Triumph Protect+ User manual

Protect+ User Guide
1 of 9
Publication part number 9901719 issue 3
© Triumph Designs Ltd. 2021 English
The Triumph Protect+ is an alarm system designed specifically to complement the original equipment
immobiliser system on your Triumph motorcycle. The Triumph Protect+ is purely an alarm, the immobilisation
functionality is handled by the motorcycle ignition system.
When armed the Triumph Protect+ monitors your motorcycle for signs of unauthorised movement by use of
a movement sensor, unauthorised ignition operation and unauthorised access to the alarm control unit as
well as battery removal. If any of these conditions are detected the alarm siren will sound and the motorcycle
indicators will flash except if the motorcycle battery has been disconnected, where the siren will still sound
thanks to an internal rechargeable battery in the Triumph Protect+, but the motorcycle indicators will not
flash. The siren will operate for 29 seconds, then re-arm. This will be repeated 10 times if an alarm trigger
remains. After the activation cycle has been repeated 10 times the siren will no longer sound until the next
alarm arm/disarm.
This security system is designed as a deterrent and is not in itself a guarantee against theft. We advise you
that the more difficult you make your machine to be stolen, the lower the potential theft risk.
Applying common sense and securing your machine with additional security every time you park plays a
large part in this. Visit www.triumphmotorcycles.com for Triumph security products.
Please retain this user guide for future reference.
The information contained in this publication is accurate at the time of final approval, however, Triumph
Motorcycles reserves the right to amend the information at any time without notice.
Insurance Approval
The Triumph Protect+ is approved in the UK as a Thatcham Category 2:1 upgrade alarm, designed to be
installed on Triumph motorcycles equipped as standard with the Triumph immobiliser system.
When installed to the correct specification motorcycle, the Triumph Protect+ upgrades the motorcycle
approval to full Thatcham Category 1 status.

2 of 9
Declaration of Conformity
We, Scorpion Automotive Ltd, Dunhead Road, Chorley North Business Park, Chorley, Lancashire, PR6 7DE.
Tel: [phone] Fax: [phone] Declare that the Products:
Product name: PROTECT PLUS
Part number: 9800100, DT200
Listed above are in conformity with the following UK and UN regulations:
Radio Equipment Regulations 2017
Electrical Equipment (Safety) Regulations 2016
UNECE Regulation 10 concerning the approval of vehicles with regard to EMC (Revision 5)
Standards and type approvals comply with the above directives/regulations:
ETSI EN 300 220-1 V3.1.1:2016-11
ETSI EN 300 220-2 V3.1.1:2016-11
ETSI EN 301 489-1 V2.2.0:2017-03
ETSI EN 301 489-3 V2.1.1:2017-03
EN62479:2010
VCA Type Approval E11*10R05/01*10835*00
And we have examined the technical basis for this declaration which is based on the test reports and
certificates issued by:
ETS Ltd, Pratts Fields, Lubberhedges Lane, Stebbing, Essex, CM6 3BT
Supporting documentation relevant to this declaration will be made available on request.
This Declaration is made on behalf of Scorpion Automotive Ltd by:
Michael Nolan
Quality Manager
Date: 04/01/2021
The attention of the specifier, purchaser, installer or user is drawn to special measures and limitations to use
which must be observed when the product is taken into service to maintain compliance with the above
directives and regulations. Details available on request.

3 of 9
Contents
The Remote Control incl. Battery Replacement ........................................................................................................... 4
Operating the Triumph Protect+, Basic Functions ....................................................................................................... 5
Operating the Triumph Protect+, Advanced Features................................................................................................ 5
Troubleshooting............................................................................................................................................................................ 8
Customising the System .......................................................................................................................................................... 8
Programming Guide.................................................................................................................................................................... 8
• To Adjust the Arm/Disarm Tone............................................................................................................................. 8
• To Adjust The Automatic Rearm............................................................................................................................ 8
• To Adjust the Passive Arming Time ..................................................................................................................... 9
• To Choose the Motorcycle Battery type ............................................................................................................ 9
• To Reset the Triumph Protect+ to the Default Settings ............................................................................ 9
• To Add a new Remote control ................................................................................................................................ 9
Caution
The Triumph Protect+ is designed specifically for Triumph Motorcycles with the compatible alarm
connection plug. The Triumph Protect+ is approved for use on those motorcycles only. Modification of the
alarm wiring or control unit in any way will invalidate the granted approvals and warranty and may result in
technical failure.
Supply: 12Vdc, 4A
RF Device: 433MHz, <1mW ERP

