Trelawny TFS230 User manual

www.trelawny.co.uk
735.5230
TFS230
FLOOR STRIPPER
OPERATION AND
MAINTENANCE MANUAL

PAGE 2
TFS230 Floor Stripper
CONTENTS
Introduction ................................................................................................................................................................ 2
Declaration of Conformity..................................................................................................................................... 3
General Information ................................................................................................................................................ 6
Safety ............................................................................................................................................................................. 6
Risk of Hand-Arm Vibration Injury..................................................................................................................... 7
Assembly Instructions ............................................................................................................................................ 7
Pre Start Checks (Daily) .......................................................................................................................................... 8
Starting - Electric Motors ...................................................................................................................................... 8
Handle Adjustment .................................................................................................................................................. 9
Blade Replacement ................................................................................................................................................. 9
Blade Angle Adjustment........................................................................................................................................ 10
PPE and Warning Hazard Symbols Explanation ......................................................................................... 10
Machine Operation ................................................................................................................................................... 11
Maintenance and Machine Storage.................................................................................................................. 11
Exploded View ........................................................................................................................................................... 12
Wiring Diagrams ....................................................................................................................................................... 13
Parts List TFS230 ...................................................................................................................................................... 14
Technical Specication........................................................................................................................................... 15
Trouble Shooting....................................................................................................................................................... 15
Notes ............................................................................................................................................................................... 16
INTRODUCTION
WARNING
Carefully read through these original instructions before using your new TRELAWNY power
tool. Take special care to read the warnings. Your TRELAWNY power tool has many features
that will make your job faster and easier. Safety, performance, and dependability have been
given top priority in the development of this tool, making it easy to maintain and operate.
ENVIRONMENTAL PROTECTION
The machine, accessories and packaging should be sorted for environmentally friendly
recycling. The plastic components are labelled for categorised recycling.
DISPOSAL
Waste products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your local authority or retailer for recycling advice.
Your new Trelawny SPT power tool will more than satisfy your expectations. It has been manufactured under
stringent Trelawny SPT Quality Standards to meet superior performance criteria. You will nd your new tool easy
and safe to operate, and, with proper care, it will give you many years of dependable service.

