trendmedic TM-2000 User manual

Copyright © 2018 trendmedic.de. All rights reserved.
Model: TM-2000 .

Copyright © 2018 trendmedic.de. All rights reserved.
TABLE OF CONTENTS
Introduction----------------------------------------------------------------------------------------
Correct Measurement---------------------------------------------------------------------------
Description of Parts------------------------------------------------------------------------------
Power Supply--------------------------------------------------------------------------------------
Operation-------------------------------------------------------------------------------------------
Accessories----------------------------------------------------------------------------------------
Error and Troubles-------------------------------------------------------------------------------
Important Notes-----------------------------------------------------------------------------------
Specifications--------------------------------------------------------------------------------------
Calibration and Record--------------------------------------------------------------------------
Precautions-----------------------------------------------------------------------------------------
Distribution Contact ------------------------------------------------------------------------------

Copyright © 2018 trendmedic.de. All rights reserved.
Introduction
The device is intended to measure alcohol in the human breath. Measurements obtained by
this device are used in the diagnosis of alcohol intoxication.
The accuracy of this device has been established at a Blood Alcohol Concentration of 0.00,
0.20, 0.50 and 0.80‰BAC.
Preparation for Correct Measurement
•Before testing, wait at least 15 minutes after your last drinking.
•Only use the device in a temperature 5°C ~ 45°C or 40°F ~ 114°F.
Description of parts: LCD screen, Mouthpiece, Test button, Rating label, Battery cover
Power Supply
•Slide back the battery cover on the back of the device.
•Insert 2 piece AAA battery, making sure that the “+/-“symbols are correctly.
•

Copyright © 2018 trendmedic.de. All rights reserved.
•If the power is too low, the unit may display a battery symbol “ “and the device may
not use correctly. You need to change a new battery.
Operation
(Test mode)
•Insert one of the mouthpieces into the ‘blow in’ hole.
•Press and hold the TEST button until power on. Release it after power on.
•The WAIT displays on the screen and countdown 10, 9, and 8… to zero.
•The BLOW displays on the screen, and displays “C” with flashing. Take a deep breath,
blowing steady into the mouthpiece until beeping stops (about 6 seconds).

Copyright © 2018 trendmedic.de. All rights reserved.
•The device displays “WAIT” and flashing the “0” on the screen.
•Your test result will be displayed on the screen for 20 seconds.
•Your test result will be changed the color with beeping sound if above alarm limit.
•It will show error when incorrect blowing. Refer to the chapter of the “Errors and
Troubles” in detail. The device will be turned off after indicated error.
Accessories
•5 Mouthpieces
•Manual
•Soft carry bag
Important notes
•Before testing, wait at least 15 minutes after your last drinking.

Copyright © 2018 trendmedic.de. All rights reserved.
•The blowing time must be enough until beeping stops.
•It may show ERR (error) if none, interrupt or shorter blowing.
•Recalibration interval suggest: 12 months or 800 tested times
•Never store the device in a corrosive gas room.
•Never store the device under sun exposure area.
•Avoid dropping or subjecting the device to a strong shock.
Errors or Troubles
Error
message
or Troubles
Description
Remarks
No display
-Press and hold the TEST button until power on.
-Check the battery and use alkaline battery only
Auto Off
-Low battery
-Over the period of test stage
Err
-Blowing unsteady or interrupt
-Blowing less than 6 seconds
-Blowing flow too weak
-No blow during BLOW mode.
-Low battery indication
-Need to change new battery
-Use alkaline battery only
Alarm sound
-During the blowing mode
-Error message indication
-Above alcohol set point
-Above tested times
HI
-The blood alcohol content above the display range.
Specifications
Electrochemical sensor (Fuel Cell Sensor)
Blowing time about 6 seconds
Blowing flow about 10L/min
Blowing flow interrupt detection
Test counter to display the operated number when power on
4 digits display with status and backlight
Display range: 0.000-3.000‰
Show “HI” if above the display range
Accuracy: +/-0.05‰ at 0.50‰
5 replaceable mouthpieces
Warm up time: 10 seconds
Testing Time: 10 seconds

Copyright © 2018 trendmedic.de. All rights reserved.
Repeat test: less than 30 seconds.
Audible sound and change LCD color if above alarm limit
Power supply: 2 pcs AAA 1.5V alkaline battery
Battery for standard testing is about 800 times
Low battery indication and auto power off function
Operation: 5°C ~ 45°C or 40°F ~ 114°F
Store: 0ºC ~ 50ºC or 32°F~122°F
Size: 105x55x23mm
Calibration and Record
•You should have your alcohol tester calibrated every 12 months or 800 tested times.
Failure to do so may cause your readings to be inaccurate.
Calibration Record
Date First
Used
Serial Number
#
Calibration Date
Remarks
Recalibration by
Precautions
•Your blood alcohol content (BAC) may change some minutes later.
•You should have your alcohol tester calibrated every 12 months or 800 tests. Failure to
do so may cause your readings to be inaccurate.
•Do not use this device to determine if you can drive.
•You cannot use the test results of device in court of law.
•You cannot use the test result of device against police’s unit.
Distribution Contact
Trendmedic
Nonnenwaldstr. 26A
D-82377 Penzberg
Germany
Phone: [phone]
E-Mail: [email protected]
Web: www.trendmedic.de