Treasure Garden Starlux Collar Tilt Installation instructions

UM800xLX
9’ OC
Starlux Collar Tilt
Assembly and Operation Guide
www.treasuregarden.com
©2019 Treasure Garden, Inc. - All Rights Reserved. 9/19
WARRANTY:
Treasure Garden warrants this product
(in residential use) to be free from defects
in original materials and workmanship for a
period of 2 years from the date of
purchase. If a defect in the original
material or workmanship appears during
the warranty period; Treasure Garden will
(at its option) repair or replace the product
without charge. Limited warranty against
fabric fading, depending on fabric.
Simply contact your original authorized
Treasure Garden dealer with a description
of the defect. The dealer will verify the
defect and work closely with Treasure
Garden to obtain the necessary service.
In many cases, simple problems can be
solved with a replacement part that can be
shipped directly to the dealer for
professional installation/repair.
In the event that warranted factory service
is required, Treasure Garden will assume
the responsibility of the return freight
charges on warranted product for the
2 years only.
Returned product that (upon receipt and
inspection) is deemed to be “not covered”
under our warranty, will be shipped/billed
at your expense.
This warranty gives you specific legal rights,
and you may have other rights which vary
from state to state.
NOTE: Failure caused by unreasonable or
abusive use, or failure caused by neglect of
reasonable and necessary care are not
covered by this warranty.
Additionally, acts of nature (including but not
limited to wind, hurricanes, tornadoes, and
storms) are not covered by this warranty.

A - Finial
B - Canopy/Mainframe
C - Bottom Pole
D - Rechargeable Battery Pack
E - Power Cord*
F - BW Base Stopper
*Note: Use only the Power Cord supplied.
61
Thank you for purchasing Treasure Garden’s Starlux Collar Tilt Umbrella.
Please remove all contents from the package, inspect and review checklist.
STARLUX COLLAR TILT CHECKLIST
A -
B -
C -
S A F E T Y P R E C A U T I O S :
• Close and store the umbrella in windy conditions or when a storm approaches.
ever allow the umbrella to flap in the wind; this could damage the canopy.
• Do not leave open umbrella unattended. If damage occurs, this is not covered
by the warranty.
• When adjusting the umbrella, make sure that no person(s) or item(s) are close to the
umbrella. This is important to prevent injury or material damage.
• Do not operate the Starlux power switch, USB port or attempt to charge the umbrella in
inclement weather (rain, snow) so as to prevent damage to the electrical components.
• Do not leave rechargeable battery pack in sun, it will affect battery life.
C A R E A D M A I T E A C E :
• When not in use, close and cover umbrella with a protective cover (not included).
• Store rechargeable battery pack and power cord in dry place.
• Allow a wet canopy to dry while in open position.
• If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.
• Wipe sliding marks on the aluminum poles with a damp cloth.
Storage:
• Store in a dry, protective place.
• Store battery pack, along with power supply/transformer in dry, cool area to keep
from damaging.
After the Winter:
• Areas subject to turning and sliding can be treated with a non-staining lubricant spray
(silicone-based).
• Check the condition and function of the umbrella. Any defects must be repaired by a
professional.
S T E P 1 Set Up
Carefully remove umbrella from box. Attach finial to top of canopy/mainframe (Fig. 1).
E -
D -
F -
(Fig. 1)
Connect bottom pole and canopy/mainframe plugs together (Fig. 2).
(Fig. 2)

25
Insert bottom pole into canopy/mainframe pole. NOTE: Make sure battery dock on bottom
pole is lined up with O /OFF switch and USB port on housing. Line up button with hole
and snap into place (Fig. 3).
To close umbrella, twist collar in counter-clockwise direction to bring umbrella back to its
original upright position (Fig. 15). Turn crank in counter-clockwise direction until fully closed.
Properly fold canopy, tie string around canopy and cover umbrella with a protective cover
(not included).
(Fig. 3)
S T E P 2 BW Base Stopper (For BW Classic Base Only)
To avoid the BW Classic Base stem from interfering with the battery, base stopper must be
installed under base.
Turn BW Classic Base on its side. Attach Base Stopper to underside of base by turning
clockwise until tightened (Fig. 4). Turn base back to upright position (Fig. 5).
IMPORTANT:
If you are using a BW Classic Base with your Starlux Collar Tilt, you must attach Base Stopper
to your BW Classic Base. If you are not using a BW Classic Base OR if you have a BW30
Add-on Weight attached to your BW Classic Base, please proceed to Step 3.
(Fig. 4) (Fig. 5)
To turn umbrella lights on or off, press on/off switch located
on collar housing (Fig. 13).
WARNING: We do not recommend use of lights while
raining. When lights are not in use, remove battery pack from
umbrella. Store battery pack, along with power supply in dry,
cool area to keep from damaging.
On/Off Switch
(Fig. 13)
To charge electronic devices, remove plug from USB port
(Fig. 14). Insert USB cable into USB port. Reattach plug when
not in use. Note: If using USB port and lights, battery life will
reduce to 4 hours.
USB Port
(Fig. 14)
(Fig. 15)

