TRENDnet TEW-OA14DK User manual

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEW-OA14DK
Version 01.14.05
14dBi Directional Outdoor Antenna
Quick Installation Guide
Antenne extérieure directionnelle 14dBi
Guide d'installation rapide
Direktionale 14dBi-Außenantenne
Kurzanleitung zur Installation
Guía de instalación rápida de
la antena exterior direccional 14dBi

Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
10
11
1. Prepare for Installation ......................................................................
2. Product Detail .....................................................................................
3. Hardware Installation ........................................................................
4. Diagram .............................................................................................

Thank you for purchasing the TRENDnet TEW-OA14DK 14dBi Directional
Outdoor Antenna.
This guide will help you set up your Directional Outdoor Antenna. Following
the installations should be quick and easy. If you run into problems, please
refer to the Troubleshooting section. If you need further technical support,
please visit www.TRENDNET.com or call technical support by phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
TEW-OA14DK
Quick Installation Guide
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TEW-OA14DK
Version 01.14.05
14dBi Directional Outdoor Antenna
Quick Installation Guide
Antenne extérieure directionnelle 14dBi
Guide d'installation rapide
Direktionale 14dBi-Außenantenne
Kurzanleitung zur Installation
Guía de instalación rápida de
la antena exterior direccional 14dBi

2
2. Product Detail
The Directional Outdoor Antenna has two holes to install the mounting brackets
and a connector for your outdoor/indoor Wi-Fi Access Point.
English

3
3. Hardware Installation
For your reference, please see the attached diagram to guide you in mounting
your TEW-OA14DK.
1. Read through these instructions to get an idea of the process.
2. Open the hardware bags carefully and put the hardware in separate groups.
If the hardware is pre-assembled, please disassemble it and place them
together in one group.
3. Use the two M8 x 12 screws (4) and M8 spring washers (3) to mount one of
the M-Type Stands (2) to the TEW-OA14DK
English
Wall Mounting

4English
4. Securely mount the Main Stand (13) on the wall with two tapping screws
(14). Use the Plastic Wall Anchors (15) when necessary.
5. Assemble the other M-Type Stand (2) and the Triangle Stand (12) with two
M8 x 16 screws (9), four M8 washers (6), and two M8 nuts (8).

5English
6. Install the assembly in step 5(the other M-Type Stand and the Triangle
Stand) to the assembly in step 4 (the Main Stand connected to the wall) with
four M6 x 12 screws (10) and four M6 washers (11). Do not tighten the
screws, so you can rotate the Triangle Stand along the Main Stand's curved
slots.
7. Connect the assembly in step 3 (The TEW-OA14DK with the attachedType
Stand) to the assembly in step 6 (the other M-Type Stand, the Triangle
Stand, and the Main Stand) with M8 x 110 screw (7), steel tube (5), M8
Spring Washer (3), M8 washer (6), and install the M8 nut (8) on the M8 x 110
screw (7) loosely (loose enough for you to adjust the antenna angle).

8. Adjust the antenna angles and then tighten all the nuts/bolts. Be careful not
to over tighten the nuts and bolts.
Your hardware installation is now complete.
6English

7English
If you are mounting the antenna on the pole, you will need to use the Clamp
Blocks, the long bolts, and the washers (instead of the Main Stand and the
Triangle Stand). The blocks, the bolts, and the washers are not shown in the
attached diagram.
1. Read through these instructions to get an idea of the process.
2. Open the hardware bags carefully and put the hardware in separate groups.
If the hardware is pre-assembled, please disassemble it and place them
together in one group.
3. Use the two M8 x 12 screws (4) and M8 spring washers (3) to mount one of
the M-Type Stands (2) to the TEW-OA14DK.
Pole mounting

8English
4. Connect the assembly in step 3 (The TEW-OA14DK with the attached
Type Stand) to the other M-Type Stand with M8 x 110 screw (7), steel tube
(5), M8 Spring Washer (3), M8 washer (6), and install the M8 nut (8) on the
M8 x 110 screw (7) loosely (loose enough for you to adjust the antenna
angle).
5. Place the two Clamp blocks around a pole (5 cm diameter pole
recommended) and insert the long bolts with the Clamp block nuts as shown
below.