Treasure Garden UM801 Installation instructions

UM801/UM800/UM812/
UM810/UM920
Collar/Auto/Push Button Tilt
Rib Replacement
Assembly and Operation Guide
www.treasuregarden.com
©2014 Treasure Garden, Inc. - All Rights Reserved. 10 /14
S T E P 6 Rep ace Canopy & Finia
Turn crank to lower canopy. Replace canopy back
onto umbrella and reattach finial by turning clockwise
(Fig. 15). Place umbrella upright in base. Your
umbrella is now ready for use.
(Fig. 15)
S T E P 5 Insert New Rib From Notch
Insert new rib into notch, carefully aligning the pin in its slot (Fig. 12). Replace the top half of
notch. Make certain the guide is aligned with its corresponding hole (Fig. 13). Replace the
top half of the notch and screw it back into place (Fig. 14).
(Fig. 12) (Fig. 13) (Fig. 14)
Guide Hole
(Fig. 10)
S T E P 4 Remove Rib From Notch
Crank umbrella open. Remove umbrella from base and set it down sideways on a soft, flat
surface with the broken rib facing up. Using a philips screwdriver, unscrew notch, remove
top and set aside (Fig. 10). Remove the broken rib from notch and discard (Fig. 11).
(Fig. 11)
Broken Rib

21
(Fig. 1)
(Fig. 2)
Pin
(Fig. 7) (Fig. 9)(Fig. 8)
RIB REPLACEMENT MANUAL
S T E P 1 Identify Broken Rib
Crank open the umbrella and identify the broken rib (Fig. 1). Set the umbrella down
sideways on a soft, flat surface.
RE UIRED ITEMS:
• Phillips head screwdriver
NOTE: Read these instructions completely before attempting replacement. These instructions
are specifically for Treasure Garden’s collar tilt, auto tilt or push button series umbrellas.
For Co ar Ti t/Auto Ti t Mode s: (For Push Button, proceed to Step 2.2)
S T E P 2 . 1 Remove Rib From Runner
Using a philips screwdriver, remove screws from runner (Fig. 2) and set screw aside. Place
the umbrella upright in its base, being careful not to dislodge the ribs from the runner. Crank
umbrella counter-clockwise until runner reaches eye-level. Carefully pull up the top half of the
runner from the bottom half (Fig. 3). Do not dislodge any other ribs or pins. Remove broken
rib. Proceed to Step 3.
S T E P 3 Attach New Rib
Attach new rib. Carefully place the ribs and pins back into runner, making certain that the pins
are aligned in their slots (Fig. 7). Carefully push the top half and bottom half of runner back
together (Fig. 8). Reattach screw into runner (Fig. 9). The new rib should now be in place in
the runner. The broken rib should still be hanging from the notch at the top of the umbrella.
(Fig. 3)
Slot
(Fig. 6)
For Push Button Ti t Mode s:
S T E P 2 . 2 Remove Rib From Runner
Using a philips screwdriver, remove screws from runner (Fig. 4) and set screw aside. Place
the umbrella upside down (Fig. 5), being careful not to dislodge the ribs from the runner.
Carefully pull up the bottom half of the runner from the top half (Fig. 6). Do not dislodge any
other ribs or pins. Remove broken rib.
(Fig. 4) (Fig. 5)

21
(Fig. 1)
(Fig. 2)
Pin
(Fig. 7) (Fig. 9)(Fig. 8)
RIB REPLACEMENT MANUAL
S T E P 1 Identify Broken Rib
Crank open the umbrella and identify the broken rib (Fig. 1). Set the umbrella down
sideways on a soft, flat surface.
RE UIRED ITEMS:
• Phillips head screwdriver
NOTE: Read these instructions completely before attempting replacement. These instructions
are specifically for Treasure Garden’s collar tilt, auto tilt or push button series umbrellas.
For Co ar Ti t/Auto Ti t Mode s: (For Push Button, proceed to Step 2.2)
S T E P 2 . 1 Remove Rib From Runner
Using a philips screwdriver, remove screws from runner (Fig. 2) and set screw aside. Place
the umbrella upright in its base, being careful not to dislodge the ribs from the runner. Crank
umbrella counter-clockwise until runner reaches eye-level. Carefully pull up the top half of the
runner from the bottom half (Fig. 3). Do not dislodge any other ribs or pins. Remove broken
rib. Proceed to Step 3.
S T E P 3 Attach New Rib
Attach new rib. Carefully place the ribs and pins back into runner, making certain that the pins
are aligned in their slots (Fig. 7). Carefully push the top half and bottom half of runner back
together (Fig. 8). Reattach screw into runner (Fig. 9). The new rib should now be in place in
the runner. The broken rib should still be hanging from the notch at the top of the umbrella.
(Fig. 3)
Slot
(Fig. 6)
For Push Button Ti t Mode s:
S T E P 2 . 2 Remove Rib From Runner
Using a philips screwdriver, remove screws from runner (Fig. 4) and set screw aside. Place
the umbrella upside down (Fig. 5), being careful not to dislodge the ribs from the runner.
Carefully pull up the bottom half of the runner from the top half (Fig. 6). Do not dislodge any
other ribs or pins. Remove broken rib.
(Fig. 4) (Fig. 5)

UM801/UM800/UM812/
UM810/UM920
Collar/Auto/Push Button Tilt
Rib Replacement
Assembly and Operation Guide
www.treasuregarden.com
©2014 Treasure Garden, Inc. - All Rights Reserved. 10 /14
S T E P 6 Rep ace Canopy & Finia
Turn crank to lower canopy. Replace canopy back
onto umbrella and reattach finial by turning clockwise
(Fig. 15). Place umbrella upright in base. Your
umbrella is now ready for use.
(Fig. 15)
S T E P 5 Insert New Rib From Notch
Insert new rib into notch, carefully aligning the pin in its slot (Fig. 12). Replace the top half of
notch. Make certain the guide is aligned with its corresponding hole (Fig. 13). Replace the
top half of the notch and screw it back into place (Fig. 14).
(Fig. 12) (Fig. 13) (Fig. 14)
Guide Hole
(Fig. 10)
S T E P 4 Remove Rib From Notch
Crank umbrella open. Remove umbrella from base and set it down sideways on a soft, flat
surface with the broken rib facing up. Using a philips screwdriver, unscrew notch, remove
top and set aside (Fig. 10). Remove the broken rib from notch and discard (Fig. 11).
(Fig. 11)
Broken Rib