4 of 9
The Remote Control
Note:
• In the interests of security it is not
recommended to attach the Protect+ remote
control to the motorcycle key.
Operation
The Triumph Protect+ is provided with 2 remote
controls as standard.
It is possible to add up to 4 extra remote controls (6
in total).
We recommend making use of both remote controls
from time to time, ideally alternating use every 3 to
6 months.
The left hand ‘Arm/Disarm’ button controls the
main arm/disarm functions of the system.
The right hand ‘Programming’ button is used to
initiate secondary functions such as movement
sensor deactivation (Transport Mode) and bike
finder.
When either button is pressed on the remote
control, the LED indicator will illuminate to confirm
the button has been pressed and the remote
transmitter is operating. If the LED indicator does
not illuminate when either button is pressed replace
the battery as detailed below.
1. Arm/Disarm button
2. Programming button
3. LED indicator
Replacing the Battery
Each remote control contains a single long-life
lithium battery (CR2450).
Please replace the remote battery when the range
of operation decreases noticeably.
1. To replace the battery, locate the recess in the
edge of the remote control casing and gently
prise the upper and lower sections of the
casing apart at this point.
2. The battery is retained by a clip on the remote
control circuit board and can be removed by
sliding the battery out from under the clip in
the direction shown. Fit the new battery,
ensuring the battery polarity is correct, by
sliding the battery under the retaining clip in
the direction shown.
1. Remote control circuit board
2. Retaining clip
3. Battery
3. Align the two casing halves and squeeze firmly
to click the casing back together, ensuring the
joint is even around the perimeter.
2
13
Notice
Make sure the used battery is disposed of, or
recycled in accordance with local environmental
regulations. Incorrect disposal or recycling of a
battery may result in prosecution.
Caution
When removing, or fitting a battery in the remote
control make sure it is removed or fitted in the
correct direction. Failure to remove or fit a battery
correctly could result in damage to the remote
control and possible malfunction.
Remove
Fit
2
1
3

5 of 9
Operating the Triumph Protect+,
Basic Functions
Arming (turning the Triumph Protect+ on) and
disarming (turning the Triumph Protect+ off) are the
most common interactions and can be performed
with a single button operation on the remote
control.
1. Remote control
2. Arm/Disarm button
Arming the Triumph Protect+
To manually arm the Triumph Protect+, with the
motorcycle ignition switched off press the Arm/
Disarm button on the remote control once. The
indicators will flash twice and if arm/disarm tones
are enabled, a double chirp will be heard.
The dedicated alarm LED in the motorcycle
instruments will illuminate for 3 seconds and then
flash once every second for a further 10 seconds
whilst the system initializes the tilt sensor and
trigger inputs. After 10 seconds, the Triumph
Protect+ is fully armed, and the motorcycle LED will
flash at a rate determined by the motorcycle
battery voltage, see Battery Monitoring.
Disarming the Alarm
To disarm the Triumph Protect+, press the Arm/
Disarm button once. The indicators on your
motorcycle will flash once to confirm the Triumph
Protect+ has disarmed and if the audible chirps are
enabled, a single chirp will be heard. The motorcycle
ignition can now be turned on without triggering
the Triumph Protect+. The Triumph Protect+ cannot
be re-armed within 3 seconds of disarming.
Passive Arming
With Passive Arming enabled there is no need to
press the Arm/Disarm button to arm the Triumph
Protect+. Once the motorcycle ignition is switched
off the Triumph Protect+ will arm fully after the
chosen delay period, which can be chosen by the
user from 30 seconds, 1 minute or 2 minutes. The
indicators will flash when the Triumph Protect+ is
automatically arming. Passive Arming is disabled by
default.
Operating the Triumph Protect+,
Advanced Features
In addition to the basic functions the Triumph
Protect+ also offers the following advanced
features:
• Arm silently (if tones enabled)
• Disarm silently (if tones enabled)
• Arm in Transport Mode
• Long Term Storage Mode
• Bike Finder
• Panic Alarm
• Battery Monitoring
Arm Silently
If the arm/disarm tones are enabled, it is possible to
arm the Triumph Protect+ silently by pressing the
Programming Button on the remote immediately
before pressing the Arm/Disarm button.
The buttons must be pressed within 3 seconds of
each other, the Triumph Protect+ will arm as normal
except the arming notification tones will not be
sounded. Subsequent arming sequences will not be
affected.
Disarm Silently
If the arm/disarm tones are enabled, it is possible to
disarm the Triumph Protect+ silently by pressing
the Programming Button on the remote
immediately before pressing the Arm/Disarm
button.
The buttons must be pressed within 3 seconds of
each other, the Triumph Protect+ will disarm as
normal except the disarming notification tones will
not be sounded. Subsequent disarming sequences
will not be affected.
Automatic Rearming
When enabled, the Automatic Rearming feature will
arm the Triumph Protect+ if the Triumph Protect+
has been disarmed via the two-button remote and
the ignition is not switched on within 30 seconds.
Turning on the ignition or arming via the two-
button remote will cancel the Automatic Rearming
feature. Automatic Rearming is disabled by default.
Note:
• The Triumph Protect+ will not automatically
arm as a result of the ignition being switched
off, this is known as Passive Arming.
21

