Travis Industries 36 CF II User manual

36 CF II
Gas Fireplace
Tested and Listed by
OMNI-Test Laboratories, Inc.
Beaverton, Oregon
Report # 028- -57-5
AN I Z21.88a-2003
• Built-In Direct Vent Fireplace
• Natural Gas or Propane
• Residential or Mobile Home
• Bedroom pproved
W RNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
WH T TO DO IF YOU SMELL G S
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the
gas supplier.
This appliance may be installed in an aftermarket permanently located, manufactured home (US only)
or mobile home, where not prohibited by local codes.
This appliance is only for use with the type(s) of gas indicated on the rating plate. conversion kit is
supplied with the appliance.
Installation Manual
Installer:fter installation give this manual to the home-
owner and explain operation of this heater.
 Copyright 2010, T.I. $10.00 100-01197_001 4100519 4800 Harbour Pointe Blvd. W
Mukilteo, WA 98275

2 Introduction
© Travis Industries 4100519 100-01197_001
Overview
This manual details the installation
requirements for the 36 CF II fireplace. For
operating and maintenance instructions, refer to
the 36 CF II Owner's Manual (part # 100-01198).
Listing Details
This appliance was listed by OMNI Test Labs to
AN I Z21.88 - report # 028- -57-5. The listing
label is attached to the appliance near the gas
control valve. A copy is shown to the right.
ICBO Approval
This appliance was listed by OMNI-Test
Laboratories - ICBO # TL130.
Massachusetts Approval
This manual has been submitted to the
Massachusetts Board of tate Examiners of
Plumbers and Gas Fitters
National Fireplace Institute
Figure 1

Table of Contents 3
© Travis Industries 4100519 100-01197_001
Introduction
Overview.................................................................2
Listing Details..........................................................2
Safety Precautions
afety Precautions...................................................4
Features and Specifications
Installation Options...................................................6
pecifications..........................................................6
Dimensions............................................................. 6
Installation
Packing List.............................................................7
Additional Items Required..........................................7
Installation Overview.................................................7
Recommended Installation Procedure .........................8
Massachusetts Requirements.....................................9
Preparing the Fireplace tand-offs..............................10
Fireplace Placement Requirements.............................12
Clearances...........................................................12
Raised Fireplaces .................................................12
Minimum Framing Dimensions ................................13
Framing Dimensions - Corner Installations................14
Nailing Brackets ....................................................15
Gas Line Requirements.............................................16
Gas Line Connection .............................................16
Gas Inlet Pressure ................................................16
Required Electrical Connection...................................17
Battery Pack – Learn witch Installation.......................18
Remote ynchronization............................................ 20
Installation (continued)
Vent Requirements .................................................. 21
Approved Vent......................................................21
Altitude Considerations..........................................21
Vent Clearances...................................................22
Vent Installation....................................................22
Approved Vent Configurations.................................... 23
Exhaust Restrictor Adjustment................................23
Intake Restrictor Adjustment ..................................23
Horizontal Termination (1 90° Elbow) ........................ 24
Horizontal Termination (3 90° Elbows)....................... 25
Vertical Termination (0, 2, or 4 45° Elbows)...............26
Vertical Termination (2 90° Elbows) ..........................27
Termination Requirements......................................... 28
Hearth Requirements ............................................... 29
Flush Hearth........................................................29
Hearth Requirements – Recessed Hearth ................30
Facing Requirements ............................................... 31
Non-Combustible Facing........................................32
Mantel Requirements................................................ 34
Finalizing the Installation
Air hutter Adjustment.............................................. 36
Glass Frame Removal and Installation........................ 37
Log et Installation .................................................. 39
Fireback Installation ................................................. 38
LP Conversion Instructions ....................................... 45
Andiron Installation................................................... 49
Index
Index...................................................................... 50

