Entering PIN code parameters................................................................33!
Table 21: Entering PIN code example.....................................................................33!
Table 22: CLIP parameters. ....................................................................................34!
Table 23: CLIP parameters example. ......................................................................35!
Table 24: LOG parameters. ....................................................................................36!
Table 25: LOG parameters example. ......................................................................37!
Table 26: SMS commands. .....................................................................................38!
Table 27: SMS commands example. .......................................................................38!
Table 28: ICE-ENTRY-100 default settings.............................................................47!
Table 29: ICE-ENTRY-100 parameters print out commands. .................................48!

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%6%
1 FOR YOUR SAFETY
Read these simple guidelines. Not following them may be dangerous or illegal. Read
the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the unit on when use of wireless phone is prohibited or when it may
cause interference or danger.
INTERFERENCE
All wireless phones and units may be susceptible to interference, which could
affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the unit off near medical equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in aircraft.
SWITCH OFF WHEN REFUELING
Do not use the unit at a refueling point. Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the unit where blasting is in progress.
USE SENSIBLY
Use only in the normal position as explained in the product documentation. Do not
touch the antenna unnecessarily.

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%7%
2 INTRODUCTION
ICE-ENTRY-100 is a simple GSM intercom communication system that is designed
to ensure low-cost, reliable and single box solution for intercom application. It is
designed for unlimited range, wire free GSM intercom and CLIP support.
In addition ICE-ENTRY-100 supports alarm detection, stay-alive messages, credit
detection etc…

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%8%
3 FEATURES AND APPLICATIONS
Features:
⇒Built-in 2 or 4 band GSM module
⇒Keypad call support
⇒Keypad PIN enter support
⇒2 alarm inputs
⇒2 outputs ( relay supported )
⇒Up to 100 telephone numbers for CLIP support
⇒Programming by USB SIM Key editor
⇒Download programming by SMS command
⇒Anti-tampering input
Applications:
⇒Single box, wire free intercom solution
⇒Remote gate opener (CLIP)
⇒Simple alarm support

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%9%
4 START UP
VERY
IMPORTANT
USE A MICRO SIM CARD (micro-SIM, see the picture)
WITH MEMORY FOR UP TO 250 CONTACTS!
⇒Insert SIM card to be used for ICE-ENTRY-100 in your personal mobile phone.
IMPORTANT
ERASE THE PIN CODE!
⇒Insert SIM card in ICE-ENTRY-100 device. The unit must be switched OFF
when you insert the SIM!
⇒Connect inputs and outputs to ICE-ENTRY-100.
⇒Connect the antenna to antenna connector.
⇒Connect power cable to ICE-ENTRY-100 device
⇒Connect device to source power supply voltage.
⇒Wait until LED3 display is turned ON (green) and LED1 (blue) starts flashing.
This is set in around 1 minute.
⇒ICE-ENTRY-100 unit is now ready to operate.
IMPORTANT
Before sending any SMS commands to ICE-ENTRY-100 device,
ICE-ENTRY-100 must be in normal operation!
NOTE
ICE-ENTRY-100 device will “beep” in 15s interval until the device is not
in normal operation.

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%10%
5 LED DISPLAY
GREEN LED (LED1)
- Indicates the level of the GSM signal from 1 to 5 LED flashes (1 is weak
signal, 5 is excellent signal)
Red LED (LED2)
- When LED 2 is ON the unit has a problem with a GSM network connection or
the GSM part of the unit is out of order. In this case immediately call the
service!
Yellow LED (LED3)
- Short flashing indicates that the GSM module is ON, but it is not yet
connected on the GSM network. After connection, yellow led is flashing with
short pulse ON and a long pulse OFF.

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%11%
6 CLEAR ALL PROGRAMMED DATA FROM SIM
This is highly recommended when a SIM card you are going to use for the ICE-
ENTRY-100 is not new and it already has some data stored in the phone book
memory.
By sending this SMS to ICE-ENTRY-100 all programmed parameters and numbers
are cleared:
;SDCLR;
After sending SMS you should wait at least 30 second for the command to be
executed!
NOTE
By sending this command to the ICE-ENTRY-100 all programmed data
are erased from the SIM card!

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%12%
7 CONNECTING DIAGRAM
Before connection the ICE-ENTRY-100 please take a look at connection diagram.
Figure 1: ICE-ENTRY-100 Connection diagram

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%13%
8 PROGRAMMING ICE-ENTRY-100
ICE-ENTRY-100 device supports different types of programming:
⇒To program ICE-ENTRY-100 parameters put the SIM card into your personal
GSM phone. Add programming parameters in SIM Card “Phone Book”.
⇒You can program ICE-ENTRY-100 remotely by SMS command.
⇒You can program ICE-ENTRY-100 with USB key and SIM manager.

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%14%
9 THE ICE-ENTRY-100 PARAMETERS
To support versatile functionality of ICE-ENTRY-100 different parameters are used.
The parameters are divided in logical sections and are described in the following
chapters.
9.1 ALARM SUPPORT
Alarm reporting is supported by group of different parameters. First section is
used to define the relations needed for alarm to be trigged. The second section is
used to report alarm.
9.1.1 ALARM TRIGGERING
Parameters are used to control (filter) the triggering of the alarm inputs.
9.1.1.1 IN parameter
Alarm input can be on only used as normal open (N.O.) triggered with GND. When
you need the input feedback information it is possible to receive SMS when input
returns from alarm to normal position. To receive the return SMS use IN setting 4.
⇒IN = 0 – Normal Open – triggered with negative voltage (GND)
⇒IN = 4 = IN = 0 + input reset SMS
Figure 2: Input Connection diagram.

