TriMark e-ASK User manual

e-ASK
electronic Access Security Keyless-entry
Discrete e
Discrete e- -PAD PAD
Instruction Manual
(UM10 ~ 21067-01)

Table of Contents
Introduction ............................................................................... 1
e-PAD Operation and Features................................................ 1
Locking Doors With Keypad................................................... 2
Secure Operations.................................................................. 2
Dome Light Activation............................................................. 2
Protective Deactivating Security Feature ............................... 2
Buzzer Operation.................................................................... 3
Keypad Backlight Operation ................................................... 3
Teaching Keypad New Authority / Access Codes ................. 3
Changing Authority Code....................................................... 3
Change / Add Access Codes ................................................. 4
Appendix A: Mounting Information.......................................... I
Appendix B: Wiring Information.............................................. II
Wire Identification................................................................... II
Wiring Diagram.......................................................................III

Introduction
This manual provides the necessary information for the proper
installation and use of TriMark’s discrete e-PAD system.
Note: Some features discussed in this manual may not be available
on your system.
e-PAD keypad
1
Note: Horizontal or vertical e-PADs are available.
e-FOB Operation and Features
The e-PAD is shipped with default authority and access codes. Unless
the OEM or dealer has changed the default codes, the authority and
access codes are as follows:
Access code:
Authority code:
Digit 1 Digit 2 Digit 3 Digit 4 Digit 5
1 / 2 3 / 4 5 / 6 7 / 8 9 / 0
Digit 1 Digit 2 Digit 3 Digit 4 Digit 5
7 / 8 7 / 8 7 / 8 7 / 8 7 / 8

Notes:
• The authority code does not allow for secure operations. It is
only used to assign access codes (see page 3 for information
on setting authority and access codes).
• If an unassigned button or no button is pressed while the
system is enabled, the keypad reverts back to disabled state.
• The secure keypad operations are set depending on the system
configuration.
Dome Light Activation
The dome light is activated for 30 seconds whenever a secured
operation occurs.
Protective Deactivating Security Feature
After repeated entering of incorrect codes (20 button presses without
enabling), the keypad is deactivated for 1 minute. This helps prevent
unauthorized access by entering random codes.
No beep will sound with button press while the system is disabled.
2
Locking Doors With Keypad
Press and hold down the (1 / 2) button for 1-2 seconds. An access
code is not needed to lock the doors.
Secure Operations
Entering a valid 5-digit access code enables secure operations. After
entering an access code, the keypad is enabled for 5 seconds and a
6th button press initiates a secure operation, such as unlocking the
doors.
The table below shows the default button assignments:
1 / 2 Button Unlocks entry doors
3 / 4 Button
5 / 6 Button Unlocks Bank Two (may be set to left side of vehicle)
7 / 8 Button Unlocks entry doors, Bank One and Bank Two with
staggered actuation
9 / 0 Button Activates light for 5 minutes. Repeating sequence while
light is on turns light off.
Unlocks Bank One (may be set to right side of vehicle)

3
Buzzer Operation
The buzzer chirps once when power is first applied to the keypad and
for each key press during regular use. When an authorized access
code is entered, the system chirps twice to indicate readiness for a
secure operation (6th button press).
The system chirps twice for each button press while in Learn Mode.
When a new access code is defined, the system chirps 3 times.
Keypad Backlight Operation
When the e-PAD is in the normal state, the backlighting is at a low
level. When a button is pressed, the keypad backlight flashes bright.
The keypad backlight also has a power saving mode if voltage is
below 11 volts, the continuous backlighting is shutoff until the battery
is fully charged. When continuous backlighting is off, the keypad still
“wakes up” when a button is pressed. In this case, the backlighting is
activated for only one minute.
If the battery voltage is increased to 12.5V for 5 minutes, then the
keypad back lighting will return to low brightness level.
Teaching Keypad New Authority / Access
Codes
Change Authority Code
The following procedure resets the default authority and access codes.
It then assigns a new authority code. The authority code is only used to
teach access codes.
Notes:
• The memory for authority and access codes is NON-VOLATILE
and will not be erased if power is removed.
• Changing the authority code is the only activity that requires
access to the learn mode wire in the wiring harness.

