Trotec B 3 e User manual

TRT-BA-B3E/B4E-TC210914TTRT02-001-EN

B 3 E / B 4 E

OPERATING MANUAL

HUMIDIFIER

2 EN

humidifier B 3 E / B 4 E

Table of contents

Notes regarding the operating manual.................................2

Safety .....................................................................................2

Information about the device................................................4

Transport and storage...........................................................5

Assembly and installation.....................................................6

Operation ...............................................................................8

Available accessories............................................................9

Errors and faults....................................................................9

Maintenance ........................................................................11

Technical annex...................................................................16

Disposal ...............................................................................16

Notes regarding the operating manual

Symbols

Warning of electrical voltage

This symbol indicates dangers to the life and health of

persons due to electrical voltage.

Warning

This signal word indicates a hazard with an average

risk level which, if not avoided, can result in serious

injury or death.

Caution

This signal word indicates a hazard with a low risk

level which, if not avoided, can result in minor or

moderate injury.

Note

This signal word indicates important information (e.g.

material damage), but does not indicate hazards.

Info

Information marked with this symbol helps you to carry

out your tasks quickly and safely.

Follow the manual

Information marked with this symbol indicates that the

operating manual must be observed.

You can download the current version of the operating manual

and the EU declaration of conformity via the following link:

B 3 E

B 4 E

https://hub.trotec.com/?id=45837

Safety

Read this manual carefully before starting or using the

device. Always store the manual in the immediate vicinity

of the device or its site of use.

Warning

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may

result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future

reference.

This appliance can be used by children aged from

8years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe

way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

• Do not use the device in potentially explosive rooms or

areas and do not install it there.

• Do not use the device in aggressive atmosphere.

• Only put up the device in an upright, stable position on firm

ground.

• Do not expose the device to directly squirting water.

• Fill the device with clear drinking water only.

• Never insert any objects or limbs into the device.

• Do not cover the device during operation.

• Do not sit on the device.

• This appliance is not a toy. Keep away from children and

animals. Do not leave the device unattended during

operation.

• Ensure that all electric cables outside of the device are

protected from damage (e.g. caused by animals). Never

use the device if electric cables or the power connection

are damaged!

• The mains connection must correspond to the

specifications in the Technical annex.

EN 3

humidifier B 3 E / B 4 E

• Insert the mains plug into a properly fused mains socket.

• Observe the device's power input, cable length and

intended use when selecting extensions to the power

cable. Completely unroll extension cables. Avoid electrical

overload.

• Before carrying out maintenance, care or repair work on

the device, remove the mains plug from the mains socket.

Hold onto the mains plug while doing so.

• Switch the device off and disconnect the power cable from

the mains socket when the device is not in use.

• Make sure that the air inlet and outlet are not obstructed.

• Make sure that the suction side is kept free of dirt and

loose objects.

• Do not remove any safety signs, stickers or labels from the

device. Keep all safety signs, stickers and labels in legible

condition.

• Do not use the device when the water tank is empty.

• Before filling the water tank, switch the device off and

disconnect the power cable from the mains socket. Hold

onto the mains plug while doing so.

• Only transport the device in an upright position with an

emptied water tank.

• Empty and clean the water tank prior to storage or

transport. Do not drink the water. Health hazard!

• Do not touch the water and parts inside the water tank

when the device is switched on.

• Do not touch the surface of the device with sharp, hard

objects. This may cause deformations and damage.

• Make sure that objects in the surroundings of the device

do not become wet or damp. If moisture is present, the

output must be reduced. Set the device to a lower level. If

the output cannot be reduced, the device must only be

operated in intervals. If necessary, switch the device off

completely for a short time. Ensure that absorbent

materials such as carpeting, curtains, sheers or tablecloths

will not become damp.

• Note that high humidity levels may enhance the growth of

biological organisms in the environment.

• Make sure that the water in the water thank is replaced

every3days. Otherwise there is a risk of microorganisms

growing in the water tank which presents a health hazard

if they get into the air or water.

• Do not fill the device with water by the air inlet or outlet.

• Do not position the device near stoves or fireplaces. Avoid

direct solar radiation.

• This device contains a UVlamp. Do not look into the light

source for too long.

• A damaged housing or misuse can cause UV-C radiation

leakage. UV-C radiation is hazardous even in small

amounts and can cause injuries of the eyes and skin.

Intended use

Only use the device as a mobile humidifier for the humidification

and filtration of room air, while adhering to and following the

technical data.

Intended use comprises humidifying the room air in:

• living spaces

• warehouses and archives

• libraries

• call centres and computer rooms

Foreseeable misuse

• The device is not intended for industrial use.

• Do not place the device on wet or flooded ground.

• Do not place any objects, e.g. clothing, on the device.

• Do not use the device out of doors.