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%15%
9.1.1.2 ID parameter
ID parameter determines time period of the pulse length to trigger the alarm. The
pulse time can be from 0,5 seconds to 9999 seconds. The default time is 0,5
seconds when the parameter value is 0.
9.1.1.3 DD parameter
This parameter is used to define the delay between the time that alarm input is
trigged and the time that alarm is reported.
9.1.1.4 Table of parameters
Name
Comment
IN1
Mode of operation for input 1
IN2
Mode of operation for input 2
ID1
Input time integration delay on input 1
ID2
Input time integration delay on input 2
DD1
Time delay for alarm reporting on input 1
DD2
Time delay for alarm reporting on input 2
Table 1: IN, ID and DD parameters
Example:
♦Direct programming on the SIM card
ICE-ENTRY-100 PROGRAMMING TABLE
SIM CARD PHONE BOOK
Name
Number
Description
IN1
0
Alarm activated by connecting to GND
IN2
4
Alarm activated by connecting to GND + RST
SMS
ID1
10
Input 1 has to be valid for 10second to trigger
the alarm
ID2
0
Input 2 has to be valid for 0,5 second to trigger
the alarm
DD1
0
Reporting of the alarm on input 1 is delayed by
0s
DD2
15
Reporting of the alarm on input 1 is delayed by
15s
Table 2: IN, ID, DD parameters example

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%16%
♦Remote programming by SMS
;IN1=0;IN2=4;ID1=10;ID2=0;DD1=0;DD2=15;
9.1.2 REMOTE REPORTING ALARM EVENTS
Parameters used to define the way to report the alarm event.
NOTE
ICE-ENTRY-100 device send SMS messages for reporting alarm events.
9.1.2.1 TN parameter
Telephone numbers for remote alarm reporting are listed as TN parameters.
Remote alarm reporting on ICE-ENTRY-100 is done via SMS messages.
9.1.2.2 LN parameter
This parameter is used to link alarm event from inputs or any other source to the
telephone numbers from TN list.
9.1.2.3 LOT parameter
LOT parameter is used to define the time control for voice calls. The start of voice
connection starts the LOT timer. If the voice connection is still ON when the LOT
timer expires ICE-ENTRY-100 disconnects voice connection.
9.1.2.4 Table of parameters
Name
Comment
TN1
1st telephone number
TN2
2nd telephone number
TN3
3rd telephone number
TN4
4th telephone number
TN5
5th telephone number
LN1
Input & telephone No. linking for 1st alarm input (TN1 –

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%17%
TN5)
LN2
Input & telephone No. linking for 2nd alarm input (TN1
–TN5)
LN3
Periodic test SMS. No. linking (TN1 –TN5)
LN4
SIM card refill. No. linking (TN1 –TN5)
LN5
NAC list. No. linking (TN1 –TN5)( see note)
LN6
Log status. No. linking (TN1 –TN5)
LOT
Time out for GSM connection.
Table 3: Remote alarm reporting parameters
Note:
When telephone number (calling or messaging ICE-ENTRY-100) is not on the CLIP
list, not acknowledge event occurs (NAC). The telephone number responsible for
this event can be send to TN user for notification.
Example:
♦Direct programming on the SIM card
ICE-ENTRY-100 PROGRAMMING TABLE
SIM CARD PHONE BOOK
Name
Number
Description
TN1
042376678
1st telephone number
LN1
13
Input 1 reports alarm to TN1 & TN3
LN2
1234
Input 2 reports alarm to TN1 & TN2 & TN3 &
TN4
LN5
1
NAC event sent to TN1
LOT
60
Voice connection stay valid for max of 60s,
after this time
Voice connection breaks
Table 4: Remote alarm reporting example
♦Remote programming by SMS
;TN1=042376678;LN1=13;LN2=1234;LN5=1;LOT=60;

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%18%
9.1.3 CONTROLING OUTPUTS WITH DTMF
ICE-ENTRY-100 can control the outputs with the use of DTMF. This is very useful
function in the intercom application.
To control the outputs the user must press the combination of 2 digits. First digit
is used to select the output (1 to 2), the second digit is used to activate (1) or
deactivate (0) the output. There is a special case when the user can select for
first digit (output selection) number 0. In this case all outputs control by the same
time.
Combination must be pressed in 2s interval, and must be 3s apart to be valid.
NOTE
ICE-ENTRY-100 must be in voice connection to support DTMF output
control!
Example:
DTMF combination
Description
00
Deactivate ALL outputs
01
Activate ALL outputs
11
Activate output 1
20
Deactivate output 2
Table 5: DTMF control example
9.2 OUTPUT MANAGEMENT
ICE-ENTRY-100 supports the possibility to report alarms from inputs and any other
events locally via 4 outputs. The behavior is defined using next parameters
9.2.1 OS parameter
ICE-ENTRY-100 device has 2 dedicated relay supported outputs. Outputs can be
configured to different behavior:
⇒OS = 0 – Disabled
⇒OS = 1 – Bi-stable toggle mode
⇒OS = xxx – Mono-stable pulse mode ( duration in seconds )

ICE+ENTRY+100'
INSTALLATION'MANUAL+
Page%19%
Typical connection for the output:
Figure 3: Output Connection diagram
9.2.2 OD parameter
OD parameter is used to link the alarm event directly to output.
9.2.3 OP1, OP2 parameters
Parameters are used to invert the polarity of the outputs.
⇒0 – normal
⇒1 – inverted
9.2.4 Table of parameters
Name
Comment
OS1
Mode of operation for output 1
OS2
Mode of operation for output 2
OD1
Input 1 direct link to outputs
OD2
Input 2 direct link to outputs
OD3
NAC direct link to outputs
OP1
Invert control for output 1
OP2
Invert control for output 2
Table 6: Output management parameters
Example:
♦Direct programming on the SIM card