Trotec 8016 Speedy 100 fiber User manual

OPERATION MANUAL
8016Trotec Speedy 100 fiber

Trotec Laser GmbH
Linzer Strasse 156
A –4600 Wels
AUSTRIA
Ph.: ++43/7242/239-0
E-Mail: [email protected]
www.troteclaser.com
Trotec cannot be held responsible for any direct or indirect damages, which result from using or
working with the products electric circuits or software described herein. The apparatus must be used
only by trained and skilled personnel. Before use the manual should be read and followed carefully.
Furthermore Trotec reserves the right to change or alter any product described herein without prior
notice.
In case of failure, please check the device first according to section 6.2 - Tips for Troubleshooting.
If unsuccessful, please note all data of the device (year of manufacture, software version, etc.) and
call us from a telephone next to the switched on device.
For queries or technical problems please contact your dealer or Trotec directly at the above address.
This documentation with all illustrations is intellectual property of Trotec Laser GmbH.
The entire documentation is given to the user for personal use only. This documentation must not be
reproduced or made available to others without our written permission. Any breach of law will be
prosecuted.

BA 8016_2.0_EN(10/2016) 3 / 55
TABLE OF CONTENTS
1 GENERAL.............................................................................................................. 5
1.1 Operation Manual Use –General Information.........................................................5
1.2 Designated Use.........................................................................................................6
1.3 Disposal remarks......................................................................................................6
1.4 Technical Data / System Specification....................................................................7
1.5 Manufacturer's Label................................................................................................8
1.6 EU –Declaration of conformity................................................................................9
2 SAFETY ................................................................................................................10
2.1 General Safety Information....................................................................................10
2.2 Laser Safety Information........................................................................................12
2.3 Safety Precautions when Operating the Machine ................................................14
2.4 Warning and Information Labels ...........................................................................15
3 BEFORE OPERATION .........................................................................................17
3.1 Unpacking...............................................................................................................17
3.2 Contents of Delivery...............................................................................................18
3.3 Location...................................................................................................................19
3.4 Exhaust System –Requirements...........................................................................20
3.5 Computer –Requirements.....................................................................................20
3.6 Connections............................................................................................................21
3.6.1 Connecting the Mains............................................................................................21
3.6.2 Connecting the Computer......................................................................................22
3.6.3 Connecting the Exhaust System............................................................................23
4 OPERATION .........................................................................................................24
4.1 Machine view and connections .............................................................................24
4.2 Power switch (ON / OFF)........................................................................................30
4.3 Keypad ....................................................................................................................31
4.4 First Steps before Marking.....................................................................................35
4.4.1 Lateral Air Assist....................................................................................................38
4.5 First Marking Tests.................................................................................................39
5 MAINTENANCE....................................................................................................41
5.1 Cleaning the System...............................................................................................41
5.2 Cleaning the Optical Parts .....................................................................................42
5.2.1 CLEANING THE LENS..........................................................................................42
5.2.2 CLEANING THE MIRRORS ..................................................................................44
5.3 Maintenance Plan ...................................................................................................46
6 ADDITIONAL INFORMATION ..............................................................................47
6.1 Material Table..........................................................................................................47
6.2 Tips for Troubleshooting .......................................................................................49
6.3 Acceptance report ..................................................................................................50
6.4 TRAINING SCHEDULE............................................................................................51

BA 8016_2.0_EN(10/2016) 4 / 55
6.5 Response Form.......................................................................................................52
6.6 How to create a Service File...................................................................................53

BA 8016_2.0_EN(10/2016) 5 / 55
1 GENERAL
1.1 Operation Manual Use –General Information
Caution:
Please read and follow the instruction in this Operation Manual carefully, before installation and
operation. Damage to persons and/or material can result from not following individual points of the
Operation Manual!
Operation of the system is only permitted with equipment and spare parts supplied or listed in the
spare parts and consumables lists.
Auxiliary equipment must be adjusted to the base machine (any queries to dealer or manufacturer).
The following symbols are used for easier understanding of the Operation Manual:
If the Operation Manual is not observed, this area represents a particular
danger for the operating personnel or the personnel responsible for
maintenance.
Caution: This component is under voltage. In these areas strictly observe the
safety instructions regarding electricity. Care is to be taken in particular during
maintenance and repair work.
Caution: In this area pay attention to the possible dangers of the laser beam.
Note or information on individual components of the device, which simplifies the
use or makes it more understandable.