4 Safety Precautions
© Travis Industries 4100519 100-01197_001
Safety Warnings:
• Failure to follow all of the requirements may result in property damage, bodily injury, or even death.
• This unit must be installed by a qualified installer to prevent the possibility of an explosion.
• This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI
Z223.1 and NFPA 54(88).
• A manufactured home (USA only) or mobile home OEM installation must conform with the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a
standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1,
or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This
appliance may be installed in Manufactured Housing only after the home is site located.
• All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn
from outside the living-area structure. The venting must not be connected to a chimney flue serving a
separate solid-fuel burning appliance.
• Notify your insurance company before hooking up this fireplace.
• The room heater should be inspected before use and at least annually by a qualified service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.
• The instructions in this manual must be strictly adhered to. Do not use makeshift methods or
compromise in the installation. Improper installation will void the warranty and safety listing.
• This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will
void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about
the type of fuel used to your dealer. Check the label and flame adjust knob on the gas control valve.
• Contact your local building officials to obtain a permit and information on any installation restrictions or
inspection requirements in your area.
• If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call your
dealer and arrange for proper servicing.
• It is imperative that control compartments, screens, or circulating air passageways of the heater be
kept clean and free of obstructions. These areas provide the air necessary for safe operation.
• Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call your
dealer for a full explanation of your heater and what to expect.
• Do not store or use gasoline or other flammable liquids in the vicinity of this heater.
• Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.
• Do not place clothing or other flammable items on or near the heater. Because this heater can be
controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed
on or near it.
• Light the heater using the built-in piezo igniter. Do not use matches or any other external device to
light your heater.
• Never remove, replace, modify or substitute any part of the heater unless instructions are given in this
manual. All other work must be done by a trained technician. Don't modify or replace orifices.
• The viewing glass should be opened only for lighting the pilot or conducting service.
• Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5
© Travis Industries 4100519 100-01197_001
Safety Warnings (continued):
• Allow the heater to cool before carrying out any maintenance or cleaning.
• Operate the heater according to the instructions included in this manual.
• If the main burners do not start correctly turn the gas off at the gas control valve and call your dealer for
service.
• The pilot flame must contact the flame sensor. If it does not, turn the gas control valve to "OFF" and
call your dealer.
• This unit is not for use with solid fuel.
• Do not place anything inside the firebox (except the included fiber logs).
• If the fiber logs become damaged, replace with Travis Industries log set.
• Do not throw this manual away. This manual has important operating and maintenance instructions
that you will need at a later time. Always follow the instructions in this manual.
• Do not touch the hot surfaces of the heater. Educate all children of the danger of a high-temperature
heater. Young children should be supervised when they are in the same room as the heater.
• Due to the high temperature, the heater should be located out of traffic and away from furniture and
draperies.
• Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.
The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to
shut off.
• Travis Industries, Inc. grants no warranty, implied or stated, for the installation or
maintenance of your heater, and assumes no responsibility of any consequential
damage(s).

6 Features and Specifications
© Travis Industries 4100519 100-01197_001
Installation Options
• Residential or Mobile Home
• traight or Corner Placement
• Flush or Recessed Face
• Raised or Floor Placement
• Internal or External Chase
• Horizontal or Vertical Vent
• Bedroom Approved
Specifications
Natural Gas Propane
Maximum BTU Input Per Hour 50,000 49,000
Minimum BTU Input on Low 28,500 26,900
Dimensions
Tabs for lifting handles
(sku 98500711)
Weight: 250 Lbs.
1-1/2" **
* Includes the required 2" clearance.
** Includes the 1" standoff and 1/2" fiber board below the baseplate.
*** Does not include the required 4" clearance to each side.
25"*
49-1/2"
12-1/4"*
32-3/4" **
43" **
27" ***
NOTE: 4" Clearance to
the ides of the Fireplace
NOTE: 2" Clearance to
the Back of the Fireplace
8-5/8" Outside Diameter
41-1/2" **
5"
56-3/4" **
37-1/2"
32-1/4" **
27-1/4" **
36 CF A
36 CF R
32-3/4" **
38-1/4"
Radius
Figure 2

Installation (for qualified installers only) 7
© Travis Industries 4100519 100-01197_001
Packing List
• Propane Conversion Kit (orifice, rate scre )
• Log Set
• Remote Control ith Wall Mount
• Battery Box ith 12’ Wire Lead, Learn S itch
• Door Latch Tool
• Fiber Board
Additional Items Required
WARNING: Do not operate the fireplace ithout the firebacks in place. Failure to install the firebacks
ill result in an extreme fire hazard and ill void the listing and arranty of this fireplace.
• Firebacks –Arched (9 1001 ) - Rectangular (9 100172) available from Travis Industries
• 1080/36 CF Direct Vent (available only from Travis Industries – see page 21 for part numbers)
• Gas Line Equipment (shutoff valve, pipe, etc.)
Installation Overview
• All requirements belo must be met.
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
The fireplace must be
placed on the included
fiber board - see the
section "Fireplace
Placement Requirements"
Non-combustible facing -
(included) see the section
"Facing Requirements"
See the section
"Vent Requirements"
See the section
"Minimum Framing Dimensions"
Nailing Brackets
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
Drywall (or other
combustible)
10.25"
Min.
See the section
"Mantel Requirements"
See the section
"Hearth Requirements"
See the section
"Control Panel Installation"
NOTE: Control wire is 12' long.
Side
Wall
Figure 3