6 of 9
Arm in Transport Mode
To arm the Triumph Protect+ in Transport Mode,
first press the Arm/Disarm button as normal to arm
the Triumph Protect+. Then, within 3 seconds of the
first button press, press the Programming button
which will disable the movement sensor; the
Triumph Protect+ will chirp a third time (if tones are
enabled) and the indicators will also flash a third
time to indicate the movement sensor has been
disabled.
The motorcycle instrument LED will now double
flash instead of single flash to identify Transport
Mode has been activated.
Transport Mode allows the bike to be moved around
(for example when cleaning) or transported in a van
without the Triumph Protect+ triggering due to
movement.
Note:
• Ignition detection and ECU protection switch
detection remain fully active.
To exit Transport Mode simply disarm the Triumph
Protect+ using the Arm/Disarm button and rearm
the Triumph Protect+ if required.
Long Term Storage Mode
Long Term Storage Mode, also known as ‘Winter
Mode’ is used for motorcycles that are not ridden
for long periods and which are stored securely.
When in this mode the Triumph Protect+ draws
negligible current and will only respond to the
ignition being switched on, the movement sensing
and ECU protection switch detection are
inoperative.
To enter Long Term Storage Mode, disarm the
Triumph Protect+ and with ignition off hold down
both buttons on the two-button remote for
10 seconds. A loud bleep will be heard, and the
Triumph Protect+ system will now be inactive.
To exit Long Term Storage Mode, turn the
motorcycle ignition on and the Triumph Protect+ will
sound a series of fast bleeps that rise in volume.
Press the Arm/Disarm button to disarm the
Triumph Protect+. If the Arm/Disarm button is not
pressed the Triumph Protect+ will trigger fully and
the siren will sound.
Note:
• Long Term Storage Mode should also be used to
prevent the Triumph Protect+ from triggering if
the motorcycle battery needs to be
disconnected for any reason.
Bike Finder
The Bike Finder feature flashes the directional
indicators so that the rider can identify the location
of their motorcycle from afar without disarming the
Triumph P rotect+.
Bike Finder is only operational when the Triumph
Protect+ is fully armed and can be activated by
pressing the Programming button on the remote
control for 3 seconds. The motorcycle indicators will
flash 10 times then stop.
Pressing the Programming button during the
directional indicator flashes will cause the flashing
to stop (Note: no need to press and hold).
The Triumph Protect+ cannot be disarmed whilst
the Bike Finder function is operational.
Caution
Your insurance company may not include cover
for an alarm in Long Term Storage Mode.
The level of security is reduced when the Triumph
Protect+ is in Long Term Storage Mode.
Always check the details of your insurance cover
before using the Long Term Storage Mode.
Caution
Prolonged storage of the motorcycle with the
Triumph Protect+ armed will result in battery
drain.
Excessive battery drain will cause permanent
damage to the battery.
The motorcycle should be connected to an
appropriate battery conditioner to maintain good
battery condition.