www.trelawny.co.uk

PAGE 4
TFS230 Floor Stripper

www.trelawny.co.uk
www.trelawny.co.uk 5
TFP200
DECLARATION OF CONFORMITY
CZ Prohlášenl o přizpüsobení
My, společnost Trelawny SPT Limited
podajemy daňové přiznáni. že výrobek a dodávka výrobku
název výrobku
Model, výrobni čislo
Rok výroby
Pro které se průkaz týkajici, je přizpůsobeni s zásoby od následujici přikazov a jejich pohotovostni:
98/37/EC Přikaz soustroji
73/23/EC Přikaz nizkého napéti (upotřebitelne jediné do výrobku použiti elektnckej energie)
LT ATITIKTIES DEKLARACIJA’
Mes, Trelawny SPT Limite
Prisiimdami visą atsakomybę deklaruojame, kad tiekiamas / gaminamas produktas
Produkto pavadinimas
Modelis, serijos numeris
Pagaminimo
Kuriam taikoma ši deklaracija, atitinka šių direktyvų, norminių aktų ir su jais susijusių. standartų reikalavimus:
98/37/EC ļtrangos direktyva
73/23/EC Zemos įtampos direktyva (taikoma tik elektriniams įrengimams)
DE Ubereinstimmungserklarung
Wir, Trelawny SPT Limited
erklaren, dass unter unserer alleinigen Verantwortung fur die Lieferung und Herstellung des Produktes
Name des Produktes
Model, Seriennummer
Jahr der Herstellung
auf welches sich dieses Dokument bezieht. stimmt mit den Vorgaben der folgenden Direktive, normativen Dokumente und deren
jeweiligen Masstabe ein:
98/71/EC Maschineriedirektive
73/23/EC Niederspannungsdirektive (nur zutreffend auf Produkte, die Strom benutzen)
MT DIKJARAZZJONI TA KONFORMITA
Aħna, Trelawny SPT Limited
Niddikjaraw li aħna responsabbli kompletament għal provista / manifattura tal-prodott hawn 1msemmi:
lsem ll-Prodott
Mudell, Serial number
Sena Ia 'produzzjoni
Dan id-dokument magħmul għal prodott imsemmi hawn fuq, li huwa skond il-provizjonijiet imsemmija d-dokumenti tal-klassi tax-
xogħol:
98/37/EC Machinery Directive
73/23/EC Low Voltage Directive (tapplika biss għal prodotti li jaħdmu bl-eletrkiu)
DK Erklæring om overensstemmelse
Vi, Trelawny SPT Limited
Erklærer hermed at under vores ene forhandling ansvar for vores forhandling/produktion af produktet
Produkt navn
Model, serie nummer
Produktionsár
For hvilket delle dokument referer, at deler i overensstemmelse med bestemmelser af følgende direktiver, normative dokumenter
og deres relevante standart:
98/37/EC Machinery directive
73/23/EC Low voltage directive
NL EENVORMIGHEIDSVERKLARING
Wij. Trelawny SPT Limited
Verklaren dat wij de volledige verantwoordelijkheid dragen voor het leveren/fabriceren van het volgende product:
Naam van het product
Type, Serienummer
Productiejaar
En verklaren dat het product waarnaar dit document verwijst eenvormig is met de voorzieningen van de volgende Richtlijn(en),
Normatieve Documenten en hun relevante Standaarden:
98/37/CE MACHINERICHTLIJN
73/23/CE LAAGSPANNINGSRICHTLIJN (uitsluitend van toepassing bij producten die elektrische stroom gebruiken)
EE TOOTE VASTAVUSE DEKLARATSIOON
Meie, Trelawny SPT Limited
Deklareerime, et vastutame jägmise varustuse/toote müügi eest
Toote nimetus
Mudel, Seeria number
Aasta toodangu
Antud dokument töendab toote vastavust järgmistele direktiivi(de)le, normatiivaktidele ja nendega samaväärsetele standarditele:
98/37/EC MASINA DIREKTIIVID
73/23/EC MADALPINGE DIREKTIIVID (Kohandatakse vaid toodetele, mis kasutavad elektrivoolu
PL Deklaracja Zgodnosci
My, Firma Trelawny SPT Limited.
oświadczamy w naszej odpowiedzialności, ze produkcja i dostawa urzctdzenia
Nazwa produkta
Model, numer seryjny
Rok produkcji
do którego ten dokument należy, jest zgodne z klauzulami nastąpujacych zarządzen i ich istotnych standartów:
98/37/EC Zarządzenie mechaniczne
73/23/EC Zarządzenie niskiego napięcia elektrycznego (Zastosowanie tylko przy urządzeniach elektrycznoych)
ES Declaración de Conformidad
Nosotros, Trelawny SPT Limited
Declaramos que bajo nuestra completa responsabilidad de Ia fabricación/suministro del producto
Nombre del Producto
Modelo, No de Serie
Año de producción
A quién este documento se refiere, está de acuerdo con lo relacionado en Ia Directriz, Normativa Documentada y sus relevantes
standards:
98/37/EC Directorio de Maquinaria
73/23/EC Directorio de Bajo Voltaje (Aplicable solamente a productos que funcionen con electricidad)
PT DECLARAÇÄO DE CONFORMIDADE CE
A empresa TRELAWNY SPT LIMITED
Declara, sob sua inteira responsabilidade, que o fornecimento/fabrico do seguinte produto:
Designaçáo do produto
Modelo, Nümero de Série
Ano de produçáo
a que esta declaraçáo se refere. está em conformidade com o preceituado nas Directivas e Normas Comunitárias abaixo indicadas:
98/37/EC DIRECTIVA DE MÁQUINAS
73/23/EC DIRECTIVA DE BAIXA VOLTAGEM (Aplicável apenas a produtos que utilzi am energia eléctrica)
FI ILMOITUSVAHVISTUS
Me. Trelawny SPT Limited
Vahvistamme tuotteiden toimittamisesta/valmistamisesta
Tuotenimi
Malli, sarjanumero
Valmisttusvuosi
Tällä todistuksella vahvistamme säädökset seuraviin ohje/ohjesiin, Yleisiin papereihin ja niihin liittyvät vaatimukset:
98/37/EC KONEISTON OHJEET
73/23/EC PIENJÄNNITE OHJEET (tarvitaan ainoastaan tuotteille jotka käyttävät sähkovoimaa)
RU CBИдETEПЬCTBO O COOTBETCTBИИ
Mьι, Trelawny SPT Limited
3aявляем, что несем полную ответственость эа поставκу/производство нижеукаэанной
продуκцим
Hаименоване изделия
Mодель, серийньιй номер
Год вьιлуска
на котоеую вьιдано настящее Cвидетельство, и которая соответствует положениям слдующей(иx) директив(ьι),
нормативньιм доκументам и относящимся к ним стандартам:
98/37/EC ДИРЕКТИВА ПО MEXAHИ3MAM
73/23/EC ДИРЕКТИВА ПО HИ3KOBOЛЬTHOMУ OЪOPУДOBAHИЮ (распространяется только на изделия с
злектропитанием)
FR DÉCLARATION DE CONFORMITÉ
Nous, soussignés Trelawny SPT Limited
déclarons que le produit sous-nommé
Nom du produit
Modèle et Numéro de Serié
Année de production
et pour lequelnous prenons entière responsabilité pour sa fourniture et manufacture, est conforme aux clauses des directives
suivantes documents norminatifs et normes qui s'y appliquent:
98/37/EC DIRECTIVE POUR LA MACHINERIE
73/23/EC DIRECTIVE POUR BAS VOLTAGE (n'est applicable qu'aux produits utilisant l'énergie électrique)
SE FÖRSÄKRAN OM ÖVERENSSTÄMMELSE
VI, TRELAWNY SPT LIMITED
FÖRKLARAR ATT VI MED ENSAMT ANSVAR ANSKAFFAT / TILLVERKAT PRODUKTEN PRODUKTNAMN
MODELL och SERlE NUMMER
Tillverkningsár
TILL VILKEN DETTA DOKUMENT HÄNVISAR ÄR I ÖVERENSSTÄMMELSE MED FÖLJANDE DIREKTIV, NORMATIVA
DOKUMENT OCH DERAS RELEVANTA STANDARDER
98/37/EC MASKINDIREKTIV
73/23/EC LÄGSTRÖMSDIREKTIV (TILLÄMPLIG PÄ ELEKTRISK DRIVNA PRODUKTER)
GR ΔΗΛΩΣΗ ΠΙΣΤΟΤΗΤΑΣ
Η εταιρεια Trelawny Spt Limited
Δηλωνει ότι έχει τη μονδικη ευθυνη ως κατασκευαστρια / προμηθευτρια του παρακατω προιοντος περιγραφη προιοντος
μοντελο, αριθμος σειρας
έτος παραγωγής
και στο οποιο αναφερεται αυτη η δηλωση, ειναι συμβατο με τις προδιαγαφες που οριϚονται στιϚ ακολουθεϚ Koινοτικες
OδηγιεϚ EλεγκτικεϚ ΔιαταξειϚ κι αλλεϚ σχετικες προδιαγραφεϚ
98/37/EC OΔHΓΙΑ ΠΕΡΙ ΜΗΧANHMATΩN
73/23/EC OΔHΓΙΑ ΠΕΡΙ XAMHΛHΣ TAΣHΣ (αφορα μονον προιοντα που λειτουργουν με ηλεκτρικο ρευμα)
SI IZJAVA O SKLADNOSTI
Trelawny SPT Limited
pod polno odgovornostjo izjavljamo, da so spodaj navedeni proizvodi, ki jih dobavljamolproizvajamo:
lme proizvoda
Model. serijska številka
Leto proizvodnje
na katere se ta dokument nanaša. proizvedeni v skladu z določili naslednjih direktiv, normativnih dokumentov in njihovih relevant-
nih standardov:
98/37/EC DIREKTIVA O STROJIH
73/23/EC DIREKTIVA O STROJIH Z NIZKO VOLTAŽO (nanaša se samo na proizvode na električni pogon)
HU MEGFELELŐSÉGI NYILATKOZAT
Mi. A "Trelawny SPT Limited" cég
Felelösségünk tudatában kijelentjük, hogy mint a termék szállitója/gyartója
Termék neve
Tipus, Sorozatszáma
Gyártási év
amelyre jelen dokumentum vonatkozik, megfelel az alábbi lrányelv(ek), lrányadó Dokumentumok elöirásainak, és az azokat
meghatározó szabvanyoknak:
98/37/EC GÉPÉSZETI IRÁNYELVEK
73/23/EC KISFESZÜLTSÉGÜ IRÁNYELVEK (Csak az elektromos meghajtásů gepeknél)
TR UYGUNLUK BEYANI
Trelawny SPT Limited
AÞaöýdaki, üretim ve tedarikinden tek baÞýna sorumlu olduöu ürünün
Ürün ady
Modei/Seri no
Üretim yili
bu belgenin ilgili olduöu apaöýdaki yönetmeliklerin, norm belgelerinin ve ilgili standartlarýnýn koÞullarýna uygun olduöunu beyan
eder:
98/37/EC MAKŶNALAR YÖNETMELŶDŶ
73/23/EC DÜÞÜK GERŶLŶM YÖNETMELŶDŶ (Yalnýýz elektrikle çalyÞan ürünlerde geçerlidir)
IT DICHIARAZIONE Dl CONFORMITA
La Società Trelawny SPT Limited
Dichiara, sotto Ia propria responsabilità, che Ia fornitura / produzione del prodotto
Nome prodotto
Modello, codice
Anno di produzione
a cui si riferisce tale documento è conforme aile seguenti Direttive, ai documenti della Normativa ed ai relativi standard:
98/37/EC DIRETTIVA SULLE APPARECCHIATURE
73/23/EC DIRETTIVA SUL BASSO VOLTAGGIO (applicabile esclusivamente peri prodotti che utilizzano energia elettrica)
DECLARATION OF CONFORMITY