8 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
Recommended Installation Procedure
1. Frame the opening for the fireplace. We suggest omitting the framing above the header to
allo for easier vent installation.
2. Place the fireplace in place, making sure it is level and plumb. Attach using the nailing
brackets.
3. Install the vent, gas line, electrical connection, and battery box.
4. Install the framing above the header.
5. Install the hearth (if applicable).
6. Install the included non-combustible fiber board.
7. Install the facing.
8. Install the mantel (if applicable).
9. Finalize the installation (see page 35).

Installation (for qualified installers only) 9
© Travis Industries 4100519 100-01197_001
Massachusetts Requirements
NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.
Requirements for the Commonwealth of Massachusetts
For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in
part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent
termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and
porches, the following requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall
observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the
gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard
wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served
by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the
services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired
carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day
period, a battery operated carbon monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be
ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or
equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP
CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.
Exemptions
The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as
adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or
venting system components with the equipment, the instructions provided by the manufacturer for installation of the
equipment and the venting system shall include:
• Detailed instructions for the installation of the venting system design or the venting system components; and
• A complete parts list for the venting system design or venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts
for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the
manufacturer:
• The referenced “special venting system” instructions shall be included with the appliance or equipment installation
instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.

10 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
Preparing the Fireplace Stand-offs
This appliance is shipped ith the header and side stand-offs in the retracted position. These stand-
offs must be placed in their upright position prior to installing the fireplace
WARNING: Failure to correctly erect the stand-offs may lead to a serious fire-hazard and ill void
the listing and arranty of this fireplace.
Side Stand-Offs
Bend the side stand-off until it is flat.
Remove the two screws behind the side
stand-off and place them aside.
Bend the stand-off return back until
the holes in the stand-off line up with
the holes on the side of the fireplace.
a
b
c
d
Secure the stand-off with two
screws removed earlier.
Repeat steps "a", "b", and "c"
for the opposite side.
Figure 4

Installation (for qualified installers only) 11
© Travis Industries 4100519 100-01197_001
Header Stand-Off
Rotate the header standoff until
the side braces lock into place.
Rotate the header brackets up
The notch in the side brace slides
over this screw.
a
cUn-fold the side of the header
standoff until it is flat (both sides).
Remove the screw below
the center header standoff.
Rotate the lower standoff upwards
and attach using the same screw.
b
d
Figure 5

12 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
Fireplace Placement Requirements
• The fireplace requires a 4" clearance from the sides and 2” from the back of the fireplace to the
framing members. No material (insulation, framing, etc.) may be placed into this area.
• Fireplace must be placed in a room ith a minimum 96” ceiling.
• Fireplace must be placed on the t o 25” by 24” pieces of fiber board (see Figure 6). The
fiberboard must be placed on the sub-floor or a ood platform (not on linoleum or carpet).
• Fireplace must be installed on a level surface capable of supporting the fireplace and vent.
• This heater may be placed in a bedroom. Please be a are of the large amount of heat this
appliance produces hen determining a location.
Clearances
• When installed, alls in front of the fireplace must be a minimum 10-1/4” from the glass frame
(4-1/4" from the side stand-offs - see Figure 3).
• Due to the high temperature, the heater should be located out of traffic and a ay from furniture
and draperies.
• Fireplace must be placed so the vents belo and above the glass do not become blocked.
Raised Fireplaces
• The fireplace (and hearth, if desired) may be placed on a platform designed to support the
fireplace 250 Lbs.) and vent.
24”25”
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
AAAAAAAAAA
Place the two 24”x 25”pieces of
fiber board directly under the
fireplace, along the front edge of
the framing.
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAA
AAA
AAAAA
AAAAA
AAAAA
AAAAA
AAAAA
AAAAA
AAA
AAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAA
AAA
AAAAA
AAAAA
Minimum 82”Fireplace
Enclosure Height.
Optional Raised Hearth
(see “Hearth Requirements”for details)
Platform with
Plywood Top
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAA
AAAA
AAAA
AAAAA
AAAAA
AAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAA
AAAAA
AAAAA
AAAA
AAAA
AAAA
Figure

