TRENDnet TW100-BRV204 SHEETS User manual

Copyright ©2004. TRENDware International, Inc.All Rights Reserved.
TRENDnet
TRENDware, USA
What's Next in Networking
Version 06.04.04
Cable/DSL VPN Firewall Router
Quick Installation Guide
Guide d'installation rapide pour le
Routeur Câble/DSL VPN avec Firewall
Schnell Anleitung
DSL/Kabel VPN Firewall Router
Guía de Instalación Rápida del
Enrutador Firewall VPN Cable/DSL
TW100-BRV204

Table of Contents
English ......................................................................................................
Français .....................................................................................................
Deutsch .....................................................................................................
Español .....................................................................................................
Troubleshooting ........................................................................................
1
1
3
4
10
15
15
29
44
16
30
45
17
24
31
38
46
53
29
44
59
1. Prepare for Installation ......................................................................
2. Install Hardware ................................................................................
3. Configure the computer's TCP/IP Settings ........................................
4. Configure the Router .........................................................................
1. Préparation de l'installation ...............................................................
2. Installation du matériel ......................................................................
3. Configuration des paramètres TCP/IP ..............................................
4. Configuration du routeur ...................................................................
1. Vorbereitung der Installation .............................................................
2. Installation der Hardware ..................................................................
3. Konfiguration der TCP/IP-Einstellungen des Computers ..................
4. Konfiguration des Routers .................................................................
1. Preparación para la instalación .........................................................
2. Instalación del Hardware ...................................................................
3. Configuración de los parámetros TCP/IP del PC ..............................
4. Configuración del enrutado ..............................................................

Thank you for purchasing the TW100-BRV204. This router will allow you to
securely share your Internet connection, files, and other resources with multiple
users.
This guide will help you set up and configure your router. Following the
installation instructions should be quick and easy. If you run into problems,
please refer to the Troubleshooting section or the more detailed installation
procedures on the User's Guide. If you need further technical support, please
visit www.trendnet.com or call by phone.
Verify Equipment
Before installing the router you should have a:
1. Cable/DSL Modem with an Ethernet Port Set-up
2. Working Internet account
3. Web Browser such as Internet Explorer (5.0 or higher) or
Netscape Navigator (4.7 or higher)
4. RJ-45 Network Cable for each computer connected to the router.
5.TCP/IP protocol installed on computer(s)
6.Computers with "Client for Microsoft Networks" installed
Verify Package Contents
Please make sure you have everything in the box:
1
TW100-BRV204
CD-ROM Quick Installation Guide
AC Power Adapter 1.5 Meter Cable
English
1. Prepare for Installation
English QIG
TRENDnet
TRENDware,USA
What's Next in Networking
Version 06.04.04
Cable/DSL VPN Firewall Router
Quick Installation Guide
Guide d'installation rapide pour le
Routeur Câble/DSL VPN avec Firewall
Schnell Anleitung
DSL/Kabel VPN Firewall Router
Guía de Instalación Rápida del
Enrutador Firewall VPN Cable/DSL
TE100-BRV204

2
Collect Internet Service Provider (ISP) Information
During the installation of your router the Set-Up Wizard will ask you for specific
Internet Service Provider ISP information you should have been provided from
your ISP to set up your Cable or DSL connection. The information is different
based on your type of Internet Connection. Please verify your Internet
Connection type and ensure you have the following information:
Dynamic IP Cable Connection
Nothing required. IP address will automatically be assigned by the ISP.
Static or Fixed IP Cable Connection
Internet IP Address:____.____.____.____
Subnet Mask: ____. ____. ____. _____
Gateway IP Address:____.____.____._____
Primary DNS:____.____._____.______
Secondary DNS:_____._____._____.____
PPPoE DSL Connection
Login Name:______________
Password:________________
PPTP DSL Connection
Login Name:_______________
Password:_________________
MAC Address Cable Connection
Your ISP's Registered MAC Address for your Internet
Account:___.____.____.____ .____.____
(The MAC Address is normally associated with the Cable/DSL modem
or the Network Card in the PC)
(eg. 215.24.24.129)
(eg. 00-0E-FF-04-CC-EE)
English

3
2. Install Hardware
32
TW100-BRV204
POWER
1. Turn off your Cable/DSL Modem, Router, and PC.
2. Connect one RJ-45 network cable from the Modem's Ethernet port to the
Router's WAN port.
3. Connect a different RJ-45 network cable from one of the Router's LAN ports
to your computer's network port.
4. Turn on your Cable/DSL modem.
5. Turn on your router.
6. Turn on your computer.
POWER
LAN
Verify Hardware Installation
Verify that the following router front panel lights are on: Power, WAN, and one
LAN port. (for each computer connected to your router)
English
WAN