PAGE 6
TFS230 Floor Stripper
DO -
Wear Personal Protective Equipment (PPE) including safety
goggles, footwear, ear defenders and gloves. In some
environments it will be necessary to wear face masks or
breathing apparatus.
Be aware that this tool can create dust and ying debris.
Be aware of others working around you.
Keep hands, feet and clothing away from moving parts, there
exists a risk of pinch, crush or shear injury.
All points are highlighted with symbols (see page 15)
Store this tool in a secure and dry environment.
Ensure that the workplace is well ventilated. Avoid using a fuel
powered generator in an enclosed area, since engine exhaust
gases are poisonous.
DO NOT -
Intervene into the cutting zone when in operation.
Leave unattended on uneven surfaces - check wheels
for safety.
Allow the tool to run unattended.
Modify this tool in any way, as this will invalidate the
warranty and could lead to serious injury.
Use this tool in potentially explosive environments.
Use petrol (gasoline), thinners or any other high ash
point solvent to clean the tool.
Disassemble or repair unless Trelawny trained.
Return to base repair advised.
Repetitively restart motors, this will potentially damage the
motor. Leave a Minimum 15 seconds duration between starts
and no more than 4 restarts in a minute.
WEAR SAFETY BOOTS, FACE MASK, SHATTERPROOF
GLASSES, HELMET, GLOVES, and any other personal
protective equipment required for the working conditions.
Avoid loose clothing; this may become trapped in moving
parts and cause serious injury.
ENSURE THAT THE WORKPLACE IS WELL VENTILATED.
DO NOT OPERATE ELECTRIC EQUIPMENT IN WET
CONDITIONS.
CAUTION THIS MACHINE IS HEAVY.
It weighs 48kg / 105lbs. Do not lift this machine manually
assisted lift required.
BEWARE OF MOVING BLADE.
Serious injury could occur if the stripper blade is brought into
contact with body parts during operation.
INSPECT MACHINE FOR DAMAGE PRIOR TO USING.
Ensure all graphic warnings, cables and electricals are visibly
undamaged and intact prior to use.
BEWARE OF HOT SURFACES
Use appropriate PPE for protection.
REMOVE BLADE WHEN IN TRANSIT.
PLACE IN LOW POSITION FOR TRANSIT.
HANDLING OF THE BLADE.
The blade is sharp at all times, use of gloves is mandated. Do
not lift the machine by the blade. If the blade becomes lodged
use a gripping tool, such as pliers to dislodge it. DO NOT
attempt to remove it by hand.
Thank you for your purchase of the Trelawny TFS230 Floor
stripper. Before operating the TFS230 this manual must be
read and understood by the operator, if in any doubt ask your
supervisor before using this equipment. Failure to follow these
instructions could result in damage to the TFS230 and/or
personal injury.
Trelawny SPT Ltd disclaims all responsibility for damage to
persons or objects arising as a consequence of incorrect
handling of the tool, failure to inspect the tool prior to starting
work for damage or other faults that may inuence the
operation or safe working of the tool, or failure to follow the
safety regulations listed or applicable to the job site.
The machine is primarily designed for the removal of bonded
carpet, vinyl, linoleum, cork, and other oor covering. It can be
used for removal of compacted soil from forklift truck areas or
solidied printing ink etc.
Operators should be familiar with the data given in the
specication section. Please keep these instructions in a safe
and accessible place.
GENERAL Information
WARNING! Before operating or performing maintenance
the TFS230 Floor Stripper this manual must be read and
understood. If in any doubt, ask your supervisor before
using this equipment.
SAFETY
WARNING! Always observe safe-working practices and
local safety regulations at all times.