• Do not make any unauthorised modifications, alterations or

structural changes to the device.

• Any use other than the intended use is regarded as a

reasonably foreseeable misuse.

Personnel qualifications

People who use this device must:

• be aware of the dangers that occur when working with

electric devices in damp areas.

• have read and understood the operating manual, especially

the Safety chapter.

Safety signs and labels on the device

Note

Do not remove any safety signs, stickers or labels from

the device. Keep all safety signs, stickers and labels in

legible condition.

The following safety signs and labels are attached to the device:

Symbols Meaning

This symbol located on the device indicates that

the water tank should be cleaned every3days.

Change the water in the water tank every3days.

Disconnect the device from the mains before

cleaning the water tank.

Operate the device with the adapter supplied by the

manufacturer.

Residual risks

Warning of electrical voltage

Work on the electrical components must only be

carried out by an authorised specialist company!

4 EN

humidifier B 3 E / B 4 E

Warning of electrical voltage

Before any work on the device, remove the mains plug

from the mains socket!

Do not touch the mains plug with wet or damp hands.

Hold onto the mains plug while pulling the power cable

out of the mains socket.

Warning

Dangers can occur at the device when it is used by

untrained people in an unprofessional or improper way!

Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the

hands of children.

Warning

Risk of suffocation!

Do not leave the packaging lying around. Children may

use it as a dangerous toy.

Caution

If the device is knocked over, water will leak from the

lower part.

Disconnect the device from the mains to prevent

damage to the device caused by dry running.

Note

Do not operate the device without an air filter inserted

into the air inlet!

Without the air filter, the inside of the device will be

heavily contaminated. This could reduce the

performance and result in damage to the device.

Behaviour in the event of an emergency

1. Switch the device off.

2. In an emergency, disconnect the device from the mains

feed-in: Hold onto the mains plug while pulling the power

cable out of the mains socket.

3. Do not reconnect a defective device to the mains.

Information about the device

Device description

The device B 3 E/B 4 E functions as a humidifier, aroma diffuser

and air cleaner.

The ultrasound technology ensures a pleasant room climate and

air quality improvement.

The capacity of the water tank of4.2l allows for a running time

of approx.16hours.

The device switches off automatically when the water tank is

empty.

Scented oil can be added to the scented oil tank for optional

room air aromatization.

The device is provided with a timer function that can be

programmed for automatic switch-off after 2to12 hours.

An integrated anti-bacterial UV lamp reduces bacteria in the

bottom section of the device.

Device depiction

EN 5

humidifier B 3 E / B 4 E

No. Designation

1Lid with air outlet

2Air outlet

3Water level indicator

4Water tank

5Bottom section

6Control panel

7Mains connection(adapter)

8Cover with carbon filter(air filter)

9Cover for water filter

10 Valve unit

11 Air nozzle

12 Nebulizer membrane

13 Float

14 UV lamp

15 SecoSan® Stick 10 (optional accessory)

Transport and storage

Note

If you store or transport the device improperly, the

device may be damaged.

Note the information regarding transport and storage of

the device.

Transport

Before transporting the device, observe the following:

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Lift the device at the lower part.

• Empty the water tank.

• Empty the lower part.

• Do not use the power cable to drag the device.

• Check whether the upper part is correctly positioned on

the lower part.

After transporting the device, proceed as follows:

• Set up the device in an upright position after transport.

Storage

Before storing the device, proceed as follows:

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the water tank.

• Empty the lower part.

• Use a cloth to wipe all parts of the device dry.

• Clean the device according to the Maintenance chapter.

When the device is not being used, observe the following

storage conditions:

• dry and protected from frost and heat

• in an upright position where it is protected from dust and

direct sunlight

• with a cover to protect it from invasive dust, if necessary

• Place no further devices or objects on top of the device to

prevent it from being damaged.

6 EN

humidifier B 3 E / B 4 E

Assembly and installation

Scope of delivery

• 1x Device

• 1x Adapter

• 1x Manual

Unpacking the device

1. Open the cardboard box and take the device out.

2. Completely remove the packaging.

3. Fully unwind the power cable. Make sure that the power

cable is not damaged and that you do not damage it during

unwinding.

Start-up

• Before restarting the device, check the condition of the

power cable. If there are doubts as to the sound condition,

contact the customer service.

• Only put up the device in an upright, stable position on firm

ground.

• Do not create tripping hazards when laying the power

cable or other electric cables, especially when positioning

the device in the middle of the room. Use cable bridges.

• Make sure that extension cables are completely unrolled.

• Make sure that there are no moisture-sensitive objects in

the immediate vicinity of the mist nozzle, since water may

condense near the mist nozzle.

Filling the water tank

The water tank(4) should be filled with clear drinking water

before first use.