7 of 9
Panic Alarm
Note:
•ThePanicAlarmdoesnot operate with the
ignition ON.
The Triumph Protect+ offers a ‘Panic Alarm’ facility
that will cause the Triumph Protect+ siren to sound
and the motorcycle indicators to flash to attract
attention. To activate the Panic Alarm, hold down
the Arm/Disarm button on the remote control for 3
seconds with the motorcycle ignition turned off.
To cease the Panic Alarm, press the Arm/Disarm
button on the remote. The Panic Alarm will run for
approximately 5 minutes unless stopped by the
remote control.
If the Triumph Protect+ is disarmed with ignition off,
then pressing and holding the Arm/Disarm button
for 3 seconds will first arm the Triumph Protect+
before triggering the Panic Alarm. If the Triumph
Protect+ is in the armed state, then pressing and
holding the Arm/Disarm button for 3 seconds will
disarm the Triumph Protect+ before triggering the
Panic Alarm feature.
Diagnostics Bleeps
When the Triumph Protect+ is disarmed via the
remote control, a series of bleeps may be heard
signifying the Triumph Protect+ has been triggered.
The explanation for the bleeps is as follows:
•1 Bleep: Ignition on trigger
•2 Bleeps: ECU protection switch trigger
•3 Bleeps: Inclination detection trigger
•4 Bleeps: Panic Alarm
•5 Bleeps: Power supply disconnect trigger
•6 Bleeps: Inclination sensor hardware warning
•7 Bleeps: Software reboot warning
Battery Monitoring
The Triumph Protect+ monitors the motorcycle battery voltage and, when the Triumph Protect+ is armed,
flashes the motorcycle instrument LED at a variable rate to notify the measured battery voltage. The LED
flash rate is as follows:
Lead Acid Battery
1 Voltages are approximate
2 If the movement sensor is disabled, either by Transport Mode or via programming then the status LED will
flash twice in quick succession to indicate that the movement sensor has been disabled.
Lithium Battery
1 Voltages are approximate
2 If the movement sensor is disabled, either by Transport Mode or via programming then the status LED will
flash twice in quick succession to indicate that the movement sensor has been disabled.
Measured Voltage1LED Sequence2Indicative Status
Greater or equal to 11.5 V Once every 5 seconds Fully charged battery
Between 11.5 V and 10.5 V Once every 10 seconds Partially discharged battery
Less than or equal to 10.5 V Once every 20 seconds Low battery
Measured Voltage1LED Sequence2Indicative Status
Greater or equal to 13.2 V Once every 5 seconds Fully charged battery
Between 13.2 V and 12.4 V Once every 10 seconds Partially discharged battery
Less than or equal to 12.4 V Once every 20 seconds Low battery