www.trelawny.co.uk
Risk of Hand-arm Vibration injury
Assembly Instructions
These tools may cause Hand-arm Vibration Syndrome injury if
their use is not adequately managed.
We advise you to carry out a risk assessment and to
implement measures such as limiting exposure time [i.e.
actual trigger time, not total time at work], job rotation,
ensuring the tools are used correctly, ensuring the tools are
maintained according to our recommendations, and ensuring
that the operators wear personal protective equipment (PPE)
particularly gloves and clothing to keep them warm and dry.
Employers should consider setting up a programme of health
surveillance to establish a benchmark for each operator and
to detect early symptoms of vibration injury.
We are not aware of any PPE that provides protection against
vibration injury by attenuating vibration emissions.
See ‘Specications’ section for vibration emission data.
Further advice is available from our Technical Department.
We strongly advise you to visit the Health & Safety Executive
website http://www.hse.gov.uk/vibration. This site provides
excellent advice and information on HAV and currently,
includes a Hand-arm Vibration Exposure Calculator that is
easy to use to work out the daily vibration exposure for each of
your operators.
There are three main parts:
• Main body
• Lower handle
• Upper handle
STEP 1
Fit lower handle to main body with
4 bolts and washers. Fit all four bolts
loosely rst, then tighten fully.
STEP 2
Pull the knob on lower handle and slide
upper handle into lower handle tube.
Secure by turning knob until upper
handle is securely clamped in place.
FOR HAZARD, RISK, PPE SYMBOL DEFINITIONS
SEE TABLE ON PAGE 15
2
1
1

