TRNDlabs SWIFT User manual

1
SWIFT
USER GUIDE

www.trndlabs.com

Welcome to the world of
TRNDlabs products!
TRNDlabs products are design focused electronics,
engineered to combine ulmate performance and
aesthecs.
www.trndlabs.com

4
Table of Contents
5
6
7
17
10
11
8
14
7
15
11
8
14
9
7
15
12
9
Parts Idencaon
Funcons
Photo & Video
Pairing
Pilong
Setup
Tips & Tricks
Safety Precauons
Setup App
Drone Funcons
Taking a Photo
Take-O & Land
Charging SWIFT
App Installaon
Direcon Trim
Replacing Rotor Blades
Rotaon Trim
FAQ
Calibraon
Rotor Protector Installaon
Controller Funcons
Recording a Video
Flight Controls
Controller Baery Installaon
Mobile Phone Holder Preparaon

5
21
30
26
21
31
26
28
26
29
27
27
32
32
25
22
Tips & Tricks
Safety Precauons
Troubleshoong
Sensivity Control
Addional Safety Precauons
Direcon Trim
Replacing Rotor Blades
Rotaon Trim
FAQ
Calibraon
Rotor Protector Installaon
Baery Safety Instrucons
FCC Compliance Informaon
(USA only)
Switching Modes
Advanced Flight: Performing
360º Flips

6
Parts Idencaon
SWIFT
Rotor Protectors (4x)
Replacement Rotor Blades (4x)
Controller
USB
Charging
Cable

7
Drone Funcons
Controller Funcons
Funcons
Drone Body
Rotor Blade
Camera
Rotor Protector
Take-O /
Land
Buon
Return Home
Buon
Speed/Stunt
Buon
Direcon
Forward/
Backward/
Sideways
Sideways Trim
Buons
Power Buon
Headless Mode
Buon
Throle/
Rotate
Video/Photo
Buon
Forward/Backward
Trim Buons
Power ON/OFF
Buon

8
Setup
Charging SWIFT
Connect the Charging Cable to a USB port 1 and the baery of the drone. 2
A LED light on the connector of the Charging Cable will indicate it is charging.
When the baery is fully charged, the LED light turns o. It takes about 60
minutes to recharge a discharged baery.
Slide the baery out of the drone by pulling it gently.
Make sure you only charge the rechargeable baery with the supplied
USB Charging Cable. If you try to charge the rechargeable baery
with a dierent baery charger, this might cause serious damage.
WARNING
2
2
1

9
Controller Baery Installaon
Slide the Mobile Phone Holder from
closed posion to open posion. You
can now place a mobile phone.
Mobile Phone Holder Preparaon
1 Open the Controller baery cover.
2 Install 2x 1.5V AAA baeries.
3 Slide the Controller baery cover back.
2 3
1

10
Pairing
Place the drone on a at and level surface.
1 Press the Power Buon for 2 seconds to switch the drone ON.
2 Push the Power Buon to turn on the Controller. The Green Indicator Light
on the Controller starts ashing slowly.
3The Drone will automacally connect to the Controller. Aer succesfull
binding the Controller will beep twice.
12

11
Pilong
1 Push the le sck to the lower le corner and the right sck to the lower
right corner at the same me. The rotors start spinning.
2 To take o the drone push the Take-O/Landing Buon. The drone will hover
at approximately 1 meter.
When ying, push the Take-O/Landing Buon again to land the drone.
In case of an emergency, push and hold the le and right sck as described
in step 1.
Take-O & Land
Throle Control
To y higher, push the Throle/Rotate sck cauously forward. To y lower, push
the Throle/Rotate sck cauously backward.
2
1
1
2
1

12
Flight Controls
Direcon Control
To y the drone forward or backward, push the Direcon sck cauously
forward or backward.
To y the drone to the le or the right, push the Direcon sck cauously to
the le or the right.

13
Rotaon Control
To make the drone circle to the le or the right, push the Throle/Rotate sck
cauously to the le or right.

14
Setup App
App Installaon
The App is suitable for mobile phones with iOS or Android. The App can be
downloaded from the App Store or Google Play.
Scan the QR code to download the App: TRNDlabs SWIFT
For mobile phones with
iOS, search TRNDlabs
SWIFT in the App
Store.
For mobile phones
with Android, search
TRNDlabs SWIFT in
Google Play.

15
Photo & Video
Taking a Photo
Recording a Video
Press the Photo Buon once to take a photo.
Press the Video Buon on the controller for 3 seconds to start recording. Press
the buon again for 3 seconds to stop recording.

16
Tips & Tricks
Sensivity Control
Controller Sensivity Control
The drone has three sensivity sengs: Low, Medium and High. A higher
sensivity makes the drone faster and more responsive.
Press the Sensivity/Stunt Buon to change the sensivity:
1 When the Controller emits 1 tone = Low sensivity mode.
2 When the Controller emits 2 tones = Medium sensivity mode.
3 When the Controller emits 3 tones = High sensivity mode.

17
Advanced Flight: Performing 360° Flips
1 Press and hold the Sensivity/Stunt Buon to enter stunt mode. The
Controller will start to beep fast.
2 Push the Direcon sck forward, backward, right or le to perform ips.
The drone carries out the ip in the respecve direcon.
Do not aempt these stunts unl you are able to y condently.
Choose an area that will provide a so landing (carpet or grass) and
maintain an altude of at least 10 feet/3 meter to allow room to
recover control as you pracce ipping the drone.
WARNING
2
1

18
Le Side 360° Flip
Press the Sensivity/Stunt Buon and push the Direcon sck to the le.
Right Side 360° Flip
Press the Direcon sck and push it to the right.
1
1

19
Forward 360° Flip
Press the Direcon sck and push it forward.
Backward 360° Flip
Press the Direcon sck and push it backward.
1
1

20
Switching Modes
The drone can be switched from Normal Mode A to Headless Mode. BHeadless
Mode does not require the pilot to dierenate the front (head) posion of the
drone, but simply use the Direcon Sck for the drone to respond correctly to
the given input relave to the posion of the controller.
To enter Headless Mode, press buon 1. The controller will emit a double
beeping sound to conrm the drone is now in headless mode. Press buon 1
again to exit Headless Mode. The controller emits a beep tone again to conrm
return to Normal Mode.
A
B
1