Installation (for qualified installers only) 13
© Travis Industries 4100519 100-01197_001
Minimum Framing Dimensions
NOTE: Do not build into this area - it must be left clear to
provide adequate clearance for the vent. A maximum 3-1/2”
depth is allowed in this 14”wide area centered along the front
of the fireplace.
14”Min.
50”
3.5”Max.
56-3/4”*
25”
Minimum 82”Fireplace
Enclosure Height
NOTE: On LP
installations with
minimum vertical rise,
minimum enclosure
height is 96”.
* Includes the 1/2”fiber board.
Figure 7

14 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
Framing Dimensions - Corner Installations
A typical 45° installation uses the framing dimensions sho n in the illustration belo (NOTE: all
clearances still apply).
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
59"
(approximate)
AAAAAAAAAAA
AAAAAAAAAAA
AA
AA
AAAAAAAAAAA
Minimum 2"
Clearance
AAAA
AAAA
AAAA
AAAA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
21.25"
(approximate)
Figure 8

Installation (for qualified installers only) 15
© Travis Industries 4100519 100-01197_001
Nailing Brackets
Use screws or nails to
secure the fireplace to the
framing with the six nailing
brackets.
1
2
3
4
5
6
7
Figure 9

1 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
as Line Requirements
MASSACHUSETTS INSTALLATIONS - WARNING:
THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUMBER OR GAS FITTER WHEN INSTALLED WITHIN
THE COMMONWEALTH OF MASSACHUSETTS.
OTHER MASSACHUSETTS CODE REQUIREMENTS:
• Flexible connector must not be longer than 36 inches.
• Shutoff valve must be a “T” handle gas cock.
• Only direct vent sealed combustion products are approved for bedrooms or bathrooms.
• Fireplace dampers must be removed or elded in the open position prior to the installation of a fireplace insert or gas
log.
• A carbon monoxide (CO) detector is required in the same room as the appliance.
• The gas line must be installed in accordance ith all local codes, if any; if not, follo ANSI 223.1 and the
requirements listed belo .
• The fireplace and gas control valve must be disconnected from the gas supply piping during any pressure
testing of that system at test pressures in excess of 1/2 psig. For pressures under 1/2 psig, isolate the
gas supply piping by closing the manual shutoff valve.
• Leak test all gas line joints and the gas control valve prior to and after starting the fireplace.
• This fireplace is designed either for natural gas or for propane (but not for both). Check the gas control valve to
make sure the correct fuel is used.
• An additional shut-off valve is required. It must be accessible and within 6’of the fireplace.
Gas Line Connection
• Installation must be performed by a qualified installer, service agency or the gas supplier (In Massachusetts
a licensed plumber/gasfitter).
• A shutoff valve is built into the fireplace. It is located on the left side of the fireplace and acts as the gas
inlet connection. After installing the gas line (and testing), remove the cover plate sho n belo and turn the
gas shutoff valve to “ON”.
The gas inlet is located
5.5" above the base of
the fireplace.
7"
4"
Built-In Shut-off Valve
Gas Line
(1/2" M.P.T.)
Shutoff Valve
Gas Inlet
LEFT SIDE OF
FIREPLACE
Figure 10
Gas Inlet Pressure Standard Input Pressure
Natural Gas 7" W.C. (1.74 kPA)
Propane 13" W.C. (2.73 kPA)
• If the pressure is not sufficient, make sure the piping used is large enough, the supply regulator is
adequately adjusted, and the total gas load for the residence does not exceed the amount supplied.
• The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should
supply gas at the suggested input pressure listed above. Contact the local gas supplier if the regulator is at
an improper pressure.

Installation (for qualified installers only) 17
© Travis Industries 4100519 100-01197_001
Required Electrical Connection
Make sure power to the heater has been turned off prior to installation (disable the breaker).
Do not connect 110-120 VAC to the gas control valve or the on/off circuit on this fireplace.
This fireplace utilizes 110 VAC to po er the receiver module and intermittent pilot system. A
separate battery box is included to provide po er in case of po er outages (see “Battery Pack –
Learn S itch Installation” on page 18 for details).
• The electrical line to the grounded receptacle inside the fireplace must be installed by a
qualified installer and must meet all local codes. The fireplace must be properly grounded in
accordance ith local codes (or ANSI/NFPA 70-1987).
• Make sure the household breaker is shut off prior to orking on any electrical lines.
• The fireplace must be properly grounded in accordance ith local codes (or ANSI/NFPA 70-1987)
• The electrical line must be a min. 14 gauge, and supply 120 Volts at 60 Hz (2 Amps)
Caution: Label all ires prior to disconnection hen servicing controls. Wiring errors can cause
improper and dangerous operation.
• Attach an electrical line to the receptacle inside the control box (see the illustration belo ).
Make sure to connect the ground ire to the grounding tab on the receptacle (this grounds the
fireplace).
Grounded 110V
Po er Supply
Attach the electrical line,
including the grounding ire,
to this receptacle.
Control Box
Cover Plate
Romex Connector

