Trotec TTV 4500 S User manual

TRT-BA-TTV 4500 S-TC2015-11-002-EN
TTV 4500 S
EN
ORIGINAL INSTRUCTIONS
AXIAL FAN

2 EN
axial fan TTV 4500 S
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................5
Assembly and start-up..........................................................5
Operation ...............................................................................6
Available accessories............................................................6
Errors and faults....................................................................6
Maintenance ..........................................................................7
Technical annex.....................................................................8
Disposal ...............................................................................10
Declaration of conformity ...................................................10
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
Wear hearing protection
Information marked with this symbol indicates that you
should wear hearing protection.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
TTV 4500 S
https://hub.trotec.com/?id=42954
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• During normal operation an air transport hose or dust bag
can be connected to the air outlet opening.
• For an increased performance up to 3 devices may be
operated in batch mode, i.e. stacked on top of one another
during operation. If so, no further accessories such as air
transport hose or dust bag must be used.
• Up to 4 fans can be connected in series by means of the
connection pieces.
• Observe a minimum distance of 3m between walls,
objects and the suction side.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.

EN 3
axial fan TTV 4500 S
• Do not sit on the device.
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Never point the switched-on device at people or animals.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the technical data when selecting extensions to
the power cable. Completely unroll the extension cable.
Avoid electrical overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
• When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
• Make sure that the air inlet and outlet are not obstructed.
• Make sure that there are no loose items or dirt located in
the immediate surroundings of air inlet and air outlet.
• Protect yourself and your environment from whirled up
parts.
• Improper installation can lead to a fire, electric shock or
severe personal injury.
Intended use
The axial fan TTV 4500 S may be used for aeration, deaeration,
air circulation, dust collection or air transport whilst adhering to
the technical data and the safety instructions.
The device was designed for the generation of a powerful,
large-volume air circulation, e.g. for the accelerated drying of
buildings and rooms. The fan can be operated in combination
with different accessories.
Improper use
The axial fan TTV 4500 S is not suited for installation in fluids or
on flooded or boggy grounds.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personal protective equipment
Wear hearing protection
Wear appropriate hearing protection when working
with the device.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when using
high-performance fans.
• have read and understood the instructions, especially the
Safety chapter.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

4 EN
axial fan TTV 4500 S
Caution
Risk of injury due to parts being whirled up by the
strong air current.
Before switching the device on, make sure that there
are no loose parts (clothing, hair etc.) located near the
air inlet or outlet!
Caution
Keep a minimum distance of 3m to the suction side of
the device!
Note
Do not use abrasive cleaners or solvents to clean the
device.
Behaviour in the event of an emergency
1. Immediately switch the device off via the main emergency
stop switch or the emergency stop at the upstream
distributor.
2. Remove persons from the danger area.
3. Disconnect the device from the electric circuit.
4. Do not reconnect a defective device to the mains.
Information about the device
Device description
The axial fan TTV 4500 S was designed for a very high air flow
rate.
The high air volume flow and a variety of configuration options
enable its flexible application ranging from construction drying,
e.g. in combination with a condenser dryer, to the large-volume
air transport even in dusty surroundings.
The cable of this device can be wound around the hose
connection. The TTV 4500 S is further equipped with a service
socket, which means that you can operate another device,
e.g. another TTV4500S, in cascaded operation via the same
socket. This socket is ready for operation for as long as the first
device is connected to the mains – it does not need to be
switched on.
The integrated operating hours counter can be used for the
settlement with an insurance company or for construction site
calculations.
Device depiction
1
3
4
6
5
7
2
No. Designation
1 air outlet
2 air hose (optional)
3 mains power cable with Schuko plug
4 connection pieces
5 air inlet
6 control panel
7 transport handle