4
3. Configure the computer's TCP/IP Settings
Windows 95/98/98SE/ME
This next section will ensure that your computer can communicate with your
router. To do this, you will need to configure the TCP/IP settings in your
Operating System (OS). Configuration instructions for Windows OS-based
computers are shown below. For computers running other operating systems,
see your system documentation for configuration instructions.
1. Find the Start Button located on the Desktop.
2. Click Start;Click Settings and then click on Control Panel.
3. Double-Click the Network Icon and the Network Properties box will appear.
4. Under the General Configuration Tab, locate and select TCP/IP with the
corresponding network card (such as TRENDnet TE100-PCIWN
10/100Mbps Network Adapter). Then, click on the Properties button, and
the TCP/IP window will appear.
NOTE: If you have a Static IP address connection, write down the IP
addresses from the following sections before you change the settings.
English

5
6. Now go to the Gateway tab and make sure no Gateways are listed in the
Installed Gateway's section. If there is Gateway installed, click Remove to
remove it.
5. Under the IP Address Tab, select Obtain an IP address automatically.
English

6
7. Go to the DNS Configuration tab, and click Disable DNS. Then click OK.
8. Click OK on the TCP/IP Properties box.
9. Click OK on the Network Box.
10. At this point, the installation may require files from your Windows CD-ROM.
If this happens, insert your Windows 98 CD-ROM into your CD-ROM drive
and select CD-ROM drive to load the files.
11. After the files load and the “System Settings Change” message appears,
click Yes to reboot your system. Your computer will now load your new
TCP/IP settings.
NOTE: If the message does not appear, you will need to manually
restart your computer.
English

7
13. The IP configuration box will appear. Choose your Network adapter from
the dropdown box (such as TRENDnet TE100-PCIWN 10/100Mbps network
adapter)and the current IP address information of your computer will show
in the box, including the following: IP Address, Subnet Mask and Default
Gateway.
14. If your IP Address shows the following information, your computer is now
successfully connected to the router:
IP Address: 192.168.0.x
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
NOTE: If the information shown is incorrect, please reboot and retry the
steps above.
12. After your system reboots, click Start; click on Run. Then type winipcfg in
the field and then click OK.
English

8
1. Click Start; Drag Mouse to Settings and then click on Control Panel.
2. Double-click the Network Connections Icon.
3. Right-click on the Local Area Connection Icon, and then click on
Properties. The Local Area Connection Properties box will appear.
4. Under the "General Configuration" Tab, locate and select TCP/IP and then
click Properties. The Internet Protocol (TCP/IP) Properties box will appear.
NOTE: If you have a Static IP address connection, write down the IP
addresses from the following sections before you remove them from the
settings.
Windows 2000/XP
5. Click on Obtain an IP address automatically and Obtain DNS Server
address automatically.
English

9
6. Click OK.
7. Click Close on the Local Area Connection Properties box.
8. Click on Start; click on Run. Then type cmd and click OK.
9. The Command Prompt window will appear. Type ipconfig at the C:\ prompt
and press the Enter key.
10. If your IP Address shows the following information your computer is now
successfully connected to the router:
IP Address: 192.168.0.x
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
NOTE: If the information shown is incorrect, please reboot the computer
and retry the steps above.
English

10
The following set-up information is designed to help you to set-up your router to
connect to the Internet. The set-up is different depending upon the type of
Internet Connection you have with your ISP. If you're not sure what type of
connection you have please contact your Internet Service Provider and collect
the required information, which is located in the
section at the beginning of this Quick Installation Guide.
“Prepare for Installation”
Launch your Internet browser (Explorer or Navigator) and type in
http://www.trendnet.com. If the web site comes up in the browser, your router
is configured properly.
4. Configure the Router
Dynamic IP Cable Connection
NOTE: If the website does not appear, please verify your connection
type with your ISP.
English

11
3. Select the Specified IP Address, (Static IP Address) and the information
provided by your ISP, and click Save.
4. Launch your web browser, (Internet Explorer or Netscape Navigator) type
http://www.trendnet.com in the address bar, and hit the Enter key. If the
website appears, your router is configured properly.
NOTE: If the website does not appear, please verify your connection
type with your ISP.
English
1. Launch your Internet browser (Explorer or Netscape), and then type
http://192.168.0.1 in the address bar and hit the Enter key. The
TW100-BRV204's configuration page should appear.
2. Click on the Internet Option on the left-hand side of the screen and select
WAN Port. The WAN Port configuration page will appear.
Static or Fixed IP Cable Connection

12
3. Select PPPOE for the Login Method; the User Name/Password field will
appear. Enter PPPOE User Name and Password, and click Save.
4. Launch your web browser, (Internet Explorer or Netscape Navigator) type
http://www.trendnet.com in the address bar, and hit the Enter key. If the
website appears, your router is configured properly.
NOTE: If the website does not appear, please verify your connection
type with your ISP.
English
PPPoE DSL Connection
1. Launch your Internet browser (Explorer or Netscape), and then type
http://192.168.0.1 in the address bar and hit the Enter key. The
TW100-BRV204's configuration page should appear.
2. Click on the Internet option on the left-hand side of the screen and select
WAN Port. The WAN Port configuration page will appear.

