Turbosound NuQ-AN Series User manual

NuQ-AN Series
NuQ82-AN (WH), NuQ102-AN (WH), NuQ122-AN (WH),
NuQ152-AN (WH), NuQ115B-AN (WH), NuQ118B-AN (WH)
600 and 2,500 Watt 2 Way Full Range Powered Loudspeakers
3000 Watt Powered Subwoofers
KLARK TEKNIK DSP Technology and ULTRANET Networking

2NuQ-AN Series Quick Start Guide 3
Terminals marked with this symbol carry
electrical current of sucient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼"TS or twist-locking plugs pre-installed. Allother
installation or modication should be performed only
by qualiedpersonnel.
This symbol, wherever it appears,
alertsyou to the presence of uninsulated
dangerous voltage inside the
enclosure-voltage that may be sucient to constitute a
risk ofshock.
This symbol, wherever it appears,
alertsyou to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, donot
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualied personnel.
Caution
To reduce the risk of re or electric shock,
do not expose this appliance to rain and
moisture.The apparatus shall not be exposed to dripping
or splashing liquids and no objects lled with liquids,
suchas vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by qualied service personnel only.
Toreduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualied
servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong.The wide
blade or the third prong are provided for your safety. Ifthe
provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories specied by
themanufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table specied by the
manufacturer, orsold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
beendropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
17. Correct disposal of this
product:This symbol indicates that
this product must not be disposed
of with household waste,
according to the WEEE Directive
(2012/19/EU) and your national
law.This product should be taken
to a collection center licensed for the recycling of waste
electrical and electronic equipment (EEE).The
mishandling of this type of waste could have a possible
negative impact on the environment and human health
due to potentially hazardous substances that are generally
associated with EEE. At the same time, your cooperation
in the correct disposal of this product will contribute to
the ecient use of natural resources. For more
information about where you can take your waste
equipment for recycling, please contact your local city
oce, or your household waste collection service.
18. Do not install in a conned space, such as a book
case or similar unit.
19. Do not place naked ame sources, such as lighted
candles, on the apparatus.
20. Please keep the environmental aspects of battery
disposal in mind. Batteries must be disposed-of at a
battery collection point.
21. Use this apparatus in tropical and/or
moderate climates.
MUSIC Group accepts no liability for any loss which
may be suered by any person who relies either
wholly or in part upon any description, photograph,
or statement contained herein.Technical specications,
appearances and other information are subject to
change without notice. All trademarks are the property
of their respective owners. MIDAS, KLARK TEKNIK,
LAB GRUPPEN, LAKE,TANNOY, TURBOSOUND,
TC ELECTRONIC,TC HELICON, BEHRINGER, BUGERA,
COOLAUDIO and EUROCOM are trademarks or
registered trademarks of MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2017 All rights reserved.
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
LimitedWarranty, please see complete details online at
music-group.com/warranty.
Las terminales marcadas con este símbolo
transportan corriente eléctrica de
magnitud suciente como para constituir
un riesgo de descarga eléctrica. Utilice solo cables de
altavoz profesionales y de alta calidad con conectores
TS de 6,3 mm o de bayoneta prejados. Cualquier otra
instalación o modicación debe ser realizada únicamente
por un técnico cualicado.
Este símbolo, siempre que aparece,
leadvierte de la presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser suciente para constituir un riesgo
dedescarga.
Este símbolo, siempre que aparece,
leadvierte sobre instrucciones operativas
y de mantenimiento que aparecen en la
documentación adjunta. Por favor, lea el manual.
Atención
Para reducir el riesgo de descarga
eléctrica, no quite la tapa (o la parte
posterior). No hay piezas en el interior del equipo que
puedan ser reparadas por el usuario. Si es necesario,
póngase en contacto con personal cualicado.
Atención
Para reducir el riesgo de incendio o
descarga eléctrica, no exponga este
aparato a la lluvia, humedad o alguna otra fuente que
pueda salpicar o derramar algún líquido sobre el aparato.
Nocoloque ningún tipo de recipiente para líquidos sobre
el aparato.
Atención
Las instrucciones de servicio deben
llevarlas a cabo exclusivamente personal
cualicado. Para evitar el riesgo de una descarga eléctrica,
no realice reparaciones que no se encuentren descritas
en el manual de operaciones. Lasreparaciones deben ser
realizadas exclusivamente por personalcualicado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas las advertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un paño seco.
7. No bloquee las aberturas de ventilación. Instale el
equipo de acuerdo con las instrucciones del fabricante.
8. No instale este equipo cerca de fuentes de calor
tales como radiadores, acumuladores de calor, estufas u
otros aparatos (incluyendo amplicadores) que puedan
producir calor.
9. No elimine o deshabilite nunca la conexión a tierra
del aparato o del cable de alimentación de corriente.
Unenchufe polarizado tiene dos polos, uno de los cuales
tiene un contacto más ancho que el otro. Una clavija con
puesta a tierra dispone de tres contactos: dos polos y la
puesta a tierra. El contacto ancho y el tercer contacto,
respectivamente, son los que garantizan una mayor
seguridad. Si el enchufe suministrado con el equipo no
concuerda con la toma de corriente, consulte con un
electricista para cambiar la toma de corriente obsoleta.
10. Coloque el cable de suministro de energía de manera
que no pueda ser pisado y que esté protegido de objetos
alados. Asegúrese de que el cable de suministro de
energía esté protegido, especialmente en la zona de la
clavija y en el punto donde sale del aparato.
11. Use únicamente los dispositivos o accesorios
especicados por el fabricante.
12. Use únicamente la
carretilla, plataforma,
trípode, soporte o mesa
especicados por el
fabricante o suministrados
junto con el equipo.
Altransportar el equipo,
tenga cuidado para evitar
daños y caídas al tropezar con algún obstáculo.
13. Desenchufe el equipo durante tormentas o si no va a
utilizarlo durante un periodo largo.
14. Confíe las reparaciones únicamente a servicios
técnicos cualicados. La unidad requiere mantenimiento
siempre que haya sufrido algún daño, si el cable de
suministro de energía o el enchufe presentaran daños,
sehubiera derramado un líquido o hubieran caído objetos
dentro del equipo, si el aparato hubiera estado expuesto
a la humedad o la lluvia, si ha dejado de funcionar de
manera normal o si ha sufrido algún golpe o caída.
15. Al conectar la unidad a la toma de corriente eléctrica
asegúrese de que la conexión disponga de una unión
atierra.
16. Si el enchufe o conector de red sirve como único
medio de desconexión, éste debe ser accesiblefácilmente.
17. Cómo debe deshacerse de
este aparato: Este símbolo indica
que este aparato no debe ser
tratado como basura orgánica,
según lo indicado en la Directiva
WEEE (2012/19/EU) y a las
normativas aplicables en su país.
En lugar de ello deberá llevarlo al punto limpio más
cercano para el reciclaje de sus elementos eléctricos/
electrónicos (EEE). Al hacer esto estará ayudando a
prevenir las posibles consecuencias negativas para el
medio ambiente y la salud que podrían ser provocadas por
una gestión inadecuada de este tipo de aparatos. Además,
el reciclaje de materiales ayudará a conservar los recursos
naturales. Para más información acerca del reciclaje de
este aparato, póngase en contacto con el Ayuntamiento
de su ciudad o con el punto limpio local.
18. No instale esta unidad en un espacio muy reducido,
tal como encastrada en una librería o similar.
19. No coloque objetos con llama, como una vela
encendida, sobre este aparato.
20. Tenga presentes todas las advertencias relativas
al reciclaje y correcta eliminación de las pilas. Las pilas
deben ser siempre eliminadas en un punto limpio y nunca
con el resto de la basura orgánica.
21. Use este aparato en rangos de temperatura
moderados y/o tropicales.