PAGE 8
TFS230 Floor Stripper
STARTING - ELECTRIC MOTORS
PRE START CHECKS (DAILY)
Inspect the supply cable; Check that no damage has been
caused to the outer casing and that there are no exposed or
loose wires. Obtain the assistance of an electrician if a fault
is found. Do not use the machine until it has been rectied.
Check that the cable is not running across sharp or jagged
edges and that it is not in contact with any liquid.
STEP 1
Adjust stripping angle and handle height as required.
STEP 2
Plug the supply cable into the inlet plug, ensure blade
is free to move, and clear of any ooring material.
STEP 3
Press the green button and the motor will start.
STEP 4
To stop press the red button.
STEP 5: If the isolator will not turn on, unplug the supply cable,
and press the small white button on the starter box side, this
resets the overload in the motor breaker, then plug the supply
cable back in to operate.
IMPORTANT! Allow 15 seconds after shutting o before
turning the motor on again.
- Check all bolts and screws for tightness. Ensure that
all ttings are secure.
- Check condition of blade, blade attachment, blade
mechanism and replace components as required.
Electric Models
The TFS230 is supplied with a specially commissioned electric
motors and starter box assembly. Each unit is fully tested
and set according to the manufacture’s specications. In the
event of malfunction on a new machine, the owner should rst
check that the power supply on site is suitable and adequate.
All cables should be fully uncoiled and never left wrapped
around cable reels or tied in loops. The starter box is tted
with a safety feature to protect the motor and from damage.
The starter boxes are pre-set and under no circumstances
should they be tampered with, stripped down or adjusted, this
will invalidate the warranty. The starter control box must only
be accessed by a fully trained person or electrically qualied
engineer.
110v Motor
Use a centre tap transformer with a continuous rated output
of 5.0KVA and must be a 230v 20amp supply. Do not add an
extension lead to the transformer input. Do not use a 230v
13amp domestic supply. The motor requires the minimum of a
32amp, 110v power supply. The 110v machine requires the use
of 4mm2extension cable up to a maximum of 20 metres, as
it draws a signicant operating current. The use of 2.5mm2for
110v machines is not recommended and can cause operating
problems, particularly in conjunction with poor supplies,
where excessive voltage drops will be encountered and
damage to the machine may occur.
230v Motor
Take particular care when using 230v Machines, ensure that
the electrical supply is earthed, and that breakers and fuses
are correct for the loading. The 230v motor requires the
minimum of a 13amp, 230v power supply. Always use the
shortest possible length of extension cable. To avoid Voltage
drop Trelawny recommends a maximum cable length of 40m
with a core wire size of 4mm2cross sectional area.
1
2
3
4
5

www.trelawny.co.uk
Handle adjustment
Adjust handle up and down by unscrewing
the knob and pulling it out slightly and
sliding the upper handle to the desired
height. Secure it after you set the
handle height.
STEP 1
Loosen the knob by following the
instructions and pull.
STEP 2
Set the handle height to a desired height.
STEP 3
Secure the knob after setting height by
following the instructions.
1
2
3
Blade Replacement
Loosen the three Allen screws on top of
the blade holder which clamp the blade in
position, remove blade holder and replace
the blade. Replace the holder, replace and
tighten the retaining screws.
STEP 1
Ensure machine is switched o and
isolated from power supply.
STEP 2
Loosen the three Allen screws on top
of the blade holder. (DO NOT REMOVE
COMPLETELY)
STEP 3
Remove blade holder.
STEP 4
Replace blade.
STEP 5
Secure the blade holder back into place
and tighten screws.
CAUTION: BLADES ARE SHARP!
Observe PPE & safety precautions
when changing blades.
1
2
4
5
3

PAGE 10
TFS230 Floor Stripper
STEP 1
Loosen (do not remove) the T-handle on
the left side of the TFS230, located above
the back left hand wheel.
STEP 2
Lift handle upwards (rear wheels should
remain on the ground).
STEP 3
When you reach the required angle
tighten the T-handle rmly.
NOTE: use the minimum angle required for
your ooring material/application.
Blade Angle Adjustment
2
1
3
PPE and warning hazard symbols explanation
SYMBOL / WARNING DESCRIPTION
Always read the manual.
Wear protective glasses.
Wear ear defenders.
Wear protective shoes.
Wear protective gloves.
SYMBOL / WARNING DESCRIPTION
Caution assisted lift only.
Caution crush point.
Caution pinch point.
Danger 110V.
Danger 230V.
CAUTION
ASSISTED
LIFT ONLY
CAUTION
CRUSH POINT
CAUTION
PINCH POINT
DANGER 110V
ISOLATE BEFORE
REMOVING COVER
DANGER 230V
ISOLATE BEFORE
REMOVING COVER