Note

Fill the device with clear drinking water only. The water

temperature must not exceed40°C.

Scented oil or other additives can damage the plastics

and the nebulizer membrane.

Info

If possible, change the water every3days to prevent

bacterial growth.

Info

The low water level LED(20) flashes permanently

when the water level in the water tank(4) is too low.

Info

The low water level LED(20) flashes three times in

succession when the water tank(4) is empty. The dry-

run protection is activated.

1. Open the lid with air outlet(1).

2. Fill clear drinking water(maximally40°C) up to the MAX

indication into the water tank(4).

3. Insert the SecoSan® Stick (optional accessory)(15) into the

water tank(4).

4. Now close the lid with air outlet(1). Ensure that the lid is

aligned correctly.

EN 7

humidifier B 3 E / B 4 E

Scent option

Additionally, the device offers the possibility to distribute a scent

during operation.

Note

Never put scented oil into the water tank, on the

ultrasonic membrane or on other parts of the device.

Direct contact with scented oil might cause damage to

plastic components or other device parts.

Use standard scented oil. Proceed as follows to use the scent

option:

üThe device is switched off and the power cable is

disconnected from the mains.

1. Remove the cover with carbon filter (8) with the integrated

scented oil tank(16) from the device by carefully pushing

against the lower edge of the cover.

ðThe cover(8) is unlocked from the bottom section(5).

2. Put2 to3drops of scented oil onto the fleece in the

scented oil tank.

3. Refit the cover with carbon filter(8) into the housing.

ðThe cover(8) is locked audibly in the bottom section(5).

Inserting the air filter

Note

Do not operate the device without an air filter inserted

into the air inlet!

Without the air filter, the inside of the device will be

heavily contaminated. This could reduce the

performance and result in damage to the device.

• Make sure that the air filter is installed before switching

the device on.

1. Remove the cover(8) from the device by carefully pushing

against the lower edge of the cover.

ðThe cover(8) is unlocked from the bottom section(5).

2. Insert the carbon filter(17) into the cover.

3. Slide the cover(8) into the bottom section(5).

ðThe cover(8) is locked audibly in the bottom section(5).

Connecting the power adapter

• Plug the power adapter cable into the mains connection(7)

of the device.

• Plug the power adapter into a properly fused mains socket.

8 EN

humidifier B 3 E / B 4 E

Operation

• Avoid open doors and windows.

• Make sure that there are no moisture-sensitive objects

located in the immediate vicinity of the mist nozzle, since

water may condense near the mist nozzle.

Operating elements

No. Designation Meaning

18 Timer LEDs Indicates the selected number of

hours (2-12h in combination from

the symbols 2h, 4h, 6h. The sum of

the symbols indicates the desired

number of hours.)

19 UV lamp LED Is illuminated when the UV lamp is

activated

20 Low water level

LED

Flashes permanently when water

tank is low

Flashes 3times in succession when

the dry run protection is activated

21 On/off LED Illuminated when the device is

switched on

22 Timer button Switching the timer function on or off

23 UV lamp button For switching the UV lamp on or off

24 On/off button For switching the device on or off

25 Water level

indicator button

For switching the water level

indication lamp on or off

26 Nebulizer intensity

button

Select nebulizer intensity

27 Nebulizer intensity

LEDs

Indicate the nebulizer intensity

selected (level 1, 2 or 3)

Switching the device on

Info

If no operational input is made for40s, the control

panel(6) switches off.

1. Make sure that the water tank(4) has been filled with

drinking water.

2. Make sure that the device is neither damp nor wet on the

outside. Otherwise wipe it dry.

3. Press the On/off button(24).

ðThe nebulizer intensity LED(27) indicates the nebulizer

intensity at level1 an .

ðThe device starts to humidify. Fine water mist leaves the

mist nozzle(2).

Setting the nebulizer intensity

The nebulizer intensity can be set to 3levels:

• Stage1: Low nebulizer intensity

• Stage2: Medium nebulizer intensity

• Stage3: High nebulizer intensity

üThe device is switched on.

1. Press the Nebulizer intensity button(26).

ðLED "1” of the nebulizer intensity LEDs(27), is

illuminated for the first level.

2. Repeat the process for stage2 or3.

ðThe device now operates with the desired nebulizer

intensity.

Setting the operating mode

You can select the following operating mode:

• Manual humidification

Manual humidification

The nebulizer intensity can be set to level1–3 in this operating

mode at any time(continuous humidification regardless of the

humidity level in the room).

Timer function

For the device to switch off automatically after a predefined

number of hours (2 to 12h) you can program the timer. The

timer can be programmed in increments of 2hours.

Automatic switch-off

1. Press the timer button(22) once to program the timer to

2hours.

ðLED “2”of the timer LEDs(18) is illuminated.