BA 8016_2.0_EN(10/2016) 6 / 55
1.2 Designated Use
The Trotec Speedy 100 fiber is used for marking on metals and plastics. Many metals and
most plastics will show interaction with the laser beam. However, very clean metallic surfaces
which are highly polished and pure could show NO reaction. This is due to too high reflectivity
at 1064nm wavelength which is given especially for silver and copper. In general, the FP
model will react with more materials compared to the FC model.
The marking process must only be performed with a perfectly adjusted machine
(see also chapter 4 OPERATION).
Use of the system in other areas is against the designated use. The
manufacturer does not admit liability for damage to personal and/or equipment
resulting from such use.
The system must only be operated, maintained and repaired, by personnel that
are familiar with the designated field of use and the possible dangers of the
machine!
Non-observance of the instructions for operation, maintenance and repair
described in this Operation Manual excludes any liability of the manufacturer if
a defect occurs.
Caution when processing conductive materials (carbon fibers,…)! Conductive
dust or particles in the ambient air might damage electrical components and
lead to short circuits. Bear in mind that those defects are NOT warranted.
1.3 Disposal remarks
Do not dispose the machine with domestic waste!
Elektronic devices have to be disposed according to the regional directives
on electronic and electric waste disposal.
In case of further questions, please ask your supplier. He might take care of
proper disposal.

BA 8016_2.0_EN(10/2016) 7 / 55
1.4 Technical Data / System Specification
Mechanic
Working area
24 x 12 inch / 610 x 305 mm
Max. height of workpiece
4.9 inch / 125 mm with 3.2 inch lens
Max. engraving speed
78 inch/sec / 200 cm/sec
Motor
Brushless DC Servo motor
Encoder
Increment
Workpiece table
Solid metal (ferro-magnetic)
Max. load of workpiece
22 lbs / 10 kg
Lenses
3.2 inch
Features
Standard:
Electro-optic autofocus, Laser pointer (655nm, < 0,99mWcw),
Ferro-magnetic working table, 3.2 inch lens, USB connection, JobControl Expert software
Optional:
Honeycomb cutting table, Rotary attachment, Laserpower upgrade, Air assist including compressor,
Data import MAC, Trolley Table
Control system
Laserpower
Adjustable from 0 - 100%
Interface Hardware
RS-232-C: Data Rate 19.200 –155.200 Baud
USB: Data Rate 460.800 Baud
Interface Software
JobControl, HPGL
Laser Equipment
Laser tube
Pulsed fiberlaser, maintenance free
Laserpower: 10W, 20W, 30W
Wavelength
1064 nm
Cooling system
Air cooling unit
All systems air-cooled
Electricity, Power, Fuse
Voltage
Power consumption
Recommended fuse
Single phase 230V / 50Hz or 115V / 60 Hz
1200W
6,3A (230V), 10A (115V)
Dimensions
Width/depth/height (approx.)
38.3 x 30.1 x 18 inch / 974 x 765 x 457 mm
Weight (approx.)
220 lbs / 100 kg
Ambient conditions
Temperature
Humidity
59°F to 77°F / +15°C to +25°C
40% to max 70%, not condensing
Laser Safety
Laser class
CDRH Laser Safety
Laser Class 2
CE compliant, FDA approved
Interlock
Duplicate interlock safety system
SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
SEPTEMBER 2010

BA 8016_2.0_EN(10/2016) 8 / 55
1.5 Manufacturer's Label
The manufacturer's label is located on the back of the machine (see Figure below).
It is recommended to enter data such as serial number and year of manufacture into the
manufacturer's label below so that you always have this data at hand if necessary,

BA 8016_2.0_EN(10/2016) 9 / 55
1.6 EU –Declaration of conformity
The manufacturer
Trotec Laser GmbH.
Linzer Strasse 156,
A-4600 Wels, OÖ.,
AUSTRIA
hereby declares that the following product
Trotec 8016 Speedy 100 fiber
Model N° 8016 Speedy 100 fiber
has demonstrated conformity to the following guidelines:
2006/42/EG Directive for Machines
2006/95/EG Low Voltage Directive
2004/108/EG EMC Guideline
Applied during design and construction of this product:
- EN ISO12100 Machine Safety
- EN 60335-1/2007 Safety of Household and similar Appliances
- EN 55014-1/2006, EN 55014-2/1997 Electromagnetic Compatibility
- EN 60204-1 Machine Safety –electr. Equipment
- EN 60825-1/2007, EN 60825-4/2006 and EN 60825-14/2006
Safety of Laser Equipment
- EN 60950/2006 Safety of Electric Devices for Informatics including
electric Office Machines
- EN 55022/2008, EN 55024/2003 Electromagnetic Compatibility
Wels, Trotec Laser GmbH

