Triotech TYPHOON User manual

Preliminary – January 2009
USER MANUAL
TYPHOON
Triotech Amusement Inc.
190 Des Industries Lavaltrie, Quebec (Canada)
J5T 3R2
Tel.: [phone]
Toll free: 1-888-IN-LINE-4
Fax: [phone]
e-mail: [email protected]

Dear valued customer,
Congratulations and thank you for purchasing TRIOTECH
AMUSEMENT’s Typhoon. You will not be disappointed with your
purchase. Your 2-seat theater is coin-operated and does not require
attendant. Featuring 4.1 Surround Sound and a 42” LCD screen this
dual-actuator motion platform is the most realistic simulation avail-
able in coin-op.
Sincerely,
TRIOTECH

CAUTION
Typhoon requires a dedicated 120V. 15 amp circuit or 220V. 7.5amp or the
machine may experience sporadic technical difficulties. Your Typhoon should
not share a breaker with other deluxe or motion based cabinets.
!
Determine Optimum Location
The game location must be free of: exposure to direct sunlight, high humidity, dust, salt mist,
high heat, or extreme cold. If installed in an unusually hot location, allow additional clearance
between ventilation slots in the game and any structure or object that would tend to restrict air
circulation.
TYPHOON Ships in one (1)
crate
Typhoon reception
Reception
1
Package approximate dimensions:
90” x 56” x 80”

LIST OF SUPPLIED ASSEMBLY PARTS
Reception
2
Item Description Photo/ Image Qty.
1Main cabinet
1
2Motion seat module
1
3Header assy
1
4Fan’s cover (right
&left)
2
5Hardware box
(inside of the coin
door; the access is
from the front of the
machine; a bag with
the necessaries keys is
attached to the coin
door's door)
1
Package Content

HARDWARE BOX MANIFEST
Reception
3
Bag
or
bin
No. IMAGE DESCRIPTION SIZE QTY. SPARE
1SD-100-0215 FLAT WASHER NEORENE #10 26
2SD-100-0187 PAN HEAD QUADREX
DRIVE #10-24 x 3/4" 26
3SD-100-0216 FLAT WASHER NEOPRENE #14 12
4
SD-100-0190
PAN HEAD QUADREX
DRIVE 1/4-20 x 3/4" 12
5SD-100-0328 LOCK WASHER 1/2" 6
6SD-100-0047 FLAT WASHER 1/2 “ 6
7
SD-100-0342
HEX.MACHINE SCREW 1/2 “-13 x 4” 6

NECESSARY TOOLS
TO COMPLETE ASSEMBLY
Installation
4
No. Tools Description /Image Application
1Forklift Capacity over 1000 lb
Appropriated long forks attached (~65”) Put the carrying package in the place
2Socket 3/4"
Install the seat module (pg.14)
3Wrench 3/4”
Adjust the height of the cabinet
and seats (pg.9 and 14)
4Screwdriver
no.2 (square)
(Screw #10)
Or
Phillips #2
Install the fan’s covers on to the
header(pg.10 )and the header to
the cabinet (pg. 11)
5Screwdriver
no.3 (square)
(Screw 1/4)
Or
Phillips #3
Install the header on the cabinet
(pg.11)

SPACE REQUIREMENTS
Installation
5
For installation, the required space is ~ 15’ X 10’
When fully assembled, the required space will be ~ 7.5’ X 8’

Uncrating
Installation
6
1 - Start by removing the header assem-
bly from the seat.
2- Remove the header support
3- Remove the back legs holder
4-Pull the seat out of the cabinet about 6’’
or 15cm. Then pull the 3 cables out of the
hole one by one as shown in the picture
below.
5- Remove seat assembly from the crate.
6- Remove cabinet from the crate and
move in the desired final location.
- Locate the hardware box inside of the
coin door
- You will find a description of the hard-
ware on the bag.

STEP 2. Header assembly
Install the two fan covers (right and left) to the cabinet
Header
Installation
7
Tools Fasteners Reference
Screwdriver no.2 Flat neoprene washer #10”(14X),
Screw #10-32 x 3/4”(14X)

Header
Installation
7
STEP 3. Header installation
Tools Fasteners Reference
Screwdriver no.2
(Down side, upside ) Flat neoprene washer #10”(12X), Screw #10 -32 x 3/4”(12X)
Screwdriver no.2
(right and left side fan’s cover) BAG/BIN NO: Flat neoprene washer #14”(12X), BAG/BIN NO : Screw 1/4"-20x
3/4”(12X)
Place the header on the machine as shown

Header
Installation
7
Once connected, close & lock top door.
- Open the back service door.
- Connect the header cables. There are three connectors; one MOLEX, 9 pin and one 15 pins +
one NEMA /standard 110V.

Seat
Installation
8
Align seats for wires to easily run through hole on lower right part of
cabinet.

Fasten seats to cabinet using 6 hexagonal head screw 1/2" -13 x 4”, flat
and lock washer. Level seats using adjustable feet
Seat
Installation
8
Tools Fasteners Reference
Ratchet 3/4" Flat washer 1/2”( 6X), lock
washer 1/2 (6X), Hex. Screw
1/2”-13 x 4”( 6X)
Wrench 3/4" Levelling feet

Seat
Installation
8
Through lower right (back of cabinet) door, connect wires you ran.
(Three connectors: NEMA /standard 110V to electric box, RJ45 to
Opto board (only one with RJ45 connection) and the Molex 9 pin con-
nector to its female connector
Once plugged in, lock door.
Opto-card
Main electric box
Molex 9-pin

Installation
Installation
9
Before you connect, make sure main switch is in off position.
Connect power cord to cabinet and wall outlet.
Then turn the main switch ON

Accessing operator settings interface is done by opening the
coin mech door and pushing the micro switch attached to the
coin mech (while in attract mode only).
Operator Setting
Configuration
10

To access the statistic mode screen, press the micro switch once (or toggle micro
switch until you reach this screen).
Operator Setting
Configuration
10
1. Amount of credits inserted into game in lifetime.
2. Amount of money inserted into game in lifetime.
3. Value of one credit
4. Actuator usage time since game installed
5. Actuator usage time since game installed
6. Revenue from each movie installed

Operator Setting
Configuration
10
Use the large dash selection buttons 1 through 6 to change configurations. To
change any of the options, press the appropriate button until the desired setting is
reached. To return to a previous setting, keep toggling the button until it reaches
the end of the settings; then it will restart the settings from the beginning.
Amount of credits needed to start game. Set to 0 for free play (Press 1)
Choose to display credits or money on screen. (Press 2)
Value of one credit. (Press 3)
Sound volume in attract mode. (Press 4)
Hit the appropriate button on the header to change variables