MUSIC Group no admite ningún tipo de responsabilidad
por cualquier daño o pérdida que pudiera sufrir
cualquier persona por conar total o parcialmente
en la descripciones, fotografías o armaciones
contenidas en este documento. Las especicaciones
técnicas, imágenes y otras informaciones contenidas
en este documento están sujetas a modicaciones
sin previo aviso. Todas las marcas comerciales que
aparecen aquí son propiedad de sus respectivos
dueños. MIDAS, KLARK TEKNIK, LAB GRUPPEN,
LAKE,TANNOY, TURBOSOUND,TC ELECTRONIC,
TC HELICON, BEHRINGER, BUGERA, COOLAUDIO y
EUROCOM son marcas comerciales o marcas registradas
de MUSIC Group IP Ltd. © MUSIC Group IP Ltd.
2017 Reservados todos los derechos.
Si quiere conocer los detalles y condiciones aplicables
de la garantía así como información adicional sobre la
Garantía limitada de MUSIC Group, consulte online toda la
información en la web music-group.com/warranty.
Important Safety
Instructions
LEGAL DISCLAIMER
Instrucciones de
seguridad
NEGACIÓN LEGAL
GARANTÍA LIMITADA
LIMITED WARRANTY

4NuQ-AN Series Quick Start Guide 5
Les points repérés par ce symbole portent
une tension électrique susante pour
constituer un risque d’électrocution.
Utilisez uniquement des câbles d’enceintes professionnels
de haute qualité avec ches Jack mono 6,35 mm ou ches
à verrouillages déjà installées.Touteautre installation ou
modication doit être eectuée uniquement par un
personnel qualié.
Ce symbole avertit de la présence d’une
tension dangereuse et non isolée à
l’intérieur de l’appareil - elle peut
provoquer des chocs électriques.
Attention
Ce symbol signale les consignes
d’utilisation et d’entre !Tien importantes
dans la documentation fournie. Lisez les consignes de
sécurité du manuel d’utilisation de l’appareil.
Attention
Pour éviter tout risque de choc électrique,
ne pas ouvrir le capot de l’appareil ni
démonter le panneau arrière. L’intérieur de l’appareil
ne possède aucun élément réparable par l’utilisateur.
Laissertoute réparation à un professionnel qualié.
Attention
Pour réduire les risques de feu et de choc
électrique, n’exposez pas cet appareil à la
pluie, à la moisissure, aux gouttes ou aux éclaboussures.
Ne posez pas de récipient contenant un liquide sur
l’appareil (un vase par exemple).
Attention
Ces consignes de sécurité et d’entretien
sont destinées à un personnel qualié.
Pouréviter tout risque de choc électrique, n’eectuez
aucune réparation sur l’appareil qui ne soit décrite par le
manuel d’utilisation. Les éventuelles réparations doivent
être eectuées uniquement par un technicien spécialisé.
1. Lisez ces consignes.
2. Conservez ces consignes.
3. Respectez tous les avertissements.
4. Respectez toutes les consignes d’utilisation.
5. N’utilisez jamais l’appareil à proximité d’un liquide.
6. Nettoyez l’appareil avec un chion sec.
7. Veillez à ne pas empêcher la bonne ventilation de
l’appareil via ses ouïes de ventilation. Respectezles
consignes du fabricant concernant l’installation
del’appareil.
8. Ne placez pas l’appareil à proximité d’une source
de chaleur telle qu’un chauage, une cuisinière ou tout
appareil dégageant de la chaleur (y compris un ampli
depuissance).
9. Ne supprimez jamais la sécurité des prises bipolaires
ou des prises terre. Les prises bipolaires possèdent deux
contacts de largeur diérente. Leplus large est le contact
de sécurité. Les prises terre possèdent deux contacts plus
une mise à la terre servant de sécurité. Si la prise du bloc
d’alimentation ou du cordon d’ali-mentation fourni ne
correspond pas à celles de votre installation électrique,
faites appel à un électricien pour eectuer le changement
de prise.
10. Installez le cordon d’alimentation de telle façon
que personne ne puisse marcher dessus et qu’il soit
protégé d’arêtes coupantes. Assurez-vous que le cordon
d’alimentation est sufsamment protégé, notamment au
niveau de sa prise électrique et de l’endroit où il est relié à
l’appareil; cela est également valable pour une éventuelle
rallonge électrique.
11. Utilisez exclusivement des accessoires et des
appareils supplémentaires recommandés par lefabricant.
12. Utilisez
exclusivement des
chariots, des diables,
desprésentoirs, despieds
et des surfaces de
travail recommandés
par le fabricant ou
livrés avec le produit.
Déplacezprécautionneusement tout chariot ou diable
chargé pour éviter d’éventuelles blessures en cas dechute.
13. Débranchez l’appareil de la tension secteur en cas
d’orage ou si l’appareil reste inutilisé pendant une longue
période de temps.
14. Les travaux d’entretien de l’appareil doivent
être eectués uniquement par du personnel qualié.
Aucunentretien n’est nécessaire sauf si l’appareil est
endommagé de quelque façon que ce soit (dommagessur
le cordon d’alimentation ou la prise par exemple), siun
liquide ou un objet a pénétré à l’intérieur du châssis,
si l’appareil a été exposé à la pluie ou à l’humidité, s’il ne
fonctionne pas correctement ou à la suite d’une chute.
15. L’appareil doit être connecté à une prise secteur
dotée d’une protection par mise à la terre.
16. La prise électrique ou la prise IEC de tout appareil
dénué de bouton marche/arrêt doit rester accessible
enpermanence.
17. Mise au rebut appropriée de
ce produit: Ce symbole indique
qu’en accord avec la directive DEEE
(2012/19/EU) et les lois en vigueur
dans votre pays, ce produit ne doit
pas être jeté avec les déchets
ménagers. Ce produit doit être
déposé dans un point de collecte agréé pour le recyclage
des déchets d’équipements électriques et électroniques
(EEE). Une mauvaise manipulation de ce type de déchets
pourrait avoir un impact négatif sur l’environnement et la
santé à cause des substances potentiellement
dangereuses généralement associées à ces équipements.
En même temps, votre coopération dans la mise au rebut
de ce produit contribuera à l’utilisation ecace des
ressources naturelles. Pour plus d’informations sur
l’endroit où vous pouvez déposer vos déchets
d’équipements pour le recyclage, veuillez contacter votre
mairie ou votre centre local de collecte des déchets.
18. N’installez pas l’appareil dans un espace conné tel
qu’une bibliothèque ou meuble similaire.
19. Ne placez jamais d’objets enammés, tels que des
bougies allumées, sur l’appareil.
20. Gardez à l’esprit l’impact environnemental lorsque
vous mettez des piles au rebus. Les piles usées doivent
être déposées dans un point de collecte adapté.
21. Utilisez l’appareil dans un climat tropical
et/ou modéré.
MUSIC Group ne peut être tenu pour responsable pour
toute perte pouvant être subie par toute personne
se ant en partie ou en totalité à toute description,
photographie ou armation contenue dans ce
document. Les caractéristiques, l’apparence et d’autres
informations peuvent faire l’objet de modications
sans notication.Toutes les marques appartiennent à
leurs propriétaires respectifs. MIDAS, KLARK TEKNIK,
LAB GRUPPEN, LAKE,TANNOY, TURBOSOUND,
TC ELECTRONIC,TC HELICON, BEHRINGER, BUGERA,
COOLAUDIO et EUROCOM sont des marques ou marques
déposées de MUSIC Group IP Ltd. © MUSIC Group IP Ltd.
2017Tous droits réservés.
Pour connaître les termes et conditions de garantie
applicables, ainsi que les informations supplémentaires
et détaillées sur la Garantie Limitée de MUSIC Group,
consultez le site Internet music-group.com/warranty.
Vorsicht
Die mit dem Symbol markierten
Anschlüsse führen so viel Spannung,
dassdie Gefahr eines Stromschlags besteht.
Verwenden Sie nur hochwertige, professionelle
Lautsprecherkabel mit vorinstallierten 6,35 mm
MONO-Klinkensteckern oder Lautsprecherstecker
mit Drehverriegelung. Alle anderen Installationen
oder Modikationen sollten nur von qualiziertem
Fachpersonal ausgeführt werden.
Achtung
Um eine Gefährdung durch Stromschlag
auszuschließen, darf die Geräteabdeckung
bzw. Geräterückwand nicht abgenommen werden.
