Tripp Lite B130-101A-WP User manual

1
Owner’s Manual
VGA with Audio Over Cat5
Extender Wallplate Kit
Model: B130-101A-WP
Español 7
Installation 5
Product Features 2-3
Specifications 3
Safety Information 2
Français 13
Warranty & Warranty Registration 6
Optional Accessories 3
Features 4
Package Contents 2
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Note: Follow these instructions to ensure proper operation and prevent damage
to this device and its connected equipment.
Copyright © 2009 Tripp Lite. All rights reserved.
All trademarks are the property of their respective owners.
Warranty
Registration:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
200908079 93-2929.indb 1 9/22/2009 12:25:46 PM

2
• To reduce the risk of electric shock, do not expose the product to moisture.
• Operate this product using only the included external power supply. Use
of other power supplies could impair performance, damage the product, or
cause fire.
• Use only recommended accessories to avoid fire, shock or other hazards.
• Unplug this product before cleaning. Use a damp cloth for cleaning. Do
not use cleaning fluids or aerosols, which could enter the unit and cause
damage, fire or electrical shock.
• Do not attempt to service this unit. Instead, disconnect it and visit
www.tripplite.com/support.
• Use of this equipment in life support applications where failure of this
equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness
is not recommended. Do not use this equipment in the presence of a
flammable anesthetic mixture with air, oxygen or nitrous oxide.
• Extends a VGA* and audio signal up to 500 ft. (150 m) using standard
Cat5/5e/6 cable (or up to 1000 ft. at 1024x768 using Zero-Skew UTP
cable)
* Supports VGA, SVGA, XGA, UXGA and WUXGA monitors.
• Local Unit
• Remote Unit
• VGA with Audio Splitter Cable
• (2) 5V, 2.0A DC Power Supplies
• (2) Wallplate Screw Sets
• 110 Punchdown Tool
• Screwdriver
• Owner’s Manual
Safety Information
Product Features
Package Contents
200908079 93-2929.indb 2 9/22/2009 12:25:46 PM

3
• P504-Series Monitor Cables with RGB Coax and Audio, HD15 Male/
Male, Mini-Stereo 3.5 mm Male/Male
• P312-Series 3.5 mm Mini-Stereo Cable
• P502-Series Monitor Cables with RGB Coax, HD15 Male/Male
• P524-Series Zero-Skew UTP Bulk Cable
• N020-01K-GY Cat5e Bulk Stranded Cable, 1000 ft.
• N022-01K-GY Cat5e Bulk Solid Cable, 1000 ft.
• N222-01K-GY Cat6 Bulk Solid Cable, 1000 ft.
Signal Type VGA, SVGA, XGA, UXGA and WUXGA
Video Amplifier Bandwidth 350 Mbps
Input DDC Signal 0.7 Volts p-p (TTL)
Signal Noise Ration 90 dB
Local Unit Ports (1) HD15 Female, (1) 3.5 mm Female,
(1) 110 Punchdown Female
Remote Unit Ports (1) HD15 Female, (1) 3.5 mm Female,
(1) 110 Punchdown Female
Power Supply (2) 5V, 2.0A DC Power Supplies
Dimensions (Local Unit) 2.75 in. (W) x 4.5 in. (H) x 1.1 in. (D)
Dimensions (Remote Unit) 2.75 in. (W) x 4.5 in. (H) x 1.1 in. (D)
Local Unit Weight 0.2 lb
Remote Unit Weight 0.2 lb
Note: Specifications are subject to change without notice. Mass and dimensions are
approximate; please take the actual products as the standard.
Product Features
Optional Accessories
Specifications
• Provides connections for optional local monitor and speakers
• Features built-in Equalization and Gain controls to adjust the video image
• Supports video resolutions up to 1920x1440
• No drivers required
200908079 93-2929.indb 3 9/22/2009 12:25:46 PM