13
3. Select PPTP for the Login Method, and the User Name/Password field will
appear. Enter your User Name/Password under PPTP and then click Save.
4. Launch your web browser, (Internet Explorer or Netscape Navigator) type
http://www.trendnet.com in the address bar, and hit the Enter key. If the
website appears, your router is configured properly.
NOTE: If the website does not appear, please verify your connection
type with your ISP.
English
PPTP DSL Connection
1. Launch your web browser, (Internet Explorer or Netscape Navigator), type
http://192.168.0.1 in the address bar, and hit the Enter key. The Tw100-
BRV204's configuration page should appear.
2. Click on the Internet option on the left-hand side of the screen and select
WAN Port. The WAN Port configuration page will appear.

14
MAC Address Cable Connection
1. Launch your Internet browser (Explorer or Netscape), type
http://192.168.0.1 in the address bar, and hit the Enter key. The
TW100-BRV204's configuration page should appear.
2. Click the Internet option on the left side of the screen, and select WAN Port.
The WAN Port configuration page will appear.
3. At the MAC Address section, click on Copy from PC and click Save.
4. Launch your web browser, (Internet Explorer or Netscape Navigator) type
http://www.trendnet.com in the address bar, and hit the Enter key. If the
website appears, your router is configured properly.
NOTE: If the registered MAC Address your ISP gave you is different
than your PC's MAC Address, please enter the registered MAC Address
for your account, and click Save.
NOTE: If the website does not appear, please verify your connection
type with your ISP.
English

15
1. Préparation de l'installation
Français QIG
Français
Obtenez les informations de votre fournisseur
d'accès Internet (FAI)
Veuillez vérifier votre type de connexion et vous assurer que vous disposez des
informations suivantes :
Connexion IP dynamique par câble
Rien n'est nécessaire. L'adresse IP sera assignée automatiquement par
l'ISP.
Connexion IP statique ou fixe par câble
Adresse IP Internet :____.____.____.____ (p. ex. 215.24.24.129)
Masque de sous-réseau : ____. ____. ____. _____
Adresse IP de la passerelle :____.____.____._____
DNS principal :____.____._____.______
DNS secondaire :____.____._____.______
Connexion DSL PPPoE
Nom d'utilisateur :______________
Mot de passe :________________
Connexion DSL PPTP
Nom d'utilisateur :______________
Mot de passe :________________
Connexion câblée avec adresse MAC:
L'adresse MAC enregistrée de votre FAI pour votre compte
Internet:___.____.____.____ .____.____ (p. ex. 00-0E-FF-04-CC-EE)
(L'adresseMAC est normalement associée au modem câble/DSL ou à la
carte réseau du PC).

16 Français
2. Installation du matériel
32
TW100-BRV204
POWER
1. Mettez votre modem câble/DSL, votre ordinateur et votre routeur hors
tension.
2. Branchez un câble réseau RJ-45 du port Ethernet du modem au port WAN
du routeur.
3. Branchez un autre câble réseau RJ-45 de l'un des ports LAN du routeur au
port réseau de votre ordinateur.
4. Mettez votre modem câble/DSL, votre ordinateur et votre routeur sous
tension.

17 Français
3. Configuration des paramètres TCP/IP
Windows 95/98/98SE/ME
Configurez les paramètres TCP/IP de votre ordinateur pour accéder au routeur.
1. Localisez le bouton Start (Démarrer) situé sur le bureau.
2. Cliquez sur Start (Démarrer), sur Settings (Paramètres) et sur Control
Panel (Panneau de configuration).
3. Double-cliquez sur l'icône Network (Réseau), et la boîte Network Properties
(Propriétés réseau) s'affichera.
4. Sous l'onglet General Configuration (Configuration générale), trouvez et
sélectionnez TCP/IP avec la carte réseau correspondante (comme
TRENDnet TE100-PCIWN 10/100Mbps Network Adapter), cliquez ensuite
sur le bouton Properties (Propriétés). Cliquez ensuite sur Properties
(Propriétés) et la fenêtre TCP/IP s'affichera.
REMARQUE : Si vous disposez d'une connexion avec une adresse IP
fixe, inscrivez les adresses IP des parties suivantes avant de pratiquer
toute modification.

18 Français
6. Rendez-vous à présent sous l'onglet Gateway (Passerelle) et assuez-
vous qu'aucune passerelle n'est reprise dans la partie Intalled Gateways
(Passerelles intallées). S'il y en a une d'installée, sélectionnez-la et cliquez
sur Remove (Supprimer) pour la supprimer.
5. Sous l'onglet IP Address (Adresse IP), cliquez sur Obtain an IP address
automatically (Obtenir une adresse IP automatiquement).