43
S T E P 4 Operating Umbrella
Crank handle clockwise to open umbrella to its fully open position (Fig. 11).
To tilt, simply twist the collar in clockwise direction (Fig. 12).
S T E P 3 Rechargeable Battery Pac
Turn umbrella in upright position. Insert bottom pole into free standing base (Fig. 6) or
through table top. IMPORTANT: If using table application, please take note of measurements
below to ensure table can accommodate battery pack (Fig. 7).
Free Standing Table Application
18.3”
4.6”
1. 4 ”
9.1”
32”
2
”
DIA.
28”
3.5”
(Height toTABLE
BOTTOM)
(BOTTOM POLE)
T
ABLE
UMBRELLA
HOLE
BATTERY
+POLE & BATTERY
CLEARANCE
3.5”
DIA.
(WHEN ATTACHED)
(Fig. 6) (Fig. 7)
(Fig. 8)
BATTERY
3.5”
DIA.
3.5”
DIA.
(Fig. 11)
(Fig. 12)
Attach rechargeable battery pack onto bottom pole (Fig. 8).
Charging Battery Pac :
You must fully charge battery pack prior to first use.
To charge battery, remove plug cap from charging port on
battery pack. Using the supplied power cord/transformer,
insert power supply into charging port. Plug other end of
power supply into wall outlet for 6 hours to fully charge
(Fig 9). When fully charged, all lights displayed on battery
pack will be lit.
Battery Status: Lights on the battery pack will indicate
battery charge level (Fig. 10). Four lights indicates full charge,
while one is low battery. When battery is low, you may
charge battery pack while attached to frame, or removed
from frame, using supplied power cord/transformer.
(Fig. 9)
Note: The transformer output power is 12V. It is normal for transformer to get warm after
long period of use. Avoid sun and water on power supply/transformer to increase lifetime
use. Be sure not to drop transformer or battery pack. Only use Power Cord/Transformer
supplied.
(Fig. 10)

43
S T E P 4 Operating Umbrella
Crank handle clockwise to open umbrella to its fully open position (Fig. 11).
To tilt, simply twist the collar in clockwise direction (Fig. 12).
S T E P 3 Rechargeable Battery Pac
Turn umbrella in upright position. Insert bottom pole into free standing base (Fig. 6) or
through table top. IMPORTANT: If using table application, please take note of measurements
below to ensure table can accommodate battery pack (Fig. 7).
Free Standing Table Application
18.3”
4.6”
1. 4 ”
9.1”
32”
2
”
DIA.
28”
3.5”
(Height toTABLE
BOTTOM)
(BOTTOM POLE)
T
ABLE
UMBRELLA
HOLE
BATTERY
+POLE & BATTERY
CLEARANCE
3.5”
DIA.
(WHEN ATTACHED)
(Fig. 6) (Fig. 7)
(Fig. 8)
BATTERY
3.5”
DIA.
3.5”
DIA.
(Fig. 11)
(Fig. 12)
Attach rechargeable battery pack onto bottom pole (Fig. 8).
Charging Battery Pac :
You must fully charge battery pack prior to first use.
To charge battery, remove plug cap from charging port on
battery pack. Using the supplied power cord/transformer,
insert power supply into charging port. Plug other end of
power supply into wall outlet for 6 hours to fully charge
(Fig 9). When fully charged, all lights displayed on battery
pack will be lit.
Battery Status: Lights on the battery pack will indicate
battery charge level (Fig. 10). Four lights indicates full charge,
while one is low battery. When battery is low, you may
charge battery pack while attached to frame, or removed
from frame, using supplied power cord/transformer.
(Fig. 9)
Note: The transformer output power is 12V. It is normal for transformer to get warm after
long period of use. Avoid sun and water on power supply/transformer to increase lifetime
use. Be sure not to drop transformer or battery pack. Only use Power Cord/Transformer
supplied.
(Fig. 10)