BA 8016_2.0_EN(10/2016) 10 / 55
2 SAFETY
Please read this chapter before operating or servicing a Trotec Speedy 100 fiber laser
system!
2.1 General Safety Information
All personnel involved in installation, set-up, operation maintenance and repair of the machine, must
have read and understood the Operation Manual and in particular the "SAFETY" section. The user is
recommended to generate company-internal instructions considering the professional qualifications
of the personnel employed in each case, and the receipt of the instruction/Operation Manual or the
participation at introduction/training should be acknowledged in writing in each case.
Safety-conscious Working
The machine must only be operated by trained and authorized personnel.
The scopes of competence for the different activities in the scope of operating the machine must be
clearly defined and observed, so that under the aspect of safety no unclear questions of competence
occur. This applies in particular to activities on the electric equipment, which must only be performed
by special experts.
For all activities concerning installation, set-up, start-up, operation, modifications of conditions and
methods of operation, maintenance, inspection and repair, the switch-off procedures that may be
provided in the Operation Manual must be observed.

BA 8016_2.0_EN(10/2016) 11 / 55
Safety Information for the User and/or Operating Personnel
No work methods are permitted that affect the safety of the machine.
The operator must also ensure that no unauthorized persons work with the machine (e.g. by
activating equipment without authorization).
It is the duty of the operator, to check the machine before start of work for externally visible
damage and defects, and to immediately report changes that appear (including behavior
during operation) that affect the safety.
The user is responsible that the machine is only operated in perfect condition.
The user must guarantee the cleanness and accessibility at and around the machine by
corresponding instructions and controls.
Principally, no safety components may be removed or disabled (already here we emphasize
the imminent dangers, for example severe burns, loss of eye-sight). If the removal of safety
components is required during repair and service, the replacement of the safety components
must be performed immediately after completion of the service and repair activities.
Preparation, retooling, change of work piece, maintenance and repair activities must only
performed by trained personnel while the equipment is switched off.
It is forbidden to perform unauthorized modifications and changes to the machine. It is
emphasized, that any unauthorized modifications to the machine are not permitted for safety
reasons.

BA 8016_2.0_EN(10/2016) 12 / 55
2.2 Laser Safety Information
To assess the potential dangers laser systems pose, they are classified into 5 safety
classes: 1, 2, 3a, 3b and 4. Trotec Speedy 100 fiber is a machine of class 2 (USA:
Class II). This is guaranteed by the protective housing and the safety installations.
Please note that improper operation of the machine can override the status of safety
class 2 and can cause the emission of harmful laser radiation.
Class IIM laser products
Designation “M” indicates the use of magnification optics. The magnification collects
additional laser radiation into the eye. Designed for benefit of expanded beams. Class
2M is for visible wavelengths safe for momentary viewing (up to 0.25 seconds) without
optical aids and emission levels up to Class 3B AEL.
This laser marking system contains an YTTERBIUM FIBER LASER of class 4, that
emits intensive and invisible laser radiation. Without safety precautions the direct
radiation or even diffuse reflected radiation is dangerous!
Without safety precautions, the following risks exist with exposure to laser radiation:
Eyes: Burns to the retina for NIR (Near Infra Red) LASER lasers
Skin: Burns
Clothing: Danger of fire
Never try to modify or disassemble the laser and do not try to start up a system that
had been modified or disassembled!
Dangerous radiation exposure can result from the use of operation or
adjustment equipment other than that described here, and if different
operational methods are performed.
Service technicians are required to wear standard laser safety glasses for NIR (Near
Infra Red) LASER lasers (wavelength 1060 nm) whenever working on open laser
beam.

BA 8016_2.0_EN(10/2016) 13 / 55
Dangerous radiation exposure can result from the use of materials other than
described in Section 1.2 Designated Use:
In case of using highly reflecting materials like
blank or polished metals
metals with very high reflectivity like copper, brass, gold, silver
any materials with highly reflecting coatings
other highly reflecting materials,
especially in combination with high laser power, low processing speed and/or work pieces
with curved or inclined surfaces, laser radiation might be reflected towards the protection
cover. With a very low probability this protection cover could be damaged if the reflected
radiation is FOCUSSED onto the surface of the protection cover.
Therefore visual inspection for point-like defects on the protection cover should be done if
the aforementioned conditions are given.
The loss of yellow color on the protection cover indicates a damage of the protecting layer. If
you detect such effects, immediately turn off the laser machine and take care to get a new
protection cover.
Also other components inside the machine may be damaged if the aforementioned conditions are
given. To improve laser safety an optional “Laser Protection Cover” is available on request.