4
Change/Add Access Codes
With a valid authority code, an access code can be programmed with
the following instructions.
1. Press the (5 / 6) button for 5 seconds, the keypad will beep.
The backlighting LED of the keypad will flash indicating the
learn mode.
2. Enter in the 5-digit authority code. Keypad will provide a long
beep that will stop after you have defined an access number.
Digit 1 Digit 2 Digit 3 Digit 4 Digit 5
Authority Code
The procedure is:
1. Ground the yellow learn mode wire. The buzzer will chirp for
approximately 3 seconds and the keypad backlights will flash to
indicate learn mode (back lights can only be seen when dark).
2. Enter the new 5-digit code. (Double chirps after each button
press). The keypad will chirp 3 times after the 5-digit entry.
3. Enter the new code again for confirmation. (Again double chirps
after each button press). Then keypad will chirp four times after the
5-digit code is confirmed. A long beep indicates that codes did not
match (if this occurs then previous codes remain, keypad exits
from learn mode, and above steps need to be repeated to change
codes).
4. The keypad will automatically exit learn mode after successive
completion of steps 1-3 above. Next confirm that the above code
works as an access code. Now each button press will only provide
1 chirp, and then a double chirp indicates that the keypad is
enabled (and ready for secured operation depending on 6th button
press).
The user is given 2 minutes to complete this procedure. If it isn't
completed in time, or an error is made, the system will exit learn mode
and a long chirp will sound to indicate the error.
The following area can be used to document the authority code:

5
3. Press and release the button that corresponds to the access
number. For example, press the (1 / 2) button for access #1
and press the (3 / 4) button for access #2. The keypad will
provide a confirmation beep after this single button press.
4. Enter the new 5 digit access code after this single button press.
5. Re-enter the new 5 digit access code. The keypad will provide
confirmation beeps.
Repeat process to assign additional access codes.
Note: Up to 5 different access codes can be assigned at one time. As
additional access codes are defined, pre-existing access codes are
overwritten. For example, if a new access code is assigned for access
#3, the previous access #3 code is no longer valid.
The following area can be used to document the access code
assignments.
Access
# User Name Digit 1 Digit 2 Digit 3 Digit 4 Digit 5
1
2
3
4
5
This product has been manufactured with methods to ensure high
quality and to meet the high expectations of our customers. TriMark
warrants this product to be free from workmanship defects and will
remedy issues per TriMark's warranty policy.
Remote transmitter FOBs, batteries, and other equipment subject to
normal wear and deterioration may need to be replaced periodically by
dealer and/or end user and are not covered by this warranty. TriMark
will not be liable for indirect, special, incidental or consequential
damages.
Contact TriMark for specific mounting details, such as drawings,
placement suggestions, mounting hardware, etc.

Appendix A: Mounting Information
I

Appendix B: Wiring Information
Wire Identification:
1. Red / White Wire – Relay 12V
2. White / Green Wire - lock all
3. White / Red Wire – unlock all with 1/2 secure
operation (entry doors)
4. Brown Wire—unlock with 3/4 secure
operation (bank 1)
5. Orange Wire—unlock with 5/6 secure
operation (bank 2)
6. Pink Wire – Output actuated with 9/0 secure
operation (lights)
7. Red Wire - system power, 12-14V
8. Black Wire - system ground
9. Yellow Wire - ground for entering learn mode
.
1 2 3
4 5 6
7 8 9
TERMINAL
IDENTIFICATION
II

Wiring Diagram
BROWN
#4
UNLOCK
Bank 1
ORANGE
# 5
UNLOCK
Bank 2
RED/WHITE
#1
RELAY POWER
RED #7
+ 12 VDC
POWER
SOURCE
BLACK
#8
GROUND
WHITE/GREEN
#2
LOCK
OUTPUT
WHITE/RED
#3
UNLOCK
Entry
12 VDC
BATTERY
85
86
87a 87
30
85
86
87a 87
30
85
86
87a 87
30
85
86
87a 87
30
GREEN #9
LEARN MODE -
SHORT TO GND
ENTRY
BANK 1
BANK 2
PINK
# 6
LIGHTS
85
86
87a 87
30
LOCK
ALL
UNLOCK
ENTRY
UNLOCK
BANK 1
UNLOCK
BANK 2
LIGHTS
III

Notes

UM10
21067-01
03/06-2