ImInnern des Geräts benden sich keine vom Benutzer
reparierbaren Teile. Reparaturarbeiten dürfen nur von
qualiziertem Personal ausgeführt werden.
Achtung
Um eine Gefährdung durch Feuer bzw.
Stromschlag auszuschließen, darf dieses
Gerät weder Regen oder Feuchtigkeit ausgesetzt werden
noch sollten Spritzwasser oder tropfende Flüssigkeiten
in das Gerät gelangen können. Stellen Sie keine mit
Flüssigkeit gefüllten Gegenstände, wie z. B.Vasen,
aufdasGerät.
Achtung
Die Service-Hinweise sind nur durch
qualiziertes Personal zu befolgen.
Umeine Gefährdung durch Stromschlag zu vermeiden,
führen Sie bitte keinerlei Reparaturen an dem Gerät
durch, die nicht in der Bedienungsanleitung beschrieben
sind. Reparaturen sind nur von qualiziertem
Fachpersonaldurchzuführen.
1. Lesen Sie diese Hinweise.
2. Bewahren Sie diese Hinweise auf.
3. Beachten Sie alleWarnhinweise.
4. Befolgen Sie alle Bedienungshinweise.
5. Betreiben Sie das Gerät nicht in der Nähe vonWasser.
6. Reinigen Sie das Gerät mit einem trockenenTuch.
7. Blockieren Sie nicht die Belüftungsschlitze. Beachten
Sie beim Einbau des Gerätes die Herstellerhinweise.
8. Stellen Sie das Gerät nicht in der Nähe von
Wärmequellen auf. SolcheWärmequellen sind z. B.
Heizkörper, Herde oder andereWärme erzeugende Geräte
(auchVerstärker).
9. Entfernen Sie in keinem Fall die
Sicherheitsvorrichtung von Zweipol- oder geerdeten
Steckern. Ein Zweipolstecker hat zwei unterschiedlich
breite Steckkontakte. Ein geerdeter Stecker hat zwei
Steckkontakte und einen dritten Erdungskontakt.
Derbreitere Steckkontakt oder der zusätzliche
Erdungskontakt dient Ihrer Sicherheit. Falls das
mitgelieferte Steckerformat nicht zu Ihrer Steckdose
passt, wenden Sie sich bitte an einen Elektriker, damit die
Steckdose entsprechend ausgetauscht wird.
10. Verlegen Sie das Netzkabel so, dass es vor
Tritten und scharfen Kanten geschützt ist und nicht
beschädigt werden kann. Achten Sie bitte insbesondere
im Bereich der Stecker, Verlängerungskabel und an
der Stelle, an der das Netzkabel das Gerät verlässt,
aufausreichendenSchutz.
11. Das Gerät muss jederzeit mit intaktem Schutzleiter
an das Stromnetz angeschlossen sein.
12. Sollte der Hauptnetzstecker oder eine
Gerätesteckdose die Funktionseinheit zum Abschalten
sein, muss diese immer zugänglich sein.
13. Verwenden Sie nur Zusatzgeräte/Zubehörteile,
dielaut Hersteller geeignet sind.
14. Verwenden
Sie nurWagen,
Standvorrichtungen,
Stative, Halter oder Tische,
die vom Hersteller benannt
oder im Lieferumfang
des Geräts enthalten
sind. Falls Sie einen
Wagen benutzen, seien Sie vorsichtig beim Bewegen
derWagen-Gerätkombination, umVerletzungen durch
Stolpern zuvermeiden.
15. Ziehen Sie den Netzstecker bei Gewitter oder wenn
Sie das Gerät längere Zeit nicht benutzen.
16. Lassen Sie alleWartungsarbeiten nur von
qualiziertem Service-Personal ausführen. EineWartung
ist notwendig, wenn das Gerät in irgendeinerWeise
beschädigt wurde (z. B. Beschädigung des Netzkabels oder
Steckers), Gegenstände oder Flüssigkeit in das Geräteinnere
gelangt sind, das Gerät Regen oder Feuchtigkeit ausgesetzt
wurde, das Gerät nicht ordnungsgemäß funktioniert oder
auf den Boden gefallen ist.
17. Korrekte Entsorgung dieses
Produkts: Dieses Symbol weist
darauf hin, das Produkt
entsprechend derWEEE Direktive
(2012/19/EU) und der jeweiligen
nationalen Gesetze nicht
zusammen mit Ihren
Haushaltsabfällen zu entsorgen. DiesesProdukt sollte bei
einer autorisierten Sammelstelle für Recycling elektrischer
und elektronischer Geräte (EEE) abgegeben werden.
Wegen bedenklicher Substanzen, diegenerell mit
elektrischen und elektronischen Geräten in Verbindung
stehen, könnte eine unsachgemäße Behandlung dieser
Abfallart eine negative Auswirkung auf Umwelt und
Gesundheit haben. Gleichzeitig gewährleistet Ihr Beitrag
zur richtigen Entsorgung dieses Produkts die eektive
Nutzung natürlicher Ressourcen. Fürweitere
Informationen zur Entsorgung Ihrer Geräte bei einer
Recycling-Stelle nehmen Sie bitte Kontakt zum
zuständigen städtischen Büro, Entsorgungsamt oder zu
Ihrem Haushaltsabfallentsorgerauf.
18. Installieren Sie das Gerät nicht in einer beengten
Umgebung, zum Beispiel Bücherregal oder ähnliches.
19. Stellen Sie keine Gegenstände mit oenen
Flammen, etwa brennende Kerzen, auf das Gerät.
20. Beachten Sie bei der Entsorgung von Batterien
den Umweltschutz-Aspekt. Batterien müssen bei einer
Batterie-Sammelstelle entsorgt werden.
21. Verwenden Sie das Gerät in tropischen und/oder
gemäßigten Klimazonen.
MUSIC Group übernimmt keine Haftung für Verluste,
die Personen entstanden sind, die sich ganz oder
teilweise auf hier enthaltene Beschreibungen,
Fotos oder Aussagen verlassen haben.Technische Daten,
Erscheinungsbild und andere Informationen können
ohne vorherige Ankündigung geändert werden.
AlleWarenzeichen sind Eigentum der jeweiligen
Inhaber. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE,
TANNOY,TURBOSOUND,TC ELECTRONIC,TC HELICON,
BEHRINGER, BUGERA, COOLAUDIO und EUROCOM
sindWarenzeichen oder eingetrageneWarenzeichen
der MUSIC Group IP Ltd. © MUSIC Group IP Ltd.
2017 Alle Rechte vorbehalten.
Die geltenden Garantiebedingungen und zusätzliche
Informationen bezüglich der von MUSIC Group
gewährten beschränkten Garantie nden Sie online unter
music-group.com/warranty.
Consignes de sécurité
DÉNI LÉGAL
GARANTIE LIMITÉE
Wichtige
Sicherheitshinweise
HAFTUNGSAUSSCHLUSS
BESCHRÄNKTE GARANTIE

6NuQ-AN Series Quick Start Guide 7
Aviso!
Terminais marcados com o símbolo
carregam corrente elétrica de magnitude
suciente para constituir um risco de choque elétrico.
Use apenas cabos de alto-falantes de alta qualidade
com pluguesTS de ¼" ou plugues com trava de torção
pré-instalados.Todas as outras instalações e modicações
devem ser efetuadas por pessoasqualicadas.
Este símbolo, onde quer que o encontre,
alerta-o para a leitura das instruções de
manuseamento que acompanham o
equipamento. Por favor leia o manual de instruções.
Atenção
De forma a diminuir o risco de choque
eléctrico, não remover a cobertura
(ouasecção de trás). Não existem peças substituíveis por
parte do utilizador no seu interior. Para esse efeito recorrer
a um técnico qualicado.
Atenção
Para reduzir o risco de incêndios ou
choques eléctricos o aparelho não deve ser
exposto à chuva nem à humidade. Além disso, não deve
ser sujeito a salpicos, nem devem ser colocados em cima
do aparelho objectos contendo líquidos, tais como jarras.