www.trelawny.co.uk
MACHINE OPERATION
Maintenance and Machine Storage
1. Before starting the motor, increase the “angle of attack” of
the blade to the desired level until the blade makes contact
with the underside of the surface to be stripped. Ensure the
blade is NOT in contact with the target surface before starting
the machine.
2. Manually remove any nails, studs, pins, rebar etc. from
the area to be stripped before starting work. Attempting to
strip with such items in place will damage the blade and/or
machine.
3. For large area vinyl oors or large carpet areas use a knife
score the material into strips of approximately same with as
TFS blade before starting work.
4. Complete a small area observing the performance; angle of
attack, inspect the nish produced.
DO NOT ADJUST THE BLADE ANGLE WHILST THE MACHINE
IS IN OPERATION.
5. Remember let the machine do the work before exerting
excess pressure through the handle or foot plate. Light passes
are quicker and more cost eective that one slow heavy
pass. Tests have proved conclusively that heavy downward
pressure reduces blade life and increases risk of “sticking”
under the target surface by over 50%.
6. Avoid metal objects lodged in the oor as this will cause
damage to the machine.
DO NOT use the above method if the oor is wet or damp due
to the inherent danger of the water ingress.
NOTE: Electrical motors and switches are not totally
waterproof; but are protected to IP44; take special care to
protect them from water to ensure safety.
7. The TFS230 is designed to be used in a forward motion;
the oscillation of the blade also helps with the operation. The
operator can vary the speed of travel and angle of adjustment
to determine the nal nish.
8. In an emergency, when the blade must be lifted quickly
from the work surface, it is not necessary to turn o the
machine, simply tilt backwards on the handlebar to lift the
front wheels o the oor.
9. DO NOT move the machine around the work area tilted to
the rear, with the blade in the air, without a blade protector in
place. The risk of shin injury to persons in the workspace is
high.
10. DO NOT leave the machine connected and unattended
at any time. Ensure the blade protector is in place at all times
when not in use.
11. PPE must be worn at all times.
- After use, clean the machine to remove all build up of dust
and surface residues. If using a hosepipe or pressure washer
take care not to direct water at electrical components and
switches.
NOTE: Motors and switches are not waterproof.
- Daily check the drive elements for build up of deposits and
any trapped debris etc. Check the underside for damage.
- Serious damage could result to the drive shaft, bearings and
drive motor if the blade mechanism is obstructed.
WARNING: Never operate the TFS230 without the machine
being at on the ground. All fastenings should be checked
daily for tightness and tension.
Check the individual motor manufactures instructions for
details on their service recommendations.
Short period storage: up to 3 months
- Clean outside of machine, inspect the moving parts for wear;
replace any worn parts as required.
- Remove any build up of material from inside the
mechanical area.
- Cover the machine to protect it: Store the machine in a dry
place. Be sure to check security of all fastenings after any
lay up period. See also motor manufactures operation and
maintenance instruction book.
Long period storage: over 3 months
- Clean the outside of the machine, inspect for wear; replace
any worn parts as required.
- Remove any build up of material from inside the
mechanical area.
- Cover the machine to protect it: Store the machine in a
dry place.
- After any long lay up period be sure to check the security
of all fastenings.
- Ensure blade is removed and stored safely whenever the
machine is transported.

PAGE 12
TFS230 Floor Stripper
EXPLODED VIEW
C
40
42
38
12
52
53
2
38
44
43
15
47 46
1
3
22
23
23
24
21
20
17
56
57
45
23
24
54
59
26
15
27
11
10
9
8
6
7
16
15
13
5
14
13
12
25
14
18
19
48 60
58
29
39
41 4
62
63
61
63
64
32
33
31
30
28
38
34
33
37
35
36
65
DETAIL C
50
49
51
55
TABLE 1: ELECTRICAL ENCLOSURE
54
CONFIGURATION TABLE
Machine
Description
Electrical Enclosure
Assembly
323.2402 TFS - 110V 990.0033
323.2404
TFS - 230V 990.0034

www.trelawny.co.uk
Power signal flow direction
through the circuit
2.5sqmm Internal Single core cable
size
2.5sqmm
3C Arm/Power Cable size
Loop Connection
~AC Input (Motor)
Loop Cable size
(1.5sqmm)
Power signal flow direction
through the circuit
2.5sqmm Internal Single core cable
size
2.5sqmm
3C Arm/Power Cable size
Loop Connection
~AC Input (Motor)
Loop Cable size
(1.5sqmm)
WIRING DIAGRAMS
110VAC 16A
Inlet Plug
Line
2.5sqmm
Line 2.5sqmm
Earth
Line
Load
Thermal
Breaker
2.5sqmm
C
C C2
C2
E-Stop
2.5sqmm
6(14) 8(11) 1(A1)
2(24) 4(21) 0(A2) MOTOR
110V Wiring
2.5sqmm
C
C
C1
C1
2.5sqmm
2.5sqmm
2.5sqmm
2.5sqmm
Start
2.5sqmm 3C
D
Power Relay
A
B
C
E
2.5sqmm
TFS 110V Wiring Diagram
~
~
230VAC 16A
Inlet Plug
Line
2.5sqmm
Neutral 2.5sqmm
Earth
Line
Load
Thermal
Breaker
2.5sqmm
C
C C2
C2
E-Stop
2.5sqmm
6(14) 8(11) 1(A1)
2(24) 4(21) 0(A2) MOTOR
230V Wiring
2.5sqmm
C
C
C1
C1
2.5sqmm
2.5sqmm
2.5sqmm
2.5sqmm
Start
2.5sqmm 3C
D
Power Relay
A
B
C
E
2.5sqmm
TFS 230V Wiring Diagram
~
~