18 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
Battery Pack – Learn Switch Installation
• The battery pack and learn s itch must be mounted inside a junction box in a location that
may be reached by the 12’ long battery box ires (see Figure 11).
Staple the two wires near the junction
box. This prevents the wires from
slipping out of the junction box while
the batteries are replaced. Take care
to prevent damage to wires.
Junction Box
(not supplied)
Battery Box and Learn Switch
(placed inside the junction box)
Remote Holder - used to cover the
junction box. It is removed to
replace batteries and access the
learn switch
Battery Box Wire
Remove the Control Box to access the battery box wire. See the
illustration on the following page for wiring details.
Wire Length = 12'
Do not route the wires over the top
of the fireplace.
Figure 11

Installation (for qualified installers only) 19
© Travis Industries 4100519 100-01197_001
Steps for Installing the Battery Pack and Wall Switch
1. Remove the control cover and attach the 12’ long battery box ire to the quick connects on the receiver
module (see Figure 12 belo ). Route the battery box ire through the opening belo the cover. At this
time make sure the continuous pilot s itch is set to “OFF” and the remote s itch is set to “REMOTE” on the
receiver module – item “a”). You may also ish to verify all the ire leads are fully attached.
POWER
MOTOR
Learn
Continuous
Pilot
Off/On Remote/Off ADJ
SI
Motor Wires (for flame height adjustment)
Red, Yellow, White, and Blue wires
White
Green
Orange
White
Main Burner Control Wires
Pilot Flame Control Wires
Sensor ("S")
Wire (White)
Brown Switch
Wires (not
used)
Battery Box
(external junction box)
Gas Control Valve
Receiver
Module
Pilot Assembly
Make sure continuous pilot
is set to "OFF" and remote
is set to "REMOTE".
a
Igniter ("I") Wire
(Orange - with
fiberglass
insulation)
AC Adapter
(wire orientation does not matter)
COMM.
Black
Ground
Battery Wires
Red and White Wires
Learn Wires
Two White Wires
Figure 12
2. Determine a location for the single-gang junction box that contains the battery pack and learn s itch. It
must be located ithin 12’ of the fireplace. Mount the junction box.
3. Insert the battery box ires through the junction box, leaving approximately 8” of slack so the battery pack
may be removed and the batteries replaced. Use a staple or other means to secure the iring to the
framing – this prevents the ires from slipping out of the junction box in the event the ires become
disconnected from the battery pack (see Figure 11). NOTE: The iring is lo -voltage (6V) and does not
require a strain relief. Connect the learn s itch and battery pack ires (see Figure 12).
4. Place batteries inside the battery pack and place it inside the junction box. Attach the remote holder to the
junction box ith the included scre s.
INSTALLATION WARNING – Remote Synchronization
At this time e highly recommend you verify the remote and fireplace are synchronized. This
process requires access to the learn s itch. See the instructions on page 20 for details.
Battery Installation
This fireplace uses four AA batteries for operation during po er outages. Place the batteries into the battery
box. In addition, t o AAA batteries are required for the transmitter.

20 Installation (for qualified installers only)
© Travis Industries 4100519 100-01197_001
Remote Synchronization
The fireplace is shipped with the remote and fireplace pre-synchronized . Do not
synchronize the remote unless you are 100% sure it does not work correctly.
Synchronizing the Remote
NOTE: The fireplace must have po er and the transmitter must have batteries to complete this process.
WARNING: Shut the gas off to the fireplace prior to conducting this process.
1 Press the “Learn” button once. The fireplace ill beep once.
2 Press the “Mode” button on the remote. The fireplace ill beep five times to indicate
synchronization.
NOTE: Re-setting the Receiver Module
If the receiver module fails to synchronize ith the remote after t o attempts, you should re-set the
receiver module. To do this, hold do n the LEARN button for approximately 10 seconds until the
receiver beeps 3 times. This indicates the receiver has been re-set and can be synchronized using
the instructions above.