25
Insert bottom pole into canopy/mainframe pole. NOTE: Make sure battery dock on bottom
pole is lined up with O /OFF switch and USB port on housing. Line up button with hole
and snap into place (Fig. 3).
To close umbrella, twist collar in counter-clockwise direction to bring umbrella back to its
original upright position (Fig. 15). Turn crank in counter-clockwise direction until fully closed.
Properly fold canopy, tie string around canopy and cover umbrella with a protective cover
(not included).
(Fig. 3)
S T E P 2 BW Base Stopper (For BW Classic Base Only)
To avoid the BW Classic Base stem from interfering with the battery, base stopper must be
installed under base.
Turn BW Classic Base on its side. Attach Base Stopper to underside of base by turning
clockwise until tightened (Fig. 4). Turn base back to upright position (Fig. 5).
IMPORTANT:
If you are using a BW Classic Base with your Starlux Collar Tilt, you must attach Base Stopper
to your BW Classic Base. If you are not using a BW Classic Base OR if you have a BW30
Add-on Weight attached to your BW Classic Base, please proceed to Step 3.
(Fig. 4) (Fig. 5)
To turn umbrella lights on or off, press on/off switch located
on collar housing (Fig. 13).
WARNING: We do not recommend use of lights while
raining. When lights are not in use, remove battery pack from
umbrella. Store battery pack, along with power supply in dry,
cool area to keep from damaging.
On/Off Switch
(Fig. 13)
To charge electronic devices, remove plug from USB port
(Fig. 14). Insert USB cable into USB port. Reattach plug when
not in use. Note: If using USB port and lights, battery life will
reduce to 4 hours.
USB Port
(Fig. 14)
(Fig. 15)

A - Finial
B - Canopy/Mainframe
C - Bottom Pole
D - Rechargeable Battery Pack
E - Power Cord*
F - BW Base Stopper
*Note: Use only the Power Cord supplied.
61
Thank you for purchasing Treasure Garden’s Starlux Collar Tilt Umbrella.
Please remove all contents from the package, inspect and review checklist.
STARLUX COLLAR TILT CHECKLIST
A -
B -
C -
S A F E T Y P R E C A U T I O S :
• Close and store the umbrella in windy conditions or when a storm approaches.
ever allow the umbrella to flap in the wind; this could damage the canopy.
• Do not leave open umbrella unattended. If damage occurs, this is not covered
by the warranty.
• When adjusting the umbrella, make sure that no person(s) or item(s) are close to the
umbrella. This is important to prevent injury or material damage.
• Do not operate the Starlux power switch, USB port or attempt to charge the umbrella in
inclement weather (rain, snow) so as to prevent damage to the electrical components.
• Do not leave rechargeable battery pack in sun, it will affect battery life.
C A R E A D M A I T E A C E :
• When not in use, close and cover umbrella with a protective cover (not included).
• Store rechargeable battery pack and power cord in dry place.
• Allow a wet canopy to dry while in open position.
• If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.
• Wipe sliding marks on the aluminum poles with a damp cloth.
Storage:
• Store in a dry, protective place.
• Store battery pack, along with power supply/transformer in dry, cool area to keep
from damaging.
After the Winter:
• Areas subject to turning and sliding can be treated with a non-staining lubricant spray
(silicone-based).
• Check the condition and function of the umbrella. Any defects must be repaired by a
professional.
S T E P 1 Set Up
Carefully remove umbrella from box. Attach finial to top of canopy/mainframe (Fig. 1).
E -
D -
F -
(Fig. 1)
Connect bottom pole and canopy/mainframe plugs together (Fig. 2).
(Fig. 2)

UM800xLX
9’ OC
Starlux Collar Tilt
Assembly and Operation Guide
www.treasuregarden.com
©2019 Treasure Garden, Inc. - All Rights Reserved. 9/19
WARRANTY:
Treasure Garden warrants this product
(in residential use) to be free from defects
in original materials and workmanship for a
period of 2 years from the date of
purchase. If a defect in the original
material or workmanship appears during
the warranty period; Treasure Garden will
(at its option) repair or replace the product
without charge. Limited warranty against
fabric fading, depending on fabric.
Simply contact your original authorized
Treasure Garden dealer with a description
of the defect. The dealer will verify the
defect and work closely with Treasure
Garden to obtain the necessary service.
In many cases, simple problems can be
solved with a replacement part that can be
shipped directly to the dealer for
professional installation/repair.
In the event that warranted factory service
is required, Treasure Garden will assume
the responsibility of the return freight
charges on warranted product for the
2 years only.
Returned product that (upon receipt and
inspection) is deemed to be “not covered”
under our warranty, will be shipped/billed
at your expense.
This warranty gives you specific legal rights,
and you may have other rights which vary
from state to state.
NOTE: Failure caused by unreasonable or
abusive use, or failure caused by neglect of
reasonable and necessary care are not
covered by this warranty.
Additionally, acts of nature (including but not
limited to wind, hurricanes, tornadoes, and
storms) are not covered by this warranty.