PAGE 14
TFS230 Floor Stripper
Parts List TFS230
ITEM NO. PART NO. DESCRIPTION
1 990.0011 TFS - Chassis Metalwork Assy 1
2 990.0035 TFS - Stripper Arm Wear Strip Assembly 1
3 853.0830 M8 x 30mm CSK Socket Head Screw 2
4 875.1270 M10 Square Nut (DIN 557) 2
5 990.0014 TFS - Rear Wheel Linkage Assembly 1
6 350.9121 Wheel 200 GRSH 2
7 875.1195 Shoulder Washer 20mm X 21.9mm X 6mm - Black Nylon
8 812.1001 20mm Plain Washer 2
9 814.1020 Circlip (Ext.) 20mm x 1.2 2
10 990.1041 TFS - Rear Wheel Height Linkage LH 1
11 990.1075 TFS - Rear Wheel Height Linkage RH 1
12 875.1187 M8 (10mm) X 16mm Socket Shoulder Screw 4
13 812.0710 M10 Washer zinc plated 4
14 875.1193 Shoulder Washer 10.2mm X 12.5mm X 2.5mm - Black
15 812.1080 M8 Plain Washer 9
16 824.0800 M8 Nylock Nut 2
17 990.0020 TFS - Height Adustment Threaded Tube Metalwork A
18 812.2010 M10 Mudguard Washer
19 857.1010 Wing Screw M10 x 40mm 1
20 875.1216 M16 x 30 x 3.0mm Form A Nylon Washers, Black 1
21 875.1194 Shoulder Washer 14.2mm X 17.8mm X 2mm - Black Ny
22 875.1293 M4 x 30mm Hex Head Machine Screw, Mild Steel, Bl
23 812.1040 Washer, M4 6
24 875.1215 M4 Nyloc Hex Nut 5
25 990.0024 TFS - Central Handle Upper Assy 1
26 990.0019 TFS - Central Handle Mid Sleeve Assy 1
27 875.1219 M8 x 25mm Hex Socket Button Screw, Black 4
28 990.0017 TFS - Stripping Head Metalwork Assembly 1
29 323.3509 A 230mm Blade TFS 230 1
30 990.1059 TFS - Stripping Head Blade Plate Upper 1
31 875.1199 M8 x 20 Countersunk Machine Screw
32 875.1290 M6 x 45mm Hex Head Bolt 4
33 812.1060 M6 Plain Washer 8
34 824.0600 M6 Nyloc Nut 4
35 875.1226 Compression Spring
36 875.1198 Disc Bearing 1
37 990.0037 TFS - Stripper Arm HK Bearing Housing Assembly 1
38 875.1188 Polymer Flanged Bush 10mm x 12mm x 7mm
39 875.1287 M8 Hex Nut (Flanged) 2
40 875.1248 Polymer Thrust Washer 10mm x 18mm x 1.0mm
41 875.1288 Shim Washer, Carbon Steel 10mm x 16mm x 1.0mm 2
42 990.1052 TFS - Stripping Head Pivot Arm 1
43 990.1051 TFS - Stripper Arm Brace Bar 1
44 853.0830 M8 x 30mm Socket Head Screw
45 875.1283 Electric Motor 1.1kW, (Dual Voltage)
46 831.0825 M8 x 25mm Hex Head Machine Screw 4
47 811.1008 M8 Shakeproof Washer 1
48 831.0820 M8 x 20mm Hex Head Machine Screw 1
49 875.1242 Disc Spring - 25.5mm x 39.6mm x 0.5mm
50 875.1303 M24 Pin Washer, Steel
51 990.1060 TFS - Stripper Arm Eccentric Bushing 1
52 875.1246 Thrust Washer AS
53 875.1196 M8 x 60mm x 4.0mm Penny Washer 1
54 990.0033 TFS - Emergency Stop Enclosure Assembly
55 875.1280 Shim Washer, Carbon Steel 35mm x 45mm x 1mm 2
56 990.1093 TFS - Motor Shield
57 852.0812 M8 x 12mm Button Head Machine Screw 4
58 320.9226 M8 Full Hex Nut 4
59 323.9104 Threaded Clamping Spring Plunger 1
60 875.1300 Threadlock - Medium Strength
61 320.9120 TFP200 Front Wheel 2
62 990.1076 TFS - Front Wheel Stub Axle
63 812.0712 M12 Washer zinc plated
64 875.1295 Single Turn Spiral Retaing Ring - 12mm External
65 805.0501 Allen Key 5mm Hex 1