8 of 9
Troubleshooting
If the Triumph Protect+ does not react to the
remote control when arming or disarming check the
following:
• LED Indicator is illuminating on the remote
when the Arm/Disarm button is pressed. If not
replace the remote control battery.
• Operate the remote directly adjacent to the
motorcycle in case of local radio frequency (RF)
interference.
• If a local source of RF interference is identified,
move the motorcycle away from the area and
attempt to operate the Triumph Protect+ again.
Customising the System
The Triumph Protect+ has been designed to be
simple to operate and to allow certain features to
be programmed to suit personal preference or
requirements. The user programmable options are:
• Arm/Disarm tones – quiet, loud or off (default)
• Automatic Rearming - on or off (default)
• Passive Arming at ignition off – activate at;
30 seconds, 60 seconds, 120 seconds, or off
(default)
• Battery type – lead acid (default) or lithium ion
Note:
• Sensitivity movement can only be adjusted by
a Triumph dealer, due to Thatcham approval
requirement.
Programming Guide
To customise the Triumph Protect+ features to the
user preferred options follow the programming
guides below.
To Adjust the Arm/Disarm Tone
1. Disarm the Triumph Protect+.
2. Turn on the ignition.
3. Within 10 seconds, press and hold both buttons
on the remote control.
4. After 3 seconds the Triumph Protect+ will start
to chirp. Release the remote control buttons
after the first chirp. The Triumph Protect+ will
bleep a specified number of times to indicate
the current setting.
5. Press the Arm/Disarm button on the remote
control to cycle through the tone options:
•Off (1 Bleep).
•Quiet (2 Bleeps).
•Loud (3 Bleeps).
6. Turn off the ignition to exit programming and
save the new setting.
To Adjust The Automatic Rearm
1. Disarm the Triumph Protect+.
2. Turn on the ignition.
3. Within 10 seconds, press and hold both buttons
on the remote control.
4. After 3 seconds the Triumph Protect+ will start
to chirp. Release the remote control buttons
after two chirps. The Triumph Protect+ will
bleep a specified number of times to indicate
the current setting.
5. Press the Arm/Disarm button on the remote
control to cycle through the automatic rearm
options:
•Off (1 Bleep).
•On (2 Bleeps).
6. Turn off the ignition to exit programming and
save the new setting.
Caution
It is important that the internal battery in the
Triumph Protect+ is not left in a discharged
condition.
If the Triumph Protect+ internal battery is left
discharged it will result in damage to the battery.
If the motorcycle is to be left unused for any
period beyond two weeks it should be connected
to an appropriate battery conditioner to maintain
good battery condition.
Battery issues resulting from improper
maintenance are not covered under warranty.

9 of 9
To Adjust the Passive Arming Time
1. Disarm the Triumph Protect+.
2. Turn on the ignition.
3. Within 10 seconds, press and hold both buttons
on the remote control.
4. After 3 seconds the Triumph Protect+ will start
to chirp. Release the remote control buttons
after three chirps. The Triumph Protect+ will
bleep a specified number of times to indicate
the current setting.
5. Press the Arm/Disarm button on the remote
control to cycle through the automatic arming
options:
•Off (1 Bleep).
•30 second delay (2 Bleeps).
•60 second delay (3 Bleeps).
•120 second delay (4 Bleeps).
6. Turn off the ignition to exit programming and
save the new setting.
To Choose the Motorcycle Battery type
1. Disarm the Triumph Protect+.
2. Turn on the ignition.
3. Within 10 seconds, press and hold both buttons
on the remote control.
4. After 3 seconds the Triumph Protect+ will start
to chirp. Release the remote control buttons
after four chirps. The Triumph Protect+ will
bleep a specified number of times to indicate
the current setting.
5. Press the Arm/Disarm button on the remote
control to cycle through the motorcycle
battery options:
•Lead Acid (1 Bleep).
•Lithium (2 Bleeps).
6. Turn off the ignition to exit programming and
save the new setting.
To Reset the Triumph Protect+ to the Default
Settings
1. Disarm the Triumph Protect+.
2. Turn on the ignition.
3. Within 10 seconds, press and hold both buttons
on the remote control.
4. After 3 seconds the Triumph Protect+ will start
to chirp. Release the remote control buttons
after five chirps.
5. Press the Arm/Disarm button on the remote
control once, the Triumph Protect+ will bleep
twice.
6. Press both buttons on the remote control to
save the default settings and exit
programming.
To Add a new Remote control
1. Disarm the Triumph Protect+.
2. Turn on the ignition.
3. Within 10 seconds, press and hold both buttons
on the remote control.
4. After 3 seconds the Triumph Protect+ will start
to chirp. Release the remote control buttons
after six chirps. The Triumph Protect+ will bleep
once.
5. Press the Arm/Disarm button, the Triumph
Protect+ will bleep twice.
6. Press both buttons together on the remote
control, the Triumph Protect+ will bleep twice.
Note:
• After programming the first remote control all
other remote controls will be deleted.
7. Press either button on the first remote control
to be added, the Triumph Protect+ will bleep
once.
8. Press either button on the next remote control
to be added, the Triumph Protect+ will bleep
once. Repeat the step for all additional remote
controls to be added, (maximum 6). The remote
control LED will flash to show the number of
remote controls programmed.
9. Press the Arm/Disarm button once, the alarm
will bleep once.
10. Turn off the ignition to exit programming and
save the new settings.