ðThe device switches off automatically after 2hours.

2. Press the timer button(22) again to program the timer to

up to 12hours.

ðThe desired number of hours lights up as a combination

of the three LEDs.

Notes regarding automatic switch-off:

• Pressing the On/off button(24) deactivates the automatic

switch-off function.

EN 9

humidifier B 3 E / B 4 E

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch the device off.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the water tank.

• Empty the lower part.

• Use a cloth to wipe all parts of the device dry.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Transport and storage

chapter.

Available accessories

Warning

Only use accessories and additional equipment

specified in the operating manual.

Using insertion tools or accessories other than those

specified in the operating manual may cause a risk of

injury.

Designation Article number

SecoSan® Stick10 6.100.004.110

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damage.

• Check the on-site fusing.

• Check whether the water tank indicator light is illuminated.

The water tank might be empty and need refilling.

• Wait for 10minutes before restarting the device. If the

device is not starting, have the electrics checked by a

specialist company or by Trotec.

The device is running, but there is no formation of mist:

• Check whether the water tank indicator light is illuminated.

The water tank might be empty and need refilling.

• Check the valve in the bottom of the water tank. The valve

must be able to move freely. Clean the water tank if

required.

• Check the float in the lower part of the device. The float

should be able to move freely.

• Check the air filter for dirt. Clean the air filter if required.

• Check the nebulizer intensity setting and increase it if

required.

• Check the nebulizer membrane in the lower part of the

device for dirt and clean it if required.

The water tank is full, but the device indicates an empty

water tank:

• Heavy deposits on the filter may prevent the water from

flowing from the water tank into the bottom section. This

can occur if the device has been out of use for a long time.

Clean the filter as described in the “Cleaning the filter”

section.

• Check the valve in the bottom of the water tank. The valve

must be able to move freely. Clean the valve and water

tank if required.

Water is leaking:

• Check whether the device is set up in a stable and upright

position.

• Check the water level in the lower part of the device. The

water level might be too high and water is discharged via

the overflow.

• Check the valve in the bottom of the water tank. The valve

must be able to move freely. If required, clean the valve as

described in the “Cleaning the valve unit” section.

• Check the float in the lower part of the device. The float

should be able to move freely. It may block and cause

water to be discharged via the overflow.

10 EN

humidifier B 3 E / B 4 E

• Check the device for leaks.

The water mist has a peculiar smell:

• The device is new. Remove and rinse the water tank. Let

the open water tank air for some hours.

• Check the water tank. There may be stale or dirty water in

the water tank. Rinse the water tank and fill it with clear

drinking water.

Condensate forms on the device:

• The air circulation in the room is insufficient. If necessary,

reduce the nebulizer intensity and provide better air

circulation (e.g. using a fan).

• The room's humidity level is quite high. This makes it

difficult for the mist to distribute and leads to water

condensing on the device. If necessary, reduce the

nebulizer intensity or switch off the device.

The device is loud or vibrates heavily:

• Check whether the device is set up in a stable and upright

position.

The device still does not operate correctly after these

checks:

Please contact the customer service. If necessary, bring the

device to an authorised specialist electrical company or to

Trotec for repair.

Table of faults

The following faults can be displayed on the control panel(6):

Error Meaning

The low water levelLED (20)

flashes permanently.

The water level in the water

tank is low.

The low water levelLED (20)

flashes three times in

succession.

The water tank is empty or not

installed correctly. The dry-run

protection has been activated

EN 11

humidifier B 3 E / B 4 E

Maintenance Maintenance intervals

Maintenance and care interval before every

start-up

as needed every3days at least every

2 weeks

at least every

4 weeks

at least every

6 months

at least

annually

Check for damage X

Visually check the inside of the device

for dirt

X X

Check air inlets and outlets for dirt and

foreign objects and clean ifnecessary

X X

Clean the exterior X X

Cleaning the water tank X

Check the nebulizer membrane for dirt

and clean it, ifnecessary

X X

Check the valve unit for dirt and clean

it, ifnecessary

X X

Check the air filter for dirt and foreign

objects and clean or replace if

necessary

X X

Clean the scented oil tank X

Test run X

Maintenance and care log

Device type: ............................................. Device number: ....................................

Maintenance and care interval 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Check for damage

Visually check the inside of the device

for dirt

Check air inlets and outlets for dirt and

foreign objects and clean ifnecessary

Clean the exterior

Cleaning the water tank

Check the nebulizer membrane for dirt

and clean it, ifnecessary

Check the valve unit for dirt and clean it,

ifnecessary

Check the air filter for dirt and foreign

objects and clean or replace if necessary

Visually check the inside of the device

for dirt

Clean the scented oil tank

Test run

1. Date: ...........................................

Signature: ........................................

2. Date: ............................................