TRENDnet TEG-2248WS - Gigabit Web Smart Switch User manual

Quick Installation Guide
TEG-2248WS
H/W: B1

Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
3
2
6
1. Before You Start
2. Hardware Installation ........................................................................
3. Web Smart Switch Management Utility ..............................................
................................................................................
Table of Contents
Version 07.25.2008

System Requirements
Application
?TEG-2248WS
?Quick Installation Guide
?Utility & User Guide CD-ROM
?2 Mounting Brackets with Screws
?Power Cord
?Web Browser: Internet Explorer (5.0 or above), Netscape (6.0 or above)
?Computer with Network adapter installed
?Optional Mini-GBIC modules (e.g. TEG-MGBSX, TEG-MGBS10,
TEG-MGBS40, TEG-MGBS80, TEG-MGBS10D3_5, TEG-MGBS40D3_5)
for Mini-GBIC slots
Package Contents
1. Before You Start
English
1
1000Mbps
Mini-GBIC Module
(TEG-MGBSX)
Workstations with
Fast Ethernet PCI Adapter
(TE100-PCIWN)
10/100Mbps
52-Port 10/100/1000Mbps Gigabit Web Smart Switch
(TEG-2248WS)
Cable/DSL 4-Port
Broadband Router
(TW100-S4W1CA)
Internet
Workstations with
Copper Gigabit PCI Adapter
(TEG-PCITXR)
VLAN Group 2VLAN Group 1
Cable/DSL
Modem
10/100Mbps

2. Hardware Installation
English
2
2. Connect a CAT-5, CAT-5e or CAT-6
RJ-45 network cable from the
computer to an available Ethernet
port of the TEG-2248WS.
1. Connect the Power Cord to the
rear of the TEG-2248WS and then
to a power outlet.
Note:
1. After hardware installation is complete, use the Web Browser to configure
the TEG-2248WS. Open your web browser, and enter the default IP
Address http://192.168.0.1 and default password "admin". Make sure your
computer and the TEG-2248WS are configured to the same network
segment.
2. The Mini-GBIC slots are shared with Port 49 and 50 Gigabit Ethernet ports.
When the Mini-GBIC slots are in use, port 49 and 50 Gigabit Ethernet ports
are disabled.

English
3
Note: If you would like to easily discover all the Web Smart Switches on the
network, assign IP Address, change the password, and upgrade to new
firmware, then install the Web Smart Switch Management Utility. Follow the
steps below.
3. Click Start > Programs >
TRENDnet > Web Smart Switch
Management Utility, and then
click Web Smart Switch
Management Utility.
3. Web Smart Switch Management Utility
For Windows User
1. Insert the Utility & User’s Guide
CD-ROM into your computer's
CD-ROM Drive and then click
Install Utility.
2. Follow the Installation Wizard
instructions. Click OK.

English
4
4. Click Discovery, and then double-
click the Switch that appears in
the Discovery List.
5. Click the Switch in the Monitor
List and then click Configuration
setting.
6. Configure the IP Address, Subnet
mask, Gateway, and Password.
Click Set.

English
5
7. Click OK.
8. Click Access Web.
9. Type in your Password and then
click Login. By default, the
Password is admin.
For more information regarding the Web Smart Switch Management Utility
configuration and advanced settings, please refer to the User's Guide included
on the Utility CD-ROM or TRENDnet's website at www.trendnet.com
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet

Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
Q5:
A5:
After connecting the TEG-2248WS to a power outlet, the LEDs do not turn on.
Check the connection of the power cord to the TEG-2248WS and the power
outlet. Also check that the power outlet is receiving power.
After installing the Web Smart Switch Management Utility, I clicked Discovery and the
Utility is unable to discover the TEG-2248WS. What should I do?
Make sure that the TEG-2248WS is powered on and that all connections are secure.
Also check that your computer's IP Address is on the same network segment as the
TEG-2248WS. The default IP Address of the Switch is 192.168.0.1 and the default password
is admin.
When I access the TEG-2248WS using a web browser, I get a screen that tells me “only
one user can login”. What should I do?
Another computer is configuring the TEG-2248WS. Please wait until the user logs off. If
the other user has already logged off and you still get the same screen, then disconnect the
power cord from the TEG-2248WS, wait for 5 seconds, reconnect the power cord to the
TEG-2248WS, allow 5 seconds for the Switch to power on, and then attempt to access the
web configuration page to login.
I forgot the administration password. How do I reset my TEG-2248WS?
Press on the reset button using a pen or paperclip for 10 seconds. The default
password is admin.
When I connect a computer to the Switch’s Gigabit port, I am not getting Gigabit
speeds. What should I do?
Check the LED on the Switch. When the LED is amber, the computer’s connection
speed is 10 or 100Mbps. Make sure that you have a Gigabit Ethernet adapter installed. Also
make sure to use a Cat-5e or Cat 6 Ethernet cable. Some Cat-5 cables are not rated to run
in Gigabit.
If you still encounter problems or have any questions regarding the TEG-2248WS, please refer to
the User's Guide included on the Utility CD-ROM or contact TRENDnet’s Technical Support
Department.
6
Troubleshooting

Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón
necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir
daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y
frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalación.

Copyright ©2008. All Rights Reserved. TRENDnet.
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
20675 Manhattan Place
Torrance, CA 90501
USA