Atenção
Estas instruções de operação devem ser
utilizadas, em exclusivo, por técnicos de
assistência qualicados. Para evitar choques eléctricos
não proceda a reparações ou intervenções, que não as
indicadas nas instruções de operação, salvo se possuir as
quali-cações necessárias. Para evitar choques eléctricos
não proceda a reparações ou intervenções, que não as
indicadas nas instruções de operação. Só o deverá fazer se
possuir as qualicações necessárias.
1. Leia estas instruções.
2. Guarde estas instruções.
3. Preste atenção a todos os avisos.
4. Siga todas as instruções.
5. Não utilize este dispositivo perto de água.
6. Limpe apenas com um pano seco.
7. Não obstrua as entradas de ventilação. Instale de
acordo com as instruções do fabricante.
8. Não instale perto de quaisquer fontes de calor
tais como radiadores, bocas de ar quente, fogões de
sala ou outros aparelhos (incluindo amplicadores)
que produzam calor.
9. Não anule o objectivo de segurança das chas
polarizadas ou do tipo de ligação à terra. Uma cha
polarizada dispõe de duas palhetas sendo uma mais larga
do que a outra. Uma cha do tipo ligação à terra dispõe
de duas palhetas e um terceiro dente de ligação à terra.
A palheta larga ou o terceiro dente são fornecidos para
sua segurança. Se a cha fornecida não encaixar na sua
tomada, consulte um electricista para a substituição da
tomada obsoleta.
10. Proteja o cabo de alimentação de pisadelas ou
apertos, especialmente nas chas, extensões, e no local
de saída da unidade. Certique-se de que o cabo eléctrico
está protegido. Verique particularmente nas chas, nos
receptáculos e no ponto em que o cabo sai doaparelho.
11. O aparelho tem de estar sempre conectado à rede
eléctrica com o condutor de protecção intacto.
12. Se utilizar uma cha de rede principal ou uma
tomada de aparelhos para desligar a unidade de
funcionamento, esta deve estar sempre acessível.
13. Utilize apenas ligações/acessórios especicados
pelofabricante.
14. Utilize apenas com
o carrinho, estrutura,
tripé, suporte, ou mesa
especicados pelo
fabricante ou vendidos
com o dispositivo.
Quandoutilizar um
carrinho, tenha cuidado ao
mover o conjunto carrinho/dispositivo para evitar danos
provocados pela terpidação.
15. Desligue este dispositivo durante as trovoadas
ou quando não for utilizado durante longos períodos
detempo.
16. Qualquer tipo de reparação deve ser sempre
efectuado por pessoal qualicado. É necessária uma
reparação sempre que a unidade tiver sido de alguma
forma danicada, como por exemplo: no caso do cabo
de alimentação ou cha se encontrarem danicados;
naeventualidade de líquido ter sido derramado ou
objectos terem caído para dentro do dispositivo; no caso
da unidade ter estado exposta à chuva ou à humidade;
seesta não funcionar normalmente, ou se tiver caído.
17. Correcta eliminação deste
produto: este símbolo indica que
o produto não deve ser eliminado
juntamente com os resíduos
domésticos, segundo a Directiva
REEE (2012/19/EU) e a legislação
nacional. Este produto deverá
ser levado para um centro de recolha licenciado para a
reciclagem de resíduos de equipamentos eléctricos e
electrónicos (EEE). O tratamento incorrecto deste tipo
de resíduos pode ter um eventual impacto negativo
no ambiente e na saúde humana devido a substâncias
potencialmente perigosas que estão geralmente
associadas aos EEE. Ao mesmo tempo, a sua colaboração
para a eliminação correcta deste produto irá contribuir
para a utilização eciente dos recursos naturais. Paramais
informação acerca dos locais onde poderá deixar o seu
equipamento usado para reciclagem, é favor contactar
os serviços municipais locais, a entidade de gestão de
resíduos ou os serviços de recolha de resíduosdomésticos.
18. Não instale em lugares connados, tais como
estantes ou unidades similares.
19. Não coloque fontes de chama, tais como velas
acesas, sobre o aparelho.
20. Favor, obedecer os aspectos ambientais de descarte
de bateria. Baterias devem ser descartadas em um ponto
de coletas de baterias.
21. Use este aparelho em climas tropicais
e/ou moderados.
O MUSIC Group não se responsabiliza por perda alguma
que possa ser sofrida por qualquer pessoa que dependa,
seja de maneira completa ou parcial, de qualquer
descrição, fotograa, ou declaração aqui contidas.
Dados técnicos, aparências e outras informações
estão sujeitas a modicações sem aviso prévio.
Todas as marcas são propriedade de seus respectivos
donos. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE,
TANNOY,TURBOSOUND,TC ELECTRONIC,TC HELICON,
BEHRINGER, BUGERA, COOLAUDIO e EUROCOM são
marcas ou marcas registradas do MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2017Todos direitos reservados.
Para obter os termos de garantia aplicáveis e condições e
informações adicionais a respeito da garantia limitada do
MUSIC Group, favor vericar detalhes na íntegra através
do website music-group.com/warranty.
注意
感電の.恐れがありますので、カ
バーやその他の部品を取り外
したり、開けたりしないでください。高品
質なプロ用スピーカーケーブル（¼" TS標準
ケーブルおよびツイストロッキングプラ
グケーブル）を使用してください。
注意
火事および感電の危険を防ぐ
ため、本装置を水分や湿気の
あるところには設置しないで下さい。装置
には決して水分がかからないように注意
し、花瓶など水分を含んだものは、装置の
上には置かないようにしてください。
注意
このマークが表示されている
箇所には、内部に高圧電流が
生じています。手を触れると感電の恐れが
あります。
注意
取り扱いとお手入れの方法に
ついての重要な説明が付属の
取扱説明書に記載されています。ご使用の
前に良くお読みください。
注意
1. 取扱説明書を通してご覧ください。
2. 取扱説明書を大切に保管してくだ
さい。
3. 警告に従ってください。
4. 指示に従ってください。
5. 本機を水の近くで使用しないでくだ
さい。
6. お手入れの際は常に乾燥した布巾を使
ってください 。
7. 本機は、取扱説明書の指示に従い、
適切な換気を妨げない場所に設置してく
ださい。取扱説明書に従って設置してくだ
さい。
8. 本機は、電気ヒーターや温風機器、
ストーブ、調理台やアンプといった熱源か
ら離して 設 置してください 。
9. ニ極式プラグおよびアースタイプ
(三芯)プラグの安全ピンは取り外さないで
ください。ニ極式プラグにはピンが二本つ
いており、そのうち一本はもう一方よりも幅
が広くなっています。アースタイプの三芯プ
ラグにはニ本のピンに加えてアース用のピ
ンが一本ついています。これらの幅の広い
ピン、およびアースピンは、安全のためのも
のです。備え付けのプラグが、お使いのコン
セントの形状と異なる場合は、電器技師に
相談してコンセントの交換をして下さい。
10. 電源コードを踏みつけたり、挟んだり
しないようご注意ください。電源コードや
プラグ、コンセント及び製品との接続には
十分にご注意ください。
11. すべての装置の接地(アース)が確保
されていることを確認して下さい。
12. 電源タップや
電源プラグは電
源遮断機として利
用されている場合
には、これが直ぐ
に操作できるよう
手元に設置して下
さい。
13. 付属品は本機製造元が指定したもの
のみをお使いください。
14. カートスタンド、三脚、ブラケット、
テーブルなどは、本機製造元が指定したも
の、もしくは本 機 の付属 品となるものの み
をお使いください。カートを使用しての運
搬の際は、器具の落下による怪我に十分ご
注意ください。
15. 雷雨の場合、もしくは長 期 間ご 使 用に
ならない場合は、電源プラグをコンセント
から抜いてください。
16. 故障の際は当社指定のサービス技術
者にお問い合わせください。電源コードも
しくはプラグの損 傷 、液体の装置内への浸
入、装置の上に物が落下した場合、雨や湿
気に装置が晒されてしまった場合、正常に
作動しない場合、もしくは装置を地 面に落
下させてしまった場合など、いかなる形で
あれ装置に損傷が加わった場合は、装置
の修理・点検を受けてください。
17. 本製品に電源コード
が付属されている場合、
付属の電源コードは本製
品以外ではご使用いただ
けません。電源コードは
必ず本製品に付属された
電源コードのみご使用く
ださい。
18. ブックケースなどのような、閉じたス
ペースには設置しないでください。
19. 本機の上に点火した蝋燭などの裸火
を置かないでください。
20. 電池廃棄の際には、環境へのご配慮
をお願いします。電池は、かならず電池回
収場所に廃棄してください。
21. 本機器は熱帯気候および/または温
帯気候下でご使用ください。
ここに含まれる記述、写真、意見の全
体または一部に依拠して、いかなる人が
損害を生じさせた場合にも、MUSIC Group
は一切の賠償責任を負いません。技術
仕様、外観およびその他の情報は予告
なく変 更になる場合があります。商標
はすべて、それぞれの所有者に帰属しま
す。MIDAS、KLARK TEKNIK、LAB GRUPPEN、
LAKE、TANNOY、TURBOSOUND、TC ELECTRONIC、
TC HELICON、BEHRINGER、BUGERA、COOLAUDIO
およびEUROCOMはMUSIC Group IP Ltd.