www.trelawny.co.uk
Technical specication
Length x Width x Height (inc extended handle and wheels) 100mm x 86mm x 35mm 39.5” x 34” x 13.5”
Blade Width 230mm 7”
Weight 48kg 105lbs
Electric Motors
Power 1.1Kw 1.5hp
RPM 1425
Voltage / Amperage / Frequency 115VAC / 17Amp / 50Hz 230VAC / 8.5Amp / 50Hz
Noise Emission (accordance with EN ISO 15744: 2008 and ISO 3744:2010)
Noise Level:
lpa 82dpa
Vibration Emission (measured in accordance with EN ISO 20643:2005)
Vibration (AEQ) at handle: (k**) 11.5m/s2 (k - 0% +40%)
(k**) Equals the factor of uncertainty, which allows for variations in measurement and production. Vibration Data gures are tri-axial, which gives the total vibration
emission. Because of various factors, the range of vibration emission during intended use can vary. The vibration is dependent on the task, the operators grip, and
feed force employed etc.
TROUBLESHOOTING
FAU LT POSSIBLE CAUSE ACTION
Electric motor will not start.
Insucient supply voltage.
Check supply voltage with within specications.
Check transformer (if present) is of recommended specication and
functioning correctly.
Check transformer (if present) thermal trip hasn’t activated. Wait and reset if
applicable.
Check Cable extension length is within specied limits and/or cross section
is equal or over size. Refer to Manual
Stripping head jammed. Ensure machine is clear of all ooring and other media before starting.
Thermal safety trip has activated.
Wait until machine has cooled down (approx 30mins), press the reset button
on the side of the electrical enclosure, then attempt restart. If the issue
persists, contact customer support.
Electric motor stops during use.
Motor stalled. Ensure machine is clear of all ooring and other media before restarting. If
the issue persists, contact customer support.
Thermal safety trip has activated.
Wait until machine has cooled down (approx 30mins), press the reset button
on the side of the Electrical Enclosure, then attempt restart. If the issue
persists, contact customer support.
Stripping head not removing
material eectively
Blade blunt/damaged/clogged. Inspect stripping blade. Carefully clean or replace blade if required.
Blade incorrectly installed. Check blade installation for squareness & tightness. Blade should have bevel
facing up for most ooring media.
Incorrect/inecient stripping head angle. Adjust stripping angle as required. Use the minimum angle possible for
media to be removed.
Stripping sheet materials, such as vinyl or
carpet.
Use a knife to score the material into strips of approximately same with as
TFS230 blade before starting work.
Eccentric bearing failure. Replace.
Unexpected noise/rattling.
Motor/drivetrain wear. Switch o & Isolate power to machine. Carefully inspect motor & free-moving
parts.
Worn or loose xings/fasteners. Switch o & isolate power to machine. Carefully inspect xings, pivots etc.
tighten any loose fasteners.

PAGE 16
TFS230 Floor Stripper
Notes

www.trelawny.co.uk
Notes

PAGE 18
TFS230 Floor Stripper
Notes

www.trelawny.co.uk
Machinery Directive Information:
This tool has been designed and produced in accordance with the following directives:
2006/42/EC Machinery Directive
If your company has any problem with our products or would like to discuss the possibility of an improvement
being made to them, then please do not hesitate to contact us. Your comments are both important and
appreciated. All rights reserved. Any unauthorised use or copying of the contents or part thereof is prohibited. This
applies to trademarks, model denominations, part numbers and drawings. Use only genuine Trelawny spares.
The use of non-Trelawny spare parts invalidates the warranty.

www.trelawny.co.uk
32
Trelawny SPT Limited
Trelawny House, 13 Highdown Road, Sydenham Industrial Estate,
Leamington Spa, Warwickshire, CV31 1XT, United Kingdom
Telephone: [phone] Fax: [phone] Email: [e-mail]
Website: www.trelawny.co.uk
Dealer Stamp:
Manual Part Number:
735.5200
DEALER STAMP:
need to contact us?
Trelawny SPT Limited
Trelawny House, 13 Highdown Road, Sydenham Industrial Estate,
Leamington Spa, Warwickshire, CV31 1XT, United Kingdom
Manual Part Number:
735.5230
Telephone: [phone] Fax: [phone]
Email: [e-mail]
Website: www.trelawny.co.uk
www.trelawny.co.uk
32
Trelawny SPT Limited
Trelawny House, 13 Highdown Road, Sydenham Industrial Estate,
Leamington Spa, Warwickshire, CV31 1XT, United Kingdom
Telephone: [phone] Fax: [phone] Email: [e-mail]
Website: www.trelawny.co.uk
Dealer Stamp:
Manual Part Number:
735.5200