4
1Source Video-In Port: HD15 Female Connector.
2Local Unit Power LED: This LED illuminates when the external power
supply is connected and the unit is receiving power.
3Source Audio-In Port: 3.5 mm Female Connector.
4Power Jack: The 5V, 2A external power supply plugs in here.
5110 Punchdown Connector: Connect Cat5/5e/6 cable between the 110
Punchdown Connectors on the local and remote units.
6Remote Unit Video-Out Port: HD15 Female Connector.
7Remote Unit Power LED: This LED illuminates when the external
power supply is connected and the unit is receiving power.
8Remote Unit Audio-Out Port: 3.5 mm Female Connector.
9Gain Adjustment: Adjusts brightness.
10 EQ Adjustment: Adjusts equalization length.
Features
Local Unit (By Source) Remote Unit (By Display)
Rear
Power
Local
Audio
DC5V, 2.0A
Power
Gain
EQ
Remote
Audio
DC5V, 2.0A
10
1 6
9
3 8
4
4
2 7
5
200908079 93-2929.indb 4 9/22/2009 12:25:48 PM

5
1 Connect the Male end of the VGA with audio splitter cable to the HD15
and 3.5 mm ports on the source computer.
2Connect one of the Female ends of the VGA with audio splitter cable to the
Local Unit’s HD15 and 3.5 mm ports using a VGA cable and audio cable.
3 (Optional) Connect a local monitor and speakers to the remaining
Female connectors of the VGA with audio splitter cable using a VGA
cable and audio cable.
4 Connect the external power supply to the power jack on the local unit
and plug it into an appropriate power source.
5 Connect the 110 Punchdown Connector on the local unit to the 110
Punchdown Connector on the remote unit using Cat5/5e/6 cable.
6 Connect the HD15 and 3.5 mm ports on the remote unit to a monitor
and speakers using a VGA cable and audio cable.
7 Connect the external power supply to the power jack on the remote unit
and plug it into an appropriate power source.
8 Turn the display(s) on first.
9 Turn on the computer.
10 If the video on your monitor is either too dark or too light, use the Gain
Adjustment on the remote unit.
11 If the video on your monitor is fuzzy, or shows a ghosting effect, use the
EQ Adjustment on the remote unit.
Installation
1
2
3
4
56
7
200908079 93-2929.indb 5 9/22/2009 12:25:48 PM

6
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for
a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this
warranty is limited to repairing or replacing (at its sole option) any such defective products. To
obtain service under this warranty, you must obtain a Returned Material Authorization (RMA)
number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned
to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid
and must be accompanied by a brief description of the problem encountered and proof of date and
place of purchase. This warranty does not apply to equipment which has been damaged by accident,
negligence or misapplication or has been altered or modied in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties;
therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE. Specically, TRIPP LITE is not liable for any costs, such as lost prots or revenue, loss
of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims
by third parties, or otherwise.
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.
You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
WEEE Compliance Information for Tripp Lite Customers and Recyclers
(European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing
regulations, when customers buy new electrical and electronic equipment from Tripp Lite they
are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on
the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Tripp Lite follows a policy of continuous improvement. Product specications are subject to
change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Warranty & Warranty Registration
200908079 932929-EN
200908079 93-2929.indb 6 9/22/2009 12:25:48 PM

7
Manual del propietario
Kit extensor de placas de pared
VGA con audio sobre Cat5
Modelo: B130-101A-WP
English 1
Instalación 11
Características del Producto 8-9
Especificaciones 9
Instrucciones de seguridad 8
Français 13
Garantía 12
Accesorios Opcionales 9
Características 10
Contenidos del paquete 8
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Nota: Siga estas instrucciones para garantizar un funcionamiento adecuado e impedir
que se dañe este dispositivo y su equipo conectado.
Copyright © 2009 Tripp Lite. Todos los derechos reservados.
Todas las marcas comerciales son de propiedad de sus respectivos dueños.
200908079 93-2929.indb 7 9/22/2009 12:25:49 PM