の商標または登録商標です。© MUSIC Group
IP Ltd. 2017無断転用禁止。
適用される保証条件とMUSIC Groupの限定
保証に関する概要については、オンライン
上music-group.com/warrantyにて詳細をご確
認ください。
Instruções de Segurança
Importantes
LEGAL RENUNCIANTE
GARANTIA LIMITADA
安全にお使いいただくために
限定保証
法的放棄

8NuQ-AN Series Quick Start Guide 9
Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further information about this or any other TURBOSOUND product,
please visit our website at turbosound.com.
Unpacking the Loudspeaker
After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim.
Please retain all packaging in case of futurere-shipment.
Controls
(6)
(7)
(9)
(10)
(11)
(13)
(8)
(1)
(2)
(3)
(4)
(5)
(12)
ࣝధ൦ಗ঄ᄋጽቬ᝻ܭЧధ
ܹᄋႄุߜڛᝐႄԁᬘǎᬎ
Ώၺࣝధ ¼'' TSᩛତ݁
ᄋᰵַ᠐˅ˋܧ٩ጴǎధᄋ߸ᜊួ
஠ڪᮍႁՍಬᄋ˅ˋցᤊᛢǎ
൦ಗ঄ଣᧉ১ַаߜڛఴ
ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ
൦ಗ঄ଣᧉ১ಋ󰪀ᬅᄋ᧙᜷
ᄋΏၺԤ፦οឮ௛ǎឱ󰪀឵ధ
Угǎ
࠶
˟ᥙГᝐႄԁᬘឱӉ఼
ᮈᄧᑁ᭨૖ౝǎ᝻ܭа෦
ధԼΚၺ፦οΏၺᄋᦋǎឱ࠳፦ο
ᮋႁՍಬᄋ˅ˋցᤊᛢǎ
࠶
˟ᥙГᅍ༣ᝐႄԁᬘឱӉ
࠳൦᝻ܭᎷᭂ๹໾ິ˘ǎ
൦᝻ܭ˸ˁԼԫ๰͵໠ຶᄪధ๰͵ᄋࠕ
٩˸ˁԼᎷЦʾݡᔊၬ኏ǎ
࠶
፦οឮ௛௨ፍՍಬᄋ˅ˋ፦
οցΏၺᄋǎ˟ᥙГᝐႄԁ
ᬘᬕΏၺឮ௛˻ଣ҃ᄋܲឱӉᤊᛢ
ͶЦ߳፦οǎధ፦οڪᮍႁՍಬᄋ˅
ˋցᤊᛢǎ
1. ឱ󰪀឵ᤉឮ௛ǎ
2. ឱݱؔεߜᤉឮ௛ǎ
3. ឱญధᄋ᝞ᇩǎ
4. ឱᥗ߷ధᄋឮ௛ǎ
5. ឱӉڛ᭦ᤄබᄋڢஶΏၺశַǎ
6. ឱၺࣱ࣌ຎพశַǎ
7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ௒ឱᥗ
ཱིԉࠓᄋឮ௛ǎ
8. ឱӉ࠳శַ߸ᜊڛམ຺ᬅᤄ
ݡ఍ජྠ༰ߖЦ߳ၸམ᧛ᄋ᝻ܭ
Ӌ઻ҫ஋٩ǎ
9. ឱӉሩᬕ౞মତ݁଍ڢତ݁ᄋ߸М
ᜊᎷǎ଍ڢତ݁௨ႁˑ˕ତ܌଍གྷԤʸ˕
଍ڢ݁౟ǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১
ᄋତឱႄࢻట૲ʸ˕Սᤡᄋତǎ
10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼ᢇ҉
ᆢࡀЦญႄ຺ତ݁Ǎܴၺ᤮ତԤ᝻ܭ
ᤍ଍ܬǎ
11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ֘
ᦢǎ
12. ឱԷΏၺԉࠓ
૊ࠁᄋᬥ᠏ᩚ
׭ᄋଏᢽ౷ߖ
ʽᝉ౷஄౷֘ಹ
ߖǎᔫΏၺଏᢽ
౐ୄᤃ᝻ܭឱญ
߸М஋Ꮇ᝻ܭ
ᥙГଏᢽ֘᝻
ܭϛωᏬԫǎ
13. ᥆󰩧ႄᭈᲟ󰩤ఱˁΏၺశ᝻ܭ௒
ឱફѤႄ຺ତ݁ǎ
14. ధ፦οڪᮍႁՍಬᄋ፦οցᤊ
ᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦οΔݡႄ຺ጴ
ႄ຺ତ݁ԫ૰๰͵ุЛྮᗁЛ᝻ܭ
а᝻ܭᥔᭂ๹ԫ໾᝻ܭˁᑠ൥ࣣᤃͼ
ᜃ୒گǎ
15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ଍ڢ
εઑǎ
16. ᔫႄ຺ତ݁٩Ч
ᏺՍ٩ၺͼளႄᜊᎷ
ε᝾߳ܬᬥ௒Լ
ஶΨ୳ͼ࿅ঘǎ
17. శַᤡၺ๓
ફ2000ዜʿڢӞశ
ַᤡၺ᭥མࣝජό౏
ʿǎ
ࠬͶڃڛ൦ឮ௛˻ଣ҃ᄋМᦋ
ᦋଢᤙǍڐྠܧ௛Ꮼᤶᄋ૰݀
MUSIC Groupˁ᠈Ͷ᠋ǎ઀సԡஞ֘
ܲ᜻ᔫధటஉিˁԴᛢᤱᅽǎధᄋ
׹ಗڪ˟ЦՋᒮధᏩᄋ᠊ǎMIDAS,
KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY,
TURBOSOUND, TC ELECTRONIC, TC HELICON,
BEHRINGER, BUGERA, COOLAUDIO ֘EUROCOM
௨MUSIC Group IP Ltd.ОՄᄋ׹ಗญг׹
ಗǎ© MUSIC Group IP Ltd. 2017ྡీధǎ
ధУᮄˮᬸڅεοᄋᤡၺ౏൝ԤЦ߳ᄲУ
θ্ឱᄇᬇmusic-group.com/warrantyᎫቤಋ
ᄻߺ஠ᄋឡጻθ্ǎ
其他的重要信息
保修条款
法律声明

10 NuQ-AN Series Quick Start Guide 11
(1) LCD SCREEN displays the current DSP module and parameter settings.
(2) SETUP button steps through parameters within DSP processing modules.
(3) PROCESS button steps through the DSP processing modules.
(4) AUDIO LINK XLR connector provides an un-processed copy of the AUDIO INPUT signal.
(5) AUDIO INPUT combo jack accepts input signals using XLR, balanced ¼" TRS or unbalanced ¼"TSconnectors.
(6) POWER switch turns the unit on and o.
(7) AC INPUT accepts power connections from power cables tted with Neutrik powerCON twist-lockingconnectors.
(8) ENCODER KNOB toggles between Graphic and Edit modes (when pressed) and changes parameter values (when rotated).