EN 5
axial fan TTV 4500 S
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
To make the device easier to transport, it is fitted with a carry
handle.
Before transporting the device, observe the following:
• Switch off the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Do not use the power cable to drag the device.
After transporting the device, observe the following:
• Set up the device in an upright position after transport.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust, if necessary
• stackable: up to 3devices may be stacked on top of one
another
Info
Do not take the devices into operation when stacked.
Stacking rules out an efficient usage of the devices.
Assembly and start-up
Scope of delivery
• 1x Device
• 1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
Assembly
1. Assemble the device according to the desired area of
application along with other devices or accessories.
ðAlways use a tension belt to connect hoses or dust
bags.
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
A
B
C
C
D
• Set the device up in an upright and stable position.
Individually, the axial fan can be installed at an inclination
angle of up to 15°.
• Make sure the device is only placed on firm, dry and
vibration-free ground.
• When positioning the device, keep a sufficient distance to
heat sources.
• Up to four devices can be connected in series for
operation.
• Make sure that the air inlet and outlet are not obstructed.
• Make sure that extension cables are completely unrolled.

6 EN
axial fan TTV 4500 S
Connecting the power cable
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Unwind the power cable.
• Insert the mains plug into a properly secured mains
socket.
Operation
Operating elements
893
No. Designation
3 mains power cable
8 on/off step switch I - 0 - II
9 operating hours counter
Switching the device on
üThe device has been completely installed as described in
the Assembly and start-up chapter.
1. Actuate the on/off switch(8) to switch the device on, thus
choosing the desired air volume flow level:
ðstageI: approx.4,350m3/h
ðstageII: approx.5,000 m3/h
Shutdown
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off by setting the on/off step switch(8)
to position0.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Clean the device according to the Maintenance chapter.
• Store the device according to the Storage chapter.
Available accessories
Warning
Only use accessories and additional equipment
specified in the instructions.
Using insertion tools or accessories other than those
specified in the instructions may cause a risk of injury.
TTV 4500 S
Designation Article number
Tilt frame 6.100.005.005
Air transport hose Tronect SP-T,
length: 7.6m 6.100.001.216
Dust bag class M, length: 5m 7.160.000.112
Universal lashing strap 6.100.001.995
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
The fan is not running:
• Check whether the device is switched on.
• Check the power connection.
• Check the power cable and mains plug for damages.
• Check the on-site fusing.
The fan operates only for a brief period, then switches off:
• Check whether the protective grid at the air inlet is
obstructed in some way. If applicable, remove foreign
objects.
• The motor bearing might be damaged. Please contact the
customer service.
The motor or fan is noisy or runs unevenly:
• The fan is soiled. Clean the fan according to the
Maintenance chapter.
• The fan or the blower unit is damaged. Please contact the
customer service. If necessary, bring the device to an
authorized specialist electrical company or to Trotec for
repair.
• The motor bearing might be damaged. Please contact the
customer service. If necessary, bring the device to an
authorized specialist electrical company or to Trotec for
repair.
The fan produces grinding noises:
• The fan blades are dirty or foreign objects are located in
the rotation range of the fan. Clean the fan blades or the
blower unit according to the Maintenance chapter.
• The fan blades might be damaged. Please contact the
customer service. If necessary, bring the device to an
authorized specialist electrical company or to Trotec for
repair.

EN 7
axial fan TTV 4500 S
The device vibrates heavily:
• Check the floor space of the fan. Position the device on a
level and firm surface.
• Check the screwed connections, particularly between
blower unit and foot. If necessary, retighten the screws.
• Check the fan blades for dirt and clean them if required.
• There might be an imbalance in the fan blades. Please
contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
The air flow rate is low:
• Check whether the protective grid is blocked and clean it
if required.
Note
Wait for at least 3 minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
Maintenance
Activities required before starting maintenance
Warning of electrical voltage
Do not touch the mains plug with wet or damp hands.
• Switch the device off.
• Always be mindful of atypical sounds and consult a
specialist dealer if in doubt.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
Warning of electrical voltage
Tasks which require the housing to be opened
must only be carried out by authorised specialist
companies or by Trotec.
Cleaning the housing
Clean the housing with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Protect electrical
components from moisture. Do not use any aggressive cleaning
agents such as cleaning sprays, solvents, alcohol-based or
abrasive cleaners to dampen the cloth.
Cleaning the fan and device interior
Warning
Risk of injury caused by ejected compressed air upon
activation of the compressed air supply.
Hold the compressed-air hose away from your body.
Pointing the compressed-air hose at another person is
prohibited.
• Check fan and protective grid for perfect condition before
and after each application.
• Clean the fan after each operation.
• Use compressed air to remove particles, lint, dust and dirt
from motor, fan wheel and protective grid. Do not in any
event use a high-pressure cleaner to clean the fan.
• Regularly check the housing for its perfect condition or for
defects.
• Other than that, the device does not require maintenance.