8
• Para reducir el riesgo de descarga eléctrica, no exponga este producto a la
humedad.
• Opere este producto utilizando solo la fuente de alimentación externa
incluida. Si emplea otras fuentes de alimentación podría perjudicar el
rendimiento, dañar el producto o provocar un incendio.
• Use solo los accesorios recomendados para evitar incendios,
electrocuciones u otros peligros.
• Desenchufe este producto antes de limpiarlo. Use un paño húmedo para
limpiarlo. No emplee líquidos de limpieza o aerosoles, ya que podría
entrar a la unidad y provocar daños, un incendio o una descarga eléctrica.
• No intente repara esta unidad. En lugar de ello, desconéctelo y visite
www.tripplite.com/support.
• El uso de este equipo en aplicaciones de soporte de vida en donde la falla
de este equipo pueda razonablemente hacer suponer que causará fallas en
el equipo de soporte de vida o afecte significativamente su seguridad o
efectividad, no está recomendado. No use este equipo en la presencia de
una mezcla anestésica inflamable con aire, oxigeno u óxido nitroso.
• Extiende una señal VGA* y de audio hasta 500 pies (150 m) con un
cable Cat5/5e/6 estándar (o hasta 1000 pies/300 m con una resolución de
1024x768 usando un cable UTP Zero-Skew)
* Soporta monitores VGA, SVGA, XGA, UXGA y WUXGA.
• Unidad local
• Unidad remota
• Cable divisor VGA con audio
• (2) fuentes de alimentación CD 5V, 2,0A
• (2) grupos de tornillos para placas de pared
• Herramienta Punchdown 110
• Destornillador
• Manual del propietario
Instrucciones de seguridad
Características del Producto
Contenidos del paquete
200908079 93-2929.indb 8 9/22/2009 12:25:49 PM

9
• Cables serie P504 para monitor con coaxial RGB y audio, HD15 Macho/
Macho, mini estéreo de 3,5 mm Macho/Macho
• Cable mini estéreo serie P312 de 3,5 mm
• Cables serie P502 para monitor con coaxial RGB, HD15 macho/macho
• Cable UTP Zero-Skew a granel serie P524
• Cable trenzado a granel Cat5e N020-01K-GY, 1000 pies (300 m)
• Cable macizo a granel Cat5e N022-01K-GY, 1000 pies (300 m)
• Cable macizo a granel Cat6 N222-01K-GY, 1000 pies (300 m)
Tipo de señal VGA, SVGA, XGA, UXGA y WUXGA
Ancho de banda del
amplificador de video 350 Mbps
Señal DDC de entrada 0.7 voltios p-p (TTL)
Razón de ruido de la señal 90 dB
Puertos de la unidad local (1) hembra HD15, (1) hembra de 3.5mm,
(1) hembra Punchdown 110
Puertos de la unidad remota (1) hembra HD15, (1) hembra de 3.5mm,
(1) hembra Punchdown 110
Fuente de alimentación (2) Alimentaciones de 5V y 2.0A CD
Dimensiones (unidad local) 2.75 x 4.5 x 1.1 (pulg)
Dimensiones (unidad remota) 2.75 x 4.5 x 1.1 (pulg)
Peso de la unidad local 0.2 lb
Peso de la unidad remota 0.2 lb
Nota: Especificaciones sujetas a cambio sin previo aviso. El volumen y las dimensiones
son aproximados; asuma los productos reales como el estándar.
Características del Producto
Accesorios Opcionales
Especificaciones
• Proporciona conexiones para monitor local y altavoces opcionales
• Cuenta con controles de ecualización y ganancia incorporados para ajustar
la imagen de video
• Soporta resoluciones de video de hasta 1920x1440
• No necesita controladores
200908079 93-2929.indb 9 9/22/2009 12:25:49 PM

10
1Puerto de entrada de la fuente de video: conector HD15 hembra.
2LED de energía de la unidad local: Este LED se ilumina cuando
la fuente de alimentación externa está conectada y la unidad recibe
electricidad.
3Puerto de entrada de la fuente de audio: conector de 3,5 mm hembra.
4Tomacorriente: Aquí se conecta la fuente de alimentación externa de
5V, 2A.
5Conector Punchdown 110: Conecte un cable Cat5/5e/6 entre los
conectores Punchdown 110 de la unidad local y de la unidad remota.
6Puerto de salida de video de la unidad remota: conector HD15
hembra.
7LED de energía de la unidad remota: Este LED se ilumina cuando
la fuente de alimentación externa está conectada y la unidad recibe
electricidad.
8Puerto de salida de audio de la unidad remota: conector de 3,5 mm
hembra.
9Ajuste de ganancia: ajusta el brillo.
10 Ajuste de la ecualización: ajusta la longitud de la ecualización.
Características
Unidad local (por fuente) Unidad remota (por pantalla)
Posterior
Power
Local
Audio
DC5V, 2.0A
Power
Gain
EQ
Remote
Audio
DC5V, 2.0A
10
1 6
9
3 8
4
4
2 7
5
200908079 93-2929.indb 10 9/22/2009 12:25:49 PM