(9) EXIT button returns to the top-level DSP screen when pressed.
(10) ENTER button saves changes and deactivates Edit mode when pressed.
(11) ULTRANET THRU sends out unprocessed digital audio from the ULTRANET IN connector to additional ULTRANET-equipped devices.
(12) USB connection enables rmware updates and remote control over parameters via computer. Pleasevisit turbosound.com to download DSP control software for
your computer.
(13) ULTRANET IN RJ45/Neutrik etherCON jack for connection to additional ULTRANET-equipped devices.
Networking capability
All NuQ-AN powered loudspeakers oer remote control via USB. The USB connection allows the user to congure and monitor all DSP parameters using dedicated
software for PC.
The DSP rmware can also be updated via the USB connection. Visitturbosound.com for the latest rmware version.
NuQ-AN speakers also oer proprietary ULTRANET networking capabilities through the ULTRANET IN and ULTRANET THRU connections using CAT5 cables with RJ45
connectors. ULTRANET allows the user to transmit unidirectionally up to 16 independent channels of 24-bit audio throughout the NuQ-AN system, aswell as other
ULTRANET-equipped devices such as digital mixers and personal monitor systems. Upto7devices can be connected in series on a single ULTRANET cable.
MIDAS M32
MIDAS DL16

12 NuQ-AN Series Quick Start Guide 13
NuQ-AN DSP Menu Structure
Fullrange Subwoofer Function
PROCESS EQ
None None Sets the frequency response to the default setting.
Live Live Sets the frequency response to a typical live sound setting.
Speech Speech Sets the frequency response for optimal speech intelligibility.
Playback Playback Sets the frequency response ideal for music playback.
User User Lets you dene your own frequency response setting by
entering the corresponding sub menu.
Sub menu
Low/ High Shelving Low/ High Shelving Lets you dene a low and high shelving lter.
Parametric 1 & 2 Parametric 1 & 2 Lets you dene a parametric bell-type EQ (Frequency, Qual.
and Gain).
XOVER
None - Unit is set for default full rangereproduction.
HP 120 Hz LP 120 Hz Preset with 120 Hz 24 dB / octave lter for crossover
between subwoofer and full-range speakers.
HP 100 Hz LP 100 Hz Preset with 100 Hz 24 dB / octave lter for crossover
between subwoofer and full-range speakers.
- NuQ82 Preset with ideal settings for use in combination with NuQ82
fullrangespeaker.
- NuQ102 Preset with ideal settings for use in combination with
NuQ102 fullrangespeaker.
- NuQ122 Preset with ideal settings for use in combination with
NuQ122 fullrangespeaker.
- NuQ152 Preset with ideal settings for use in combination with
NuQ152 fullrangespeaker.
NuQ115B - Preset with high pass alignment for NuQ115B subwoofer.
NuQ118B - Preset with high pass alignment for NuQ118B subwoofer.
User User User crossover sub menu for combination with other
fullrange or subwoofer speaker systems
Sub Menu
Freq Freq
Select the desired crossoverfrequency:
For fullrange systems: 75 Hz to 400 Hz
For subwoofer systems: 50 Hz to 150Hz
Phase Phase Adjust the absolute phase (0° or 180°)
FBQ
Auto Auto
Automatically sets as many lters as required. Whenever a
new feedback frequency is discovered, the rst lter will be
released to attenuate the new frequency, and so forth.
Single Single Activates the FBQ (feedback detection) functionality, up to
8 feedback lters
Fullrange Subwoofer Function
Learn Learn
Automatic procedure which searches for feedback
frequencies and locks settings after all 8 lters have
beenset.
WARNING!
Please use ear protection during this procedure. The
feedback signal may approach the system’s maximum
level, which may cause hearingdamage!
Reset Reset Resets all lters.
SETUP
(page 1) INPUT
Input Input
Lets you choose the audio input source. Choose between
Local (analogue Input) or ULTRANET (e.g.,P16 monitoring
system or M32audio via ULTRANET).
Volume Volume
Adjusts the input gain. With ULTRANET digital inputs over
a range from+ 10 dB to - 30 dB. With analogue input from
0 dB to -∞dB.
Sensitivity Sensitivity
Adjusts input sensitivity for maxium output when using an
analogue source +4 dBu for normal opperation, + 14 dBu
for high level input.
POSITION
Stand Floor For positioning the speaker on a pole mount stand
(fullrange) or on the oor(Subwoofer)
Wall Wall For positioning the speaker on or next to a wall (xed
install); alternatively as a monitor speaker (wedge).
Ceiling - For positioning the speaker on a wall next to the ceiling
(xed install)
Corner Corner
For positioning the speaker in a corner next to the
ceiling (xed install); Forpositioning the speaker in a
corner(subwoofer)
Screenshot update
DELAY
Delay Delay Adjusts the amount of delay (max300msec = 103.08 m or
338.19feet).
Unit Unit Selector between msec, meterandfeet.
LIMITER
Limit Limit
Adjust the limiter threshold for the input signal (from OFF
down to -30dB). This threshold adjustment allows you to
set a max output power which is below the loudspeaker
system’s rated max output.
SETUP
(page 2)
Version Version Displays the installed rmwareversion.
LOAD
1. - 20. 1. - 20.
To load a specic preset, turn the encoder to select the
desired peset’s number, and then either the ENTER button or
the encoder. When asked to conrm press the encoder again
or EXIT to abort.
SAVE
1. - 20. 1. - 20. To save a preset choose the respectivepreset slot and press
ENTER or theencoder.

14 NuQ-AN Series Quick Start Guide 15
Mounting and Fixing
NuQ-AN full-range series cabinets are designed with multiple internal rigging points to suit many possible mounting methods in permanent installations. NuQ-AN
series two-way cabinets are equipped with pole mount sockets for portable use on 35 mm speaker stands or poles. Bass cabinets are equipped with pole mount
receptacles that allow two-way cabinets to be mounted at the correct height.
TURBOSOUND wall and ceiling brackets are optionally available for installing NuQ-AN series cabinets. Someexamples are shownbelow.
Model Flying Yoke Swivel Bracket Swivel Extenders Eyebolts
NuQ82-AN NuQ82-FY NuQ82-SB NuQ82-EB M10
NuQ102-AN NuQ102-FY NuQ102-SB NuQ102-EB M10
NuQ122-AN NuQ122-FY – – M10
NuQ152-AN NuQ152-FY – – M10
NuQ102-SB NuQ102-SB + NuQ102-EB NuQ102-FY
QuNNuQ 8 BS-2 82-SB + NuQ 82-EB
NuQ152-FYNuQ122-FY
82-FYNuQ
Fullrange Subwoofer Function
Sub Menu
Save Preset Save Preset
Name the preset by choosing the characters with the
encoder and pressing to conrm each character. When
nished, press the ENTER button to save the preset.
SETUP
Contrast Contrast Adjust LCD panel contrast, The default contrast value is 15.
Screen Screen
ON: LCD screen saver (default) turnson automatically after
approx. 2minutes.
OFF : LCD turns o automatically after approx. 5 minutes.
Logo Logo
OFF: Deactivates front panel logo illumination. ON: Activates
front panel logo illumination. LIMIT: Logo will light up when
the limiter is active.
Sub Menu
Lock Lock
Lock the device and create a password by choosing the
password characters with the encoder and pressing to
conrm each character. Whennished press the ENTER
button. Unlock the device by entering the password or
connecting the unit via USB to a PC running propriety remote
software. Thesoftware does not require apassword.
Warning Warning In case of overheating, an alert appears on the LCD screen,
and the amplier will shut down until the unitcools.
LCD Graphic Indicators
To help the user immediately recognize that a parameter has been selected and changed from the initial default setting, the parameter’s related text on the top-level
screen will invert and change to black text on a white background. As an example, the following screenshots show how the text for the EQ function changes when the
NuQ-AN default EQ setting has been changed:
This indicator function occurs only on the main DSP menu level and works for all DSP-related functions, except for the LOAD, SAVE and SETUP sub-sections on the
second page of the top-level SETUP menu.