8 EN
axial fan TTV 4500 S
Technical annex
Technical data
Parameter Value
Model TTV4500S
Article number 1.510.000.013
Air volume stage1 approx.4,350m3/h
Air volume stage2 approx.5,000 m3/h
Air pressure 130 Pa
Max. sound level
(at a distance of 3m) 74dB(A)
Air current blowing out/ sucking in
Air discharge velocity 11m/s (39.6km/h)
Mains connection 1/N/PE~ 230V/ 50Hz
Current consumption 1.7A
Power input 0.33 kW
Fusing 10 A
Transport medium temperature 45°C
Hose connector 480mmØ
Type of protection IP 44
Housing plastic
Mobility portable/ stackable
Weight 15 kg
Minimum distance to walls and
other objects
top (A):
rear/ suction side(B):
sides (C):
front (D):
0.5 m
3 m
0.5 m
0.5 m
Dimensions
(length x width x depth) 330x 530x 560 mm
Circuit diagram
YELLOW/GREEN M230VAC/50Hz
BROWN
BLACK
BLUE
WHITE
WHITE
CAPACITY
SWITCH

EN 9
axial fan TTV 4500 S
Overview and list of spare parts Note!
The position numbers of the spare parts differ from those
describing the positions of other parts mentioned in this
operating manual.
No. Spare part Qty.
1 Metal Grill 2
2 Fan Blade 1
3 Motor 1
4 Plastic Housing 1
5 Rubber 12
6 Switch Panel 1
7 Switch 1
No. Spare part Qty.
8 Mechanical Timer 1
9 Wire Connector 1
10 Capacitor 1
11 Rubber Connector 1
12 Rubber Fix 1
13 Rubber Nail 1
14 Power Cord 1

10 EN
axial fan TTV 4500 S
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Declaration of conformity
The text below sets out the contents of the declaration of
conformity. The signed declaration of conformity can be found
at https://hub.trotec.com/?id=42954 .
Declaration of conformity
In accordance with the ECMachinery Directive 2006/42/EC,
AnnexII, part1, SectionA
Herewith, we– Trotec GmbH&Co.KG– declare that the
machinery designated below was developed, constructed and
produced in compliance with the requirements of the
ECMachinery Directive in the version 2006/42/EC.
Product model/ Product: TTV 4500 S
Product type: axial fan
Year of manufacture as of: 2019
Relevant EU directives:
• 2014/30/EU: 29March 2014
• 2014/35/EU:8 September 2017
Applied harmonised standards:
• EN 55014-1:2006/A1:2009
• EN 55014-1:2006/A2:2011
• EN 55014-2:1997/A1:2001
• EN 55014-2:1997/A2:2008
• EN61000-3-2:2014
• EN 61000-3-3:2013
Applied national standards and technical specifications:
• EN 61000-4-2:2009
• EN 61000-4-4:2012
• EN 61000-4-5:2006
• EN 61000-4-6:2014
• EN 61000-4-11:2004
Manufacturer and name of the authorised representative of
the technical documentation:
Trotec GmbH & Co. KG
Grebbener Straße 7, D-52525 Heinsberg
Phone: [phone]
E-mail: [email protected]
Place and date of issue:
Heinsberg, 12.05.2014
Detlef von der Lieck, Managing Director

Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com