BA 8016_2.0_EN(10/2016) 14 / 55
2.3 Safety Precautions when Operating the Machine
In your Trotec Speedy 100 fiber, a closed safety system is integrated which immediately
switches off the power to the laser tube when the protection cover is opened. Consequently
an incomplete marking can occur if the cover is opened during operation. Therefore, first
press the "PAUSE" button, if you want to interrupt a marking process.
Please remember the following safety precautions when working with this machine:
A fire extinguisher must always be at hand as the laser beam can ignite flammable materials.
Do not store any flammable materials in the inside of the machine or in the immediate vicinity
of the machine.
Unsupervised operation of the system is not permitted.
Adjustment of the beam path must be performed only by especially trained personnel. An
improper setting can lead to uncontrolled emission of the laser radiation.
Before processing materials the user must verify, whether harmful materials can be
generated and whether the filter equipment of the exhaust system is suitable for the harmful
materials. We emphasize that it is the responsibility of the user, to consider the national and
regional threshold values for dust, fogs and gases when selecting the filters and the exhaust
system. (The values for the maximum workplace concentration must not be exceeded.)
Please refer to the manual of the exhaust system on how and in what intervals you need to
replace filters.
PVC (polyvinyl chloride) must under no circumstances be processed with the laser.
Should you have further questions before starting work, please contact your local Trotec
dealer or Trotec.

BA 8016_2.0_EN(10/2016) 15 / 55
2.4 Warning and Information Labels
The warning and information labels are attached in such positions of the
machine that could represent a source of danger during set-up and
operation. Therefore, follow the information on the labels. If labels are lost
or damaged, they must be replaced immediately.
1
6
2
7
3
8
4
9
5
10
4
5
6
7
1
5
4
5
7
1
6
1
8
6
2
3
9

BA 8016_2.0_EN(10/2016) 16 / 55
1
6
2
7
3
8
4
9
5
10
2
3
1
3
10
5
7
7
5
5

BA 8016_2.0_EN(10/2016) 17 / 55
3 BEFORE OPERATION
3.1 Unpacking
You receive your Trotec laser machine packed in a cardboard box or wooden box, which
contains the laser and additional accessories. The following steps give you an overview of
the unpacking and assembly of the laser. Please follow these steps carefully.
Keep the packing box. You will require it in case of a return.
Dispose all waste according to the applicable waste disposal law.
1. Remove the cover. Please do not forget to store this box in a dry place.
2. Carefully remove the foam material, which protects the viewing window of the cover.
3. Lift the laser marker out of the box. For this you will require two persons. Position the
laser marker on a stable table or the delivered stand (optional).
4. Remove the accessories box which contains all parts required for the installation of the
laser system.
5. Open the accessories box.

BA 8016_2.0_EN(10/2016) 18 / 55
3.2 Contents of Delivery
Transport and service packaging
Laser inclusive optics
Stand (optional)
Accessories box, containing:
1. CD Trotec software / printer driver incl. Operation Manual
2. Mains cable
3. Computer connection cable USB
4. Computer connection cable serial (optional)
5. Cleaning kit for optics
6. Allen key set 1.5 - 10 mm
7. Focus tool(s)
1
5
7
2
6
3
4

BA 8016_2.0_EN(10/2016) 19 / 55
3.3 Location
Before you install the laser system, you should select an appropriate location. Follow the
guidelines shown below:
Avoid locations where the system is exposed to high temperatures, dust and
high humidity. (The humidity must not exceed 70% and the temperature must
not be close to the dew point.)
Avoid locations, where the system is exposed to mechanical shocks.
Fuse protection:
Do not connect other machines via the laser fuse, as the laser marker system
requires the full amperage.
Avoid locations with poor air circulation.
Select a location, whose room temperature is between 15 C and 25 C (59° –
77° F) Avoid higher ambient temperatures and strong exposure of the marker
to the sun. Use blinds, if required.
Select a location close to ventilation (if available).
Select a location that is not more than 2.50 m away from your computer (max.
cable length to avoid disturbing interferences).
Try to place a working table or a place to put things next to it. This shall avoid,
that the machine is misused as a table.

BA 8016_2.0_EN(10/2016) 20 / 55
3.4 Exhaust System –Requirements
Do not start the machine without an adequate exhaust system.
3.5 Computer –Requirements
The following recommendation represents the minimum requirements.
When using a more powerful computer the graphics are generated and
displayed faster and the computing times and the data transfer to the laser are
reduced. To use the newest software version, you might have to abide other
requirements.
Windows 7® 32/64-bit or
Windows Vista® 32/64-bit (with Service Pack 1 or later) or
Windows® XP 32/64-bit (with Service Pack 2 or later)
512 MB of RAM, 400 MB of hard disk space
Pentium® 1 GHz processor or AMD Athlon™ XP
1024 x 768 or better monitor resolution
24-bit color depth graphics card
1 free USB interface
Serial port RS232 (optional)
CD drive
Mouse