16 NuQ-AN Series Quick Start Guide 17
Suspending with Eyebolts
NuQ-AN cabinets can be suspended using optional eyebolts coupled to the internal rigging points provided on the top, bottom and sides.
Remove the appropriate countersunk screws and replace them withshoulder eyebolts, which must have a thread length of at least 18 mm. Use the rear rigging point to
angle the cabinet for optimum room coverage. Cabinets may be hung upside down if required.
IMPORTANT NOTE FOR ALL INSTALLATION METHODS: The mounting of a permanently installed sound system may be dangerous unless undertaken by qualied
personnel with the required experience and certication to perform the necessary tasks. Walls, oors or ceilings must be capable of safely and securely supporting the
actual load. Themounting accessory used must be safely and securely xed both to the loudspeaker and to the wall, oor or ceiling.
When mounting rigging components on walls, oors or ceilings, ensure that all xings and fasteners used are of an appropriate size and load rating. Wall and ceiling
claddings, and the construction and composition of walls and ceilings, all need to be taken into account when determining whether a particular xing arrangement
can be safely employed for a particular load. Cavity plugs or other specialist xings, if required, must be of an appropriate type, and must be tted and used in
accordance with the maker’sinstructions.
The operation of your speaker cabinet as part of a own system, if installed incorrectly and improperly, canpotentially expose persons to serious health risks and
even death. In addition, please ensure that electrical, mechanical and acoustic considerations are discussed with qualied and certied (by local state or national
authorities) personnel prior to any installation or ying.
Make sure that speaker cabinets are set up and own by qualied and certied personnel only, usingdedicated equipment and original parts and components
delivered with the unit. If any parts or components are missing please contact your Dealer before attempting to set up the system.
Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group, including the MUSIC Group companies listed on the enclosed
“Service Information Sheet”, assumes no liability for any damage or personal injury resulting from improper use, installation or operation of the product. Regular
checks must be conducted by qualied personnel to ensure that the system remains in a secure and stable condition. Make sure that, where the speaker is own, the
area underneath the speaker is free of human trac. Do not y the speaker in areas that can be entered or used by members of the public.
Speakers create a magnetic eld, even if not in operation. Therefore, please keep all materials that can be aected by such elds (discs, computers, monitors, etc) at a
safe distance. A safe distance is usually between 1 and 2 metres.

18 NuQ-AN Series Quick Start Guide 19
Technical Specications
NuQ82-AN (WH) NuQ102-AN (WH) NuQ122-AN (WH)
System
Frequency response 65 Hz – 18 kHz ±3 dB
55 Hz – 20 kHz -10 dB
55 Hz – 18 kHz ±3 dB
50 Hz – 20 kHz -10 dB
55 Hz – 18 kHz ±3 dB
50 Hz – 20 kHz -10 dB
Nominal dispersion 100° H x 60° V @ -6 dB points, rotatable 100° H x 60° V @ -6 dB points, rotatable 70° H x 70° V @ -6 dB points
Maximum SPL 122 dB peak 122 dB peak 131 dB peak
Crossover type Active Active Active
Transducers 1 x 8" (211.5 mm) LF driver
1 x 1" (25.4 mm) HFcompression driver
1 x 10" (261.5 mm) LF driver
1 x 1" (25.4 mm) HFcompression driver
1 x 12" ( 315.5) LF driver
1 x 1" (25.4 mm)
HF compression driver
Limiter Independent HF, LF,
peak and rms
Independent HF, LF,
peak and rms
Independent HF, LF,
peak and rms
Amplier
Maximum Output Power* 600 W 600 W 2500 W
Type Class-D Class-D Class-D
Protection Short circuit, thermal Short circuit, thermal Short circuit, thermal
Connectors
Input/link 1 x combo jack/XLR, 1 x XLR 1 x combo jack/XLR, 1 x XLR 1 x combo jack/XLR, 1 x XLR
Sensitivity +4dBu or +14 dBu software switchable +4dBu or +14 dBu software switchable +4dBu or +14 dBu software switchable
Input impedance 40 k balanced 40 k balanced 40 k balanced
Maximum input level +22 dBu +22 dBu +22 dBu
Ultranet input/link 2 x RJ45 2 x RJ45 2 x RJ45
Mains Supply Neutrik powerCON 20A Neutrik powerCON 20A Neutrik powerCON 20A
Controls
DSP Rotary push-encoder and levelcontrol
Buttons for process, setup, exit, enter
Rotary push-encoder and levelcontrol
Buttons for process, setup, exit, enter
Rotary push-encoder and levelcontrol
Buttons for process, setup, exit, enter
User DSP Functions
Factory EQ Presets Positioning, sound mode, FBQ Positioning, sound mode, FBQ Positioning, sound mode, FBQ
Display LCD 128 x 32, blue, backlit LCD 128 x 32, blue, backlit LCD 128 x 32, blue, backlit
Delay 0 - 300 ms 0 - 300 ms 0 - 300 ms
Equalisation High and low shelving EQ
2 x parametric EQ
High and low shelving EQ
2 x parametric EQ
High and low shelving EQ
2 x parametric EQ
Limiter Zero attack input limiter Zero attack input limiter Zero attack input limiter
Presets 20 total presets,
19 user-denable
20 total presets,
19 user-denable
20 total presets,
19 user-denable
Crossover High pass L-R 24 dB/oct High pass L-R 24 dB/oct High pass L-R 24 dB/oct
Protection Lock-out function for allsettings Lock-out function for allsettings Lock-out function for allsettings
Ultranet Digital Network
Digital processing
A/D conversion 24-bit,44.1/48kHz sample rate 24-bit,44.1/48kHz sample rate 24-bit,44.1/48kHz sample rate
Converter type 24-bit, delta-sigma 24-bit, delta-sigma 24-bit, delta-sigma
System
Signal 16 channels 16 channels 16 channels
Latency < 0.9 ms < 0.9 ms < 0.9 ms
Frequency response 20 Hz to 20 kHz (+0 / -3 dB) 20 Hz to 20 kHz (+0 / -3 dB) 20 Hz to 20 kHz (+0 / -3 dB)
Dynamic range Typical 92 dB Typical 92 dB Typical 92 dB
Cabling
Cables Shielded CAT5 Shielded CAT5 Shielded CAT5
Cable length Max. 246 ft / 75 m recommended Max. 246 ft / 75 m recommended Max. 246 ft / 75 m recommended
NuQ82-AN (WH) NuQ102-AN (WH) NuQ122-AN (WH)
Power Supply
Power consumption 80 W @ ⁄max power 80 W @ ⁄max power 90 W @ ⁄max power
Voltage (fuses)
USA / Canada 120 V~, 60 Hz (T 6.3 A H 250 V) 120 V~, 60 Hz (T 6.3 A H 250 V) 120 V~, 60 Hz (T 15 A H 250 V)
UK / Australia / Europe 220-240 V~, 50/60 Hz
(T 3.15 A H 250 V)
220-240 V~, 50/60 Hz
(T 3.15 A H 250 V)
220-240 V~, 50/60 Hz
(T 10 A H 250 V)
Korea / China 220-240 V~, 50/60 Hz
(T 3.15 A H 250 V)
220-240 V~, 50/60 Hz
(T 3.15 A H 250 V)
220-240 V~, 50/60 Hz
(T 10 A H 250 V)
Japan 100 V~, 50/60 Hz
(T 6.3 A H 250 V)
100 V~, 50/60 Hz
(T 6.3 A H 250 V)
100 V~, 50/60 Hz
(T 15 A H 250 V)
Enclosure
Dimensions HWD 464 x 274 x 252 mm
(18.3 x 10.8 x 9.9")
525 x 318 x 281 mm
(20.7 x 12.5 x 11.1")
656 x 374 x 340 mm
(25.8 x 14.7 x 13.4")
Net weight 11.3 kg (24.9 lbs) 13.7 kg (30.2 lbs) 20.2 kg (44.5 lbs)
