TRENDnet TV-IP252P - SecurView PoE Dome Internet Camera... User manual

TV-IP252P
1.01
Quick Installation Guide

Table of Contents
Version 07.18.2009
English 1
1. Before You Start
2. Hardware Installation 2
3. Configure the IP Camera 3
1
4. Power over Ethernet (PoE) Installation 7
Troubleshooting 9

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
1. Before You Start
Package Contents
?
?Multi-Language Quick Installation Guide
?Utility CD-ROM
?RJ-45 cable
?Mounting Kit
?AC Power Adapter (12V, 1.5A)
TV-IP252P
Note:
1. The TV-IP252P only works with Power over Ethernet (PoE) devices that follow
the IEEE 802.3af standard.
2. Before mounting the TV-IP252P, the lens must be manually positioned
and focused.
System Requirements
?10/100Mbps Ethernet Adapter
?CPU: 350MHz or above / 800MHz (Windows Vista)
?Memory: 256MB RAM or above / 512MB RAM or above (Windows Vista)
?Windows 2000/XP/Vista
?VGA Resolution: 800 x 600 or above
?Web Browser: Internet Explorer (6.0 or higher)
?Router
?An available DHCP Server (routers usually have a built-in DHCP server)
?Power over Ethernet (PoE) Switch (e.g. TPE-80WS) (Optional)
?Injector (e.g TPE-111GI ) (Optional)
1

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
2. Hardware Installation
2
1. Connect the provided RJ-45 network cable
from a Switch/Router to the Ethernet port on
the IP Camera.
2. Connect the AC Power Adapter to the IP
Camera and then to a power outlet.

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
2. Follow the IPSetup Setup Wizard
instructions and then click Next.
3
1. Insert the Utility CD-ROM into your CD-ROM
drive and then click IP Setup.
3. Click Close.
4. Go to Start -> Programs -> TRENDnet ->
IPSetup and click IPSetup.
3. Configure the IP Camera
Note:
1. It is recommended that you configure the IP Camera from a wired computer.
2. If you would like to use SecurView software, please refer to the User's Guide on
the CD for more information.

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
6. Configure the IP address to be in the same
subnet as your network, type in the
Administrator ID and Password and click
Change. By default:
ID: admin
Password: admin
4
Note:
By default, the IP setting on the TV-IP252P is set to DHCP. Please skip to step 9. If
you want to give the TV-IP252P a static IP address, continue on to step 5.
5. Select the IP camera and click Change IP.
7. Click OK and wait 30 seconds.
8. Click OK.

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
11. Right click on the Internet Explorer Information
Bar and select Install ActiveX Control.
5
9. Double click the IP camera to access
the browser configuration.
10. Enter the User name and Password, and
then click OK. By default:
User Name: admin
Password: admin
12. Click Install.

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
6
13. Click Live View.
Your Installation is complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
For detailed information regarding the TV-IP252P configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
TRENDnet's website at http://www.trendnet.com.

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
7
4. Power over Ethernet (PoE) Installation
1. Connect a RJ-45 cable from the Power Over
Ethernet switch (e.g. TPE-80WS) to the LAN
port on the IP Camera.
2. Verify that the LEDs are on. Please refer to
step 4 in the Hardware Installation section.
Using the TV-IP252P with a PoE switch

ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
8
1. Connect the Power Cord to the Injector.
Then connect the Power Cord to an outlet.
2. Connect a CAT-5e/6 cable from a switch to
the TPE-111GI's DATA IN port.
3. Connect a CAT-5e/6 cable from the
TV-IP252P to the TPE-111GI's DATA OUT port.
4. Verify that the LEDs are on.
Using the TV-IP252P with an Injector (TPE-111GI)