TRENDnet TV-IP315PI User manual

TV-IP315PI
Quick Installation Guide

Table of Content
1 English
1. Before You Start
2. Hardware Installation and Configuration

1
1. Before You Start
Package Contents
ŸTV-IP315PI
ŸCD-ROM (Utility and User's Guide)
ŸQuick Installation Guide
ŸMounting kit
Minimum Requirements
ŸPower over Ethernet (PoE) switch (e.g. TPE-TG80g) or PoE Injector (e.g. TPE-113GI)
ŸA networked computer and web browser
ŸWired network
ŸNetwork cable
Note:
ŸThe TV-IP315PI only works with Power over Ethernet (PoE) devices that follow the IEEE
802.3af standard.
ŸThe TV-IP315PI has a 5.5 mm barrel connector for an optional 12 V DC 1A power adapter.
ŸOptional Power Supply (not included).
TRENDnetVIEW Pro Requirements
Supported Operating
Systems
1-8 Cameras
CPU CPU
9-32 Cameras
Memory Memory
Windows 10/
Windows 8.1/
Windows 8 /
Windows 7/
Windows Server 2008
2 GHz 2 GHz2 GB RAM
or above
4 GB RAM
or above

2. Hardware Installation and Configuration
2
1. Do not install or mount the IP camera until after you complete the installation steps below.
Temporarily place the IP camera next to your computer.
2. Insert the Utility CD-ROM into your CD-ROM drive.
3. Select language from the drop down menu.
4. Click Install Camera.
5. Write down the MAC address of your camera. Then click Next.
Next

3
6. Connect a network cable from the camera's network port to your PoE source The IR LEDs will
turn on and show a dim visible red light. Allow 60 seconds for the camera to boot up. Then click
Next.
7. Select your camera. Click Next and follow the instructions.
Next
Next

4
8. Select DHCP option to assign an IP by DHCP server, select “Fixed IP” to set IP address
manually. Click Next.
9. If you select “Fixed IP”, fill out the IP address, subnet mask, default gateway, and DNS server.
Please ensure that the IP address of the camera and the computer must be within the same
network. Click Next.
10. Select Change Password. Enter a new password, confirm the new password and then click
Next.
Next
Next

5
12. Congratulations! Your camera is now ready to be installed in its final location. Scan the QR
code to download a free mobile app to view the camera from your mobile device. Click Finish
to exit the installation wizard.
11. Initial Setup is complete! Your camera is now connected to your network. Click the hyperlink
to confirm access to the management page. This will open up a web browser. To resume
installation, minimize the web browser and then click Next.
Finish
Next

6
13. To manage multiple cameras and for more advanced features, please install the
TRENDnetVIEW Pro software. Install the software by clicking Install TRENDnetVIEW Pro
Software in the Autorun window and refer to the TRENDnetVIEW Pro User's Guide on the CD
for more information.
Note
ŸSee User's Guide for advanced management functions
ŸTwo User's Guides are included – one for the camera and one for the complimentary
management software.

7
Using the TV-IP315PI with a PoE switch (TPE-TG80g)
ŸBefore mounting the camera, the lens must be manually positioned and focused.
ŸConnect a network cable from the Power over Ethernet switch (e.g. TPE-TG80g) to the
network port on the IP Camera.
ŸConnect the switch to your network.
TPE-TG80g
PoE
Internet
TV-IP-315PI
14. Install the camera in your desired location. To connect the IP camera to your network with
PoE, please use either of the following examples:
Non-PoE

8
TPE-113GI
DATA
IN
PWR+DATA
OUT
Non-PoE
PoE
ŸConnect the power adapter to the TPE-113GI and then to a power outlet.
ŸConnect a network cable from the TV-IP315PI to the TPE-113GI's PWR+DATA OUT (PoE)
port.
ŸConnect a network cable from a switch or router (e.g. TEW-818DRU) to the TPE-113GI's
DATA IN (Non-PoE) port.
Using the TV-IP315PI with an Injector (TPE-113GI)
TV-IP-315PI
Internet