Construction 12 mm (½") birch plywood 12 mm (½") birch plywood 15 mm (⁄") birch plywood
Finish Semi matt black paint Semi matt black paint Semi matt black paint
Grille Powder coated perforatedsteel Powder coated perforatedsteel Powder coated perforatedsteel
Flying hardware M10 x 8 points; M8 x 1 point M10 x 8 points; M8 x 1 point M10 x 8 points
Accessories
NuQ82-SB swivel bracket forNuQ82
NuQ82-EB extension bracketfor NuQ82
NuQ82-FY ying yoke forNuQ82
NuQ102-SB swivel bracket forNuQ102
NuQ102-EB extension bracketfor NuQ102
NuQ102-FY ying yoke forNuQ102
NuQ122-FY ying yoke forNuQ122

20 NuQ-AN Series Quick Start Guide 21
Technical Specications
NuQ152-AN (WH) NuQ115B-AN (WH) NuQ118B-AN (WH)
System
Frequency response 55 Hz – 18 kHz ±3 dB
50 Hz – 20 kHz -10 dB
45 Hz – 150 Hz ±3 dB
38 Hz – 200 Hz -10 dB
40 Hz – 150 Hz ±3 dB
33 Hz – 150 Hz -10 dB
Nominal dispersion 70° H x 70° V @ -6 dB points Half Space Half Space
Maximum SPL 133 dB peak 135 dB peak 136 dB peak
Crossover type Active Active Active
Transducers
1 x 15" (393.5 mm) LF driver
1 x 1" (25.4 mm)
HF compression driver
1 x 15" (387 mm) LF driver 1 x 18" (460 mm) LF driver
Limiter Independent HF, LF,
peak and rms Peak and rms Peak and rms
Amplier
Maximum Output Power* 2500 W 3000 W 3000 W
Type Class-D Class-D Class-D
Protection Short circuit, thermal Short circuit, thermal Short circuit, thermal
Connectors
Input/link 1 x combo jack/XLR, 1 x XLR 1 x combo jack/XLR, 1 x XLR 1 x combo jack/XLR, 1 x XLR
Sensitivity +4dBu or +14 dBu software switchable +4dBu or +14 dBu software switchable +4dBu or +14 dBu software switchable
Input impedance 40 k balanced 40 k balanced 40 k balanced
Maximum input level +22 dBu +22 dBu +22 dBu
Ultranet input/link 2 x RJ45 2 x RJ45 2 x RJ45
Mains Supply Neutrik powerCON 20A Neutrik powerCON 20A Neutrik powerCON 20A
Controls
DSP Rotary push-encoder and levelcontrol
Buttons for process, setup, exit, enter
Rotary push-encoder and levelcontrol
Buttons for process, setup, exit, enter
Rotary push-encoder and levelcontrol
Buttons for process, setup, exit, enter
User DSP Functions
Factory EQ Presets Positioning, sound mode, FBQ Positioning, sound mode Positioning, sound mode
Display LCD 128 x 32, blue, backlit LCD 128 x 32, blue, backlit LCD 128 x 32, blue, backlit
Delay 0 - 300 ms 0 - 300 ms 0 - 300 ms
Equalisation High and low shelving EQ
2 x parametric EQ
High and low shelving EQ
2 x parametric EQ
High and low shelving EQ
2 x parametric EQ
Limiter Zero attack input limiter Zero attack input limiter Zero attack input limiter
Presets 20 total presets,
19 user-denable
20 total presets,
19 user-denable
20 total presets,
19 user-denable
Crossover High pass L-R 24 dB/oct Low pass L-R 24 dB/oct Low pass L-R 24 dB/oct
Protection Lock-out function for allsettings Lock-out function for allsettings Lock-out function for allsettings
Ultranet Digital Network
Digital processing
A/D conversion 24-bit,44.1/48kHz sample rate 24-bit,44.1/48kHz sample rate 24-bit,44.1/48kHz sample rate
Converter type 24-bit, delta-sigma 24-bit, delta-sigma 24-bit, delta-sigma
System
Signal 16 channels 16 channels 16 channels
Latency < 0.9 ms < 0.9 ms < 0.9 ms
Frequency response 20 Hz to 20 kHz (+0 / -3 dB) 20 Hz to 20 kHz (+0 / -3 dB) 20 Hz to 20 kHz (+0 / -3 dB)
Dynamic range Typical 92 dB Typical 92 dB Typical 92 dB
Cabling
Cables Shielded CAT5 Shielded CAT5 Shielded CAT5
Cable length Max. 246 ft / 75 m recommended Max. 246 ft / 75 m recommended Max. 246 ft / 75 m recommended
NuQ152-AN (WH) NuQ115B-AN (WH) NuQ118B-AN (WH)
Power Supply
Power consumption 90 W @ ⁄max power 180 W @ ⁄max power 180 W @ ⁄max power
Voltage (fuses)
USA / Canada 120 V~, 60 Hz (T 15 A H 250 V) 120 V~, 60 Hz (T 15 A H 250 V) 120 V~, 60 Hz (T 15 A H 250 V)
UK / Australia / Europe 220-240 V~, 50/60 Hz
(T 10 A H 250 V)
220-240 V~, 50/60 Hz
(T 10 A H 250 V)
220-240 V~, 50/60 Hz
(T 10 A H 250 V)
Korea / China 220-240 V~, 50/60 Hz
(T 10 A H 250 V)
220-240 V~, 50/60 Hz
(T 10 A H 250 V)
220-240 V~, 50/60 Hz
(T 10 A H 250 V)
Japan 100 V~, 50/60 Hz
(T 15 A H 250 V)
100 V~, 50/60 Hz
(T 15 A H 250 V)
100 V~, 50/60 Hz
(T 15 A H 250 V)
Enclosure
Dimensions HWD 712 x 430 x 385 mm
(28.0 x 16.9 x 15.2")
520 x 580 x 620 mm
(20.4 x 22.8 x 24.4")
770 x 580 x 700 mm
(30.3 x 22.8 x 27.5")
Net weight 23.6 kg (52.0 lbs) 37 kg (81.5 lbs) 57.9 kg (127.6 lbs)
Construction 15 mm (⁄") birch plywood 18 mm (¾") birch plywood 18 mm (¾") birch plywood
Finish Semi matt black paint Semi matt black paint Semi matt black paint
Grille Powder coated perforatedsteel Powder coated perforatedsteel Powder coated perforatedsteel
Flying hardware M10 x 8 points M10 x 16 points M10 x 16 points
Accessories
NUQ152-FY ying yoke forNuQ152
*independent of limiters and driver protection circuits
Only qualied personnel are allowed to modify the AC-Main cord and to adhere to all applicable national standards.

22 NuQ-AN Series Quick Start Guide 23
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: MUSIC Group Research
UK Limited
Address: Klark Industrial Park,
Walter Nash Road,
Kidderminster. Worcestershire. DY11 7HJ. England.
Phone Number: [phone]
NuQ-AN Series
This equipment has been tested and found to comply withthe limits for a Class B digital device,
pursuant to part 15of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the
followingmeasures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technicianforhelp.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, includinginterference that may cause
undesired operation.
Important information:
Changes or modications to the equipment not expressly approved by
MUSIC Group can void the user’s authority to use the equipment.
NuQ-AN Series
Other important information
1. Register online. Please register your new
MUSIC Group equipment right after you purchase it by visiting
turbosound.com. Registering your purchase using our simple
online form helps us to process your repair claims more
quickly and eciently. Also, read the terms and conditions of
our warranty, ifapplicable.
2. Malfunction. Should your MUSICGroup Authorized
Reseller not be located in your vicinity, youmay contact the
MUSICGroup Authorized Fulller for your country listed
under “Support” at turbosound.com. Shouldyour country
not be listed, please check if your problem can be dealt with
by our “OnlineSupport” which may also be found under
“Support” at turbosound.com. Alternatively, please submit an
online warranty claim at turbosound.com BEFORE returning
theproduct.
3. Power Connections. Beforeplugging the unit into
a power socket, pleasemake sure you are using the correct
mains voltage for your particular model. Faultyfuses
must be replaced with fuses of the same typeand rating
withoutexception.
Important information

This file was downloaded from the site
mans.io
Instruction manuals and user guides
Samsung
Pioneer
Alpine
LG
Dell
Sharp
Sony
Philips
Epson
Netgear