TSYS PAX-S300 User manual

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 1
How to connect to TSYS PAX-S300 Card Processing Terminal
via Physical Ethernet LAN and its setup?
(TSYS, Model PAX-S300)
May-21-2020, Version V1.0
Contact information: [e-mail]
Index
Page#
PAX Card Processing Terminal Setup
2-7
Link with DolphinPOS APP
7-9
Enable Static IP to PAX Terminal
9-11

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 2
PAX Card Processing Terminal Setup

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 3
Step 1: Connect the Ethernet LAN cable into “red cord” as shown in below.
Step 2: Connect the Power Pin of the cable into the hole has shown in below and
other end of it goes into power supply. Which will turns ON the PAX device.

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 4
Note: Make sure both PAX terminal device and IPAD which you are using for POS APP
are on the same LAN network.
Step 3: On the PAX front Panel
a) Hold “F+1” keys together
b) default Password is today’s date mmddyyyy (example march 13th 2020 i.e
03132020)
c) Scroll down 1 page (press down arrow) and press to “2.Communication”
option.

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 5
d) Enter your password again (it’s today’s date mmddyyyy, if it is not changed)
e) Scroll down 2 pages (press down arrow two times) and press "1. LAN
Parameters".
f) press “2.IP Address” and Note down the IP Address (xxx.xxx.xxx.xxx)

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 6
g) press enter
h) press down arrow & go to “ping” option and press “green” enter button
If DNS resolve error appears (your internet may be down please
confirm)
If ping is ok, click red ‘x’ button, and press red ‘x’ button 3 times to go
to main screen

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 7
To verify the internet connectivity of PAX LAN setup, you can do same ping test from
DOS command prompt with below command on the PC (which should be on the
same local network)
C:\xxx>ping xxx.xxx.xxx.xxx –t (Where xxx.xxx.xxx.xxx is your PAX LAN IP address
which is assigned to it)
You can see below YouTube video link of DolphinPOS for the same
https://www.youtube.com/watch?v=h2XMsfBnEoU
DolphinPOS APP Setup to communicate with PAX S300
1) Click on dolphin pos App (restaurant/retail) on IPAD and go to Home screen
2) Go to “More”“Card” and press “Integrated PinPad”
3) Change “IP Address”in APP with some minor changes listed below (which we
have noted from above PAX S300 Hardware Setup).
Example in PAX s300 if it is 192.168.000.055 , then in IPAD APP it
should be 192.168.0.55

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 8
Example in PAX S300 if IP address is 192.168.001.155 , then in IPAD APP
it should be 192.168.1.155
4) Port No.: 10009
5) Then Tap on “Configure Pin Pad”

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 9
6) Go to “General” and Select card provider to “TSYS” from the dropdown
7) In the same page “Enable Capture Signature” flag if you want to capture
signature on the TSYS display.

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 10
8) That’s it, just close the application and open it. You are good to go!
How to make IP address to Static
1. Press Menu or "FUNC" and "1" at the same time
2. Enter your password (default password is the current date in MMDDYYYY format)
3. Scroll down 1 page and press "2. Communication"
4. Enter your password again
5. Scroll down 2 pages and press "1. LAN Parameters"
6. Press "1. LAN Type"
7. Press "2. Static"

TSYS LAN based Card Processing Terminal Setup with DolphinPOS
DolphinPOS User Guide Page 11
8. Go back into “LAN Type”and verify that LAN Type:”2” is selected before proceeding.
9. Go back to the home screen by using the back button on the screen several times.
You will need to power cycle (unplug and replug the power cable) the device for it to
receive a new IP address from the router.